Search

This article addresses the challenges presented by photoelectrochemical solar fuels technology in a discussion that begins with a functioning device and proceeds to the more fundamental science of its component parts. In this flow of discussion issues are addressed that frame the discussion for the next, increasingly more fundamental topic. The analysis begins with a discussion of the need for an analytical facility for confirmation of reported efficiencies of solar fuels device prototypes and then progressively narrows its scope to prototype design, the discovery of novel materials and the design of durable interfacial structures for fuels evolution. Molecular hydrogen will be considered first as the target fuel since many of the challenges with hydrogen production are general and applicable to the more complex CO2 reduction, which will be treated as a supplementary subject.

We report the application of a Pictet-Spengler reaction to the synthesis of covalent organic frameworks (COFs) using functionalized terephthalaldehydes. The COFs produced show an increased propensity to generate screw dislocations and produce multilayered flakes when compared with other 2D-COFs. Using HRTEM, definitive evidence for screw dislocations was obtained and is presented. The effects on separations using these materials in membranes are also reported.

Functionalizing graphene with exact pore size, specific functional groups, and precision doping poses many significant challenges. Current methods lack precision and produce random pore sizes, sites of attachment, and amounts of dopant, leading to compromised structural integrity and affecting graphene's applications. In this work, we report a strategy for the synthesis of functionalized graphitic materials with modifiable nanometer-sized pores via a Pictet-Spengler polymerization reaction. This one-pot, four-step synthesis uses concepts based on covalent organic frameworks (COFs) synthesis to produce crystalline two-dimensional materials that were confirmed by PXRD, TEM measurements, and DFT studies. These new materials are structurally analogous to doped graphene and graphene oxide (GO) but, unlike GO, maintain their semiconductive properties when fully functionalized.

Two-dimensional covalent organic frameworks (2D-COFs) exhibit characteristics ideal for membrane applications, such as high stability, tunability and porosity along with well-ordered nanopores. However, one of the many challenges with fabricating these materials into membranes is that membrane wetting can result in layer swelling. This allows molecules that would be excluded based on pore size to flow around the layers of the COF, resulting in reduced separation. Cross-linking between these layers inhibits swelling to improve the selectivity of these membranes. In this work, computational models were generated for a quinoxaline-based COF cross-linked with oxalyl chloride (OC) and hexafluoroglutaryl chloride (HFG). Enthalpy of formation and cohesive energy calculations from these models show that formation of these COFs is thermodynamically favorable and the resulting materials are stable. The cross-linked COF with HFG was synthesized and characterized with Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis with differential scanning calorimetry (TGA-DSC), and water contact angles. Additionally, these frameworks were fabricated into membranes for permeance testing. The experimental data supports the presence of cross-linking and demonstrates that varying the amount of HFG used in the reaction does not change the amount of cross-linking present. Computational models indicate that varying the cross-linking concentration has a negligible effect on stability and less cross-linking still results in stable materials. This work sheds light on the nature of the cross-linking in these 2D-COFs and their application in membrane technologies.

We report a new synthetic protocol for preparing highly ordered two-dimensional nanoporous covalent organic frameworks (2D-COFs) based on a quinoxaline backbone. The quinoxaline framework represents a new type of COF that enables postsynthetic modification by placing two different chemical functionalities within the nanopores including layer-to-layer cross-linking. We also demonstrate that membranes fabricated using this new 2D-COF perform highly selective separations resulting in dramatic performance enhancement post cross-linking.

Two-dimensional covalent organic frameworks (2D-COFs) have been of increasing interest in the past decade due to their porous structures that ideally can be highly ordered. One of the most common routes to these polymers relies on Schiff-base chemistry, i.e., the condensation reaction between a carbonyl and an amine. In this report, we elaborate on the condensation of 3,6-dibromobenzene-1,2,4,5-tetraamine with hexaketocyclohexane (HKH) and the subsequent carbonylation of the resulting COF, along with the possibility that the condensation reaction on HKH can result in a trans configuration resulting in the formation of a disordered 2D-COF. This strategy enables modification of COFs via bromine substitution reactions to place functional groups within the pores of the materials. Ion-sieving measurements using membranes from this COF, reaction of small molecules with unreacted keto groups along with modeling studies indicate disorder in the COF polymerization process. We also present a Monte Carlo simulation that demonstrates the influence of even small amounts of disorder upon both the 2D and 3D structure of the resulting COF.

Vertical van der Waals (vdW) heterostructures of 2D crystals with defined interlayer twist are of interest for band-structure engineering via twist moiré superlattice potentials. To date, twist-heterostructures have been realized by micromechanical stacking. Direct synthesis is hindered by the tendency toward equilibrium stacking without interlayer twist. Here, we demonstrate that growing a 2D crystal with fixed azimuthal alignment to the substrate followed by transformation of this intermediate enables a potentially scalable synthesis of twisted heterostructures. Microscopy during growth of ultrathin orthorhombic SnS on trigonal SnS 2 shows that vdW epitaxy yields azimuthal order even for non-isotypic 2D crystals. Excess sulfur drives a spontaneous transformation of the few-layer SnS to SnS 2 , whose orientation - rotated 30° against the underlying SnS 2 crystal - is defined by the SnS intermediate rather than the substrate. Preferential nucleation of additional SnS on such twisted domains repeats the process, promising the realization of complex twisted stacks by bottom-up synthesis.

