Search

Agroforestry creates value but also a huge amount of waste outside its value chain. Tree pruning is an example of such a low value waste, that is typically discarded or incinerated in the fields or used to recover energy. Nonetheless, tree prunings are rich in wood fibers that can be used as polymer reinforcement. Although there are some bio-based polymers, the majority of industries use oil-based ones. The election of the materials is usually based on a ratio between properties and cost. Bio-based polymers are more expensive than oil-based ones. This work shows how a bio-polyethylene matrix can be reinforced with fibers from orange tree prunings to obtain materials with notable tensile properties. These bio-based materials can show a balanced cost due to the use of a cheap reinforcement with an expensive matrix. The matrix used showed a tensile strength of 18.65 MPa, which reached 42.54 MPa after the addition of 50 wt.% of reinforcement. The obtained values allow the use of the studied composite to replace polypropylene and some of its composites under tensile loads This research was funded by the CTQ2010-21660-C03-03 grant of the Spanish ministry of science and innovation

The present paper investigates the acoustic properties of natural fiber reinforced composites. Fibers from orange tree pruning were obtained and subject to different treatments in order to obtain mechanical, thermomechanical and chemi-thermomechanical pulps. These pulps were used as reinforcement for a polypropylene matrix. The obtained composite materials were submitted to acoustical tests in an impedance tubes device. The transmission losses obtained against the fiber content were obtained and discussed. Latter it was researched the influence of the fiber treatments on the soundproof characteristics. A numerical method was used to preview the acoustic insulation of the materials against the sound frequency. Finally the results were compared with that of the most usual lightweight soundproof solutions. (C) 2014 Elsevier Ltd. All rights reserved.

In the present work, a functionalization of polylactic acid (PLA) has been carried out to anchor maleic anhydride onto the main polymer chain to promote improvement in the compatibility of this polymer matrix with cellulose fibres. Low-molecular-weight PLA has been reacted with maleic anhydride following different procedures: a bulk reaction in an internal mixer and a solution reaction. The presence of oxygen during bulk processing did not allow for functionalization, guiding the reaction towards a decrease in the molecular weight of the material. On the contrary, a controlled reaction under an inert atmosphere in the presence of dioxane as the solvent, at reflux temperature, led to the functionalization of the polymer reaching different yields depending on the percentage of radical initiator and maleic anhydride added and reaction time. The yield of functionalization has been monitored by acid number titration as well as 1H NMR, with optimal yield values of functionalization being up to 3.5%. The PLA-functionalized formula has been used to make commercial PLA compatible with cellulose fibres derived from a thermomechanical treatment. The addition of 10% w/w of fibres to PLA increases the ultimate tensile strength (UTS) of PLA by up to 15%. The incorporation of 4 w/w of the already-functionalized coupling agent to the composite produces improvements in UTS of up to 24% regarding PLA, which confirms the functionalization from a performance point of view This research was funded by Spanish government MINECO in the framework of project MAT2017-83347-R

The textile industry generates a large amount of byproducts that must be treated before being recycled or disposed of. The treatments to extract the dyeing agents are mandatory, and involve costs and interaction with toxic reagents. A relevant amount of such byproducts are short cotton dyed fibers. Cotton fibers are high-quality cellulosic fibers and can be used as composite reinforcement. In this paper, dyed cotton fibers were used to formulate, obtain and tensile test composite materials. The impact of the presence of dyes was studied and such dyes enhanced the interphase between the matrix and the reinforcement. On the other hand, when a coupling agent was incorporated to the formulation of the composites, the dyes hindered the chemical interactions between the maleic acid and the OH groups of the cellulosic fibers. Nonetheless, the composite materials showed competitive mechanical properties that were better than other natural fiber-reinforced composites and comparable to some glass fiber-based ones. Dyed cotton fibers can be used as reinforcement without further treatment, increasing the value chain of the textile industry and decreasing the chemical treatments necessary to recycle or dispose of dyed textile fibers. © The Author(s) 2018.

Due to its high biocompatibility, bio-degradability, and low cost, cellulose finds application in disparate areas of research. Here we focus our attention on the potential applications of cellulose nanofiber in cement-basedmaterials for the building sector. We first describe the chemical/morphological composition of cellulose fibers, their process and treatment, the characterization of cement-based composites, and their flexural strength. In recent research in this field, cellulose has been considered in the form of nano-sized particles, i.e., cellulose nanofibers (CNF) or cellulose nanocrystals (CNC). CNF and CNC are used for several reasons, including their mechanical and thermal properties, their extended surface area and lowtoxicity. This study presents some potential applications of lignocellulosic micro/nanofibers (LCMNF) in cement-based composites in order to improve flexural strength. Samples were made with 0.5-1.0-1.5-2.0 wt% of LCMNF obtained from pine sawdust, CEMI (Portland) and a 1:3 cement-water ratio. The composites were then tested for flexural strength at 7, 14, and 28 days and the evolution of flexural strength was assessed after water immersion during 72 h. Scanning electron microscopy was employed to visualize the bond between LCMNF and the cement matrix. Results showed that LCMNF improved the flexural strength of the composite in all the dosages used. © 2019 by the authors.

