Search

The encapsulation of peptides and proteins in nanosystems has been extensively investigated for masking unfavorable biopharmaceutical properties, including short half-life and poor permeation through biological membranes. Therefore, the aim of this work was to encapsulate a small antimicrobial hydrophilic peptide (H-Ser-Pro-Trp-Thr-NH2, FS10) in PEG-PLGA (polyethylene glycol-poly lactic acid-co-glycolic acid) nanoparticles (Nps) and thereby overcome the common limitations of hydrophilic drugs, which because they facilitate water absorption suffer from rapid degradation. FS10 is structurally related to the well-known RNAIII inhibiting peptide (RIP) and inhibits S. aureus biofilm formation. Various parameters, including different method (double emulsion and nanoprecipitation), pH of the aqueous phase and polymeric composition, were investigated to load FS10 into PEG-PLGA nanoparticles. The combination of different strategies resulted in an encapsulation efficiency of around 25% for both the double emulsion and the nanoprecipitation method. It was found that the most influential parameters were the pH—which tailors the peptides charge—and the polymeric composition. FS10-PEG-PLGA nanoparticles, obtained under optimized parameters, showed size lower than 180 nm with zeta potential values ranging from −11 to −21 mV. In vitro release studies showed that the Nps had an initial burst release of 48–63%, followed by a continuous drug release up to 21 h, probably caused by the porous character of the Nps. Furthermore, transmission electron microscopy (TEM) analysis revealed particles with a spherical morphology and size of around 100 nm. Antimicrobial assay showed that the minimum inhibitory concentration (MIC) of the FS10-loaded Nps, against S. aureus strains, was lower (>128 µg/mL) than that of the free FS10 (>256 µg/mL). The main goal of this work was to develop polymeric drug delivery systems aiming at protecting the peptide from a fast degradation, thus improving its accumulation in the target site and increasing the drug-bacterial membrane interactions. [ABSTRACT FROM AUTHOR]

The encapsulation of peptides and proteins in nanosystems has been extensively investigated for masking unfavorable biopharmaceutical properties, including short half-life and poor permeation through biological membranes. Therefore, the aim of this work was to encapsulate a small antimicrobial hydrophilic peptide (H-Ser-Pro-Trp-Thr-NH2, FS10) in PEG-PLGA (polyethylene glycol-poly lactic acid-co-glycolic acid) nanoparticles (Nps) and thereby overcome the common limitations of hydrophilic drugs, which because they facilitate water absorption suffer from rapid degradation. FS10 is structurally related to the well-known RNAIII inhibiting peptide (RIP) and inhibits S. aureus biofilm formation. Various parameters, including different method (double emulsion and nanoprecipitation), pH of the aqueous phase and polymeric composition, were investigated to load FS10 into PEG-PLGA nanoparticles. The combination of different strategies resulted in an encapsulation efficiency of around 25% for both the double emulsion and the nanoprecipitation method. It was found that the most influential parameters were the pH—which tailors the peptides charge—and the polymeric composition. FS10-PEG-PLGA nanoparticles, obtained under optimized parameters, showed size lower than 180 nm with zeta potential values ranging from −11 to −21 mV. In vitro release studies showed that the Nps had an initial burst release of 48–63%, followed by a continuous drug release up to 21 h, probably caused by the porous character of the Nps. Furthermore, transmission electron microscopy (TEM) analysis revealed particles with a spherical morphology and size of around 100 nm. Antimicrobial assay showed that the minimum inhibitory concentration (MIC) of the FS10-loaded Nps, against S. aureus strains, was lower (>128 µg/mL) than that of the free FS10 (>256 µg/mL). The main goal of this work was to develop polymeric drug delivery systems aiming at protecting the peptide from a fast degradation, thus improving its accumulation in the target site and increasing the drug-bacterial membrane interactions.

Abstract: Staphylococci are a major cause of infections associated with indwelling medical devices. Biofilm formation on these devices adds to the antibiotic resistance seen among clinical isolates. RNAIII-inhibiting peptide (RIP) is a heptapeptide that inhibits staphylococcal pathogenesis, including biofilm formation, by obstructing quorum sensing mechanisms. Bismuth ethanedithiol (BisEDT) also prevents biofilm formation at subinhibitory concentrations. RIP and BisEDT were combined to prevent infections in a rat graft model, using antibiotic sensitive and resistant strains of Staphylococcus aureus and Staphylococcus epidermidis. BisEDT, RIP, or rifampin, or their combinations reduced the graft associated bacterial load over seven days. BisEDT–RIP was the best combination, reducing bacterial load to undetectable levels. BisEDT–RIP may prove useful for coating medical devices to prevent staphylococcal infections. [Copyright &y& Elsevier]

S. aureus under the biofilm mode of growth is often related to several nosocomial infections, more frequently associated with indwelling medical devices (catheters, prostheses, portacaths or heart valves). As a biofilm, the biopolymer matrix provides an excellent growth medium, increasing the tolerance to antibiotics and host immune system. To date, the antimicrobial therapy alone is not effective. A novel strategy to prevent biofilm formation is based on the interference with the bacterial cell-cell communication, a process known as quorum sensing (QS) and mediated by the RNA-III-activating peptide (RAP) and its target protein TRAP (Target of RAP). The RNAIII inhibiting peptide (RIP) is able to inhibit S. aureus pathogenesis by disrupting QS mechanism competing with RAP, thus inhibiting the phosphorylation of TRAP. This alteration leads to a reduced adhesion and to the inhibition of RNAIII synthesis, with the subsequent suppression of toxins synthesis. The present paper will provide an overview on the activity and potential applications of RIP as biofilm inhibiting compound, useful in the management of S. aureus biofilm infections. Moreover, medicinal chemistry strategies have been examined to better understand which modifications and/or structure alterations were able to produce new derivatives of this QS inhibitor with an improved antibiofilm activity., (Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.net.)