The spectral sensitization of single-crystal p-GaP by semiconducting single-walled carbon nanotubes (s-SWCNT) via hole injection into the p-GaP valence band is reported. The results are compared to SWNCT sensitized n-type single-crystal substrates: TiO 2 , SnO 2 , and n-GaP. It was found that the sensitized photocurrents from CoMoCAT and HiPco s-SWCNTs were from a hole injection mechanism on all substrates, even when electron injection into the conduction band should be energetically favored. The results suggest an intrinsic p-type character of the s-SWCNTs surface films investigated in this work.

Dye-sensitized solar cells have been studied for many years as a potential inexpensive and scalable alternative to silicon solar cells. They have recently expanded their list of photosensitizers to include quantum dots. In recent years, there has been substantial progress in the field of quantum dot solar cells, with certified efficiencies now reaching 13.4%. Fundamental studies on nanomaterial/semiconductor electrode coupling have led to a deeper understanding of photoinduced electron-transfer processes that are important for both of these devices. This Feature Article will highlight the use of a model system, nanomaterials sensitizing single-crystal oxide substrates, that is useful for investigating how changes in nanomaterial shape, dimensionality, size, and local environment affect the photoinduced charge separation efficiency.

The preparation of membranes with high selectivity based on specific chemical properties such as size and charge would impact the efficiency of the world's energy supply, the production of clean water, and many other separation technologies. We report a flexible synthetic protocol for preparing highly ordered two-dimensional nanoporous polymeric materials (termed covalent organic frameworks or COFs) that allow for placing virtually any function group within the nanopores. We demonstrate that membranes, fabricated with this new family of materials with carboxylated pore walls, are very water permeable, as well as highly charged and size selective.

Semiconducting single-walled carbon nanotubes' (SWCNTs) broad absorption range and all-carbon composition make them attractive materials for light harvesting. We report photoinduced charge transfer from both multichiral and single-chirality SWCNT films into atomically flat SnO 2 and TiO 2 crystals. Higher-energy second excitonic SWCNT transitions produce more photocurrent, demonstrating carrier injection rates are competitive with fast hot-exciton relaxation processes. A logarithmic relationship exists between photoinduced electron-transfer driving force and photocarrier collection efficiency, becoming more efficient with smaller diameter SWCNTs. Photocurrents are generated from both conventional sensitization and in the opposite direction with the semiconductor under accumulation and acting as an ohmic contact with only the p-type nanotubes. Finally, we demonstrate that SWCNT surfactant choice and concentration play a large role in photon conversion efficiency and present methods of maximizing photocurrent yields.

Interfaces combining polydopamine (PDA) and nanoparticles have been widely utilized for fabricating hybrid colloidal particles, thin films, and membranes for applications spanning biosensing, drug delivery, heavy metal detection, antifouling membranes, and lithium ion batteries. However, fundamental understanding of the interaction between PDA and nanoparticles is still limited, especially the impact of PDA on nanoparticle nucleation and growth. In this work, PDA is used to generate functional bonding sites for depositing titanium dioxide (TiO 2 ) via atomic layer deposition (ALD) onto a nanoporous polymer substrate for a range of ALD cycles (<100). The resulting hybrid membranes are systematically characterized using water contact angle, scanning electron microscopy, atomic force microscopy, nitrogen adsorption and desorption, and X-ray photoelectron spectroscopy (XPS). An intriguing nonlinear relationship was observed between the number of ALD cycles and changes in surface properties (water contact angle and surface roughness). Together with XPS study, those changes in surface properties were exploited to probe the nanoparticle nucleation and growth process on complex PDA-coated porous polymer substrates. Molecular level understanding of inorganic and polymer material interfaces will shed light on fine-tuning nanoparticle-modified polymeric membrane materials., Competing Interests: The authors declare no competing financial interest.

We report the synthesis of ultrathin silver sulfide (Ag 2 S) nanoplatelets (NPLs) synthesized via a one-pot method in ethylene glycol with 3-mercaptopropionic acid serving as both the sulfur precursor and the platelet ligand. The colloidally synthesized nanoplatelets are exceptionally thin, with a thickness of only 3.5 ± 0.2 Å and a 1S exciton Bohr diameter to confinement ratio of ∼12.6. The NPL growth is shown to be quantized by layer thickness using absorption and photoluminescence (PL) spectroscopy. Transmission electron microscopy, atomic force microscopy, and X-ray diffraction analyses of the NPLs show that they correspond to the (202) plane of the β-Ag 2 S structure. The PL quantum yield of these NPLs is ∼30%, suggesting their potential use in biomedical imaging. Optoelectronic properties were evaluated via sensitized photocurrent spectroscopy with the resulting spectra closely matching the distinctive absorption spectral shape of the Ag 2 S NPLs.

