Search

The cost-effective implementation of nanofibrillated cellulose (CNF) at industrial scale requires optimizing the quality of the nanofibers according to their final application. Therefore, a portfolio of CNFs with different qualities is necessary, as well as further knowledge about how to obtain each of the main qualities. This paper presents the influence of various production techniques on the morphological characteristics and properties of CNFs produced from a mixture of recycled fibers. Five different pretreatments have been investigated: a mechanical pretreatment (PFI refining), two enzymatic hydrolysis strategies, and TEMPO-mediated oxidation under two different NaClO concentrations. For each pretreatment, five high-pressure homogenization (HPH) conditions have been considered. Our results show that the pretreatment determines the yield and the potential of HPH to enhance fibrillation and, therefore, the final CNF properties. These results enable one to select the most effective production method with the highest yield of produced CNFs from recovered paper for the desired CNF quality in diverse applications.

Lignin-containing cellulose nanofibrils (LCNFs) have emerged as a new class of nanocelluloses where the presence of residual lignin is expected to impart additional attributes such as hydrophobicity or UV-absorption. In the present work, LCNFs with a lignin content between 7 and 15 wt% were prepared via a TEMPO-mediated oxidation as chemical pretreatment followed by high-pressure homogenization. The impact of the carboxyl content (CC) on the properties of the resulting LCNF gel, in terms of lignin content, colloidal properties, morphology, crystallinity, and thermal stability, were investigated. It was found that lignin content was significantly decreased at increasing CC. In addition, CC had a positive effect on colloidal stability and water contact angle, as well as resulting in smaller fibrils. This lower size, together with the lower lignin content, resulted in a slightly lower thermal stability. The reinforcing potential of the LCNFs when incorporated into a ductile polymer matrix was also explored by preparing nanocomposite films with different LCNF contents that were mechanically tested under linear and non-linear regimes by dynamic mechanical analysis (DMA) and tensile tests. For comparison purposes, the reinforcing effect of the LCNFs with lignin-free CNFs was also reported based on literature data. It was found that lignin hinders the network-forming capacity of LCNFs, as literature data shows a higher reinforcing potential of lignin-free CNFs. Nonetheless, the tensile strength of the acrylic matrix was enhanced by 10-fold at 10 wt% of LCNF content.

Measurements of nanocellulose size usually demand very high-resolution techniques and tedious image processing, mainly in what pertains to the length of nanofibers. Aiming to ease the process, this work assesses a relatively simple method to estimate the dimensions of nanocellulose particles with an aspect ratio greater than 1. Nanocellulose suspensions, both as nanofibers and as nanocrystals, are subjected to dynamic light scattering (DLS) and to field-emission scanning electron microscopy (FE-SEM). The former provides the hydrodynamic diameter, as long as the scatter angle and the consistency are adequate. Assays with different angles and concentrations compel us to recommend forward scattering (12.8°) and concentrations around 0.05–0.10 wt %. Then, FE-SEM with magnifications of ×5000–×20,000 generally suffices to obtain an acceptable approximation for the actual diameter, at least for bundles. Finally, length can be estimated by a simple geometric relationship. Regardless of whether they are collected from FE-SEM or DLS, size distributions are generally skewed to lower diameters. Width distributions from FE-SEM, in particular, are well fitted to log-normal functions. Overall, while this method is not valid for the thinnest fibrils or for single, small nanocrystals, it can be useful in lieu of very high-resolution techniques.

Food packaging manufacturers often resort to lamination, typically with materials which are neither non-biodegradable nor biobased polymers, to confer barrier properties to paper and cardboard. The present work considers a greener solution: enhancing paper’s resistance to moisture, grease, and air by aqueous coating suspensions. For hydrophobization, a combined approach between nanocellulose and common esterifying agents was considered, but the water vapor transmission rate (WVTR) remained excessively high for the goal of wrapping moisture-sensitive products (>600 g m−2 d−1). Nonetheless, oil-repellant surfaces were effectively obtained with nanocellulose, illite, sodium alginate, and/or poly(vinyl alcohol) (PVA), reaching Kit ratings up to 11. Regarding air resistance, mineral-rich coatings attained values above 1000 Gurley s. In light of these results, nanocellulose, minerals, PVA, pullulan, alginate, and a non-ionic surfactant were combined for multi-purpose coating formulations. It is hypothesized that these materials decrease porosity while complementing each other’s flaws, e.g., PVA succeeds at decreasing porosity but has low dimensional stability. As an example, a suspension mostly constituted by nanocellulose, sizing agents, minerals and PVA yielded a WVTR of roughly 100 g m−2 d−1, a Kit rating of 12, and an air resistance above 300 s/100 mL. This indicates that multi-purpose coatings can be satisfactorily incorporated into paper structures for food packaging applications, although not as the food contact layer.

