Search

This paper investigated the biomechanics of two clinical cases of bone fracture treatments. Both fractures were treated with the same locking compression plate but with different numbers of screws as well as different plate materials. The fracture treated with 12 screws (rigid fixation) failed at 7 weeks with the plate breaking; the fracture with six screws (flexible fixation) endured the entire healing process. It was hypothesized that the plate failure in the unsuccessful case was due to the material fatigue induced by stress concentration in the plate. As the two clinical cases had different fracture locations and different plate materials, finite element simulations were undertaken for each fractured bone fixed by both a rigid and a flexible method. This enabled comparisons to be made between the rigid and flexible fixation methods. The fatigue life was assessed for each fixation method. The results showed that the stress in the rigid fixation methods could be significantly higher than that in flexible fixation methods. The fatigue analyses showed that, with the stress level in flexible fixation (i.e. with fewer screws), the plate was able to endure 2000 days, and that the plate in rigid fixation could fail by fatigue fracture in 20 days. The paper concludes that the rigid fixation method resulted in serious stress concentrations in the plate, which induced fatigue failure. The flexible fixation gave sufficient stability and was better for fracture healing. [ABSTRACT FROM AUTHOR]

BACKGROUND: Metal particles are generated during bone preparation in knee arthroplasty. These particles may produce third-body wear, or may have a role in osteolysis. Knowledge of their characteristics may help in the development of methods to reduce the amount of metal debris during bone cutting procedures. MATERIAL AND METHODS: We performed bony resection of the distal femur and proximal tibia on 15 pig knees, simulating a total knee arthroplasty (TKA). Metal debris was collected from the saw blades, cutting blocks and bone surfaces and cleaned for microanalysis. RESULTS: The average loss of metal from the saw blades was 1.13 mg. The average volume of a wear particle was 3.4 x 10(-16) m(3). From this, it was estimated that approximately 500,000 particles are released from the saw blade alone. Material analysis of the particles indicated that the majority originated from the metallic cutting guides, suggesting that many millions of wear particles would be generated during the surgical procedure. Two particle shapes predominated: platelet shape and ploughed shape. INTERPRETATION: Wear particles are produced during resection for a TKA. These may enter the artificial articulation and cause accelerated wear and macrophage activation. Redesign of cutting blocks and saw blades may reduce the amount of debris produced during surgery. [ABSTRACT FROM AUTHOR]

Because sensory signals often evolve rapidly, they could be instrumental in the emergence of reproductive isolation between species. However, pinpointing their specific contribution to isolating barriers, and the mechanisms underlying their divergence, remains challenging. Here, we demonstrate sexual isolation due to divergence in chemical signals between two populations of Drosophila americana (SC and NE) and one population of D. novamexicana , and dissect its underlying phenotypic and genetic mechanisms. Mating trials revealed strong sexual isolation between Drosophila novamexicana males and SC Drosophila americana females, as well as more moderate bi-directional isolation between D. americana populations. Mating behavior data indicate SC D. americana males have the highest courtship efficiency and, unlike males of the other populations, are accepted by females of all species. Quantification of cuticular hydrocarbon (CHC) profiles-chemosensory signals that are used for species recognition and mate finding in Drosophila -shows that the SC D. americana population differs from the other populations primarily on the basis of compound carbon chain-length. Moreover, manipulation of male CHC composition via heterospecific perfuming-specifically perfuming D. novamexicana males with SC D. americana males-abolishes their sexual isolation from these D. americana females. Of a set of candidates, a single gene-elongase CG17821-had patterns of gene expression consistent with a role in CHC differences between species. Sequence comparisons indicate D. novamexicana and our Nebraska (NE) D. americana population share a derived CG17821 truncation mutation that could also contribute to their shared "short" CHC phenotype. Together, these data suggest an evolutionary model for the origin and spread of this allele and its consequences for CHC divergence and sexual isolation in this group., Competing Interests: The authors have declared no conflict of interest., (© 2021 The Authors. Evolution Letters published by Wiley Periodicals LLC on behalf of Society for the Study of Evolution (SSE) and European Society for Evolutionary Biology (ESEB).)

Study Design: Prospective cohort study., Objectives: Investigate the progressive changes in pedicle morphometry and the spatial relationship between the pedicles and neurovascular structures in patients with AIS during growth. Adolescent idiopathic scoliosis (AIS) is a complex three-dimensional spine deformity. AIS pedicles are known to be asymmetrical when compared to adolescents without scoliosis. Defining the anatomical changes occurring progressively in scoliosis as it increases with time and growth is essential for understanding the pathophysiology of scoliosis and for treatment planning. MRI is the ideal method to study the growing spine without ionising radiation., Methods: 24 females with AIS (mean 12.6 years, right sided main thoracic curves) and 20 non-scoliotic females (mean 11.5 years) were selected from an ongoing database. Participants underwent two 3D MRI scans (3 T scanner, T1, 0.5 mm isotropic voxels) approximately 1 year apart (AIS: mean 1.3 ± 0.05 years, control: mean 1.0 ± 0.1 years). The pedicle width, chord length, pedicle height, transverse pedicle angle, sagittal pedicle angle, distance from vertebrae to aorta and distance from pedicle to dural sac were measured from T5 to T12. Inter- and intra-observer variability was assessed., Results: From scans 1-2 in the AIS group, the dural sac became closer to the left pedicle (p < 0.05, T6, T8-T10 and T12) while the distance from the vertebrae to the aorta increased (p < 0.05, T6-T10). No significant changes in these measurements were observed in the non-scoliotic group. Between scans, the AIS chord length and transverse pedicle angle increased on the left side around the apex (p < 0.05) creating asymmetries not seen in the non-scoliotic cohort. The mean pedicle height increased symmetrically in the non-scoliosis cohort (p < 0.05) and asymmetrically in the AIS group with the right side growing faster than the left at T6-T7 (p < 0.05)., Conclusion: Asymmetrical growth patterns occur in the vertebral posterior elements of AIS patients compared to the symmetrical growth patterns found in the non-scoliotic participants., Level of Evidence: Level II prospective comparative study.

Background: Adolescent idiopathic scoliosis is a common condition affecting 2.5% of the general population. Vertebral body stapling was introduced as a method of fusionless growth modulation for the correction of moderate idiopathic scoliosis (Cobb angles of 20-40°), and was claimed to be more effective than bracing and less invasive than fusion. The aim of this study was to assess the effect of vertebral body stapling on the stiffness of a thoracic motion segment unit under moment controlled load, and to assess the vertebral structural damage caused by the staples., Methods: Thoracic spine motion segments from 6 to 8 week old calves (n=14) were tested in flexion/extension, lateral bending, and axial rotation. The segments were tested un-instrumented, then a left anterolateral intervertebral Shape Memory Alloy (SMA) staple was inserted and the test was repeated. Data were collected from the tenth load cycle of each sequence and stiffness was calculated. The staples were carefully removed and the segments were studied with micro-computed tomography to assess physical damage to the bony structure. Visual assessment of the vertebral bone structure on micro-CT was performed., Findings: There was no change in motion segment stiffness in flexion/extension nor in axial rotation. There was a reduction in stiffness in lateral bending with 30% reduction bending away from the staple and 12% reduction bending towards the staple. Micro-CT showed physeal damage in all the specimens., Interpretation: Intervertebral stapling using SMA staples cause a reduction in spine stiffness in lateral bending. They also cause damage to the endplate epiphyses., Competing Interests: Declaration of competing interest All authors of this manuscript declare they have no disclosures and no personal or financial conflicts of interest in relation to this study., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

