Search

On the basis of an analysis of the ITER L-mode energy confinement database, two new scaling expressions for tokamak L-mode energy confinement are proposed, namely a power law scaling and an offset-linear scaling. The analysis indicates that the present multiplicity of scaling expressions for the energy confinement time TE in tokamaks (Goldston, Kaye, Odajima-Shimomura, Rebut-Lallia, etc.) is due both to the lack of variation of a key parameter combination in the database, fs = 0.32 R a^.75 k^ 5 ~ A a^.25 k^.5, and to variations in the dependence of rE on the physical parameters among the different tokamaks in the database. By combining multiples of fs and another factor, fq = 1.56 a^2 kB/R Ip = qeng/3.2, which partially reflects the tokamak to tokamak variation of the dependence of TE on q and therefore implicitly the dependence of TE on Ip and n,., the two proposed confinement scaling expressions can be transformed to forms very close to most of the common scaling expressions. To reduce the multiplicity of the scalings for energy confinement, the database must be improved by adding new data with significant variations in fs, and the physical reasons for the tokamak to tokamak variation of some of the dependences of the energy confinement time on tokamak parameters must be clarified

To visualize the topography of thin oxide films during growth, thereby enabling to study its growth behavior quasi real-time, we have designed and integrated an atomic force microscope (AFM) in a pulsed laser deposition (PLD) vacuum setup. The AFM scanner and PLD target are integrated in a single support frame, combined with a fast sample transfer method, such that in-situ microscopy can be utilized after subsequent deposition pulses. The in-situ microscope can be operated from room temperature (RT) up to 700$^\circ$C and at (process) pressures ranging from the vacuum base pressure of 10$^{-6}$ mbar up to 1 mbar, typical PLD conditions for the growth of oxide films. The performance of this instrument is demonstrated by resolving unit cell height surface steps and surface topography under typical oxide PLD growth conditions., Comment: 8 pages, 8 figures

It is planned to use atomic processes to spread out most of the heating power over the first wall and side walls to reduce the heat loads on the plasma facing components in ITER to ~ 50 MW. Calculations indicate that there will be 100 MW in bremstrahlung radiation from the plasma center, 50 MW of radiation from the plasma edge inside the separatrix and 100 MW of radiation from the scrape-off layer and divertor plasma, leaving 50 MW of power to be deposited on the divertor plates. The radiation losses are enhanced by the injection of impurities such as Neon or Argon at acceptably low levels (~0.1 % Argon, etc.), Comment: Preprint for the Plasma Edge Theory Conference, Monterey, Dec.4-6, 1995, 5 pages, gzipped postscript

An effective radiative divertor maximizes the utilization of atomic processes to spread out the energy deposition to the divertor chamber walls and to reduce the peak heat flux. Because the mixture of neutral atoms and ions in the divertor can be optically thick to a portion of radiated power, it is necessary to accurately model the magnitude and distribution of line radiation in this complex region. To assess their importance we calculate the effects of radiation transport using CRETIN, a multi-dimensional, non-local thermodynamic equilibrium simulation code that includes the atomic kinetics and radiative transport processes necessary to model the complex environment of a radiative divertor. We also include neutral transport to model radiation from recycling neutral atoms. This paper presents a case study of a high-recycling radiative divertor with a typical large neutral pressure at the divertor plate to estimate the impact of H line radiation on the overall power balance in the divertor region with consideration for line opacities and atomic kinetics., Comment: Preprint for the 11th International Conference on Plasma Surface Interactions in Mito, Japan (1994), uuencoded and gzipped postscript with 3 figures, 15 pages

To characterize the conditions required to reach advanced divertor regimes, a one-dimensional computational model has been developed based on a coordinate transformation to incorporate two-dimensional effects. This model includes transport of ions, two species each of atoms and molecules, momentum, and ion and electron energy both within and across the flux surfaces. Impurity radiation is calculated using a coronal equilibrium model which includes the effects of charge-exchange recombination. Numerical results indicate that impurity radiation acts to facilitate plasma detachment and enhances the power lost from the divertor channel in escaping neutral atoms by cooling the electrons and suppressing ionization. As divertor particle densities increase, cold and thermal molecules become increasingly important in cooling the plasma, with molecular densities dominating electron and atomic densities under some conditions., Comment: Preprint for the 11th International Conference on Plasma Surface Interactions in Mito, Japan (1994), uuencoded and gzipped postscript with 5 figures, 14 pages

