Search

The electronic properties of the indium oxide (In2O3) material make it suitable for solar cells, sensors and electrocatalysts. Structural, electronic and thermal properties of two bulk In2O3 polytypes with low energy are studied and investigated using density functional theory. From structural optimization based on total energy calculations, lattice and positional parameters have been established. The electronic properties were computed by HSE-06. The thermal properties including heat capacity and entropy were obtained. Evaluated the mechanical stability by computing the single-crystal elastic constants. Calculated the Poisson’s ratio and Bulk/Shear modulus which are above the critical value, implying that they are ductile material.

The rapid electrification of our society and the transition towards a larger share of intermittent renewable energy sources in our electricity grids will dramatically increase the demand for cheap energy storage. Sodium ion batteries (SIBs) show a lot of promise to provide the required stationary storage at the grid level at low cost owing to the natural abundance and geographical availability of sodium. In addition, alkali-rich cathode materials exhibiting anionic redox contributions have garnered much attention over the past decade as a strategy to increase the specific capacity. In this work, we investigate for the first time the sodium-rich compound Na5FeO4 as a potential low-cost, environment-friendly cathode for sodium ion batteries from first principles using density functional theory. We investigate three low-energy polymorphs related to the antifluorite structure, verify their dynamical and mechanical stabilities, and show that they exhibit promising ion diffusive properties. As alkali-rich cathode materials are prone to oxygen loss during cycling, we investigate cycling stability with respect to phase transformations and oxygen loss and identify in particular one promising cycling interval that can reversibly shuttle 1.5 Na+ per formula unit between Na5FeO4 and Na3.5FeO4 with a gravimetric energy density exceeding 360 W h kg−1. Investigations into possible redox mechanisms reveal that the charge compensation occurs simultaneously on Fe- and O-atoms in FeO4-tetrahedra, which suggests that Na5FeO4, if realised experimentally as a cathode material, would join the family of combined cationic/anionic redox compounds.

We have investigated the pressure (P) effect on structural (up to 10 GPa), transport [R(T): up to 10 GPa], and magnetic [(M(T): up to 1 GPa)] properties and analyzed the flux pinning mechanism of the Fe0.99Mn0.01Se0.5Te0.5 superconductor. The maximum superconducting transition temperature (T c) of 22 K with the P coefficient of T c dT c/dP = +2.6 K/GPa up to 3 GPa (dT c/dP = -3.6 K/GPa, 3 ≤ P ≥ 9 GPa) was evidenced from R(T) measurements. The high-pressure diffraction and density functional theory (DFT) calculations reveal structural phase transformation from tetragonal to hexagonal at 5.9 GPa, and a remarkable change in the unit cell volume is observed at ∼3 GPa where the T c starts to decrease, which may be due to the reduction of charge carriers, as evidenced by a reduction in the density of states (DOS) close to the Fermi level. At higher pressures of 7.7 GPa ≤ P ≥ 10.2 GPa, a mixed phase (tetragonal + hexagonal phase) is observed, and the T c completely vanishes at 9 GPa. A significant enhancement in the critical current density (J C) is observed due to the increase of pinning centers induced by external pressure. The field dependence of the critical current density under pressure shows a crossover from the δl pinning mechanism (at 0 GPa) to the δT c pinning mechanism (at 1.2 GPa). The field dependence of the pinning force at ambient condition and under pressure reveals the dense point pinning mechanism of Fe0.99Mn0.01Se0.5Te0.5. Moreover, both upper critical field (H C2) and J C are enhanced significantly by the application of an external P and change over to a high P phase (hexagonal ∼5.9 GPa) faster than a Fe0.99Ni0.01Se0.5Te0.5 (7.7 GPa) superconductor.

