Search

Single epitaxial quantum dots (QDs) embedded in nanophotonic geometries are a leading technology for quantum light generation. However, efficiently coupling their emission into a single mode fiber or Gaussian beam often remains challenging. Here, we use direct laser writing (DLW) to address this challenge by fabricating 1 $\mu$m diameter polymer nanowires (PNWs) in-contact-with and perpendicular-to a QD-containing GaAs layer. QD emission is coupled to the PNW's HE$_{11}$ waveguide mode, enhancing collection efficiency into a single-mode fiber. PNW fabrication does not alter the QD device layer, making PNWs well-suited for augmenting preexisting in-plane geometries. We study standalone PNWs and PNWs in conjunction with metallic nanoring devices that have been previously established for increasing extraction of QD emission. We report methods that mitigate standing wave reflections and heat, caused by GaAs's absorption/reflection of the lithography beam, which otherwise prevent PNW fabrication. We observe a factor of $(3.0 \pm 0.7)\times$ improvement in a nanoring system with a PNW compared to the same system without a PNW, in line with numerical results, highlighting the PNW's ability to waveguide QD emission and increase collection efficiency simultaneously. These results demonstrate new DLW functionality in service of quantum emitter photonics that maintains compatibility with existing top-down fabrication approaches., Comment: Comments welcomed

Integrated heaters are a basic ingredient within the photonics toolbox, in particular for microresonator frequency tuning through the thermo-refractive effect. Resonators that are fully embedded in a solid cladding (typically SiO\textsubscript{2}) allow for straightforward lossless integration of heater elements. However, air-clad resonators, which are of great interest for short wavelength dispersion engineering and direct interfacing with atomic/molecular systems, do not usually have similarly low loss and efficient integrated heater integration through standard fabrication. Here, we develop a new approach in which the integrated heater is embedded in SiO$_2$ below the waveguiding layer, enabling more efficient heating and more arbitrary routing of the heater traces than possible in a lateral configuration. We incorporate these buried heaters within a stoichiometric Si$_3$N$_4$ process flow that includes high-temperature ($>$1000~$^\circ$C) annealing. Microring resonators with a 1~THz free spectral range and quality factors near 10$^6$ are demonstrated, and the resonant modes are tuned by nearly 1.5~THz, a 5$\times$ improvement compared to equivalent devices with lateral heaters\greg{.} Finally, we demonstrate broadband dissipative Kerr soliton generation in this platform, and show how the heaters can be utilized to aid in bringing relevant lock frequencies within a detectable range.

Optical parametric oscillation (OPO) is distinguished by its wavelength access, that is, the ability to flexibly generate coherent light at wavelengths that are dramatically different from the pump laser, and in principle bounded solely by energy conservation between the input pump field and the output signal/idler fields. As society adopts advanced tools in quantum information science, metrology, and sensing, microchip OPO may provide an important path for accessing relevant wavelengths. However, a practical source of coherent light should additionally have high conversion efficiency and high output power. Here, we demonstrate a silicon photonics OPO device with unprecedented performance. Our OPO device, based on the third-order ($\chi^{(3)}$) nonlinearity in a silicon nitride microresonator, produces output signal and idler fields widely separated from each other in frequency ($>$150 THz), and exhibits a pump-to-idler conversion efficiency up to 29 $\%$ with a corresponding output idler power of $>$18 mW on-chip. This performance is achieved by suppressing competitive processes and by strongly overcoupling the output light. This methodology can be readily applied to existing silicon photonics platforms with heterogeneously-integrated pump lasers, enabling flexible coherent light generation across a broad range of wavelengths with high output power and efficiency., Comment: Comments welcomed