Introduction: 3D non-contact surface scanners capture highly accurate, calibrated images of surface topography for 3D structures. This study sought to establish the efficacy and accuracy of using 3D surface scanning to characterise spinal curvature and sagittal plane contour., Methods: 10 healthy female adults with a mean age of 25 years, (standard deviation: 3.6 years) underwent both MRI and 3D surface scanning (3DSS) (Artec Eva, Artec Group Inc., Luxembourg) while lying in the lateral decubitus position on a rigid substrate. Prior to 3DSS, anatomical landmarks on the spinous processes of each participant were demarcated using stickers attached to the skin surface. Following 3DSS, oil capsules (fiducial markers) were overlaid on the stickers and the subject underwent MRI. MRI stacks were processed to measure the thoracolumbar spinous process locations, providing an anatomical reference. 3D coordinates for the markers (surface stickers and MRI oil capsules) and for the spinous processes mapped the spinal column profiles and were compared to assess the quality of fit between the 3DSS and MRI marker positions., Results: The RMSE for the polynomials fit to the spinous process, fiducial and surface marker profiles ranged from 0.17-1.15mm for all subjects. The MRI fiducial marker location was well aligned with the spinous process profile in the thoracic and upper lumbar spine for nine of the subjects. Over the 10 subjects, the mean RMSE between the MRI and 3D scan sagittal profiles for all surface markers was 9.8mm (SD 4.2mm). Curvature was well matched for seven of the subjects, with two showing differing curvatures across the lumbar spine due to inconsistent subject positioning., Conclusion: Comparison of the observed trends for vertebral position measured from MRI and 3DSS, suggested the surface markers may provide a useful method for measuring internal changes in sagittal curvature or skeletal changes., Competing Interests: Sealy of Australia provide support for research projects within the QUT Biomechanics and Spine Research Group, which funds staff salary, student scholarships and equipment. This does not alter our adherence to PLOS ONE policies on sharing data and materials.

Study Design: Bovine motion segments were used to investigate the high-rate compression response of intervertebral discs (IVD) before and after depressurising the nucleus pulposus (NP) by drilling a hole through the cranial endplate into it., Objective: To investigate the effect of depressurising the NP on the force-displacement response, and the energy absorption in IVDs when compressed at high strain rates., Summary of Background Data: The mechanical function of the gelatinous NP located in the center of the IVDs of the spine is unclear. Removal of the NP has been shown to affect the direction of bulge of the inner anulus fibrosus (AF), but at low loading rates removal of the NP pressure does not affect the IVD's stiffness. During sports or injurious events, IVDs are commonly exposed to high loading rates, however, no studies have investigated the mechanical function of the NP at these rates., Methods: Eight bovine motion segments were used to quantify the change in pressure caused by a hole drilled through the cranial endplate into the NP, and eight segments were used to investigate the high-rate response before and after a hole was drilled into the NP., Results: The hole caused a 28.5% drop in the NP pressure. No statistically significant difference was seen in peak force, peak displacement, or energy-absorption of the intact, and depressurized NP groups under impact loading. The IVDs absorbed 72% of the input energy, and there was no rate dependency in the percentage energy absorbed., Conclusion: These results demonstrate that the NP pressure does not affect the transfer of load through, or energy absorbed by, the IVD at high loading rates and the AF, rather than the NP, may play the most important role in transferring load, and absorbing energy at these rates. This should be considered when attempting surgically to restore IVD function., Level of Evidence: N/A.

Background: A new growing rod (GR) design, the semiconstrained growing rod (SCGR), with the added advantage of axial rotation freedom within the components, has been introduced at our center which has been shown to be growth friendly. We hypothesize that the SCGR system would reduce autofusion in vivo, thereby maximizing the coronal plane correction, T1-S1 growth, and the final correction achieved at definitive fusion for children with an early onset scoliosis., Methods: In total, 28 patients had either single or dual 5.5 mm diameter SCGR placed minimally invasively through a submuscular approach. Surgical lengthening procedures occurred approximately every 6 months until the definitive fusion procedure was performed for 18 patients. Scoliosis, kyphosis, and lordosis angles, T1-S1 trunk length, and any complications encountered were evaluated., Results: For the full cohort, before GR insertion, the mean major Cobb curve angle was 72.4 degrees (SD, 18.8; range, 45 to 120), mean T1-S1 trunk length was 282 mm (SD, 59; range, 129 to 365), and at the latest follow-up (mean 6.9 y, SD 3.3, range 2.0 to 13.0), 38.8 degrees (SD, 17.5; range 10 to 90) and 377 mm (SD, 62; range, 225 to 487), respectively. For the subset of 18 patients who have had their final instrumented fusion surgery, the definitive surgery procedure alone produced a correction of the major Cobb curve angle by mean 20.3 degrees (SD, 16.1; P<0.0001), and an increase in the T1-S1 trunk length of mean 31.7 mm (SD, 23.1; P<0.0001). There were 14 complications involving 11 of the 28 patients, giving rise to 5 unplanned surgical interventions and 1 case where GR treatment was abandoned., Conclusions: SCGR patients exhibited statistically significant increase in T1-S1 trunk length and statistically significant decrease in the severity of scoliosis over the course of GR treatment and again, importantly, with the definitive fusion surgery, suggesting that autofusion had been minimized during GR treatment with relatively low complication rates., Level of Evidence: Level IV-case series.

Background: Axial vertebral rotation is a key characteristic of adolescent idiopathic scoliosis (AIS), and its reduction is one of the goals of corrective surgery. Recurrence of deformity after surgical correction may relate to rotation changes that occur in the anterior vertebral column after surgery, but whether any change occurs within the fused segment or in adjacent unfused levels following thoracoscopic anterior spinal fusion (TASF) is unknown. An analysis of measurements from an existing postoperative CT dataset was performed to investigate the occurrence of inter- and intra-vertebral rotation changes after TASF within and adjacent to the fused spinal segment and look for any relationships with the Cobb angle and rib hump in the two years after surgery., Methods: 39 Lenke Type 1 main thoracic patients underwent TASF for progressive AIS and low dose computed tomography scanning of the instrumented levels of the spine at 6 and 24 months after surgery. Vertebral rotation was measured at the superior and inferior endplates on true axial images for all vertebral levels in the fused segment plus one adjacent level cranially and caudally. Intra-observer variability for rotation measurements was assessed using 95% limits of agreement to detect significant changes in inter/intra-vertebral rotation., Results: Significant local changes in inter- and intra-vertebral rotation were found to have occurred between 6 and 24 months after anterior surgical fusion within the fused spinal segment, albeit with no consistent pattern of location or direction within the instrumented fusion construct. No significant en-bloc movement of the entire fused spinal segment relative to the adjacent un-instrumented cranial and caudal intervertebral levels was found. No clear correlation was found between any vertebral rotation changes and Cobb angle or rib hump measures., Conclusions: Localised inter- and intra-vertebral rotation occurs between 6 and 24 months after TASF, both within the instrumented spinal segments and in the adjacent un-instrumented levels of the adolescent spine. The lack of measurable en-bloc movement of the fused segment relative to the adjacent un-instrumented levels suggests that overall stability of the instrumented construct is achieved, however the vertebrae within the fusion mass continue to adapt and remodel, resulting in ongoing local anatomical and biomechanical changes in the adolescent spine.