The current trends in micro-/nanofibers offer a new and unmissable chance for the recovery of cellulose from non-woody crops. This work assesses a technically feasible approach for the production of micro- and nanofibrillated cellulose (MNFC) from jute, sisal and hemp, involving refining and enzymatic hydrolysis as pretreatments. Regarding the latter, only slight enhancements of nanofibrillation, transparency and specific surface area were recorded when increasing the dose of endoglucanases from 80 to 240 mg/kg. This supports the idea that highly ordered cellulose structures near the fiber wall are resistant to hydrolysis and hinder the diffusion of glucanases. Mechanical MNFC displayed the highest aspect ratio, up to 228 for hemp. Increasing the number of homogenization cycles increased the apparent viscosity in most cases, up to 0.14 Pa·s at 100 s−1 (1 wt.% consistency). A shear-thinning behavior, more marked for MNFC from jute and sisal, was evidenced in all cases. We conclude that, since both the raw material and the pretreatment play a major role, the unique characteristics of non-woody MNFC, either mechanical or enzymatically pretreated (low dose), make it worth considering for large-scale processes.

While the potential of cellulose nanofibers to enhance the mechanical and barrier properties of paper is well-known, there are many uncertainties with respect to how to apply them. In this study, we use not only bulk addition of micro-/nanofibers and bar coating with oxidized nanofibers, but also a combination of these and, as a novel element, electrospray deposition of nanofiber dispersions. Characterization involved testing the strength of uncoated and coated paper sheets, their resistance to air flow, their Bendtsen roughness, and their apparent density, plus visualization of their surface and cross-sections by scanning electron microscopy. As expected, bulk addition to the unrefined pulp was sufficient to attain substantial strengthening, but this enhancement was limited to approximately 124%. Following this, surface addition by bar coating improved air resistance, but not strength, since, as applying nanocellulose at high consistency was technically unfeasible, this was performed several times with detrimental drying stages in between. However, replacing bar coating with electrospraying helped us overcome these apparent limitations, producing enhancements in both barrier and tensile properties. It is concluded that electrosprayed nanofibers, owing to their uniform deposition and favorable interactions, operate as an effective binder between fibers (and/or fines).

The present paper proposes a novel approach for the morphological characterization of cellulose nano and microfibers suspensions (CMF/CNFs) based on the analysis of eroded CMF/CNF microscopy images. This approach offers a detailed morphological characterization and quantification of the micro and nanofibers networks present in the product, which allows the mode of fibrillation associated to the different CMF/CNF extraction conditions to be discerned. This information is needed to control CMF/CNF quality during industrial production. Five cellulose raw materials, from wood and non-wood sources, were subjected to mechanical, enzymatic, and (2,2,6,6-Tetramethylpiperidin-1-yl)oxyl (TEMPO)-mediated oxidative pre-treatments followed by different homogenization sequences to obtain products of different morphologies. Skeleton analysis of microscopy images provided in-depth morphological information of CMF/CNFs that, complemented with aspect ratio information, estimated from gel point data, allowed the quantification of: (i) fibers peeling after mechanical pretreatment; (ii) fibers shortening induced by enzymes, and (iii) CMF/CNF entanglement from TEMPO-mediated oxidation. Being mostly based on optical microscopy and image analysis, the present method is easy to implement at industrial scale as a tool to monitor and control CMF/CNF quality and homogeneity.

The feasibility of incorporating purified kraft lignin, at different concentrations ranging from 5 to 29%, into fiberboards made from corn residues was studied. The lignin was obtained from black liquor, which is a residue of the paper industry. Corn stalk raw material and its thermomechanically produced fiber were characterized in terms of their chemical composition. The physical and mechanical properties of the resulting fiberboards were evaluated. The fiberboards produced following a wet process had good mechanical and water resistance properties that satisfied the requirements of the relevant standards. In addition, a Life Cycle Thinking (LCT) approach suggested that lignin-based fiberboards are environmentally preferable than those based on thermosetting resins.