We report high-pressure structural studies (52 GPa) at room temperature combined with magnetic [(M(T):1GPa] and electrical resistivity [(ρ(T):0-21GPa)] measurements down to 2 K on Fe0.99Ni0.01Se0.5Te0.5 superconductor using designer diamond anvils (D-DAC) pressure cell. The M(T) data show huge enhancement of superconducting transition temperature (Tc) from 8.62 to 14.8 K (1 GPa) and ρ(T) reveal maximum enhancement of Tc ~ 30.5 K at 3 GPa (dTc/dP = ~ 7.19 K/GPa) followed by moderate decrease of Tc up to 19 K at 7.5 GPa, and further increasing pressure Tc gets vanished at 10.6 GPa. The reduction of Tc due to the occurrence of structural transition that is likely associated with possible reduction of charge carriers in the density of states in Fermi surface. The high-pressure XRD measurement shows tetragonal phase exists up to 7 GPa, followed by mixed phase which is visible between 7.5 GPa and 14.5 GPa. The structural transformation occurs at 15 GPa from tetragonal (P4/nmm) to NiAs -type hexagonal phase (P63/mmc) and it is stable up to 52 GPa, confirmed from the equation of state (EOS) and it can be correlated with variation of Tc under pressure for Fe0.99Ni0.01Se0.5Te0.5 chalcogenide superconductors.

Silicoaluminophosphates (SAPOs) are a special class of zeolites that, due to their acidic and shape-selective properties, play a major role in ion exchange and separation processes and in crude oil cracking. SAPO-37 has the faujasite (FAU) topology same as zeolites X and Y, which are involved in more than 40% of the total crude oil conversion worldwide. A critical parameter that promotes detrimental structural transformations in SAPOs during real-life applications is the presence of humidity. In this study, we employ a multidisciplinary approach combining in situ synchrotron radiation powder X-ray diffraction (SR-PXRD), water adsorption, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), and density functional theory (DFT) calculations to describe the mechanism and reveal the reasons why SAPO-37 collapses upon contact with humidity below 345 K. SR-PXRD revealed that the sodalite (SOD) cages (subunits of the FAU structure) have the strongest affinity to water during hydration below 345 K. Furthermore, below 345 K, the faujasite framework takes up an order of magnitude more water molecules than at temperatures above 345 K. DRIFTS confirmed the presence of Si−OH and P−OH surface structural defects that act as hydration centers, accelerating the loss of a long-range order. Finally, DFT calculations showed that the enthalpy of water adsorption in the sodalite cage and the faujasite supercage is −212 and −13 kJ/mol, respectively. The results presented in this work are highly topical for understanding the effect of water on the frameworks of the SAPO microporous catalysts family. The notorious instability of SAPO-37 is the result of the accumulative contribution of topological, physical, and chemical effects, leading to an array of rapidly evolving cascading effects. Our work shows how advancements in SR-PXRD methodology and hardware give new insight into highly dynamic features previously difficult to observe. In addition, this work introduces the conceptual insight that nonhomogeneous sorption of molecular species will induce dynamic features with dramatic consequences at both molecular and atomic levels. This is a highly impactful factor opening research paths for further work within catalysis, porous material design and chemistry, and sorption reactions and processes.

The rapid electrification of our society and the transition towards a larger share of intermittent renewable energy sources in our electricity grids will dramatically increase the demand for cheap energy storage. Sodium ion batteries (SIBs) show a lot of promise to provide the required stationary storage at the grid level at low cost owing to the natural abundance and geographical availability of sodium. In addition, alkali-rich cathode materials exhibiting anionic redox contributions have garnered much attention over the past decade as a strategy to increase the specific capacity. In this work, we investigate for the first time the sodium-rich compound Na

High entropy alloy (HEA) films of CrFeCoNiCu were deposited by sputtering. Their structure was characterized and their electric transport properties were studied by temperature-dependent Hall and Seebeck measurements. The HEA films show a solid solution with an fcc structure. The residual electrical resistivity of the films is around 130 μΩ cm, which is higher than the Mott limit for a metal while the temperature dependence of the resistivity above 30 K is metal-like but with a small temperature coefficient of resistivity (2 ppm/K). The dominant scattering mechanism of charge carriers is alloy scattering due to chemical disorder in the HEA. The Hall coefficient is positive while the Seebeck coefficient is negative. This is interpreted as arising from an electronic structure where the Fermi level passes through band states having both holes and electrons as indicated by band structure calculations. Below 30 K, the conduction is discussed in terms of weak localization and Kondo effects. The HEA structure appears stable for annealing in vacuum, while annealing in an oxygen-containing atmosphere causes the surface to oxidize and grow a Cr-rich oxide on the surface. This is then accompanied by demixing of the HEA solid solution and a decrease in the effective resistance of the film.