Purpose: To assess the feasibility of diffusion tensor imaging (DTI) for evaluating changes in anulus fibrosus (AF) microstructure following uniaxial compression., Materials and Methods: Six axially aligned samples of AF were obtained from a merino sheep disc; two each from the anterior, lateral, and posterior regions. The samples were mechanically loaded in axial compression during five cycles at a rate and maximum compressive strain that reflected physiological conditions. DTI was conducted at 7T for each sample before and after mechanical testing., Results: The mechanical response of all samples in unconfined compression was nonlinear. A stiffer response during the first loading cycle, compared to the remaining cycles, was observed. Change in diffusion parameters appeared to be region-dependent. The mean fractional anisotropy increased following mechanical testing. This was smallest in the lateral (2% and 9%) and largest in the anterior and posterior samples (17-25%). The mean average diffusivity remained relatively constant (<2%) after mechanical testing in the lateral and posterior samples, but increased (by 5%) in the anterior samples. The mean angle made by the principal eigenvector with the spine axis in the lateral samples was 73° and remained relatively constant (<2%) following mechanical testing. This angle was smaller in the anterior (55°) and posterior (47°) regions and increased by 6-16° following mechanical testing., Conclusion: These preliminary results suggest that axial compression reorients the collagen fibers, such that they become more consistently aligned parallel to the plane of the endplates., Level of Evidence: 1 Technical Efficacy: Stage 1 J. MAGN. RESON. IMAGING 2017;45:1723-1735., (© 2016 International Society for Magnetic Resonance in Medicine.)

Study Design: The aim of this study was to measure contributions of individual vertebra and disc wedging to coronal Cobb angle in the growing scoliotic spine using sequential magnetic resonance imaging (MRI). Clinically, the Cobb angle measures the overall curve in the coronal plane but does not measure individual vertebra and disc wedging. It was hypothesized that patients whose deformity progresses will have different patterns of coronal wedging in vertebrae and discs to those of patients whose deformities remain stable., Methods: A group of adolescent idiopathic scoliosis (AIS) patients each received two to four MRI scans (spaced 3-12 months apart). The coronal plane wedge angles of each vertebra and disc in the major curve were measured for each scan, and the proportions and patterns of wedging in vertebrae and discs were analyzed for subgroups of patients whose spinal deformity did and did not progress during the study period., Results: Sixteen patients were included in the study; the mean patient age was 12.9 years (standard deviation 1.7 years). All patients were classified as right-sided major thoracic Lenke Type 1 curves (9 type 1A, 4 type 1B, and 3 type 1C). Cobb angle progression of ≥5° between scans was seen in 56% of patients. Although there were measurable changes in the wedging of individual vertebrae and discs in all patients, there was no consistent pattern of deformity progression between patients who progressed and those who did not. The patterns of progression found in this study did not support the hypothesis of wedging commencing in the discs and then transferring to the vertebrae., Conclusion: Sequential MRI data showed complex patterns of deformity progression. Changes to the wedging of individual vertebrae and discs may occur in patients who have no increase in Cobb angle; therefore, the Cobb method alone may be insufficient to capture the complex mechanisms of deformity progression., (Copyright © 2016 Scoliosis Research Society. Published by Elsevier Inc. All rights reserved.)

Study Design: Biomechanical experiment., Objective: The aims of the present study were to test the effect of fascial tension on lumbar segmental axial rotation and lateral flexion and the effect of the angle of fascial attachment., Summary of Background Data: Tension in the middle layer of lumbar fascia has been demonstrated to affect mechanical properties of lumbar segmental flexion and extension in the neutral zone. The effect of tension on segmental axial rotation and lateral flexion has, however, not been investigated., Methods: Seven unembalmed lumbar spines were divided into segments and mounted for testing. A 6 degree-of-freedom robotic testing facility was used to displace the segments in each anatomical plane (flexion-extension, lateral bending, and axial rotation) with force and moment data recorded by a load cell positioned beneath the test specimen. Tests were performed with and without a 20 N fascia load and the subsequent forces and moments were compared. In addition, forces and moments were compared when the specimens were held in a set position and the fascia loading angle was varied., Results: A fascial tension of 20 N had no measurable effect on the forces or moments measured when the specimens were displaced in any plane of motion (P > 0.05). When 20 N of fascial load were applied to motion segments in a set position small segmental forces and moments were measured. Changing the angle of the fascial load did not significantly alter these measurements., Conclusion: Application of a 20 N fascial load did not produce a measureable effect on the mechanics of a motion segment, even though it did produce small measurable forces and moments on the segments when in a fixed position. Results from the present study are inconsistent with previous studies, suggesting that further investigation using multiple testing protocols and different loading conditions is required to determine the effects of fascial loading on spinal segment behavior., Level of Evidence: N/A.

Adolescent idiopathic scoliosis (AIS) is a three-dimensional (3D) spinal deformity of unknown aetiology. Increased growth of the anterior part of the vertebrae known as anterior overgrowth has been proposed as a potential driver for AIS initiation and progression. To date, there has been no objective evaluation of the 3D measurement techniques used to identify this phenomenon and the majority of previous studies use 2D planar assessments which contain inherent projection errors due to the vertebral rotation which is part of the AIS deformity. In this study, vertebral body (VB) heights and wedge angles were measured in a test group of AIS patients and healthy controls using four different image analysis and measurement techniques. Significant differences were seen between the techniques in terms of VB heights and VB wedge angles. The low variability, and the fact that the rotation and tilt of the deformed VBs are taken into account, suggests that the proposed technique using the full 3D orientation of the vertebrae is the most reliable method to measure anterior and posterior VB heights and sagittal plane wedge angles in 3D image data sets. These results have relevance for future investigations that aim to quantify anterior overgrowth in AIS patients for comparison with healthy controls.

Purpose: Cadaveric studies have previously documented a typical pattern of venous drainage within vertebral bodies (VBs), comprised primarily of the basivertebral vein. These studies, however, are limited by the number of samples available. MRI is able to provide 3D images of soft tissue structures in the spine, including the basivertebral vein without the use of contrast in both healthy controls and subjects with abnormal anatomy such as adolescent idiopathic scoliosis (AIS). This study aimed to quantify the venous networks within VBs of 15 healthy adolescent controls and 15 AIS patients., Methods: Five transverse slices through the VBs were examined simultaneously and the observable vascular network traced. The length of the network on the left and right sides of the VB was calculated, and the spatial patterning assessed level-by-level within each subject., Results: Significant differences were seen in the left/right distribution of vessels in both the control and AIS subjects, with both groups having greater length on the right side of all of their VBs. No difference was seen between AIS and control subjects in any region. Large individual variations in patterns were seen in both groups; however, the control group showed more consistent spatial patterning of the vascular networks across levels in comparison to the AIS group., Conclusion: The length of the basivertebral vein was seen to have a significant bias to the right hand side of the VB in both healthy and AIS adolescents. The spatial pattern of this vein showed large variations in branching both within and across individuals. No significant differences were seen between AIS and control subjects, suggesting both that this network is preserved in deformed AIS vertebrae, and that the vertebral venous system does not play a role in the etiology of AIS.