The stalks that are left on the field after harvesting rapeseed crops could be used to make packaging grade paper. This work evaluates the suitability of mechanical and thermomechanical pulps from rapeseed stalks for papermaking, with a view to alleviating the limitations of recycled fluting. Their performance was compared to that of commercial fluting (recycled fluting) of the same basis weight, 100 g/m2, and to that of virgin pulps from pine wood. The thermomechanical pulp was refined to improve key mechanical properties. Its drainability was found to be very low, even before refining, and its breaking length after beating to 1200 PFI revolutions, 4 km, surpassed that of sheets of recycled fluting that were obtained under similar conditions. These findings support the hypothesis that high-yield pulps from rapeseed stalks are a strong choice of virgin fibres to produce fluting and, generally speaking, packaging paper.

Greener composites, as alternatives to more common materials, should also achieve technical and economic feasibility to be commercially competitive. This study presents the results obtained from using a biodegradable starch-based matrix, and a natural fiber reinforcement coming from sugarcane bagasse, currently an agro-waste. The sugarcane bagasse biomass was treated to obtain four kinds of fibers with different morphological and chemical properties. The fibers were used to obtain composite materials, which were then tested for tensile properties. The results showed that some of the composites were suitable to replace high density polyethylene, from a technical and environmental point of view. The comparatively higher cost of the biobased matrices hinders the substitution, but the higher the fiber content, the lower the economic disadvantage. A micromechanical test and a sensitivity analysis showed that the fiber orientation had the highest impact on the tensile strength, followed by the fibers mean length and the quality of the interphase between the fibers and the matrix.

Sugarcane bagasse was treated to obtain sawdust, in addition to mechanical, thermomechanical, and chemical-thermomechanical pulps. The obtained fibers were used to obtain reinforced polypropylene composites prepared by injection molding. Coupling agent contents ranging from 2 to 10% w/w were added to the composite to obtain the highest tensile strength. All the composites included 30% w/w of reinforcing fibers. The tensile strength of the different sugarcane bagasse fiber composites were tested and discussed. The results were compared with that of other natural fiber- or glass fiber-reinforced polypropylene composites. Pulp-based composites showed higher tensile strength than sawdust-based composites. A micromechanical analysis showed the relationship of some micromechanical properties to the orientation angle, critical length, the intrinsic tensile strength, and the interfacial shear strength. The pulps showed similar intrinsic tensile strengths and were higher than that of sawdust. The properties of the sugarcane bagasse composites compared well with other natural fiber-reinforced composites.

Hemp core is a lignocellulosic residue in the production chain of hemp strands. Huge amounts of hemp core are gathered annually in Europe (43,000 tons) with no major application end. Such lignocellulosic wastes have potential as filling or reinforcing material to replace synthetic fibers and wood fibers in polymer composites. In this study, hemp core biomass was treated under different NaOH concentrations and then defibrated by means of Sprout Waldron equipment to obtain single fibers. Polypropylene matrix was reinforced up to 50 wt.% and the resulting hemp core fibers and the flexural properties were investigated. The results show that the flexural strength of composites increased with the intensity of NaOH treatment. The effect of NaOH was attributed to the removal of extractives and lignin in the fiber cell wall leading to improved interfacial adhesion characteristics. Besides, a methodology was established for the estimation of the intrinsic flexural strength of hemp core fibers. The intrinsic flexural strength of hemp core fibers was calculated to be 940 MPa for fibers treated at 10 wt.% of NaOH. In addition, a relationship between the lignin content and the intrinsic strength of the fibers was established.

The use of cellulose nanofibers (CNF) as an additive in papermaking is an attractive alternative to improve paper’s strength. However, the costs of CNF production need to be competitive compared to other approaches aimed at reducing mechanical beating. Five different types of CNFs were prepared following different pretreatments: TEMPO-mediated oxidation at basic and neutral conditions, soft acid hydrolysis, enzymatic treatment, and mechanical beating. All of the pretreated fibers were later passed through a high-pressure homogenizer. The resulting CNFs were each applied to a papermaking pulp to investigate their reinforcing ability. Results indicated that the TEMPO-oxidized CNFs offered the highest increase at the same nanofiber content compared to the other types of CNFs. However, an analysis of the cost of increasing paper’s breaking length by 75% indicated that TEMPO-oxidized CNFs were more expensive than the other CNF grades, whereas CNFs from mechanical and acid pre-treatment offered similar increases at lower prices. The results indicated that CNFs of high fibrillation degree were not necessary to induce dramatic increases in paper strength. This finding offers a new possibility for the escalation of CNF production to industrial levels with competitive prices.