Cyanine dyes, often used in dye-sensitized solar cells (DSSCs), form a range of molecular species from monomers to large H and J aggregates in both solution and when adsorbed at a photoelectrode surface. To determine the relative capability of the different dye species to inject photoexcited electrons into a wideband gap oxide semiconductor, sensitization at a single-crystal zinc oxide surface was studied by simultaneous attenuated reflection (ATR) ultraviolet-visible (UV-vis) absorption and photocurrent spectroscopy measurements. ATR measurements enable identification of the dye species populating the surface with simultaneous photocurrent spectroscopy to identify the contribution of the various dye forms to photocurrent signal. We study the dye 2,2'-carboxymethylthiodicarbocyanine bromide that is particularly prone to aggregation both in solution and at the surface of sensitized oxide semiconductors.

Lead selenide (PbSe) quantum dots (QDs) are an attractive material for application in photovoltaic devices due to the ability to tune their band gap, efficient multiple exciton generation, and high extinction coefficients. However, PbSe QDs are quite unstable to oxidation in air. Recently there have been multiple studies detailing postsynthetic halide treatments to stabilize lead chalcogenide QDs. We exploit iodide-stabilized PbSe QDs in a model QD-sensitized solar cell configuration where zinc oxide (ZnO) single crystals are sensitized using cysteine as a bifunctional linker molecule. Sensitized photocurrents stable for >1 h can be measured in aqueous KI electrolyte that is usually corrosive to QDs under illumination. The spectral response of the sensitization extended out to 1700 nm, the farthest into the infrared yet observed. Hints of the existence of multiple exciton generation and collection as photocurrent, as would be expected in this system, are speculated and discussed.

A sol-gel method for the synthesis of semiconducting FeCrAl oxide photocathodes for solar-driven hydrogen production was developed and applied for the production of meso- and macroporous layers with the overall stoichiometry Fe0.84Cr1.0Al0.16O3. Using transmission electron microscopy and energy-dispersive X-ray spectroscopy, phase separation into Fe- and Cr-rich phases was observed for both morphologies. Compared to prior work and to the mesoporous layer, the macroporous FeCrAl oxide photocathode had a significantly enhanced photoelectrolysis performance, even at a very early onset potential of 1.1 V vs RHE. By optimizing the macroporous electrodes, the device reached current densities of up to 0.68 mA cm(-2) at 0.5 V vs RHE under AM 1.5 with an incident photon-to-current efficiency (IPCE) of 28% at 400 nm without the use of catalysts. Based on transient measurements, this performance increase could be attributed to an improved collection efficiency. At a potential of 0.75 V vs RHE, an electron transfer efficiency of 48.5% was determined.

High-throughput combinatorial methods have been useful in identifying new oxide semiconductors with the potential to be applied to solar water splitting. Most of these techniques have been limited to producing and screening oxide phases formed at temperatures below approximately 550 °C. We report the development of a combinatorial approach to discover and optimize high temperature phases for photoelectrochemical water splitting. As a demonstration material, we chose to produce thin films of high temperature CuNb oxide phases by inkjet printing on two different substrates: fluorine-doped tin oxide and crystalline Si, which required different sample pyrolysis procedures. The selection of pyrolysis parameters, such as temperature/time programs, and the use of oxidizing, nonreactive or reducing atmospheres determines the composition of the thin film materials and their photoelectrochemical performance. XPS, XRD, and SEM analyses were used to determine the composition and oxidation states within the copper niobium oxide phases and to then guide the production of target Cu(1+)Nb(5+)-oxide phases. The charge carrier dynamics of the thin films produced by the inkjet printing are compared with pure CuNbO3 microcrystalline material obtained from inorganic bulk synthesis.

The doping density dependence of photocurrents has been experimentally measured at single crystal rutile TiO2 electrodes sensitized with the N3 chromophore and a trimethine dye. As the doping density of the electrodes was varied from 10(15) to 10(20) cm(-3), three different regimes of behavior were observed for the magnitude and shape of the dye sensitized current-voltage curves. Low-doped crystals produced current-voltage curves with a slow rise of photocurrent with potential. At intermediate doping levels, Schottky barrier behavior was observed producing a photocurrent plateau at electrode bias in the depletion region. At highly doped electrodes, tunneling currents played a significant role especially in the recombination processes. These different forms of the current-voltage curves could be fit to an Onsager-based model for charge collection at a semiconductor electrode. The fitting revealed the role of the various physical parameters that govern photoinduced charge collection in sensitized systems.

A high-throughput thin film materials library for Fe-Cr-Al-O was obtained by reactive magnetron cosputtering and analyzed with automated EDX and XRD to elucidate compositional and structural properties. An automated optical scanning droplet cell was then used to perform photoelectrochemical measurements of 289 compositions on the library, including electrochemical stability, potentiodynamic photocurrents and photocurrent spectroscopy. The photocurrent onset and open circuit potentials of two semiconductor compositions (n-type semiconducting: Fe51Cr47Al2Ox, p-type semiconducting Fe36.5Cr55.5Al8Ox) are favorable for water splitting. Cathodic photocurrents are observed at 1.0 V vs RHE for the p-type material exhibiting an open circuit potential of 0.85 V vs RHE. The n-type material shows an onset of photocurrents at 0.75 V and an open circuit potential of 0.6 V. The p-type material showed a bandgap of 1.55 eV, while the n-type material showed a bandgap of 1.97 eV.