We have used operando 5D synchrotron total scattering computed tomography (TSCT) to understand the cycling and possible long term deactivation mechanisms of the lithium-ion battery anode bismuth vanadate. This anode material functions via a combined conversion/alloying mechanism in which nanocrystals of lithium–bismuth alloy are protected by an amorphous matrix of lithium vanadate. This composite is formed in situ during the first lithiation of the anode. The operando TSCT data were analyzed and mapped using both pair distribution function and Rietveld methods. We can follow the lithium–bismuth alloying reaction at all stages, gaining real structural insight including variations in nanoparticle sizes, lattice parameters and bond lengths, even when the material is completely amorphous. We also observe for the first time structural changes related to the cycling of lithium ions in the lithium vanadate matrix, which displays no interactions beyond the first shell of V–O bonds. The first 3D operando mapping of the distribution of different materials in an amorphous anode reveals a decline in coverage caused by either agglomeration or partial dissolution of the active material, hinting at the mechanism of long term deactivation. The observations from the operando experiment are backed up by post mortem transmission electron microscope (TEM) studies and theoretical calculations to provide a complete picture of an exceptionally complex cycling mechanism across a range of length scales.

We report the effect of high pressure on the superconducting, vortex pinning, and structural properties of a polycrystalline non-centrosymmetric superconductor Re6Hf. The superconducting transition temperature, Tc, reveals a modest decrease as pressure P increases with a slope -0.046 K/GPa (-0.065 K/GPa) estimated from resistivity measurements up to 8 GPa (magnetization measurement ~ 1.1 GPa). Structural analysis up to ~18 GPa reveals monotonic decreases of lattice constant without undergoing any structural transition and a high value of bulk modulus B0= 333.63 GPa, indicating the stability of the structure. Furthermore, the upper critical field and lower critical field at absolute temperature (Hc2(0) & Hc1(0)) decreases slightly from the ambient pressure value as pressure increases up to 2.5 GPa. In addition, up to P ~ 2.5 GPa using thermally activated flux flow of vortices revealed a double linearity field dependence of activation energy of vortices, confirming the coexistence of single and collective pinning vortex states. Moreover, analysis of critical current density using the collective pinning theory showed the transformation of {\delta}Tc to {\delta}l pinning as pressure increases, possibly due to migration of grain boundaries. Besides, the band structure calculations using density functional theory show that density of states decreases modestly with pressure, which may be a possible reason for such a small decrease in Tc by pressure., Comment: 14 pages, 10 figures, Article

Understanding an interrelation between the structure, chemical composition and hydrogenation properties of intermetallic hydrides is crucial for the improvement of their hydrogen storage performance. Ability to form the hydrides and to tune the thermodynamics and kinetics of their interaction with hydrogen is related to their chemical composition. Some features of the metal–hydrogen interactions remain however poorly studied, including chemistry of Sc-containing hydrides. ZrNiAl-type ScNiSn-based intermetallic hydride has been probed in the present work using a broad range of experimental techniques including Synchrotron and Neutron Powder Diffraction, $^{119}$Sn Möessbauer Spectroscopy, hydrogenation at pressures reaching several kbar H$_2$ and hydrogen Thermal Desorption Spectroscopy studies. Computational DFT calculations have been furthermore performed. This allowed to establish the mechanism of the phase-structural transformation and electronic structure changes causing a unique contraction of the metal lattice of intermetallic alloy and the formation of the ...H-Ni-H-Ni… chains in the structure with H atoms carrying a partial negative charge. Such hydrogen absorption accompanied by a formation of a covalent Ni-H bonding and causing an unusual behavior contracts to the conventionally observed bonding mechanism of hydrogen in metals as based on the metallic bonding frequently accompanied by a jumping diffusion movement of the inserted H atoms – in contrast to the directional Metal-Hydrogen bonding observed in the present work. At high applied pressures ScNiSnH$_{0.83}$ orthorhombic TiNiSi type hydride is formed with H atoms filling Sc$_3$Ni tetrahedra. Finally, this study shows that scandium closely resembles the behavior of the heavy rare earth metal holmium.

Correction for ‘5D total scattering computed tomography reveals the full reaction mechanism of a bismuth vanadate lithium ion battery anode’ by Jonas Sottmann et al., Phys. Chem. Chem. Phys., 2022, 24, 27075–27085, https://doi.org/10.1039/D2CP03892G.