Recycling and deinking processes cause fiber damage because of hornification phenomena and increased external fibrillation. Mechanical refining has been used for many years to enhance the mechanical properties of paper. Biorefining of pulp using enzymes is receiving increasing interest for energy reduction at the refining step of the paper-making process. Moreover, enzymes have also been used for the enhancement of mechanical properties without affecting the drainage rate. As an alternative to mechanical refining treatment, a combination of an enzymatic treatment and cellulose nanofibril (CNF) addition was explored to enhance the mechanical properties of paper. The tests were carried out on a deinked pulp (DIP) suspension made of 50% old newspapers (ONP) and 50% old magazines (OMG). Various enzyme charges and CNF amounts were added to the mixture of ONP and OMG. All pulps (treated and untreated) were characterized from a morphological point of view, and the paper sheets made thereof were mechanically characterized. The combination of the enzymatic treatment with the addition of 3% CNF provided sufficient tensile strength for the paper to be used in high-performance applications.

This paper explores the evolution in the tensile strength of orange pruning fiber-reinforced polypropylene composites. The exploitation of these pruning’s can effectively avoid incineration, with the consequence of CO2 emissions and fire risk, while extending the value chain of the agricultural industry. This biomass was subjected to three different treatments yielding mechanical, thermomechanical, and chemi-thermomechanical pulps. It was found that 20 to 50% of these pulps, together with a coupling agent, were used as polypropylene reinforcement. The evolution in the tensile strength and morphological properties of the fibers, and the effect of treatments on these properties were analyzed. A modified rule of mixtures (mROM) was used to analyze the micromechanical properties of the interface. In addition, the mechanical properties were weighted against the fiber treatment yields. Finally, factors to compute the net contribution of the fibers to the final strength of the composite materials were proposed.

A major drawback of natural-based composites is the incorporation of reinforcements that are less thermally stable than the matrix; therefore, the thermal properties of the resultant composite material needs to be studied. In this work, orange wood fibers were used to reinforce polypropylene. The effects on the thermal properties of the polymeric matrix were analyzed. To this end, differential scanning calorimetry (DSC), thermogravimetry (TGA), thermomechanical analysis (TMA), and dynamic-mechanical analysis (DMA) were performed. It was found that the degradation of the material took place in two distinct phases: the reinforcement, close to 250 °C, and the matrix, above 340 °C. DSC results showed that fiber reinforcement did not influence the transition temperatures of the materials, although it did affect the polymer crystallinity value, increasing by 7% when the composite is reinforced with 50% of the lignocellulosic reinforcement. The coefficient of expansion obtained by TMA indicated that thermal expansion decreased as the amount of reinforcement increased. DMA assays showed that the reinforcement did not modify the glass transition (20 to 25 °C) temperature and confirmed that the addition of reinforcement increased the crystallinity of the product.

Single-use plastics are expected to disappear, mainly due to the rise of stricter regulations to combat their impact on the environment. As an example, the recent European Directive on Single-Use-Plastics (SUP) will be implemented between 2021 and 2024 and will directly prohibit the use of some SUP. Baby diapers are one of the most used single-used products in our daily lives, and it is estimated that most of the ~4000 diapers that each baby uses in their life go to landfill. Such diapers usually contain superabsorbent polymers (SAP) that are based on acrylic acid-acrylamide mixtures with high water retention capacity, but they are neither bio-based nor biodegradable. In this work, we have developed bio-based superabsorbent aerogels made of cellulose nanofibers (CNF) and propose their potential use in baby diapers. TEMPO-oxidized CNF at different oxidation degrees were prepared and tested. The obtained CNF exhibited higher free swelling capacity (FSC) than the commercial fluff pulp (ranging from 117.62% to 245.21% higher) and also than the diaper absorbent, except for CNF-5 (ranging from 31.56% to 54.55%), even under compression. Overall, the present work shows a case study where CNF could have a potential application with market opportunities.

Alpha-grass was studied as the reinforcement in a starch-based polymer matrix. Mater-bi®-Y was chosen as a matrix due to its Young’s modulus, in line with that of polypropylene. The test specimens were injection molded and tensile tested. The obtained results were compared to glass fiber reinforced polypropylene. The reinforcing fibers increased the Young’s modulus significantly, obtaining values up to 7.2 GPa, comparable to those obtained with reinforced polypropylene. The contribution of the fibers to the final composite Young’s modulus was also studied, and it was found that was in line with other natural fibers contribution to polypropylene-based composites. Finally, it was found that the value of the efficiency factor of the module remained similar to that of natural fiber reinforced polypropylene.