Layered metal dichalcogenides have attracted significant interest as a family of single- and few-layer materials that show new physics and are of interest for device applications. Here, we report a comprehensive characterization of the properties of tin disulfide (SnS2), an emerging semiconducting metal dichalcogenide, down to the monolayer limit. Using flakes exfoliated from layered bulk crystals, we establish the characteristics of single- and few-layer SnS2 in optical and atomic force microscopy, Raman spectroscopy and transmission electron microscopy. Band structure measurements in conjunction with ab initio calculations and photoluminescence spectroscopy show that SnS2 is an indirect bandgap semiconductor over the entire thickness range from bulk to single-layer. Field effect transport in SnS2 supported by SiO2/Si suggests predominant scattering by centers at the support interface. Ultrathin transistors show on-off current ratios >10(6), as well as carrier mobilities up to 230 cm(2)/(V s), minimal hysteresis, and near-ideal subthreshold swing for devices screened by a high-k (deionized water) top gate. SnS2 transistors are efficient photodetectors but, similar to other metal dichalcogenides, show a relatively slow response to pulsed irradiation, likely due to adsorbate-induced long-lived extrinsic trap states.

CdSe quantum dots (QDs) were attached to single crystal ZnO(0001) and ZnO(1100) substrates using capping groups, 4-mercaptobenzoic acid, 2-mercaptoacetic acid, 3-mercaptopropionic acid, 8-mercaptooctanoic acid, and 11-mercaptoundecanoic acid, as bifunctional linker molecules. The spectral response and photosensitization yields of the adsorbed QDs were studied with photocurrent spectroscopy. Atomic force microscopy (AFM) was used to verify the surface structure of the ZnO crystals and to examine the coverage and arrangement of the QDs on the single crystal surface. The inner-sphere aqueous redox couple Sx(2-)/S(2-), often used as a regenerator for chalcogenide-based QDs, as well as outer-sphere redox couples such as ferrocene, were able to regenerate the photoexcited CdSe QDs and suppress their photocorrosion. Differences in the binding of the QDs to different ZnO crystal faces are also reported.

The electrogenerated chemiluminescence (ECL) of a carbazole thiophene cyanoacrylate dye ((2-cyano-3-[5"'-(9-ethyl-9H-carbazol-3-yl)-3',3",3"',4-tetra-n-hexyl-[2,2',5',2",5",2"']-quarter-thiophenyl-5yl]acrylate) = MK-2) has been investigated in solution, where the maximum ECL wavelength occurs at 640 nm, and in a thin film on an ITO surface, where the ECL is substantially red-shifted to 730 nm. The ECL intensity for the solution annihilation reaction is relatively weak, whereas a much higher ECL intensity is measured with oxalate as a co-reactant. This result is attributed to the two Nernstian reversible oxidation waves of the thiophene moiety of MK-2, whereas the reduction is stabilized by the unblocked carbazole and cyanoacrylate groups.

Carbon interdigitated array (IDA) electrodes with features sizes down to 1.2 μm were fabricated by controlled pyrolysis of patterned photoresist. Cyclic voltammetry of reversible redox species produced the expected steady-state currents. The collection efficiency depends on the IDA electrode spacing, which ranged from around 2.7 to 16.5 μm, with the smaller dimensions achieving higher collection efficiencies of up to 98%. The signal amplification because of redox cycling makes it possible to detect species at relatively low concentrations (10(-5) molar) and the small spacing allows detection of transient electrogenerated species with much shorter lifetimes (submillisecond). Digital simulation software that accounts for both the width and height of electrode elements as well as the electrode spacing was developed to model the IDA electrode response. The simulations are in quantitative agreement with experimental data for both a simple fast one electron redox reaction and an electron transfer with a following chemical reaction at the IDAs with larger gaps whereas currents measured for the smallest IDA electrodes, that were larger than the simulated currents, are attributed to convection from induced charge electrokinetic flow.

Homoepitaxial growth of highly ordered and pure layers of rutile on rutile crystal substrates and anatase on anatase crystal substrates using atomic layer deposition (ALD) is reported. The epilayers grow in a layer-by-layer fashion at low deposition temperatures but are still not well ordered on rutile. Subsequent annealing at higher temperatures produces highly ordered, terraced rutile surfaces that in many cases have fewer electrically active defects than the substrate crystal. The anatase epitaxial layers, grown at 250 °C, have much fewer electrically active defects than the rather impure bulk crystals. Annealing the epilayers at higher temperatures increased band gap photocurrents in both anatase and rutile.