Poly(lactic acid) (PLA) is one of the most well-known biopolymers. PLA is bio-based, biocompatible, biodegradable, and easy to produce. This polymer has been used to create natural fiber reinforced composites. However, to produce high-performance and presumably biodegradable composites, the interphase between PLA and natural fibers still requires further study. As such, we aimed to produce PLA-based composites reinforced with a commercial bleached kraft eucalyptus pulp. To become a real alternative, fully biodegradable composites must have similar properties to commercial materials. The results found in this research support the competence of wood fiber reinforced PLA composites to replace other glass fiber reinforced polypropylene composites from a tensile property point of view. Furthermore, the micromechanics analysis showed that obtaining strong interphases between the PLA and the reinforcement is possible without using any coupling agent. This work shows the ability of totally bio-based composites that fulfill the principles of green chemistry to replace composites based on polyolefin and high contents of glass fiber. To the best knowledge of the authors, previous studies obtaining such properties or lower ones involved the use of reagents or the modification of the fiber surfaces&rsquo

The replacement of commodity polyolefin, reinforced with glass fiber (GF), by greener alternatives has been a topic of research in recent years. Cellulose fibers have shown, under certain conditions, enough tensile capacities to replace GF, achieving competitive mechanical properties. However, if the objective is the production of environmentally friendlier composites, it is necessary to replace oil-derived polymer matrices by bio-based or biodegradable ones, depending on the application. Polyamide 11 (PA11) is a totally bio-based polyamide that can be reinforced with cellulosic fibers. Composites based on this polymer have demonstrated enough tensile strength, as well as stiffness, to replace GF-reinforced polypropylene (PP). However, flexural properties are of high interest for engineering applications. Due to the specific character of short-fiber-reinforced composites, significant differences are expected between the tensile and flexural properties. These differences encourage the study of the flexural properties of a material prior to the design or development of a new product. Despite the importance of the flexural strength, there are few works devoted to its study in the case of PA11-based composites. In this work, an in-depth study of the flexural strength of PA11 composites, reinforced with Stoneground wood (SGW) from softwood, is presented. Additionally, the results are compared with those of PP-based composites. The results showed that the SGW fibers had lower strengthening capacity reinforcing PA11 than PP. Moreover, the flexural strength of PA11-SGW composites was similar to that of PP-GF composites.

Stiffness is one of the most relevant properties of composite materials. Although fiberglass has been traditionally used as reinforcement, natural fibers are seen as possible replacements due to concerns for environmental protection. In this work fibers from orange tree prunings were prepared and converted into mechanical, thermomechanical and chemi-thermomechanical pulps, to be used as reinforcement for polypropylene. Polypropylene composite materials with 20–50% of reinforcing fibers were prepared and mechanically characterized. The intrinsic Young's modulus of the fibers was back calculated by means of the Hirsch model. The moduli were also obtained by Halpin-Tsai equations with Tsai-Pagano methods and then compared to establish the influence of the aspect ratio. Finally, a fiber tensile modulus factor was defined in order to characterize the contribution of the fibers to the Young's moduli of the composites. POLYM. COMPOS., 34:1840–1846, 2013. © 2013 Society of Plastics Engineers

A major drawback of natural-based composites is the incorporation of reinforcements that are less thermally stable than the matrix; therefore, the thermal properties of the resultant composite material needs to be studied. In this work, orange wood fibers were used to reinforce polypropylene. The effects on the thermal properties of the polymeric matrix were analyzed. To this end, differential scanning calorimetry (DSC), thermogravimetry (TGA), thermomechanical analysis (TMA), and dynamic-mechanical analysis (DMA) were performed. It was found that the degradation of the material took place in two distinct phases: the reinforcement, close to 250 degrees C, and the matrix, above 340 degrees C. DSC results showed that fiber reinforcement did not influence the transition temperatures of the materials, although it did affect the polymer crystallinity value, increasing by 7% when the composite is reinforced with 50% of the lignocellulosic reinforcement. The coefficient of expansion obtained by TMA indicated that thermal expansion decreased as the amount of reinforcement increased. DMA assays showed that the reinforcement did not modify the glass transition (20 to 25 degrees C) temperature and confirmed that the addition of reinforcement increased the crystallinity of the product The authors are grateful for the support of the EMCI - Ministerio de Ciencia e Innovacion (MICINN) for funding the research by the specific Research Program CTQ2010-21660-C03-03

This paper explores the evolution in the tensile strength of orange pruning fiber-reinforced polypropylene composites. The exploitation of these pruning"s can effectively avoid incineration, with the consequence of CO2 emissions and fire risk, while extending the value chain of the agricultural industry. This biomass was subjected to three different treatments yielding mechanical, thermomechanical, and chemi-thermomechanical pulps. It was found that 20 to 50% of these pulps, together with a coupling agent, were used as polypropylene reinforcement. The evolution in the tensile strength and morphological properties of the fibers, and the effect of treatments on these properties were analyzed. A modified rule of mixtures (mROM) was used to analyze the micromechanical properties of the interface. In addition, the mechanical properties were weighted against the fiber treatment yields. Finally, factors to compute the net contribution of the fibers to the final strength of the composite materials were proposed The authors are grateful for the support of the EMCI - Ministerio de Ciencia e Innovacion (MICINN) for funding the research by the specific research program, CTQ2010-21660-C03-03

This work explores the use of mechanical (MP), thermomechanical (TMP), and chemi-thermomechanical (CTMP) pulps from orange tree pruning fibers (OPF) as reinforcing elements of polypropylene (PP) composites. Due to the nature of the natural fibers, the use of a coupling agent is needed to attain a good interface and to prevent fiber slippage from the matrix. The main objective of the present work was to investigate the orientation factor, the interfacial shear strength, and the intrinsic strength of the OPF. Coupled and non-coupled composites were formulated and tested, optimizing the coupling agent content with the objective of maximizing the tensile strength of the composites. Hirsch and Kelly-Tyson models and the Bowyer-Bader methodology were used to compute the micromechanic properties. The contribution of subcritical, supercritical fibers, and matrix were also calculated The authors are grateful for the support of the EMCI - Ministerio de Ciencia e Innovacion (MICINN) for funding the research by the specific Research Program CTQ2010-21660-C03-03