In this work, the physical and mechanical properties of bleached Eucalyptus pulp reinforced with nanofibrillated cellulose (NFC) are compared with those of traditional beaten pulp used in the making of writing/printing and offset printing papers. For this purpose, three different types of hardwood slurries were prepared: beaten pulps, unbeaten pulps reinforced with NFC, and slightly beaten pulps also reinforced with NFC. Physical and mechanical tests were performed on handsheets from these different slurries. The results showed that adding NFC to unbeaten pulps results in physical and mechanical properties similar to those in pulps used for printing/writing papers. Nevertheless, the best results were obtained in slurries previously beaten at slight conditions and subsequently reinforced with NFC. These results demonstrate that the addition of NFC allows a reduction in beating intensity without decreasing the desired mechanical properties for this specific purpose.

Two of the drawbacks of using natural-based composites in industrial applications are thermal instability and water uptake capacity. In this work, mechanical wood pulp was used to reinforce polypropylene at a level of 20 to 50 wt. %. Composites were mixed by means of a Brabender internal mixer for both non-coupled and coupled formulations. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to determine the thermal properties of the composites. The water uptake behavior was evaluated by immersion of the composites in water until an equilibrium state was reached. Results of water absorption tests revealed that the amount of water absorption was clearly dependent upon the fiber content. The coupled composites showed lower water absorption compared to the uncoupled composites. The incorporation of mechanical wood pulp into the polypropylene matrix produced a clear nucleating effect by increasing the crystallinity degree of the polymer and also increasing the temperature of polymer degradation. The maximum degradation temperature for stone ground wood pulp–reinforced composites was in the range of 330 to 345 ºC.

Currently, acoustic isolation is one of the problems raised with building construction in Spain. The publication of the Basic Document for the protection against noise of the Technical Building Code has increased the demand of comfort for citizens. This has created the need to seek new composite materials that meet the new required acoustical building codes. In this paper we report the results of the newly developed composites that are able to improve the acoustic isolation of airborne noise. These composites were prepared from polypropylene (PP) reinforced with mechanical pulp fibers from softwood (Pinus radiata). Mechanical and acoustical properties of the composites from mechanical pulp (MP) and polypropylene (PP) have been investigated and compared to fiberglass (FG) composites. MP composites had lower tensile properties compared with FG composites, although these properties can be improved by incorporation of a coupling agent. The results of acoustical properties of MP composites were reported and compared with the conventional composites based on fiberglass and gypsum plasterboards. Finally, we suggest the application of MP composites as a light-weight building material to reduce acoustic transmitions.

The behavior of stone groundwood / polypropylene injection-molded composites was evaluated with and without coupling agent. Stone groundwood (SGW) is a fibrous material commonly prepared in a high yield process and mainly used for papermaking applications. In this work, the use of SGW fibers was explored as a reinforcing element of polypropylene (PP) composites. The surface charge density of the composite components was evaluated, as well as the fiber’s length and diameter inside the composite material. Two mixing extrusion processes were evaluated, and the use of a kinetic mixer, instead of an internal mixer, resulted in longer mean fiber lengths of the reinforcing fibers. On the other hand, the accessibility of surface hydroxyl groups of stone groundwood fibers was improved by treating the fibers with 5% of sodium hydroxide, resulting in a noticeable increase of the tensile strength of the composites, for a similar percentage of coupling agent. A new parameter called Fiber Tensile Strength Factor is defined and used as a baseline for the comparison of the properties of the different composite materials. Finally the competitiveness of stone groundwood / polypropylene / polypropylene-co-maleic anhydride system, which compared favorably to sized glass-fiber / polypropylene GF/PP and glass-fiber / polypropylene / polypropylene-co-maleic anhydride composite formulations, was quantified by means of the fiber tensile strength factor.

The main objective of this study was the management of corn stalk waste as reinforcement for polypropylene (PP) injection moulded composites as an alternative to wood flour and fibers. In the first step, corn stalk waste was subjected to various treatments, and four different corn stalk derivatives (flour and fibers) able to be used as reinforcement of composite materials were prepared and characterized. These derivatives are corn stalk flour, thermo-mechanical, semi-chemical, and chemical fibers. They were characterized in terms of their yield, lignin content, Kappa number, fiber length/diameter ratio, fines, coarseness, viscosity, and the length at the break of a standard sheet of paper. Results showed that the corn stalk derivatives have different physico-chemical properties. In the second step, the prepared flour and fibers were explored as a reinforcing element for PP composites. Coupled and non-coupled PP composites were prepared and tested for tensile properties. For overall trend, with the addition of a coupling agent, tensile properties of composites significantly improved, as compared with non-coupled samples. In addition, a morphological study revealed the positive effect of the coupling agent on the interfacial bonding. The composites prepared with semichemical fiber gave better results in comparison with the rest of the corn stalk derivatives due to its chemical characteristics.