We report the identification of a semiconducting p-type oxide containing iron, aluminum, and chromium (Fe2-x-yCrxAlyO3) with previously unreported photoelectrolysis activity that was discovered by an undergraduate scientist participating in the Solar Hydrogen Activity research Kit (SHArK) program. The SHArK program is a distributed combinatorial science outreach program designed to provide a simple and inexpensive way for high school and undergraduate students to participate in the search for metal oxide materials that are active for the photoelectrolysis of water. The identified Fe2-x-yCrxAlyO3 photoelectrolysis material possesses many properties that make it a promising candidate for further optimization for potential application in a photoelectrolysis device. In addition to being composed of earth abundant elements, the FeCrAl oxide material has a band gap of 1.8 eV. Current-potential measurements for Fe2-x-yCrxAlyO3 showed an open circuit photovoltage of nearly 1 V; however, the absorbed photon conversion efficiency for hydrogen evolution was low (2.4 × 10(-4) at 530 nm) albeit without any deposited hydrogen evolution catalyst. X-ray diffraction of the pyrolyzed polycrystalline thin Fe2-x-yCrxAlyO3 film on fluorine-doped tin oxide substrates shows a hexagonal phase (hematite structure) and scanning electron microscope images show morphology consisting of small crystallites.

The photoelectrochemical behavior of materials based on binary Bi-V oxides was investigated by preparing libraries of ternary metal oxides using high-throughput combinatorial inkjet printing of oxide precursors onto conductive glass substrates. Subsequent pyrolysis of the printed films, with addition of various levels of a third metal oxide precursor, produced libraries of metal oxides that were immersed under potential control into an electrolyte solution and evaluated for water photooxidation or photoreduction activity using a laser scanning technique to produce photocurrent images. It was found that the photoelectrolysis activity of the Bi-V oxides of various stoichiometries was best at a Bi/V ratio of 1 to 1 or the BiVO4 phase. The photocurrent generation of this phase was improved by the addition of various amounts of W, Cu, Fe, Mg, and Mn. Addition of W led to the largest increase in photocurrent of up to 18 times; however the electronic band gap was increased compared to that of unsubstituted BiVO4.

It is often assumed that the photoresponse or incident photon-to-current conversion efficiency (IPCE) spectrum of a sensitized semiconductor electrode is directly correlated with the amount of sensitizing species present on the semiconductor surface. In reality, the various forms of adsorbed species, such as dye aggregates or dye molecules bound to different adsorption sites, such as terrace edges, can have significantly different electron injection yields and carrier recombination rates. To provide information about the amounts of the various adsorbed dye species and their effectiveness as sensitizers, we report the simultaneous acquisition of IPCE and attenuated total reflectance (ATR) UV-vis spectra for a thiacyanine dye bound to a single-crystal oxide semiconductor electrode surface. ZnO single crystals were fashioned into internal-reflection elements to act both as a waveguide for the internally reflected probe beam for UV-vis spectra and as the substrate for dye sensitization using dyes with distinct spectral signatures for monomers and aggregates. Strong agreement was observed between the quantum efficiency and ATR UV-vis spectra, suggesting that, under the conditions employed, both monomers and aggregates of the dye studied generate photocurrent with the same efficiency.

Four dicarboxylated cyanine dyes were used to sensitize single-crystal anatase (001), anatase (101), rutile (001), and rutile (100) surfaces. Incident photon to current efficiencies (IPCE) spectra and isotherms were gathered for the different combination of dyes and surfaces. The maximum coverage of the surface-bound dyes on the TiO2 crystal surfaces was determined by photochronocoulometric measurements. The IPCE spectra of the surface-bound dyes revealed that both the dye monomers and H-aggregates were both present and generated photocurrent. The relative abundance of dye monomers and H-aggregates was found to be strongly dependent on the crystallographic face used as the substrate for sensitization. The ratio of dye monomer to H-aggregate was quantified by fitting the IPCE spectra with a sum of the dye monomer and H-aggregate solution spectra. The trends in surface coverage were explained using a simple "lattice matching" model where the distance between the coordinatively unsaturated Ti binding sites on the various TiO2 crystallographic surfaces was compared with the distance between the carboxylate groups on the dyes. The rutile (100) surface had the highest coverage for all the dyes in agreement with the predictions of the lattice-matching model. Absorbed photon-to-current-efficiencies (APCEs) were calculated from the incident photon current efficiencies, the extinction coefficients and the measured surface coverages. The factors that affect the APCE values such as the relative injection yield for monomers and aggregate, the relative surface coverage values for monomers and aggregates, and semiconductor doping levels are discussed.

Dye sensitization of zinc oxide single crystals by a carbazole thiophene cyanoacrylate (MK-2) sensitizer deposited from THF and mixtures of THF and water was investigated. AFM images show the formation of larger aggregates, with the maximum size of 20-30 nm from mixtures of THF and water, compared with 8-12 nm from pure THF. Sensitized photocurrent spectra were correlated with the morphological results from AFM imaging and indicate that aggregation in water results in less efficient sensitization of the ZnO substrate. The presence of the aggregation in solution due to water content was confirmed by absorbance and fluorescence spectroscopies.