Background: Adolescent idiopathic scoliosis is a complex three-dimensional deformity of the spine characterized by deformities in the sagittal, coronal, and axial planes. Spinal fusion using pedicle screw instrumentation is a widely used method for surgical correction in severe (coronal deformity, Cobb angle > 45°) adolescent idiopathic scoliosis curves. Understanding the anatomic difference in the pedicles of patients with adolescent idiopathic scoliosis is essential to reduce the risk of neurovascular or visceral injury through pedicle screw misplacement., Questions/purposes: To use CT scans (1) to analyze pedicle anatomy in the adolescent thoracic scoliotic spine comparing concave and convex pedicles and (2) to assess the intra- and interobserver reliability of these measurements to provide critical information to spine surgeons regarding size, length, and angle of projection., Methods: Between 2007 and 2009, 27 patients with adolescent idiopathic scoliosis underwent thoracoscopic anterior correction surgery by two experienced spinal surgeons. Preoperatively, each patient underwent a CT scan as was their standard of care at that time. Twenty-two patients (mean age, 15.7 years; SD, 2.4 years; range, 11.6-22 years) (mean Cobb angle, 53°; SD, 5.3°; range, 42°-63°) were selected. Inclusion criteria were a clinical diagnosis of adolescent idiopathic scoliosis, female, and Lenke type 1 adolescent idiopathic scoliosis with the major curve confined to the thoracic spine. Using three-dimensional image analysis software, the pedicle width, inner cortical pedicle width, pedicle height, inner cortical pedicle height, pedicle length, chord length, transverse pedicle angle, and sagittal pedicle angles were measured. Randomly selected scans were remeasured by two of the authors and the reproducibility of the measurement definitions was validated through limit of agreement analysis., Results: The concave pedicle widths were smaller compared with the convex pedicle widths at T7, T8, and T9 by 37% (3.44 mm ± 1.16 mm vs 4.72 mm ± 1.02 mm; p < 0.001; mean difference, 1.27 mm; 95% CI, 0.92 mm-1.62 mm), 32% (3.66 mm ± 1.00 mm vs 4.82 mm ± 1.10 mm; p < 0.001; mean difference, 1.16 mm; 95% CI, 0.84 mm-1.49 mm), and 25% (4.10 mm ± 1.57 mm vs 5.12 mm ± 1.17 mm; p < 0.001; mean difference, 1.02 mm; 95% CI, 0.66 mm-1.39 mm), respectively. The concave pedicle heights were smaller than the convex at T5 (9.43 mm ± 0.98 vs 10.63 mm ± 1.10 mm; p = 0.002; mean difference, 1.02 mm; 95% CI, 0.59 mm-1.45 mm), T6 (8.87 mm ± 1.37 mm vs 10.88 mm ± 0.81 mm; p < 0.001; mean difference, 2.02 mm; 95% CI, 1.40 mm-2.63 mm), T7 (9.09 mm ± 1.24 mm vs 11.35 mm ± 0.84 mm; p < 0.001; mean difference, 2.26 mm; 95% CI, 1.81 mm-2.72 mm), and T8 (10.11 mm ± 1.05 mm vs 11.86 mm ± 0.88 mm; p < 0.001; mean difference, 1.75 mm; 95% CI, 1.30 mm-2.19 mm). Conversely, the concave transverse pedicle angle was larger than the convex at levels T6 (11.37° ± 4.48° vs 8.82° ± 4.31°; p = 0.004; mean difference, 2.54°; 95% CI, 1.10°-3.99°), T7 (12.69° ± 5.93° vs 8.65° ± 3.79°; p = 0.002; mean difference, 4.04°; 95% CI, 1.90°-6.17°), T8 (13.24° ± 5.28° vs 7.66° ± 4.87°; p < 0.001; mean difference, 5.58°; 95% CI, 2.99°-8.17°), and T9 (19.95° ± 5.69° vs 8.21° ± 4.02°; p < 0.001; mean difference, 4.74°; 95% CI, 2.68°-6.80°), indicating a more posterolateral to anteromedial pedicle orientation., Conclusions: There is clinically important asymmetry in the morphologic features of pedicles in individuals with adolescent idiopathic scoliosis. The concave side of the curve compared with the convex side is smaller in height and width periapically. Furthermore, the trajectory of the pedicle is more acute on the convex side of the curve compared with the concave side around the apex of the curve. Knowledge of these anatomic variations is essential when performing scoliosis correction surgery to assist with selecting the correct pedicle screw size and trajectory of insertion to reduce the risk of pedicle wall perforation and neurovascular injury.

Purpose: The dimensions of the thoracic intervertebral foramen in adolescent idiopathic scoliosis (AIS) have not previously been quantified. Better understanding of the dimensions of the foramen may be useful in surgical planning. This study describes a reproducible method for measurement of the thoracic foramen in AIS using computed tomography (CT)., Methods: In 23 preoperative female patients with Lenke 1 type AIS with right-side convexity major curves confined to the thoracic spine the foraminal height (FH), foraminal width (FW), pedicle to superior articular process distance (P-SAP), and cross-sectional foraminal area (FA) were measured using multiplanar reconstructed CT. Measurements were made at entrance, midpoint, and exit of the thoracic foramina from T1-T2 to T11-T12. Results were also correlated with dependent variables of major curve Cobb angle measured on X-ray and CT, age, weight, Lenke classification subtype, Risser grade, and number of spinal levels in the major curve., Results: The FH, FW, P-SAP, and FA dimensions and ratios are all significantly larger on the convexity of the major curve and maximal at or close to the apex. Mean thoracic foraminal dimensions change in a predictable manner relative to position on the major thoracic curve. There was no statistically significant correlation with the measured foraminal dimensions or ratios and the individual dependent variables. The average ratio of convexity to concavity dimensions at the apex foramina for entrance, midpoint, and exit, respectively, are FH (1.50, 1.38, 1.25), FW (1.28, 1.30, 0.98), FA (2.06, 1.84, 1.32), and P-SAP (1.61, 1.47, 1.30)., Conclusion: Foraminal dimensions of the thoracic spine are significantly affected by AIS. Foraminal dimensions have a predictable convexity-to-concavity ratio relative to the proximity to the major curve apex. Surgeons should be aware of these anatomical differences during scoliosis correction surgery., (Copyright © 2016 Scoliosis Research Society. Published by Elsevier Inc. All rights reserved.)

Study Design: Anterior and posterior vertebral body heights were measured from sequential magnetic resonance imaging (MRI) scans of adolescent idiopathic scoliosis (AIS) patients and healthy controls., Objective: To measure changes in vertebral body height over time during scoliosis progression to assess how vertebral body height discrepancies change during growth., Summary of Background Data: Relative anterior overgrowth has been proposed as a potential driver for AIS initiation and progression. This theory proposes that the anterior column grows faster, and the posterior column slower, in AIS patients when compared with healthy controls. There is a disagreement in the literature as to whether the anterior vertebral body heights are proportionally greater than posterior vertebral body heights in AIS patients when compared with healthy controls. To some extent, these discrepancies may be attributed to methodological differences., Methods: MRI scans of the major curve of 21 AIS patients (mean age 12.5 ± 1.4 years, mean Cobb 32.2 ± 12.8 degrees) and between T4 and T12 of 21 healthy adolescents (mean age 12.1 ± 0.5 years) were captured for this study. Of the 21 AIS patients, 14 had a second scan on average 10.8 ± 4.7 months after the first. Anterior and posterior vertebral body heights were measured from the true sagittal plane of each vertebra such that anterior overgrowth could be quantified., Results: The difference between anterior and posterior vertebral body height in healthy, nonscoliotic children was significantly greater than in AIS patients with mild to moderate scoliosis. There was; however, no significant relationship between the overall anterior-posterior vertebral body height difference in AIS and either severity of the curve or its progression over time., Conclusion: Whilst AIS patients have a proportionally longer anterior column than nonscoliotic controls, the degree of anterior overgrowth was not related to the rate of progression or the severity of the scoliotic curve., Level of Evidence: 3.

