Search

We demonstrate a technique allowing to develop a fully distributed optical fiber hot-wire anemometer capable of reaching a wind speed uncertainty of ≈ ±0.15m/s (±0.54km/h) at only 60 mW/m of dissipated power in the sensing fiber, and within only four minutes of measurement time. This corresponds to similar uncertainty values than previous papers on distributed optical fiber anemometry but requires two orders of magnitude smaller dissipated power and covers at least one order of magnitude longer distance. This breakthrough is possible thanks to the extreme temperature sensitivity and single-shot performance of chirped-pulse phase-sensitive optical time domain reflectometry (ΦOTDR), together with the availability of metal-coated fibers. To achieve these results, a modulated current is fed through the metal coating of the fiber, causing a modulated temperature variation of the fiber core due to Joule effect. The amplitude of this temperature modulation is strongly dependent on the wind speed at which the fiber is subject. Continuous monitoring of the temperature modulation along the fiber allows to determine the wind speed with singular low power injection requirements. Moreover, this procedure makes the system immune to temperature drifts of the fiber, potentially allowing for a simple field deployment. Being a much less power-hungry scheme, this method also allows for monitoring over much longer distances, in the orders of 10s of km. We expect that this system can have application in dynamic line rating and lateral wind monitoring in railway catenary wires.

Phase-sensitive optical time-domain reflectometry (φOTDR) is widely used for the distributed detection of mechanical or environmental variations with resolutions of typically a few meters. The spatial resolution of these distributed sensors is related to the temporal width of the input probe pulses. However, the input pulse width cannot be arbitrarily reduced (to improve the resolution), since a minimum pulse energy is required to achieve a good level of signal-to-noise ratio (SNR), and the pulse peak power is limited by the advent of nonlinear effects. In this Letter, inspired by chirped pulse amplification concepts, we present a novel technique that allows us to increase the SNR by several orders of magnitude in φOTDR-based sensors while reaching spatial resolutions in the centimeter range. In particular, we report an SNR increase of 20 dB over the traditional architecture, which is able to detect strain events with a spatial resolution of 1.8 cm.

This paper presents a novel surveillance system aimed at the detection and classification of threats in the vicinity of a long gas pipeline. The sensing system is based on phase-sensitive optical time domain reflectometry ( ϕ -OTDR) technology for signal acquisition and pattern recognition strategies for threat identification. The proposal incorporates contextual information at the feature level and applies a system combination strategy for pattern classification. The contextual information at the feature level is based on the tandem approach (using feature representations produced by discriminatively-trained multi-layer perceptrons) by employing feature vectors that spread different temporal contexts. The system combination strategy is based on a posterior combination of likelihoods computed from different pattern classification processes. The system operates in two different modes: (1) machine + activity identification, which recognizes the activity being carried out by a certain machine, and (2) threat detection, aimed at detecting threats no matter what the real activity being conducted is. In comparison with a previous system based on the same rigorous experimental setup, the results show that the system combination from the contextual feature information improves the results for each individual class in both operational modes, as well as the overall classification accuracy, with statistically-significant improvements.

Chemical sensing using optical fibers is often challenging, as it is generally difficult to achieve strong interaction between the guided light and the analyte at the wavelength of interest for performing the detection. Despite this difficulty, many schemes exist (and can be found in the literature) for point chemical fiber sensors. However, the challenge increases even further when it comes to performing fully distributed chemical sensing. In this case, the optical signal which interacts with the analyte is typically also the signal that has to travel to and from the interrogator: for a good sensitivity, the light should interact strongly with the analyte, leading inevitably to an increased loss and a reduced range. Few works in the literature actually provide demonstrations of truly distributed chemical sensing and, although there have been several attempts to realize these sensors (e.g. based on special fiber coatings), the vast majority of these attempts has failed to reach widespread use due to several reasons, among them: lack of sensitivity or selectivity, lack of range or resolution, cross sensitivity to temperature or strain, or need to work at specific wavelengths where fiber instrumentation becomes extremely expensive or unavailable. In this work we provide a preliminary demonstration of the possibility of achieving distributed detection of gas presence with spectroscopic selectivity, high spatial resolution, potential for long range measurements and feasibility of having most of the interrogator system working at conventional telecom wavelengths. For a full exploitation of this concept, new fibers (or more likely, fiber bundles) should be developed capable of guiding specific wavelengths in the IR (corresponding to gas absorption wavelengths) with good overlap with the analyte while also having a solid core with good transmission behavior at 1.55 μm, and good thermal coupling between the two guiding structures.

Typical phase-sensitive optical time-domain reflectometry (ϕOTDR) schemes rely on the use of coherent rectangular-shaped probe pulses. In these systems, there is a trade-off between the signal-to-noise ratio (SNR), spatial resolution, and operating range of the ϕOTDR system. To increase any of these parameters, an increase in the pulse peak power is usually indispensable. However, as it is well known, there is a limit in the allowable increase in probe power due to the onset of undesired nonlinear effects such as modulation instability. In this Letter, we perform an analysis of the effect of the probe pulse shape on the visibility fading due to modulation instability. In particular, four different temporal profiles are chosen: rectangular, Gaussian, triangular, and super-Gaussian (order 2). Our numerical and experimental analyses reveal that the use of triangular or Gaussian-like pulses can significantly inhibit the visibility fading issues. As such, an increase in the range up to twofold for the same pulse energy (i.e., SNR) and nominal spatial resolution can be achieved, as compared with the results obtained when using rectangular pulses. This is due to a more robust behavior of the Gaussian and triangular pulses against the Fermi-Pasta-Ulam recurrence occurring in modulation instability.

A simple, in-line method for real-time full characterization (amplitude and phase) of propagation distortions arising because of group velocity dispersion and self-phase modulation on 10-20 Gbps transmitted NRZ optical signals is reported. It is based on phase reconstruction using optical ultrafast differentiation (PROUD), a linear and self-referenced technique. The flexibility of the technique is demonstrated by characterizing different data stream scenarios. Experimental results were modeled using conventional propagation equations, showing good agreement with the measured data. It is envisaged that the proposed method could be used in combination with DSP techniques for the estimation and compensation of propagation distortions in fiber links, not only in conventional IM/DD systems, but also in coherent systems with advanced modulation formats.