Interdigitated array electrodes (IDAs) were used to produce steady-state electrogenerated chemiluminescence (ECL) by annihilation of oxidized and reduced forms of a substituted boron dipyrromethene (BODIPY) dye, 9,10-diphenylanthracene (DPA), and ruthenium(II) tris(bypiridine) (Ru(bpy)3(2+)). Digital simulations were in good agreement with the experimentally obtained currents and light outputs. Coreactant experiments, using tri-n-propylamine and benzoyl peroxide as a sacrificial homogeneous reductant or oxidant, show currents corresponding to electrode reactions of the dyes and not the oxidation or reduction of the coreactants. The results show that interdigitated arrays can produce stable ECL where the light intensity is magnified due to the larger currents as a consequence of feedback between generator and collector electrodes in the IDA. The light output for ECL is around 100 times higher than that obtained with regular planar electrodes with similar area.

A library of electrocatalysts for water electrolysis under acidic conditions was created by ink jet printing metal oxide precursors followed by pyrolysis in air to produce mixed metal oxides. The compositions were then screened in acidic electrolytes using a pH sensitive fluorescence indicator that became fluorescent due to the pH change at the electrode surface because of the release of protons from water oxidation. The most promising materials were further characterized by measuring polarization curves and Tafel slopes as anodes for water oxidation. Mixed metal oxides that perform better than the iridium oxide standard were identified.

Comparison of the UV-vis absorption spectra of CdSe quantum dots (QDs) capped with various mercaptocarboxylic acid capping ligands reveals that only 4-mercaptobenzoic acid (MBzA) capping ligands lower the apparent optical band gap. We propose that the delocalization of the excitons in the CdSe QDs is extended onto the ligands via electronic coupling to the π system of the 4-mercaptobenzoic acid molecules through the Cd-S bond. Furthermore, we demonstrate that the electronic coupling between the QDs and the (MBzA) thiol ligands is influenced by the strength of the Cd-S bond that can be changed by protonating the S atom.

We show that highly oxidizing valence band holes, produced by ultraviolet (UV) illumination of naturally occurring semiconducting minerals, are capable of oxidizing chloride ion to perchlorate in aqueous solutions at higher rates than other known natural perchlorate production processes. Our results support an alternative to atmospheric reactions leading to the formation of high concentrations of perchlorate on Mars.

Nanocrystals of multicomponent chalcogenides, such as Cu(2)ZnSnS(4) (CZTS), are potential building blocks for low-cost thin-film photovoltaics (PVs). CZTS PV devices with modest efficiencies have been realized through postdeposition annealing at high temperatures in Se vapor. However, little is known about the precise role of Se in the CZTS system. We report the direct solution-phase synthesis and characterization of Cu(2)ZnSn(S(1-x)Se(x))(4) nanocrystals (0 ≤ x ≤ 1) with the aim of probing the role of Se incorporation into CZTS. Our results indicate that increasing the amount of Se increases the lattice parameters, slightly decreases the band gap, and most importantly increases the electrical conductivity of the nanocrystals without a need for annealing.

The nanoscale morphology and photoactivity of conjugated polyelectrolytes (CPEs) deposited from different solvents onto single crystal TiO(2) were investigated with atomic force microscopy (AFM) and photocurrent spectroscopy. CPE surface coverages on TiO(2) could be incremenentally increased by adsorbing the CPEs from static solutions. The solvents used for polymer adsorption influenced the surface morpohology of the CPEs on the TiO(2) surface. Photocurrent spectroscopy measurements in aqueous electrolytes, using iodide as a hole scavenger, revealed that the magnitude of the sensitized photocurrents was related to the surface coverages and the degree of aggregation of the CPEs as determined by AFM imaging. Absorbed photon-to-current efficiencies approaching 50% were measured for CPE layers as thick as 4 nm on TiO(2). These results suggest that precise control of CPE morphology at the TiO(2) interface can be achieved through optimization of the deposition conditions to improve the power conversion efficiencies of polymer-sensitized solar cells., (© 2011 American Chemical Society)

The nature of the chemical bonding of a pentacene molecule to a gold surface is studied. The calculations are carried out using two very different methodologies, the ab inito gaussian molecular orbital method and a numerical atomic orbital method, developed from the well tested SIESTA approach. Using the GAUSSIAN 09 package, we employ both local density B3LYP, and long-range correlated functionals CAM-B3LYP, ωB97, and ωB97X. For comparison, we also calculate the adsorption energy using the ATOMISTIX TOOLKIT with the revised PBE functional. Within computational and experimental errors we find that the best description of the binding energies can be obtained from GAUSSIAN calculations using long-range ωB97 and ωB97X exchange functionals. Thus the nature of chemical bonding of a pentacene to gold is a van der Waals type. To understand the large variation in the geometries computed by different methods, we calculate energy profiles in both X- and Y-directions. The energy barriers appear to be very small and comparable with the value of room temperature. Thus a pentacene molecule moves on a gold surface with almost no friction at room temperatures. An estimation of the work function is often obtained from a simple electrostatic approach. We test this estimation and find that this approach cannot be used because it significantly underestimates the work function. This investigation gives insights into the structure and bonding of pentacene to a gold surface and provides ideas for the improvement of methodologies for computing the properties of van der Waals adsorbates.