Background: Segmental biomechanics of the scoliotic spine are important since the overall spinal deformity is comprised of the cumulative coronal and axial rotations of individual joints. This study investigates the coronal plane segmental biomechanics for adolescent idiopathic scoliosis patients in response to physiologically relevant axial compression., Methods: Individual spinal joint compliance in the coronal plane was measured for a series of 15 idiopathic scoliosis patients using axially loaded magnetic resonance imaging. Each patient was first imaged in the supine position with no axial load, and then again following application of an axial compressive load. Coronal plane disc wedge angles in the unloaded and loaded configurations were measured. Joint moments exerted by the axial compressive load were used to derive estimates of individual joint compliance., Findings: The mean standing major Cobb angle for this patient series was 46°. Mean intra-observer measurement error for endplate inclination was 1.6°. Following loading, initially highly wedged discs demonstrated a smaller change in wedge angle, than less wedged discs for certain spinal levels (+2,+1,-2 relative to the apex, (p<0.05)). Highly wedged discs were observed near the apex of the curve, which corresponded to lower joint compliance in the apical region., Interpretation: While individual patients exhibit substantial variability in disc wedge angles and joint compliance, overall there is a pattern of increased disc wedging near the curve apex, and reduced joint compliance in this region. Approaches such as this can provide valuable biomechanical data on in vivo spinal biomechanics of the scoliotic spine, for analysis of deformity progression and surgical planning., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Background: Adolescent Idiopathic Scoliosis is the most common type of spinal deformity, and whilst the isk of progression appears to be biomechanically mediated (larger deformities are more likely to progress), the detailed biomechanical mechanisms driving progression are not well understood. Gravitational forces in the upright position are the primary sustained loads experienced by the spine. In scoliosis they are asymmetrical, generating moments about the spinal joints which may promote asymmetrical growth and deformity progression. Using 3D imaging modalities to estimate segmental torso masses allows the gravitational loading on the scoliotic spine to be determined. The resulting distribution of joint moments aids understanding of the mechanics of scoliosis progression., Methods: Existing low-dose CT scans were used to estimate torso segment masses and joint moments for 20 female scoliosis patients. Intervertebral joint moments at each vertebral level were found by summing the moments of each of the torso segment masses above the required joint., Results: The patients' mean age was 15.3 years (SD 2.3; range 11.9-22.3 years); mean thoracic major Cobb angle 52(°) (SD 5.9(°); range 42-63(°)) and mean weight 57.5 kg (SD 11.5 kg; range 41-84.7 kg). Joint moments of up to 7 Nm were estimated at the apical level. No significant correlation was found between the patients' major Cobb angles and apical joint moments., Conclusions: Patients with larger Cobb angles do not necessarily have higher joint moments, and curve shape is an important determinant of joint moment distribution. These findings may help to explain the variations in progression between individual patients. This study suggests that substantial corrective forces are required of either internal instrumentation or orthoses to effectively counter the gravity-induced moments acting to deform the spinal joints of idiopathic scoliosis patients.

Background Context: There are differences in the definitions of end plate lesions (EPLs), often referred to as Schmorl's nodes, that may, to some extent, account for the large range of reported prevalence (3.8%-76%)., Purpose: The purpose of this study was to develop a technique to measure the size, prevalence, and location of EPLs in a consistent manner., Study Design/setting: This study proposed a method using a detection algorithm that was applied to five adolescent females (average age, 15.1 [range, 13.0-19.2] years) with idiopathic scoliosis (average major Cobb angle, 60° [range, 55°-67°])., Methods: Existing low-dose, computed tomography scans were segmented semiautomatically to extract three-dimensional morphology of each vertebral end plate. Any remaining attachments to the posterior elements of adjacent vertebrae or end plates were then manually sectioned. An automatic algorithm was used to determine the presence and position of EPLs., Results: End plate lesions were identified in 15 of the 170 (8.8%) end plates analyzed with an average depth of 3.1 mm. Eleven of the 15 EPLs were seen in the lumbar spine. The algorithm was found to be most sensitive to changes in the minimum EPL gradient at the edges of the EPL., Conclusions: This study describes an imaging analysis technique for consistent measurement of the prevalence, location, and size of EPLs. The technique can be used to analyze large populations without observer errors in EPL definitions., (Copyright © 2015 Elsevier Inc. All rights reserved.)

Background: The use of dual growing rods is a fusionless surgical approach to the treatment of early onset scoliosis which aims to harness potential growth and correct spinal deformity. The purpose of this study was to compare the in-vitro biomechanical response of two different dual rod designs under axial rotation loading., Methods: Six porcine spines were dissected into seven level thoracolumbar multi-segment units. Each specimen was mounted and tested in a biaxial Instron machine, undergoing nondestructive left and right axial rotation to peak moments of 4 Nm at a constant rotation rate of 8 deg. s(-1). A motion tracking system (Optotrak) measured 3D displacements of individual vertebrae. Each spine was tested in an un-instrumented state first and then with appropriately sized semi-constrained and 'rigid' growing rods in alternating sequence. The range of motion, neutral zone size and stiffness were calculated from the moment-rotation curves and intervertebral range of motion was calculated from Optotrak data., Findings: Irrespective of test sequence, rigid rods showed a significant reduction of total rotation across all instrumented levels (with increased stiffness) whilst semi-constrained rods exhibited similar rotational behavior to the un-instrumented spines (P<0.05). An 11.1% and 8.0% increase in stiffness for left and right axial rotation respectively and 14.9% reduction in total range of motion were recorded with dual rigid rods compared with semi-constrained rods., Interpretation: Based on these findings, the Semi-constrained growing rods were shown to not increase axial rotation stiffness compared with un-instrumented spines. This is thought to provide a more physiological environment for the growing spine compared to dual rigid rod constructs., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Background: Supine imaging modalities provide valuable 3D information on scoliotic anatomy, but the altered spine geometry between the supine and standing positions affects the Cobb angle measurement. Previous studies report a mean 7°-10° Cobb angle increase from supine to standing, but none have reported the effect of endplate pre-selection or whether other parameters affect this Cobb angle difference., Methods: Cobb angles from existing coronal radiographs were compared to those on existing low-dose CT scans taken within three months of the reference radiograph for a group of females with adolescent idiopathic scoliosis. Reformatted coronal CT images were used to measure supine Cobb angles with and without endplate pre-selection (end-plates selected from the radiographs) by two observers on three separate occasions. Inter and intra-observer measurement variability were assessed. Multi-linear regression was used to investigate whether there was a relationship between supine to standing Cobb angle change and eight variables: patient age, mass, standing Cobb angle, Risser sign, ligament laxity, Lenke type, fulcrum flexibility and time delay between radiograph and CT scan., Results: Fifty-two patients with right thoracic Lenke Type 1 curves and mean age 14.6 years (SD 1.8) were included. The mean Cobb angle on standing radiographs was 51.9° (SD 6.7). The mean Cobb angle on supine CT images without pre-selection of endplates was 41.1° (SD 6.4). The mean Cobb angle on supine CT images with endplate pre-selection was 40.5° (SD 6.6). Pre-selecting vertebral endplates increased the mean Cobb change by 0.6° (SD 2.3, range -9° to 6°). When free to do so, observers chose different levels for the end vertebrae in 39% of cases. Multi-linear regression revealed a statistically significant relationship between supine to standing Cobb change and fulcrum flexibility (p = 0.001), age (p = 0.027) and standing Cobb angle (p < 0.001). The 95% confidence intervals for intra-observer and inter-observer measurement variability were 3.1° and 3.6°, respectively., Conclusions: Pre-selecting vertebral endplates causes minor changes to the mean supine to standing Cobb change. There is a statistically significant relationship between supine to standing Cobb change and fulcrum flexibility such that this difference can be considered a potential alternative measure of spinal flexibility.

