Search

High specific detectivity (D*) is one of the key performance metrics for near‐infrared (NIR) organic photodetectors (OPDs), which however is always limited by the high dark current density (Jd). Herein, high‐performance NIR‐OPDs with ultralow Jd are successfully achieved by developing new conjugated pyrrolic polysquaraines as photoactive materials. By changing the linkage sites of the carbazole bridge, two low‐bandgap pyrrolic polysquaraines, i.e., PSQ‐3,6‐Cz and PSQ‐2,7‐Cz, are prepared via a facile synthetic route, both showing strong absorption in the visible and NIR region (600–1000 nm), respectable hole mobility, and enhanced compatibility with the PC61BM acceptor. The fabricated polysquaraine‐based NIR‐OPDs deliver impressive Jd values as low as ≈2.0 × 10−11 A cm−2 in a photovoltaic mode, which to the best of the knowledge is among the lowest values for NIR‐OPDs so far, and thus enables a high shot‐noise‐limited specific detectivity (Dsh*) over 1013 Jones in 650–950 nm. With a more accurate noise spectral current measurement, the PSQ‐2,7‐Cz‐based OPDs show lower noise currents and better detection performance than the PSQ‐3,6‐Cz‐based OPDs, which is attributed to the lower energetic disorder degree and fewer traps of the former, both resulting in suppressed trap‐assisted recombination. [ABSTRACT FROM AUTHOR]

Squaraine dyes (SQs) are an important class of polymethine dyes with a unique reasonable‐stabilized zwitterionic structure, in which electrons are highly delocalized over the conjugated bridge. These dyes can not only be easily synthesized via a condensation, but also exhibit intense absorption and emission in the visible and near‐infrared region with excellent photochemical stability, making them attractive material candidates for many photoelectric and biomedical applications. Thus, in this review, after an introduction of SQs, the recent advances of SQs in the photovoltaic field are comprehensively summarized including dye‐sensitized solar cells, organic solar cells, and perovskite solar cells. Then, the important advances in the use of SQs as the biosensors, biological imaging, and photodynamic/photothermal therapy reagents in the biomedical field are also discussed. Finally, a summary and outlook will be provided with some new perspectives for the future design of SQs. [ABSTRACT FROM AUTHOR]

Based on the results of the test among the joint roughness coefficient (JRC) of rock fracture, mechanical aperture, and hydraulic aperture proposed by Barton, this paper deduces and proposes a permeability coefficient formula of single fracture stress-seepage coupling considering microroughness by the introduction of effect variables considering the microparticle size and structural morphology of facture surface. Quasi-sandstone fracture of different particle size is made by the laboratory test, and the respective modification is made on the coupled shear-seepage test system of JAW-600 rock. Under this condition, the laboratory test of stress-seepage coupling of fracture of different particle size is carried out. The test results show that, for the different particle-sized fracture surface of the same JRC, the permeability coefficient is different, which means the smaller particle size, the smaller permeability coefficient, and the larger particle size, the larger permeability coefficient; with the increase of cranny hydraulic pressure, the permeability coefficient increases exponentially, and under the same cranny hydraulic pressure, there is relation of power function between the permeability coefficient and normal stress. Meanwhile, according to the theoretical formula, the microroughness coefficient of the fractures with different particle size is obtained by the calculation, and its accuracy and validity are verified by experiments. The theoretical verification values are in good agreement with the measured values. [ABSTRACT FROM AUTHOR]

The grouting technique is an important method in underground engineering that prevents water seepage and reinforces fractured rock mass. In this research, ultrafine cement-based grouting material, including ultrafine cement (UC), ultrafine fly ash (UFA), polycarboxylate superplasticizer (SP), colloidal nanosilica (CNS), sodium sulfate solution (SS) and water, was developed. The flow time, viscosity, bleeding, setting time and uniaxial compressive strength of the UC-based slurry were measured by orthogonal experiments, and the optimal mix proportion of the UC-based slurry was obtained based on the Taguchi-Grey relational analysis method. Microstructure analysis of the UC-based slurry was conducted using scanning electron microscopy (SEM) and mercury intrusion porosimetry (MIP) tests. The results showed that the Bingham model could provide a satisfactory description of the rheological properties of the UC-based slurry. The addition of CNS and SS could promote the hydration of the UC-based slurry and improve the microstructure of the hardened slurry, thereby increasing the strength of the hardened slurry. The optimum ratio for the UC-based slurry was water/solid (W/S) ratio of 1.0, and the contents of UFA, SP, CNS and SS by mass of UC were 40%, 0.2%, 4% and 4%, respectively. [ABSTRACT FROM AUTHOR]

Two challenges remain for organic thermoresponsive materials; one is to develop high-performance red-emissive thermoresponsive materials, while another is to simultaneously achieve high contrast ratio (CR), fast and reversible thermoresponse in a single element. Herein, we not only develop a new deep-red emissive squaraine-based AIEgen (TPE-SQ12) based on a pyrylium end group, which is suitable for fabricating high-performance thermoresponsive materials, but also show an effective approach to improve both CR (∼ten times increase) and response time (less than 3 seconds), that is, molecularly dispersing AIEgen into an elastomer, attributed to the significantly expanded free volume of elastomer upon increasing the temperature that can activate the AIEgen intramolecular movements more pronouncedly. Double encryption and temperature mapping systems have been separately established by using our designed elastomer/TPE-SQ12 film, showing the great potential for anti-counterfeiting and temperature sensing. Finally, white emission is further achieved by co-doping TPE-SQ12 with cyan dye into elastomer, which enables fluorescent thermochromism for improving the temperature mapping ability., (© 2022 Wiley-VCH GmbH.)