The role of impurity radiation in the reduction of heat loads on divertor plates in present experiments such as DIII-D, JET, JT-60, ASDEX, and Alcator C-Mod, and in planned experiments such as ITER and TPX places a new degree of importance on the accuracy of impurity radiation emission rates for electron temperatures below 250 eV for ITER and below 150 eV for present experiments. We have calculated the radiated power loss using a collisional radiative model for Be, B, C, Ne and Ar using a multiple configuration interaction model which includes density dependent effects, as well as a very detailed treatment of the energy levels and meta-stable levels. The "collisional radiative" effects are very important for Be at temperatures below 10 eV. The same effects are present for higher Z impurities, but not as strongly. For some of the lower Z elements, the new rates are about a factor of two lower than those from a widely used, simpler average-ion package (ADPAK) developed for high Z ions and for higher temperatures. Following the approach of Lengyel for the case where electron heat conduction is the dominant mechanism for heat transport along field lines, our analysis indicates that significant enhancements of the radiation losses above collisional radiative model rates due to such effects as rapid recycling and charge exchange recombination will be necessary for impurity radiation to reduce the peak heat loads on divertor plates for high heat flux experiments such as ITER., Comment: Preprint for the 11th PSI meeting, gzipped postscript with 11 figures, 14 pages

Reduction of the peak heat loads on the plasma facing components is essential for the success of the next generation of high fusion power tokamaks such as the International Thermonuclear Experimental Reactor (ITER) 1 . Many present concepts for accomplishing this involve the use of atomic processes to transfer the heat from the plasma to the main chamber and divertor chamber walls and much of the experimental and theoretical physics research in the fusion program is directed toward this issue. The results of these experiments and calculations are the result of a complex interplay of many processes. In order to identify the key features of these experiments and calculations and the relative role of the primary atomic processes, simple quasi-analytic models and the latest atomic physics rate coefficients and cross sections have been used to assess the relative roles of central radiation losses through bremsstrahlung, impurity radiation losses from the plasma edge, charge exchange and hydrogen radiation losses from the scrape-off layer and divertor plasma and impurity radiation losses from the divertor plasma. This anaysis indicates that bremsstrahlung from the plasma center and impurity radiation from the plasma edge and divertor plasma can each play a significant role in reducing the power to the divertor plates, and identifies many of the factors which determine the relative role of each process. For instance, for radiation losses in the divertor to be large enough to radiate the power in the divertor for high power experiments, a neutral fraction of 10-3 to 10-2 and an impurity recycling rate of netrecycle of ~ 10^16 s m^-3 will be required in the divertor., Comment: Preprint for the 1994 APSDPP meeting, uuencoded and gzipped postscript with 22 figures, 40 pages.

Present divertor concepts for next step experiments such ITER and TPX rely upon impurity and hydrogen radiation to transfer the energy from the edge plasma to the main chamber and divertor chamber walls. The efficiency of these processes depends strongly on the heat flux, the impurity species, and the connection length. Using a database for impurity radiation rates constructed from the ADPAK code package, we have developed criteria for the required impurity fraction, impurity species, connection length and electron temperature and density at the mid-plane. Consistent with previous work, we find that the impurity radiation from coronal equilibrium rates is, in general, not adequate to exhaust the highest expected heating powers in present and future experiments. As suggested by others, we examine the effects of enhancing the radiation rates with charge exchange recombination and impurity recycling, and develop criteria for the minimum neutral fraction and impurity recycling rate that is required to exhaust a specified power. We also use this criteria to find the optimum impurity for divertor power exhaust., Comment: Preprint for the 11th PSI meeting, Adobe pdf with 14 figures, 15 pages

The most promising concepts for power and particle control in tokamaks and other fusion experiments rely upon atomic processes to transfer the power and momentum from the edge plasma to the plasma chamber walls. This places a new emphasis on processes at low temperatures (1-200 eV) and high densities (10^20-10^22 m^-3). The most important atomic processes are impurity and hydrogen radiation, ionization, excitation, recombination, charge exchange, radiation transport, molecular collisions, and elastic scattering of atoms, molecules and ions. Important new developments have occurred in each of these areas. The best available data for these processes and an assessment of their role in plasma wall interactions are summarized, and the major areas where improved data are needed are reviewed., Comment: Preprint for the 11th PSI meeting, postscript with 22 figures, 40 pages