There is growing interest in the biomechanics of "fusionless" implant constructs used for deformity correction in the thoracic spine; however, there are questions over the comparability of in vitro biomechanical studies from different research groups due to the various methods used for specimen preparation, testing and data collection. The aim of this study was to identify the effect of two key factors on the stiffness of immature bovine thoracic spine motion segments: (1) repeated cyclic loading and (2) multiple freeze-thaw cycles, to aid in the planning and interpretation of in vitro studies. Two groups of thoracic spine motion segments from 6- to 8-week-old calves were tested in flexion/extension, right/left lateral bending and right/left axial rotation under moment control. Group A was tested with continuous repeated cyclic loading for 500 cycles with data recorded at cycles 3, 5, 10, 25, 50, 100, 200, 300, 400 and 500. Group (B) was tested after each of five freeze-thaw sequences, with data collected from the 10th load cycle in each sequence. Results of testing showed that for Group A: flexion/extension stiffness reduced significantly over the 500 load cycles (-22%; p = 0.001), but there was no significant change between the 5th and 200th load cycles. Lateral bending stiffness decreased significantly (-18%; p = 0.009) over the 500 load cycles, but there was no significant change in axial rotation stiffness (p = 0.137). Group B: there was no significant difference between mean stiffness over the five freeze-thaw sequences in flexion/extension (p = 0.813) and a near-significant reduction in mean stiffness in axial rotation (-6%; p = 0.07). However, there was a statistically significant increase in stiffness in lateral bending (+30%; p = 0.007). Study findings indicate that comparison of in vitro testing results for immature thoracic bovine spine segments between studies can be performed with up to 200 load cycles without significant changes in stiffness. However, when testing protocols require greater than 200 cycles, or when repeated freeze-thaw cycles are involved, it is important to account for the effect of cumulative load and freeze-thaw cycles on spine segment stiffness., (© IMechE 2014.)

Background: Adolescent idiopathic scoliosis is the most common type of spinal deformity whose aetiology remains unclear. Studies suggest that gravitational forces in the standing position play an important role in scoliosis progression, therefore anthropometric data is required to develop biomechanical models of the deformity. Few studies have analysed the trunk by vertebral level and none have performed investigations of the scoliotic trunk. The aim of this study was to determine the centroid, thickness, volume and estimated mass, for sections of the scoliotic trunk., Methods: Existing low-dose CT scans were used to estimate vertebral level-by-level torso masses for 20 female adolescent idiopathic scoliosis patients. ImageJ processing software was used to analyse the CT images and enable estimation of the segmental torso mass corresponding to each vertebral level., Findings: The patients' mean age was 15.0 (SD 2.7) years with mean major Cobb angle of 52 (SD 5.9)° and mean patient weight of 58.2 (SD 11.6) kg. The magnitude of torso segment mass corresponding to each vertebral level increased by 150% from 0.6kg at T1 to 1.5kg at L5. Similarly, segmental thickness from T1-L5 increased inferiorly from a mean 18.5 (SD 2.2) mm at T1 to 32.8 (SD 3.4) mm at L5. The mean total trunk mass, as a percentage of total body mass, was 27.8 (SD 0.5) % which was close to values reported in previous literature., Interpretation: This study provides new anthropometric reference data on segmental (vertebral level-by-level) torso mass in adolescent idiopathic scoliosis patients, useful for biomechanical models of scoliosis progression and treatment., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

We propose the progressive mechanical expansion of cell-derived tissue analogues as a novel, growth-based approach to in vitro tissue engineering. The prevailing approach to producing tissue in vitro is to culture cells in an exogenous "scaffold" that provides a basic structure and mechanical support. This necessarily pre-defines the final size of the implantable material, and specific signals must be provided to stimulate appropriate cell growth, differentiation and matrix formation. In contrast, surgical skin expansion, driven by increments of stretch, produces increasing quantities of tissue without trauma or inflammation. This suggests that connective tissue cells have the innate ability to produce growth in response to elevated tension. We posit that this capacity is maintained in vitro, and that order-of-magnitude growth may be similarly attained in self-assembling cultures of cells and their own extracellular matrix. The hypothesis that growth of connective tissue analogues can be induced by mechanical expansion in vitro may be divided into three components: (1) tension stimulates cell proliferation and extracellular matrix synthesis; (2) the corresponding volume increase will relax the tension imparted by a fixed displacement; (3) the repeated application of static stretch will produce sustained growth and a tissue structure adapted to the tensile loading. Connective tissues exist in a state of residual tension, which is actively maintained by resident cells such as fibroblasts. Studies in vitro and in vivo have demonstrated that cellular survival, reproduction, and matrix synthesis and degradation are regulated by the mechanical environment. Order-of-magnitude increases in both bone and skin volume have been achieved clinically through staged expansion protocols, demonstrating that tension-driven growth can be sustained over prolonged periods. Furthermore, cell-derived tissue analogues have demonstrated mechanically advantageous structural adaptation in response to applied loading. Together, these data suggest that a program of incremental stretch constitutes an appealing way to replicate tissue growth in cell culture, by harnessing the constituent cells' innate mechanical responsiveness. In addition to offering a platform to study the growth and structural adaptation of connective tissues, tension-driven growth presents a novel approach to in vitro tissue engineering. Because the supporting structure is secreted and organised by the cells themselves, growth is not restricted by a "scaffold" of fixed size. This also minimises potential adverse reactions to exogenous materials upon implantation. Most importantly, we posit that the growth induced by progressive stretch will allow substantial volumes of connective tissue to be produced from relatively small initial cell numbers., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Right heart dysfunction is one of the most serious complications following implantation of a left ventricular assist device, often leading to the requirement for short- or long-term right ventricular assist device (RVAD) support. The inflow cannulation site induces major hemodynamic changes and so there is a need to optimize the site used depending on the patient's condition. Therefore, this study evaluated and compared the hemodynamic influence of right atrial cannulation (RAC) and right ventricular cannulation (RVC) inflow sites. An in vitro variable heart failure mock circulation loop was used to compare RAC and RVC in mild and severe biventricular heart failure (BHF) conditions. In the severe BHF condition, higher ventricular ejection fraction (RAC: 13.6%, RVC: 32.7%) and thus improved heart chamber and RVAD washout were observed with RVC, which suggested this strategy might be preferable for long-term support (i.e., bridge-to-transplant or destination therapy) to reduce the risk of thrombus formation. In the mild BHF condition, higher pulmonary valve flow (RAC: 3.33 L/min, RVC: 1.97 L/min) and lower right ventricular stroke work (RAC: 0.10 W, RVC: 0.13 W) and volumes were recorded with RAC. These results indicate an improved potential for myocardial recovery, thus RAC should be chosen in this condition. This in vitro study suggests that RVAD inflow cannulation site should be chosen on a patient-specific basis with a view to the support strategy to promote myocardial recovery or reduce the risk of long-term complications., (© 2013, Copyright the Authors. Artificial Organs © 2013 Wiley Periodicals, Inc. and International Center for Artificial Organs and Transplantation.)