The effect of adding small amounts of Ti, Si, and Al on the photoelectrochemical activity of α-Fe(2)O(3) is investigated using a high-throughput combinatorial method. Quantitative ink jet printing is used to pattern iron oxide and dopant precursors onto conductive glass substrates. Subsequent pyrolysis yields a library of doped iron oxide electrodes that are screened for photoelectrolysis activity by immersing in an electrolyte and scanning a laser over the electrodes to map the photocurrent response. When Si and Al are individually added to iron oxide at the levels we studied, the photoelectrolysis activity decreased whereas low levels of Ti addition enhanced the photocurrents. Synergistic effects were observed resulting in enhanced photocurrents when multiple impurities were added to α-Fe(2)O(3).

Cu₂ZnSnS₄ (CZTS) nanocrystals, synthesized by a hot injection solution method, have been fabricated into thin films by dip-casting onto fluorine doped tin oxide (FTO) substrates. The photoresponse of the CZTS nanocrystal films was evaluated using absorbance measurements along with photoelectrochemical methods in aqueous electrolytes. Photoelectrochemical characterization revealed a p-type photoresponse when the films were illuminated in an aqueous Eu(3+) redox electrolyte. The effects of CZTS stoichiometry, film thickness, and low-temperature annealing on the photocurrents from front and back illumination suggest that the minority carrier diffusion and recombination at the back contact (via reaction of photogenerated holes with Eu(2+) produced from photoreduction by minority carriers) are the main loss mechanisms in the cell. Low-temperature annealing resulted in significant increases in the photocurrents for films made from both Zn-rich and stoichiometric CZTS nanocrystals.

Multiple exciton generation, the creation of two electron-hole pairs from one high-energy photon, is well established in bulk semiconductors, but assessments of the efficiency of this effect remain controversial in quantum-confined systems like semiconductor nanocrystals. We used a photoelectrochemical system composed of PbS nanocrystals chemically bound to TiO(2) single crystals to demonstrate the collection of photocurrents with quantum yields greater than one electron per photon. The strong electronic coupling and favorable energy level alignment between PbS nanocrystals and bulk TiO(2) facilitate extraction of multiple excitons more quickly than they recombine, as well as collection of hot electrons from higher quantum dot excited states. Our results have implications for increasing the efficiency of photovoltaic devices by avoiding losses resulting from the thermalization of photogenerated carriers.

Sensitization of mesoporous nanocrystalline TiO(2) solar cells with quantum confined semiconductor nanocrystals (QDs) has some advantages over organic dyes or inorganic complex sensitizers, yet the reported efficiencies of laboratory devices are not currently competitive with those of dye sensitized cells. Several methods previously utilized to bind CdSe QDs to mesoporous TiO(2) films were investigated using low index faces of both anatase and rutile TiO(2) polytypes as model systems. The in situ ligand exchange method, where 3-mercaptopropionic acid (MPA) covered TiO(2) crystal surfaces are treated with trioctylphosphine (TOP)/trioctylphosphine oxide (TOPO) (TOP/TOPO)-capped CdSe QDs, resulted in very irreproducible and usually low sensitized photocurrents. The ex situ ligand exchange method, whereby MPA-capped QDs are synthesized and directly adsorbed onto bare TiO(2) single crystals, resulted in both reproducible sensitized photocurrents and surface coverages that are verified with atomic force microscopy (AFM). Purification of the nanocrystals and adjustment of the pH of the sensitization solution to >10.2 was found to prevent QD agglomeration and takes advantage of the dual chemical functionality of MPA to directly link the QDs to the TiO(2) surface. The spectral response of the incident photon to current efficiencies of CdSe QDs was directly compared to the commonly used sensitizer cis-di(thiocyanato)-bis(4,4;-dicarboxy-2,2'-bipyridine)ruthenium(II) (N3) on the same single crystals.

Quantum dots (QDs) are actively explored as alternative sensitizers to inorganic complexes in sensitized solar cells (SSC) due to their interesting physical, optical, and electronic properties. It is thought that the inorganic nature of QDs should provide enhanced stability over the entirely organic or inorganic complex dyes, yet the long-term stability of laboratory QD-SSC devices has not been investigated in detail. A general approach to synthesize high stability QDs involves coating the core material with a wide band gap inorganic shell material (type-I CS QD). However, the electronic structure of the resulting core/shell (CS) structure has potential barriers for both electron and hole transfer, suggesting inefficient charge carrier separation for type-I CS QDs. Herein we demonstrate that type-I CdSe/ZnS CS QDs can effectively sensitize single crystal TiO(2) electrodes and continue to operate in a regenerative mode in an aerated iodide electrolyte for more than 20 h. Core CdSe QDs degrade rapidly in the same electrolyte presumably due to CdI(2) formation. The possibility of exploring new core/shell nanomaterials in a variety of electrolyte/mediator combinations may result in more efficient and stable QD-SSCs.

