Search

β-FeSi2 with the addition of B4C nanoparticles was manufactured by sintering mechanically alloyed Fe and Si powders with Mn, Co, Al, P as p and n-type dopants. The consolidated samples were subsequently annealed at 1123 K for 36 ks. XRD analysis of sinters after annealing confirmed nearly full transformation from α and ε into thermoelectric β-FeSi2 phase. SEM observations of samples surface were compliant with the diffraction curves. TEM observations allowed to depict evenly distributed B4C nanoparticles thorough material, with no visible aggregates and establish grain size parameter d2 < 500 nm. All dopants contributed to lower thermal conductivity and Seebeck coefficient, with Co having strongest influence on increasing electrical conductivity in relation to reference FeSi2. Combination of the addition of Co as dopant and B4C nanoparticles as phonon scatterer resulted in dimensionless figure of merit ZT reaching 7.6 × 10–2 at 773 K for Fe0.97Co0.03Si2 compound. Comparison of the thermoelectric properties of examined sinters to the previously manufactured of the same stoichiometry but without B4C nanoparticles revealed theirs overall negative influence.

One of the ways to decrease thermal conductivity is nano structurization. Cobalt triantimonide (CoSb3) samples with added indium or tellurium were prepared by the direct fusion technique from high purity elements. Ingots were pulverized and re-compacted to form electrodes. Then, the pulsed plasma in liquid (PPL) method was applied. All materials were consolidated using rapid spark plasma sintering (SPS). For the analysis, methods such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM) with a laser flash apparatus (LFA) were used. For density measurement, the Archimedes’ method was used. Electrical conductivity was measured using a standard four-wire method. The Seebeck coefficient was calculated to form measured Seebeck voltage in the sample placed in a temperature gradient. The preparation method allowed for obtaining CoSb3 nanomaterial with significantly lower thermal conductivity (10 Wm–1K–1 for pure CoSb3 and 3 Wm–1K–1 for the nanostructured sample in room temperature (RT)). The size of crystallites (from SEM observations) in the powders prepared was about 20 nm, joined into larger agglomerates. The Seebeck coefficient, α, was about –200 µVK–1 in the case of both dopants, In and Te, in microsized material and about –400 µVK–1 for the nanomaterial at RT. For pure CoSb3, α was about 150 µVK–1 and it stood at –50 µVK–1 for nanomaterial at RT. In bulk nanomaterial samples, due to a decrease in electrical conductivity and inversion of the Seebeck coefficient, there was no increase in ZT values and the ZT for the nanosized material was below 0.02 in the measured temperature range, while for microsized In-doped sample it reached maximum ZT = 0.7 in (600K).

This paper presents corrosion resistance results of a 12Cr ferritic ODS steel (Fe-12Cr-2W-0.5Zr-0.3Y 2 O 3 ) fabricated via a powder metallurgy route as a prospective applicant for fuel cladding materials. In a spent nuclear fuel reprocessing facility, nitric acid serves as the primary solvent in the PUREX method. Therefore, fundamental immersion and electrochemical tests were conducted in various nitric acid solutions to evaluate corrosion degradation behavior. Additionally, polarization tests were also performed in 0.61 M of sodium chloride solutions (seawater-like atmosphere) as a more general, all-purpose procedure that produces valid comparisons for most metal alloys. For comparison, martensitic X46Cr13 steel was also examined under the same conditions. In general, the corrosion resistance of the 12Cr ODS steel was better than its martensitic counterpart despite a lower nominal chromium content. Potentiodynamic polarization plots exhibited a lower corrosion current and higher breakdown potentials in chloride solution in the case of the ODS steel. It was found that the corrosion rate during immersion tests was exceptionally high in diluted (0.1-3 M) boiling nitric acid media, followed by its sharp decrease in more concentrated solutions (>4 M). The results of the polarization plots also exhibited a shift toward more noble corrosion potential as the concentrations increased from 1 M to 4 M of HNO 3 . The results on corrosion resistance were supported by LSCM and SEM observations of surface topology and corrosion products.