Successful anatomic fitting of a total artificial heart (TAH) is vital to achieve optimal pump hemodynamics after device implantation. Although many anatomic fitting studies have been completed in humans prior to clinical trials, few reports exist that detail the experience in animals for in vivo device evaluation. Optimal hemodynamics are crucial throughout the in vivo phase to direct design iterations and ultimately validate device performance prior to pivotal human trials. In vivo evaluation in a sheep model allows a realistically sized representation of a smaller patient, for which smaller third-generation TAHs have the potential to treat. Our study aimed to assess the anatomic fit of a single device rotary TAH in sheep prior to animal trials and to use the data to develop a three-dimensional, computer-aided design (CAD)-operated anatomic fitting tool for future TAH development. Following excision of the native ventricles above the atrio-ventricular groove, a prototype TAH was inserted within the chest cavity of six sheep (28-40 kg). Adjustable rods representing inlet and outlet conduits were oriented toward the center of each atrial chamber and the great vessels, with conduit lengths and angles recorded for future analysis. A three-dimensional, CAD-operated anatomic fitting tool was then developed, based on the results of this study, and used to determine the inflow and outflow conduit orientation of the TAH. The mean diameters of the sheep left atrium, right atrium, aorta, and pulmonary artery were 39, 33, 12, and 11 mm, respectively. The center-to-center distance and outer-edge-to-outer-edge distance between the atria, found to be 39 ± 9 mm and 72 ± 17 mm in this study, were identified as the most critical geometries for successful TAH connection. This geometric constraint restricts the maximum separation allowable between left and right inlet ports of a TAH to ensure successful alignment within the available atrial circumference., (© 2013, Copyright the Authors. Artificial Organs © 2013 Wiley Periodicals, Inc. and International Center for Artificial Organs and Transplantation.)

Owing to the successful use of non-invasive vibration analysis to monitor the progression of dental implant healing and stabilization, it is now being considered as a method to monitor femoral implants in transfemoral amputees. This study uses composite femur-implant physical models to investigate the ability of modal analysis to detect changes at the interface between the implant and bone simulating those that occur during osseointegration. Using electromagnetic shaker excitation, differences were detected in the resonant frequencies and mode shapes of the model when the implant fit in the bone was altered to simulate the two interface cases considered: firm and loose fixation. The study showed that it is beneficial to examine higher resonant frequencies and their mode shapes (rather than the fundamental frequency only) when assessing fixation. The influence of the model boundary conditions on the modal parameters was also demonstrated. Further work is required to more accurately model the mechanical changes occurring at the bone-implant interface in vivo, as well as further refinement of the model boundary conditions to appropriately represent the in vivo conditions. Nevertheless, the ability to detect changes in the model dynamic properties demonstrates the potential of modal analysis in this application and warrants further investigation.

Rotary ventricular assist device (VAD) support of the cardiovascular system is susceptible to suction events due to the limited preload sensitivity of these devices. This may be of particular concern with rotary biventricular support (BiVAD) where the native, flow balancing Starling response is diminished in both ventricles. The reliability of sensor and sensorless-based control systems which aim to control VAD flow based on preload has limitations, and, thus, an alternative solution is desired. This study introduces a compliant inflow cannula (CIC) which could improve the preload sensitivity of a rotary VAD by passively altering VAD flow depending on preload. To evaluate the design, both the CIC and a standard rigid inflow cannula were inserted into a mock circulation loop to enable biventricular heart failure support using configurations of atrial and ventricular inflow, and arterial outflow cannulation. A range of left (LVAD) and right VAD (RVAD) rotational speeds were tested as well as step changes in systemic/pulmonary vascular resistance to alter relative preloads, with resulting flow rates recorded. Simulated suction events were observed, particularly at higher VAD speeds, during support with the rigid inflow cannula, while the CIC prevented suction events under all circumstances. The compliant section passively restricted its internal diameter as preload was reduced, which increased the VAD circuit resistance and thus reduced VAD flow. Therefore, a CIC could potentially be used as a passive control system to prevent suction events in rotary left, right, and biventricular support., (© 2012, Copyright the Authors. Artificial Organs © 2012, International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.)

The Exeter stems vary in length from 90 to 150 mm. The shorter stems generally have lower offsets. The purpose of this study was to determine if length of stem, with fixed offset, affected rotational stability. Mechanical testing was carried out on 10 implant-cement constructs with 2 loading profiles, rising from chair and stair climbing, at different simulated implant lengths using purpose-built apparatus. This paper presents a mechanism for clinically observed rotational stability and explains the mechanical characteristics required for rotational stability in Exeter femoral stems., (Copyright © 2012. Published by Elsevier Inc.)

Limited preload sensitivity of rotary left ventricular assist devices (LVADs) renders patients susceptible to harmful atrial or ventricular suction events. Active control systems may be used to rectify this problem; however, they usually depend on unreliable sensors or potentially inaccurate inferred data from, for example, motor current. This study aimed to characterize the performance of a collapsible inflow cannula reservoir as a passive control system to eliminate suction events in extracorporeal, rotary LVAD support. The reservoir was evaluated in a mock circulation loop against a rigid cannula under conditions of reduced preload and increased LVAD speed in both atrial and ventricular cannulation scenarios. Both cases demonstrated the ease with which chamber suction events can occur with a rigid cannula and confirm that the addition of the reservoir maintained positive chamber volumes with reduced preload and high LVAD speeds. Reservoir performance was dependent on height with respect to the cannulated chamber, with lower placement required in atrial cannulation due to reduced filling pressures. This study concluded that a collapsible inflow cannula is capable of minimizing suction events in extracorporeal, rotary LVAD support., (© 2011, Copyright the Authors. Artificial Organs © 2011, International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.)

In vitro cardiovascular device performance evaluation in a mock circulation loop (MCL) is a necessary step prior to in vivo testing. A MCL that accurately represents the physiology of the cardiovascular system accelerates the assessment of the device's ability to treat pathological conditions. To serve this purpose, a compact MCL measuring 600 × 600 × 600 mm (L × W × H) was constructed in conjunction with a computer mathematical simulation. This approach allowed the effective selection of physical loop characteristics, such as pneumatic drive parameters, to create pressure and flow, and pipe dimensions to replicate the resistance, compliance, and fluid inertia of the native cardiovascular system. The resulting five-element MCL reproduced the physiological hemodynamics of a healthy and failing heart by altering ventricle contractility, vascular resistance/compliance, heart rate, and vascular volume. The effects of interpatient anatomical variability, such as septal defects and valvular disease, were also assessed. Cardiovascular hemodynamic pressures (arterial, venous, atrial, ventricular), flows (systemic, bronchial, pulmonary), and volumes (ventricular, stroke) were analyzed in real time. The objective of this study is to describe the developmental stages of the compact MCL and demonstrate its value as a research tool for the accelerated development of cardiovascular devices., (© 2010, Copyright the Author. Artificial Organs © 2010, International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.)

Background: The development of a comprehensive and detailed model of the musculature of the lumbar region is required if biomechanical models are to accurately predict the forces and moments experienced by the lumbar spine., Methods: A new anatomical model representing the nine major muscles of the lumbar spine and the thoracolumbar fascia is presented. These nine muscles are modeled as numerous fascicles, each with its own force producing potential based on size and line of action. The simulated spine is fully deformable, allowing rotation in any direction, while respecting the physical constraints imposed by the skeletal structure. Maximal moments were predicted by implementing the model using a pseudo force distribution algorithm. Three types of surgery that affect the spinal musculature were simulated: posterior spinal surgery, anterior surgery, and total hip replacement., Findings: Predicted moments matched published data from maximum isometric exertions in male volunteers. The biomechanical changes for the three different types of surgery demonstrated several common features: decreased spinal compression and production of asymmetric moments during symmetric tasks., Interpretation: This type of analysis provides new opportunities to explore the effect of different patterns of muscle activity including muscle injury on the biomechanics of the spine., (Copyright © 2010 Elsevier Ltd. All rights reserved.)

Non-invasive vibration analysis has been used extensively to monitor the progression of dental implant healing and stabilization. It is now being considered as a method to monitor femoral implants in transfemoral amputees. This paper evaluates two modal analysis excitation methods and investigates their capabilities in detecting changes at the interface between the implant and the bone that occur during osseointegration. Excitation of bone-implant physical models with the electromagnetic shaker provided higher coherence values and a greater number of modes over the same frequency range when compared to the impact hammer. Differences were detected in the natural frequencies and fundamental mode shape of the model when the fit of the implant was altered in the bone. The ability to detect changes in the model dynamic properties demonstrates the potential of modal analysis in this application and warrants further investigation.