Tin dioxide (SnO

Based on the same rocking-chair principle as rechargeable Li-ion batteries, Na-ion batteries are promising solutions for energy storage benefiting from low-cost materials comprised of abundant elements. However, despite the mechanistic similarities, Na-ion batteries require a different set of active materials than Li-ion batteries. Bismuth molybdate (Bi

We have studied the effect of hydrostatic pressure on the superconducting and normal state properties of the non-centrosymmetric superconductor Re5.5Ta using magnetotransport, magnetization, and band structure studies. The superconducting transition temperature ( T c ) reveals a modest decrease of ∼0.52 K as the external pressure is raised to 8 GPa. We found the Maki parameter, 1,$?> α M > 1 , both at ambient and high pressures, suggesting the significant role of the Pauli pair breaking effect. Furthermore, the lower critical field was found to decrease with a rate of −1.74 mT GPa−1 as pressure increases to 1.05 GPa. Analysis of the thermally activated flux flow region of ρ T , H using the Arrhenius equation reveals the coexistence of single and collective vortex states. Further analysis of the critical current density indicates that the surface and volume pinning centers coexist and remain unaffected with varying pressure. Band structure calculations were performed using density functional theory and reveal a large bulk modulus, B 0 ∼ 289 GPa with B 0 ′ ∼ 3.7, suggesting poor compressibility. In addition, we found that the density of states at the Fermi level barely reduces, even at pressures of up to 20 GPa. This is consistent with the experimental observation of robust superconductivity under compression.

Polymorphs are common in nature and can be stabilized by applying external pressure in materials. The pressure and strain can also be induced by the gradually accumulated radiation disorder. However, in semiconductors, the radiation disorder accumulation typically results in the amorphization instead of engaging polymorphism. By studying these phenomena in gallium oxide we found that the amorphization may be prominently suppressed by the monoclinic to orthorhombic phase transition. Utilizing this discovery, a highly oriented single-phase orthorhombic film on the top of the monoclinic gallium oxide substrate was fabricated. Exploring this system, a novel mode of the lateral polymorphic regrowth, not previously observed in solids, was detected. In combination, these data envisage a new direction of research on polymorphs in Ga_{2}O_{3} and, potentially, for similar polymorphic families in other materials.

In this work, we examine the distribution of Na+ ions in the interlayer of the super-ionic conductor Na2Zn2TeO6 by means of atomistic first-principle modeling based on density functional theory. Th...

The LiCl salt flux method is an established aid in oxyhydride synthesis. By operating the flux below its melting point, we have obtained phase pure Nd2LiHO3 for the first time. Further, the suitability of the flux method is shown to be dictated by a delicate balance between the thermal stability of the oxyhydride in question and the ionic mobility of the reactants.

Bi2(MoO4)3 has been evaluated as an interesting anode material for application in lithium-ion batteries (LIBs). When cycled in the voltage window of 0.01–2.50 V a specific charge capacity of more than 800 mA h g−1 is retained after 50 cycles. According to operando synchrotron X-ray diffraction (XRD) the long-range order is lost during the initial lithiation. Direct insight into the electronic changes during cycling is obtained from operando Bi L3- and Mo K-edge X-ray absorption near edge spectroscopy (XANES) data collected during the first 1.5 cycles. A redox pair with anodic reactions at 0.97 V and cathodic reactions at 0.59 V is ascribed to alloying of bismuth: 3Li + Bi ↔ 2Li + LiBi ↔ Li3Bi. Likewise, reactions are ascribed to redox processes of Mo. Notably, the use of a cycling range limited to 2.00 V does not allow for a complete reoxidation of Mo, which in turn limits the reversibility of the Mo redox reactions.