Being able to combine different materials allows taking advantage of different properties and device engineering that cannot be found or exploited within a single material system. In quantum nano-photonics, one might want to increase the device functionalities by, for instance, combining efficient classical and quantum light emission available in III-V semiconductors, low-loss light propagation accessible in silicon-based materials, fast electro-optical properties of lithium niobate and broadband reflectors and/or buried metallic contacts for local electric field application or electrical injection of emitters. We propose a transfer printing technique based on the removal of arrays of free-standing membranes and their deposition onto a host material using a thermal release adhesive tape-assisted process. This approach is versatile, in that it poses limited restrictions on the transferred and host materials. In particular, we transfer 190 nm-thick GaAs membranes, with dimensions up to about 260$\mu$m x 80$\mu$m, containing InAs quantum dots, onto a gold substrate. We show that the presence of a back reflector combined with the etching of micro-pillars significantly increases the extraction efficiency of quantum light, reaching photon fluxes, from a single quantum dot line, exceeding 8 x 10$^5$ photons per second, which is four times higher than the highest count rates measured, on the same chip, from emitters outside the pillars. Given the versatility and the ease of the process, this technique opens the path to the realisation of hybrid quantum and nano-photonic devices that can combine virtually any material that can be undercut to realise free-standing membranes that are then transferred onto any host substrate, without specific compatibility issues and/or requirements.

To implement quantum light sources based on quantum emitters in applications, it is desirable to improve the extraction efficiency of single photons. In particular controlling the directionality and solid angle of the emission are key parameters, for instance, to couple single photons into optical fibers and send the information encoded in quantum light over long distances, for quantum communication applications. In addition, fundamental studies of the radiative behavior of quantum emitters, including studies of coherence and blinking, benefit from such improved photon collection. Quantum dots grown via Stranski-Krastanov technique have shown to be good candidates for bright, coherent, indistinguishable quantum light emission. However, one of the challenges associated with these quantum light sources arises from the fact that the emission wavelengths can vary from one emitter to the other. To this end, broadband light extractors that do not rely on high-quality factor optical cavities would be desirable, so that no tuning between the quantum dot emission wavelength and the resonator used to increase the light extraction is needed. Here, we show that metallic nano-rings combined with gold back reflectors increase the collection efficiency of single photons and we study the statistics of this effect when quantum dots are spatially randomly distributed within the nano-rings. We show an average increase in the brightness of about a factor 7.5, when comparing emitters within and outside the nano-rings in devices with a gold back reflector, we measure count rates exceeding 7 x 10^6 photons per second and single photon purities as high as 85% +/- 1%. These results are important steps towards the realisation of scalable, broadband, easy to fabricate sources of quantum light for quantum communication applications., Comment: 5 pages, 4 figures

Optical parametric oscillation (OPO) using the third-order nonlinearity ($\chi^{(3)}$) in integrated photonics platforms is an emerging approach for coherent light generation, and has shown great promise in achieving broad spectral coverage with small device footprints and at low pump powers. However, current $\chi^{(3)}$ nanophotonic OPO devices use pump, signal, and idler modes of the same transverse spatial mode family. As a result, such single-mode-family OPO (sOPO) is inherently sensitive in dispersion and can be challenging to scalably fabricate and implement. In this work, we propose to use different families of transverse spatial modes for pump, signal, and idler, which we term as hybrid-mode-family OPO (hOPO). We demonstrate its unprecedented robustness in dispersion versus device geometry, pump frequency, and temperature. Moreover, we show the capability of the hOPO scheme to generate a few milliwatts of output signal power with a power conversion efficiency of approximately 8 $\%$ and without competitive processes. The hOPO scheme is an important counterpoint to existing sOPO approaches, and is particularly promising as a robust method to generate coherent on-chip visible and infrared light sources., Comment: 11 pages, 7 figures

Broad bandwidth and stable microresonator frequency combs are critical for accurate and precise optical frequency measurements in a compact and deployable format. Typically, broad bandwidths (e.g., octave spans) are achieved by tailoring the microresonator's geometric dispersion. However, geometric dispersion engineering alone may be insufficient for sustaining bandwidths well beyond an octave. Here, we introduce the novel concept of synthetic dispersion, in which a second pump laser effectively alters the dispersion landscape to create Kerr soliton microcombs that extend far beyond the anomalous geometric dispersion region. Through detailed numerical simulations, we show that the synthetic dispersion model captures the system's key physical behavior, in which the second pump enables non-degenerate four-wave mixing that produces new dispersive waves on both sides of the spectrum. We experimentally demonstrate these concepts by pumping a silicon nitride microring resonator at 1060 nm and 1550 nm to generate a single soliton microcomb whose bandwidth approaches two octaves (137 THz to 407 THz) and whose phase coherence is verified through beat note measurements. Such ultra-broadband microcombs provide new opportunities for full microcomb stabilization in optical frequency synthesis and optical atomic clocks, while the synthetic dispersion concept can extend microcomb operation to wavelengths that are hard to reach solely through geometric dispersion engineering.