Even though investigations of dye-sensitized nanocrystalline semiconductors in solar cells has dominated research on dye-sensitized semiconductors over the past two decades, single crystal electrodes represent far simpler model systems for studying the sensitization process with a continuing train of studies dating back more than 40 years. Even today single crystal surfaces prove to be more controlled experimental models for the study of dye-sensitized semiconductors than the nanocrystalline substrates. This Account analyzes the scientific advances in the model sensitized single crystal systems that preceded the introduction of nanocrystalline semiconductor electrodes. It then follows the single crystal research to the present, illustrating both their striking simplicity of use and clarity of interpretation relative to nanocrystalline electrodes. Researchers have employed many electrochemical, photochemical, and scanning probe techniques for studying monolayer quantities of sensitizing dyes at specific crystallographic faces of different semiconductors. These methods include photochronocoulometry, electronic spectroscopy, and flash photolysis of dyes at potential-controlled semiconductor electrodes and the use of total internal reflection methods. In addition, we describe the preparation of surfaces of single crystal SnS(2) and TiO(2) electrodes to serve as reproducible model systems for charge separation at dye-sensitized solar cells. This process involves cleaving the SnS(2) electrodes and a photoelectrochemical surface treatment for TiO(2) that produces clean surfaces for sensitization (as verified by AFM) resulting in near unity yields for electron transfer from the molecular excited dyes into the conduction band. In recent experiments with ruthenium complexes at TiO(2) and with carboxylated cyanine dyes, we demonstrate the promise of this simple model for understanding dye-sensitized solar cells. In each of these systems, we can observe and analyze the complex photochemistry in a quantitative manner. Molecules of the well-known N3 ruthenium complex attach to four different crystallographic faces of anatase and rutile TiO(2) at different rates and to a different extent. With carboxylated cyanine dye sensitizers on these surfaces, molecular aggregation on the surface is a function of molecular structure and crystallographic face. In contrast with the N3 sensitizer these organic dyes undergo a photoinduced dimerization and desorption reaction when hydroquinone regenerators are present. With both classes of sensitizers, we demonstrate a new photochronocoulometric technique that quantifies the amount of attached dye on the electrode surface. We have completed initial experiments examining quantum dot sensitization of TiO(2) crystals, which could eventually lead to sensitizers with higher stability and absorption coefficients. Although these single crystal electrode models show promise for providing insights and predictive value in understanding the sensitization process, more sophisticated models will be needed to fully understand the charge transfer from the localized electronic states of the sensitizer to the extended states of the semiconductor.

Recent advances have been made in thin-film solar cells using CdTe and CuIn(1-x)Ga(x)Se(2) (CIGS) nanoparticles, which have achieved impressive efficiencies. Despite these efficiencies, CdTe and CIGS are not amenable to large-scale production because of the cost and scarcity of Te, In, and Ga. Cu(2)ZnSnS(4) (CZTS), however, is an emerging solar cell material that contains only earth-abundant elements and has a near-optimal direct band gap of 1.45-1.65 eV and a large absorption coefficient. Here we report the direct synthesis of CZTS nanocrystals using the hot-injection method. In-depth characterization indicated that pure stoichiometric CZTS nanocrystals with an average particle size of 12.8 +/- 1.8 nm were formed. Optical measurements showed a band gap of 1.5 eV, which is optimal for a single-junction solar device.

The cost effective generation of hydrogen with sunlight via water photoelectrolysis is the critical breakthrough needed to transition the world to a renewable energy based hydrogen economy. A semiconductor based photoelectrolysis system may have cost advantages over using either a photovoltaic cell coupled to an electrolyzer or solar thermochemical cycles for water splitting. Unfortunately there is no known semiconducting material or combination of materials with the electronic properties and stability needed to efficiently photoelectrolyze water. Semiconducting oxides can have the required stability but present theoretical methods are insufficient to a priori identify materials with the required properties. Most likely, the discovered material will be a complex oxide containing many elements whereby each contributes to the required material properties such as light absorption across the solar spectrum, stability and electrocatalytic activity. The large number of possible multicomponent metal oxides, even if only ternary or quaternary materials are considered, points to the use of high-throughput combinatorial methods to discover and optimize candidate materials. In this critical review, we will cover some techniques for the combinatorial production and screening of metal oxides for their ability to efficiently split water with sunlight (88 references).

A photon-initiated desorption of a dicarboxylated thiacarbocyanine dye from a dye-sensitized semiconducting oxide crystal has been observed when hydroquinone is used as a regenerator. No desorption was found under the same conditions when KI was used as the regenerator. Intermittent illumination experiments suggest that the oxidation products of the hydroquinone regenerator compete for dye adsorption sites. By comparing the photocurrent decay at both the dye monomer sensitization maximum and the dimer sensitization maximum, a rearrangement of monomer into dimer was observed. A kinetic model for the photocurrent decay as a function of desorption time was derived, and the desorption rate constants were obtained by fitting the experimental data to the model.