One of the most relevant properties of composite materials to be considered is stiffness. Fiberglass has been used traditionally as a fibrous reinforcing element when stiff materials are required. However, natural fibers are been exploited as replacements for synthetic fibers to satisfy environmental concerns. Among the different natural fibers, wood fibers show the combination of relatively high aspect ratio, good specific stiffness and strength, low density, low cost, and less variability than other natural fibers of such those from annual crops. In this work, composites from polypropylene and stone groundwood fibers from softwood were prepared and mechanically characterized under tensile loads. The Young’s moduli of the ensuing composites were analyzed and their micromechanics aspects evaluated. The reinforcing effect of stone groundwood fibers was compared to that of conventional reinforcement such fiberglass. The Halpin-Tsai model with the modification proposed by Tsai-Pagano accounted fairly for the behavior of PP composites reinforced with stone groundwood fibers. It was also demonstrated that the aspect ratio of the reinforcement plays a role in the Young’s modulus of injection molded specimens.

The disintegration of recovered paper is the first operation in the preparation of recycled pulp. It is known that the defibering process follows a first order kinetics from which it is possible to obtain the disintegration kinetic constant (KD) by means of different ways. The disintegration constant can be obtained from the Somerville index results (%ISV) and from the dissipated energy per volume unit (SS). The %ISV is related to the quantity of non-defibrated paper, as a measure of the non-disintegrated fiber residual (percentage of flakes), which is expressed in disintegration time units. In this work, disintegration kinetics from recycled coated paper has been evaluated, working at 20 rev/s rotor speed and for different fiber consistency (6, 8, 10, 12, and 14%). The results showed that the values of experimental disintegration kinetic constant, KD, through the analysis of Somerville index, as function of time, increased with the disintegration consistency. Therefore, as consistency increased, the disintegration time was drastically reduced. The calculation of the disintegration kinetic constant (modeled KD), extracted from the Rayleigh’s dissipation function, showed a good correlation with the experimental values using the evolution of the Somerville index or with the dissipated energy.

Se ha estudiado el efecto de distintos dosajes en masa de nanofibras de celulosa (CNF ), comprendidas entre un 0 y un 6%, sobre las propiedades físico-mecánicas del papel obtenido a partir de las fibras de pasta mecánica de muela de piedra (SGW). Los resultados obtenidos se han comparado con el procedimiento convencional de refinado a distintos grados (de 0 a 2500 RPM). Posteriormente se ha estudiado la incidencia que tiene la aplicación superficial de las CNF en superficie, sobre el papel sin CNF en masa y con CNF en masa. Los resultados obtenidos mostraron que la rigidez del papel y su longitud de ruptura aumentaron con el grado de refino, sin embargo el grado Schopper – Riegler (ºSR) aumentó de forma importante dificultando el drenaje. La aportación de CNF en masa también aumentó el ºSR y la longitud de ruptura, de esta manera el ºSR de un refino a 1500 rev fue equivalente a un contenido en CNF de entre el 4,5 y 6%, pero su longitud de ruptura resultó ser sensiblemente superior. Puede concluirse que la aplicación de CNF en masa puede contemplarse como una alternativa al refino mecánico y que la aplicación superficial de CNF permite dotar al papel de mejores propiedades sin afectar a la capacidad de drenaje. Abstract The effect of different application amounts of nanofibrilated cellulose (CNF), from 0 to 6%, on the physico-mechanical properties of the paper obtained from stone ground wood pulp fiber has been studied. The results have been compared with the conventional beating process at different degrees (from 0 to 2500 rpm). Afterwards the effect of the application of CNF on the surface, in papers with and without CNF in bulk, has been studied. The results showed that the paper stiffness and breaking length increased with freeness; however the Schopper–Riegler grade (oSR) increased significantly hindering drainage. The contribution of CNF in bulk also increased °SR and breaking length, therefore the °SR beaten at 1500 rev was equivalent to a content of CNF between 4,5 and 6%, but its breaking length was found to be substantially greater. It can be concluded that the CNF in bulk can be viewed as an alternative to mechanical beating and that the application of CNF at the paper surface allows increasing strength properties without affecting the drainage capacity.