Si$_3$N$_4$ waveguides, pumped at 1550 nm, can provide spectrally smooth, broadband light for gas spectroscopy in the important 2 ${\mathrm{\mu}}$m to 2.5 ${\mathrm{\mu}}$m atmospheric water window, which is only partially accessible with silica-fiber based systems. By combining Er+:fiber frequency combs and supercontinuum generation in tailored Si$_3$N$_4$ waveguides, high signal-to-noise dual-comb spectroscopy (DCS) spanning 2 ${\mathrm{\mu}}$m to 2.5 ${\mathrm{\mu}}$m is demonstrated. Acquired broadband dual-comb spectra of CO and CO$_2$ agree well with database line shape models and have a spectral-signal-to-noise as high as 48$/\sqrt{\mathrm{s}}$, showing that the high coherence between the two combs is retained in the Si$_3$N$_4$ supercontinuum generation. The DCS figure of merit is 6$\times 10^6/\sqrt{\mathrm{s}}$, equivalent to that of all-fiber DCS systems in the 1.6 ${\mathrm{\mu}}$m band. Based on these results, future DCS can combine fiber comb technology with Si$_3$N$_4$ waveguides to access new spectral windows in a robust non-laboratory platform.

We present a hybrid fiber/waveguide design for a 100-MHz frequency comb that is fully self-referenced and temperature controlled with less than 5 W of electrical power. Self-referencing is achieved by supercontinuum generation in a silicon nitride waveguide, which requires much lower pulse energies (~200 pJ) than with highly nonlinear fiber. These low-energy pulses are achieved with an erbium fiber oscillator/amplifier pumped by two 250-mW passively-cooled pump diodes that consume less than 5 W of electrical power. The temperature tuning of the oscillator, necessary to stabilize the repetition rate in the presence of environmental temperature changes, is achieved by resistive heating of a section of gold-palladium-coated fiber within the laser cavity. By heating only the small thermal mass of the fiber, the repetition rate is tuned over 4.2 kHz (corresponding to an effective temperature change of 4.2 {\deg}C) with a fast time constant of 0.5 s, at a low power consumption of 0.077 W/{\deg}C, compared to 2.5 W/{\deg}C in the conventional 200-MHz comb design., Comment: Updated manuscript and added journal information

The study and understanding of the details of proton-proton collisions is important since they are the benchmark for the comparison with heavy ion results. In the present work we have studied the $\Delta\eta\Delta\phi$ correlations as a function of the event multiplicity and transverse sphericity in pp collisions at $\sqrt{s}$ = 7 TeV using PYTHIA 8.180. The results show large variation in the shape of the correlation as a function of the sphericity and multiplicity indicating the importance of slicing the data in bins of both observables to better understand the complexity of the interactions. Motivated by the radial flow patterns originated by color reconnection (CR), results with and without CR together with dihadron correlations are discussed., Comment: 6 pages, 4 figures

A new method to extract information from the pp data is proposed. The approach is based on the use of the event structure variables: sphericity and spherocity, to split the data into enhanced soft and hard processes samples corresponding to events with large and low numbers of multi-parton interactions, respectively. The present study was developed in the framework of Pythia 8.180 for inelastic pp collisions at sqrt(s) =7 TeV. As an application of the method, a study of the identified particle transverse momentum spectra and their ratios; is presented for soft (isotropic) and hard (jetty-like) events. The flow-like effect on these observables due to multi-parton interactions and color reconnection is relevant for soft events suggesting that partons inside the jet do not feel color reconnection and its flow-like consequences., Comment: 4 pages, 4 figures