A review of the literature suggests that implanting current artificial discs for degenerative disc disease at one level of the lumbar spine is as safe and effective as fusion, but is not a substantially better procedure. There are no controlled trials of multilevel implantation, and the literature suggests that this should, therefore, be considered experimental surgery. There is evidence that adjacent levels are not protected from degeneration, and degeneration of the zygapophysial joints at the operated level may occur. The concept of motion preservation is unproven and needs to be reviewed.

The thoracolumbar fascia (TLF) provides a means of attachment to the lumbar spine for several muscles including the transverse abdominis, and parts of the latissimus dorsi and internal oblique muscles. Previous biomechanical models of the lumbar spine either tend to omit the TLF on the assumption that its contribution would be negligible or incorporate only part of the TLF. Here, a three-dimensional model of the posterior and middle layers of the TLF is presented to enable its action to be included in future three-dimensional models of the spine. It is used illustratively to estimate the biomechanical influence of this structure on the lumbar spine. The formulation of the model allows the lines of action of the fibres comprising the fascia to be calculated for any posture whilst ensuring that anatomical constraints are satisfied. Application of the model suggests that the TLF produces moments primarily in flexion and extension. The simulated results demonstrate that the abdominal muscles, acting via the TLF, are capable of contributing extension moments comparable to those produced by other smaller muscles associated with the lumbar spine., (Crown Copyright © 2010. Published by Elsevier Ltd. All rights reserved.)

Clinical studies have reported the balancing of pump outputs to be a serious control issue for rotary biventricular support (BiVS) systems. Poor reliability of long-term, blood immersed pressure sensors encouraged the development of a new control strategy to improve their viability. A rotary BiVS device was designed and constructed with a mechanical passive controller to autoregulate pump outputs to emulate the native baroreceptor response. In vitro testing in a dual circuit, hydraulic mock circulation loop showed that the prototype was able to maintain arterial pressures when subjected to sudden induced hemodynamic destabilization. However, inlet suction was observed when sudden simulated hypertension briefly reduced venous return to the cannulated ventricle. The results have encouraged further development of the device as a means to create an inherently stable, fully passive biventricular support device.

Recent studies into rotary biventricular support have indicated that inadequate left/right flow balancing may lead to vascular congestion and/or ventricular suckdown. The implementation of a passive controller that automatically adjusts left/right flow during total and partial cardiac support would improve physiological interaction. This has encouraged the development of a biventricular assist device (BiVAD) prototype that achieves passive control of the two rotary pumps' hydraulic output by way of a nonrotating double pressure plate configuration, the hub, suspended between the ventricular assist device (VAD) impellers. Fluctuations in either the VAD's inlet or outlet pressure will cause the hub to translate, and in doing so, affect each pump's hydraulic outputs. In order to achieve partial support, the floating assembly needed to respond to pathologic blood pressure signals while being insensitive to residual ventricular function. An incorporated mechanical spring-mass-damper assembly affects the passive response to optimize the dynamic interaction between the prototype and the supported cardiovascular system. It was found that increasing the damping from a medium to a high level was effective in filtering out the higher frequency ventricular pressure signals, reducing a modified amplitude ratio by up to 72%. A spring response was also identified as being inherent in the passive response and was characterized as being highly nonlinear at the extremes of the floating assembly's translation range. The results from this study introduce a new means of BiVAD control as well as the characterization of a fully passive mechanical physiological controller.

Generation of subject-specific finite element (FE) models from computed tomography (CT) datasets is of significance for application of the FE analysis to bone structures. A great challenge that remains is the automatic assignment of bone material properties from CT Hounsfield Units into finite element models. This paper proposes a new assignment approach, in which material properties are directly assigned to each integration point. Instead of modifying the dataset of FE models, the proposed approach divides the assignment procedure into two steps: generating the data file of the image intensity of a bone in a MATLAB program and reading the file into ABAQUS via user subroutines. Its accuracy has been validated by assigning the density of a bone phantom into a FE model. The proposed approach has been applied to the FE model of a sheep tibia and its applicability tested on a variety of element types. The proposed assignment approach is simple and illustrative. It can be easily modified to fit users' situations., (Copyright (c) 2009 Elsevier Ltd. All rights reserved.)

Analytical and computational models of the intervertebral disc (IVD) are commonly employed to enhance understanding of the biomechanics of the human spine and spinal motion segments. The accuracy of these models in predicting physiological behaviour of the spine is intrinsically reliant on the accuracy of the material constitutive representations employed to represent the spinal tissues. There is a paucity of detailed mechanical data describing the material response of the reinforced-ground matrix in the anulus fibrosus of the IVD. In the present study, the 'reinforced-ground matrix' was defined as the matrix with the collagen fibres embedded but not actively bearing axial load, thus incorporating the contribution of the fibre-fibre and fibre-matrix interactions. To determine mechanical parameters for the anulus ground matrix, mechanical tests were carried out on specimens of ovine anulus, under unconfined uniaxial compression, simple shear and biaxial compression. Test specimens of ovine anulus fibrosus were obtained with an adjacent layer of vertebral bone/cartilage on the superior and inferior specimen surface. Specimen geometry was such that there were no continuous collagen fibres coupling the two endplates. Samples were subdivided according to disc region - anterior, lateral and posterior - to determine the regional inhomogeneity in the anulus mechanical response. Specimens were loaded at a strain rate sufficient to avoid fluid outflow from the tissue and typical stress-strain responses under the initial load application and under repeated loading were determined for each of the three loading types. The response of the anulus tissue to the initial and repeated load cycles was significantly different for all load types, except biaxial compression in the anterior anulus. Since the maximum applied strain exceeded the damage strain for the tissue, experimental results for repeated loading reflected the mechanical ability of the tissue to carry load, subsequent to the initiation of damage. To our knowledge, this is the first study to provide experimental data describing the response of the 'reinforced-ground matrix' to biaxial compression. Additionally, it is novel in defining a study objective to determine the regionally inhomogeneous response of the 'reinforced-ground matrix' under an extensive range of loading conditions suitable for mechanical characterisation of the tissue. The results presented facilitate the development of more detailed and comprehensive constitutive descriptions for the large strain nonlinear elastic or hyperelastic response of the anulus ground matrix., (Copyright 2009 Elsevier Ltd. All rights reserved.)

The healing process for bone fractures is sensitive to mechanical stability and blood supply at the fracture site. Most currently available mechanobiological algorithms of bone healing are based solely on mechanical stimuli, while the explicit analysis of revascularization and its influences on the healing process have not been thoroughly investigated in the literature. In this paper, revascularization was described by two separate processes: angiogenesis and nutrition supply. The mathematical models for angiogenesis and nutrition supply have been proposed and integrated into an existing fuzzy algorithm of fracture healing. The computational algorithm of fracture healing, consisting of stress analysis, analyses of angiogenesis and nutrient supply, and tissue differentiation, has been tested on and compared with animal experimental results published previously. The simulation results showed that, for a small and medium-sized fracture gap, the nutrient supply is sufficient for bone healing, for a large fracture gap, non-union may be induced either by deficient nutrient supply or inadequate mechanical conditions. The comparisons with experimental results demonstrated that the improved computational algorithm is able to simulate a broad spectrum of fracture healing cases and to predict and explain delayed unions and non-union induced by large gap sizes and different mechanical conditions. The new algorithm will allow the simulation of more realistic clinical fracture healing cases with various fracture gaps and geometries and may be helpful to optimise implants and methods for fracture fixation.