Magnesium (Mg) and its alloys offer promise for aerospace, railway, and 3D technology applications, yet their inherent limitations, including inadequate strength, pose challenges. Magnesium matrix composites, particularly with metallic reinforcements like titanium (Ti) and its alloys, present a viable solution. Therefore, this study investigates the impact of Ti6Al4V reinforcement on AZ31 magnesium alloy composites produced using pulse plasma sintering (PPS). Results show enhanced microhardness of the materials due to improved densification and microstructural refinement. However, Ti6Al4V addition decreased corrosion resistance, leading to strong microgalvanic corrosion and substrate dissolution. Understanding these effects is crucial for designing Mg-based materials for industries like petrochemicals, where degradation-resistant materials are vital for high-pressure environments. This research provides valuable insights into developing Mg-Ti6Al4V composites with tailored properties for diverse industrial applications, highlighting the importance of considering corrosion behavior in material design. Further investigation is warranted to establish predictive correlations between Ti6Al4V content and corrosion rate for optimizing composite performance.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of an SPS device used for material processing and synthesis in both scientific and industrial applications and aims to present manufacturing methods and the versatility of an SPS device, presenting examples of processing Arc-Melted- (half-Heusler, cobalt triantimonide) and Self-propagating High-temperature Synthesis (SHS)-synthesized semiconductor (bismuth telluride) materials. The SPS system functionality development is presented, the purpose of which was to broaden the knowledge of the nature of SPS processes. This approach enabled the precise design of material sintering processes and also contributed to increasing the repeatability and accuracy of sintering conditions.

Hemocompatibility is the most significant criterion for blood-contacting materials in successful in vivo applications. Prior to the clinical tests, in vitro analyses must be performed on the biomaterial surfaces in accordance with the ISO 10993-4 standards. Designing a bio-functional material requires engineering the surface structure and chemistry, which significantly influence the blood cell activity according to earlier studies. In this study, we elucidate the role of surface terminations and polymorphs of SiC single crystals in the initial stage of the contact coagulation. We present a detailed analysis of phase, roughness, surface potential, wettability, consequently, reveal their effect on cytotoxicity and hemocompatibility by employing live/dead stainings, live cell imaging, ELISA and Micro BCA protein assay. Our results showed that the surface potential and the wettability strongly depend on the crystallographic polymorph as well as the surface termination. We show, for the first time, the key role of SiC surface termination on platelet activation. This dependency is in good agreement with the results of our in vitro analysis and points out the prominence of cellular anisotropy. We anticipate that our experimental findings bridge the surface properties to the cellular activities, and therefore, pave the way for tailoring advanced hemocompatible surfaces., (© 2023 The Authors. Journal of Biomedical Materials Research Part A published by Wiley Periodicals LLC.)

Ferritic ODS steel elemental powder compositions with various Zr content (0.3-1.0 wt.%), ground in a Pulverisette 6 planetary ball mill, were extensively studied by X-ray diffraction line profile analysis, microscopic observations, microhardness testing and particle size measurements. A characteristic three-stage process of flattening the soft powders, formation of convoluted lamellae and, finally, formation of nanocrystalline grains was observed. In order to quantify the microstructural properties, expressed mainly in terms of crystallite size and dislocation density, a methodology for detailed and accurate microstructure analysis of nanosized and severely deformed materials was proposed by the Whole Powder Pattern Modelling (WPPM) approach. In the case of the proposed ODS alloy composition, the overlapping of Fe and Cr Bragg reflections makes the microstructure analysis certainly more complicated. The results showed that the microstructure of powders evolved towards the nanocrystalline state consisting of fine (diameter of ~15 nm) and narrowly dispersed domains, with extensive dislocation density exceeding 1016 m -2 .

Additive manufacturing (AM) has seen remarkable development in recent years due to relatively high efficiency of the process. Cold spraying (CS) is a particular method of AM, in which titanium and titanium alloy powders are used. CS is a very competitive technology enabling the deposition of coatings, repairing machine parts, and manufacturing new components. For specific applications, the surface of cold-sprayed materials may require further processing. This paper reports an attempt to employ laser surface treatment (LST) of cold-sprayed coatings on an aluminium alloy substrate. The influence of laser beam interaction time on the coatings' properties was analysed. The microstructure was investigated and observed employing scanning electron microscopy (SEM). To evaluate residual stress after CS and LST, the sin 2 ψ technique was used. Investigations were also performed on Vickers hardness, contact angle, and surface roughness. Significant changes in the surface morphology of the coatings and elevated residual stress levels dependent on the laser beam interaction time were observed. Increased Vickers hardness was recorded for titanium alloy Ti6Al4V. LST also led to increased surface hydrophilicity of the modified materials Ti and Ti6Al4V.