Hydrostatic pressure response of $\mathrm{LaAu}{\mathrm{Sb}}_{2}$ charge density wave (CDW) system is investigated using electrical transport, x-ray diffraction (XRD), and density-functional theory (DFT). Resistivity data at ambient pressure evidence a clear CDW transition at 83 K. X-ray diffraction at ambient pressure reveals that in plane and out of plane axes show opposite behavior with decreasing temperature, in particular, out of plane $c$ axis develops a distinct change at \ensuremath{\sim}250 K, much above the observed CDW transition at 83 K. The CDW transition shifts to low temperature with increasing pressure. Our resistivity data indicate a complete suppression of the CDW transition at \ensuremath{\sim}3.6 GPa. High-pressure XRD revealed a change from the linear trend for the out of plane ($c$) and the in plane ($a$) lattice parameters for pressure above 3.8 GPa. With compression, DFT indicated an anomaly in the c/a ratio around 8 GPa. The calculated electronic structure also indicated minor changes in the band structure in this pressure range. In addition, high-pressure DFT structural investigations reveal the $\mathrm{LaAu}{\mathrm{Sb}}_{2}$ system to be stable up to pressures as high as 150 GPa.

This study investigates the potential of utilizing multifunctional nanostructured materials for the efficient light trapping and electron transport in solar cells by combining titanium dioxide (TiO 2) rods and nanoparticles. A simple solvothermal method was adopted for the synthesis of coupled morphology adopting the desired precursor with the constant concentration and temperature. The reaction duration (12, 24, 36 and 48 h) was varied and the materials resultant physical, optical and structural characteristics were elucidated to determine the nature of the prepared material. The crystallographic phase of the synthesized samples was determined with XRD and Raman analysis. From the experimental data it is hypothesized that the surface plane of anatase (105) is involved in the deformation of the structure and the formation of the rutile phase. To further investigate on the formation of mixed phase in the prepared sample a computation study was performed using density functional theory coupled to the Hubbard U correction (DFT + U) as a function of volume in both the anatase and rutile phases. The relative stability of the O–Ti–O networks is explored starting from ultrathin materials for four different sizes, of anatase and rutile nanorods separately. Finally, the synthesized TiO 2 materials were used to prepare screen printed dye sensitized solar cell (DSSC) devices and their respective properties were quantified.

Hydrogen produced from water using photocatalysts driven by sunlight is a sustainable way to overcome the intermittency issues of solar power and provide a green alternative to fossil fuels. TiO2 has been used as a photocatalyst since the 1970s due to its low cost, earth abundance, and stability. There has been a wide range of research activities in order to enhance the use of TiO2 as a photocatalyst using dopants, modifying the surface, or depositing noble metals. However, the issues such as wide bandgap, high electron-hole recombination time, and a large overpotential for the hydrogen evolution reaction (HER) persist as a challenge. Here, we review state-of-the-art experimental and theoretical research on TiO2 based photocatalysts and identify challenges that have to be focused on to drive the field further. We conclude with a discussion of four challenges for TiO2 photocatalysts—non-standardized presentation of results, bandgap in the ultraviolet (UV) region, lack of collaboration between experimental and theoretical work, and lack of large/small scale production facilities. We also highlight the importance of combining computational modeling with experimental work to make further advances in this exciting field.

The vibrational properties of several High Entropy Alloy (HEA) based metal hydrides are investigated by inelastic neutron scattering (INS). HEAs have recently emerged as a new type of materials with a wide range of intriguing properties and potential applications such as hydrogen storage. The special properties of HEAs are believed to originate from the disordered lattice and internal strain that is introduced from the differences in atomic radii. This makes HEA hydrides provide an intriguing situation for the local H coordination, of several different transition metals. INS spectra were collected on a series of HEA-based metal hydrides starting with TiVNbHx and subsequently adding Zr and Hf to increase the atomic size mismatch. A general feature of the spectra are the optical peaks centered around an energy loss of 150 meV that can be attributed to hydrogen vibrations in a tetrahedral environment. Upon the addition of Zr and Hf, a shoulder appears on the optical peak at lower energy transfers that after comparison with in silico calculated INS spectra is indicative of hydrogen also occupying octahedral sites in the structure.

Hydrogen produced from water using photocatalysts driven by sunlight is a sustainable way to overcome the intermittency issues of solar power and provide a green alternative to fossil fuels. TiO2 has been used as a photocatalyst since the 1970s due to its low cost, earth abundance, and stability. There has been a wide range of research activities in order to enhance the use of TiO2 as a photocatalyst using dopants, modifying the surface, or depositing noble metals. However, the issues such as wide bandgap, high electron-hole recombination time, and a large overpotential for the hydrogen evolution reaction (HER) persist as a challenge. Here, we review state-of-the-art experimental and theoretical research on TiO2 based photocatalysts and identify challenges that have to be focused on to drive the field further. We conclude with a discussion of four challenges for TiO2 photocatalysts—non-standardized presentation of results, bandgap in the ultraviolet (UV) region, lack of collaboration between experimental and theoretical work, and lack of large/small scale production facilities. We also highlight the importance of combining computational modeling with experimental work to make further advances in this exciting field.