Objective: Zirconia is commonly used for manufacturing of dental implants thanks to its excellent mechanical, biological and aesthetic properties. However, its bioinertness inhibits bonding with the surrounding hard tissue and other surface interactions. In our study, we present a method for multifunctionalization of zirconia surface to improve its osseointegration and to minimize the infection risks., Methods: For this reason, we introduced antibacterial and bioactive properties to zirconia surfaces by calcium phosphate biomimetic coating. The samples were incubated in vials in horizontal and vertical position in concentrated simulated body fluid (SBF) containing 0.1, 0.5, and 3 g/L of silver nanoparticles (Ag-NPs) and then were tested for their structure, surface properties, cytocompatibility and antibacterial properties., Results and Significance: The results demonstrated that our method is suitable to introduce Ag-NPs at different concentrations into the calcium phosphate layer, i.e. from 0.05-26.6 atom% as shown by EDX. According to the results of CFU-assay these coatings exhibited antibacterial properties against S. aureus and E. coli in correlation with the concentration of Ag-NP. The potential cytotoxicity of the coated samples was determined by AlamarBlue® assay and live/dead staining of MG63 osteoblast-like cells in direct contact and by testing the extracts from the materials. Only samples containing 0.05 atom% Ag-NPs, i.e. incubated in vertical position at SBF with 0.01 g/L Ag-NPs, were found cytocompatible in direct contact with MG63 cells. On the contrary in the indirect tests, the extracts from all the materials were found cytocompatible. This method could allow developing the completely new material group, exhibiting not only one but several biological properties, which can improve osseointegration and minimize infection risks., (Copyright © 2020 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.)

The anticoagulation treatment of cardiovascular patients, which is mandatory after implantation of heart valves or stents, has significantly adverse effects on life quality. This treatment can be reduced or even circumvented by developing novel antithrombogenic surfaces of blood-contacting implants. Thus, we aim to discover materials exhibiting outstanding hemocompatibility compared to other available synthetic materials. We present promising surficial characteristics of single crystalline alumina in terms of platelet activation inhibition. In order to elucidate the relation between its crystallographic properties including the plane orientation and blood cell behavior, we examined endothelialization, cytocompatibility, and platelet activation at the blood-alumina interfaces in a controlled experimental setup. We observed that the cell response is highly sensitive to the plane orientation and differs significantly for (0001) and (11-20) planes of Al 2 O 3 . Our results reveal for the first time the dependence of platelet activation on crystallographic orientation, which is assumed to be a critical condition controlling the thrombogenicity. Additionally, we used an endothelial cell monolayer as an internal control since endothelial cells have an impact on vessel integrity and implant acceptance. We successfully demonstrate that Al 2 O 3 (11-20) exhibits enhanced hemocompatibility in contrast to Al 2 O 3 (0001) and is comparable to the physiological endothelial monolayer in vitro .

We report a study on a hybrid mode-locked fiber laser with two saturable absorbers: slow and fast, integrated in a single device. Amorphous antimony telluride (Sb(2)Te(3)) layer was deposited on side-polished fiber to form the slow saturable absorber due to the third order nonlinear susceptibility of Sb(2)Te(3). Additionally, an unsymmetrical design of the device causes polarization-dependent losses and together with polarization controller allows to use a nonlinear polarization evolution to form the artificial fast saturable absorber. Sub-200 fs soliton pulses with 0.27 nJ of pulse energy were generated in the hybrid mode-locked Er-doped fiber laser. Differences in the dynamics of mode-locked laser are further investigated with the use of slow and fast saturable absorbers solely, and compared with the hybrid device. Joint operation of two saturable absorbers enhances the laser performance and stability. The conducted experiments allowed to define roles of each mechanism on the pulse shaping in the laser cavity.