Molybdenum disulphide (MoS2) is a rising star among transition-metal dichalcogenides in photovoltaics, diodes, electronic circuits, transistors and as a photocatalyst for hydrogen evolution. A wide range of MoS2 polymorphs with varying electrical, optical and catalytic properties is of interest. However, in-depth studies on the structural stability of the various MoS2 polymorphs are still lacking. For the very first time, 14 different MoS2 polymorphs are proposed in this study and in-depth analysis of these polymorphs are carried out by employing first-principle calculations based on density functional theory (DFT). In order to investigate the feasibility of these polymorphs for practical applications, we employ wide range of analytical methods including band structure, phonon and elastic constant calculations. Three of the polymorphs were shown to be unstable based on the energy volume calculations. Among the remaining eleven polymorphs (1T1, 1T2, 1H, 2T, 2H, 2R1, 2R2, 3Ha, 3Hb, 3R and 4T), we confirm that the 1T1, 1T2, 2R2 and 3R polymorphs are not dynamically stable based on phonon calculations. Recent research suggests that stabilising dopants (e.g. Li) are needed if 1T polymorphs to be synthesised. Our study further shows that the remaining seven polymorphs are both dynamically and mechanically stable, which make them interesting candidates for optoelectronics applications. Due to high electron mobility and a bandgap of 1.95 eV, one of the MoS2 polymorphs (3Hb-MoS2) is proposed to be the most promising candidate for these applications.

Molybdenum disulphide (MoS

The layered oxide Na2Zn2TeO6 is a fast Na+ ion conductor and a suitable candidate for application as a solid-state electrolyte. We present a detailed study on how synthesis temperature and Na-content affect the crystal structure and thus the Na+ ion conductivity of Na2Zn2TeO6. Furthermore, we report for the first time an O′3-type phase for Na2Zn2TeO6. At a synthesis temperature of 900 °C, we obtain a pure P2-type phase, providing peak performance in Na+ ion conductivity. Synthesis temperatures lower than 900 °C produce a series of mixed P2 and O′3-type phases. The O′3 structure can only be obtained as a pure phase by substituting Li on the Zn-sites to increase the Na-content. Thorough analysis of synchrotron data combined with computational modeling indicates that Li enters the Zn sites and, consequently, the amount of Na in the structure increases to balance the charge according to the formula Na2+xZn2–xLixTeO6 (x = 0.2–0.5). Impedance spectroscopy and computational modeling confirm that reducing the amount of the O′3-type phase enhances the Na+ ion mobility.

Using a facile one-pot colloidal method, it is now possible to obtain monodisperse Co1−xRex nanoparticles (NPs), with excellent control of Re stoichiometry for x < 0.15. Re-incorporation in terms of a solid solution stabilizes the β-Mn polymorph relative to the hcp/ccp variants of cobalt. The NPs are thermally stable up to 300 °C, which may make them attractive as model catalysts.

The layered oxide Na2Zn2TeO6 is a fast Na+ ion conductor and a suitable candidate for application as a solid-state electrolyte. We present a detailed study on how synthesis temperature and Na-content affect the crystal structure and thus the Na+ ion conductivity of Na2Zn2TeO6. Furthermore, we report for the first time an O'3-type phase for Na2Zn2TeO6. At a synthesis temperature of 900 °C, we obtain a pure P2-type phase, providing peak performance in Na+ ion conductivity. Synthesis temperatures lower than 900 °C produce a series of mixed P2 and O'3-type phases. The O'3 structure can only be obtained as a pure phase by substituting Li on the Zn-sites to increase the Na-content. Thorough analysis of synchrotron data combined with computational modeling indicates that Li enters the Zn sites and, consequently, the amount of Na in the structure increases to balance the charge according to the formula Na2+xZn2-xLixTeO6 (x = 0.2-0.5). Impedance spectroscopy and computational modeling confirm that reducing the amount of the O'3-type phase enhances the Na+ ion mobility.