Search

Purpose: To assess and compare the clinical outcomes of three different types of all-ceramic posterior monolithic tooth-supported crowns. Materials and Methods: A total of 71 patients received 90 all-ceramic crowns randomized to be either high-translucency zirconia (ZC), high-translucency zirconia with a partial buccal veneer (ZC-V), or lithium disilicate glass-ceramic (LDS). All treatments were performed by four general dentists who were blinded to the material used. Baseline and subsequent annual evaluations were based on modified California Dental Association (CDA) criteria. A questionnaire was used to include patient-reported outcomes and to compare them to the crown quality rating performed by dentists. Results: A total of 66 patients with 84 crowns were examined after 3 years. The survival rate was 98.8%. No crowns fractured during the observation period. One ZC-V crown failed due to loss of retention, and three complications were noted: loss of retention occurred in one ZC crown, and two ZC crowns needed to be endodontically treated. There was no significant difference between the different crowns regarding marginal integrity, surface, or anatomical form. Both patients and examining dentists rated the crowns favorably regarding esthetics, patients more than dentists. Conclusions: All crown types used show excellent and promising clinical outcomes from a short-term perspective. Patients and dentists rate the restorations favorably concerning esthetics and function. [ABSTRACT FROM AUTHOR]

Purpose: To determine the biologic and biomechanical effects of two implant drilling protocols on the cortical bone around implants subjected to immediate loading. Materials and Methods: A total of 48 implants were inserted into the mandibles of six sheep following one of two drilling protocols: undersized preparation (US; n = 24) and nonundersized preparation (NUS; n = 24). Immediately after implant insertion, an abutment was placed on each implant and 36 implants were subjected to 10 sessions of dynamic vertical loads (1,500 cycles, 1 Hz) of 25 N or 50 N. Insertion torque value (ITV) was recorded at implant installation. Resonance frequency analysis (RFA) was measured at implant insertion and at each loading session. Fluorochrome was administered at day 17, and the animals were euthanized after 5 weeks. The removal torque values (RTVs) were measured, and samples underwent histomorphometric, μCT (microcomputed tomography), and fluorescence image acquisition analyses. The bone volume density (BV/TV), bone-to-implant contact (BIC), bone area fraction occupancy (BAFO), and fluorochrome stained bone surface (MS) were calculated. A linear mixed model analysis was performed, and Pearson paired correlation was calculated. Results: Five implants from the NUS group failed, with a mean ITV of 8.8 Ncm and an RFA value of 57. The mean ITVs for US group and NUS group were 80.5 (± 14) Ncm and 45.9 (± 25) Ncm, respectively (P < .001). No differences were noted in the RFA values from the time of implant insertion until the end of the study. No differences in RTV, BV/TV, BAFO, or MS were observed between the groups. Intense new bone formation took place in the NUS group implants that were subjected to load. Conclusions: Undersized preparation of cortical bone ensured a greater BIC compared to a nonundersized preparation. Moreover, this study demonstrated that immediate loading did not interfere with the osseointegration process, but loading induced intense new bone formation in the NUS group. It is not recommended to immediately load the implants when the clinically perceived primary stability is lower than an ITV of 10 Ncm and an RFA value of 60. [ABSTRACT FROM AUTHOR]

Introduction: Different materials and restorative concepts have been proposed over the years to restore endodontically treated teeth (ETT). Monolithic ceramic and composite restoration can be lute to the tooh, without the use of a post. However, little is known how the material stiffness and presence of a composite core will affect the survival and failure mode. The objective of this in‐vitro study was to evaluate the fracture strength and failure mode of endodontically treated molars, restored with ceramic or hybrid composite monolithic restoration, in the presence of absence of a composite core. Materials and Methods: Sixty depulped molars were restored with a lithium‐disilicate (e.max CAD) or hybrid composite (Cerasmart) restoration. Both materials were used in a monolithic approach, but with 3 different designs: (a) monolithic endocrown, (b) crown with a separate composite core, and (c) overlay without core buildup or pulpal extension. Ten sound teeth were used as control group. All groups were thermocycled (10,000 cycles), subsequently loaded in a chewing simulator (100,000 cycles) and finally loaded until fracture. Results: Peak fracture loads and failure modes were registered. No significant differences were seen between the groups in terms of fracture load. Failure modes were statistically significantly different among groups with significant correlation between restoration type and material. (p < 0.001 and p = 0.033, respectively). No group presented significantly higher fracture resistance. Although ceramic crowns and overlays presented the highest repairability, all restored ETT were within the range of the intact tooth' fracture strength. Conclusion: No restoration presented significant different fracture loads. However, the type of restoration and material choice were correlated to the fracture mode. [ABSTRACT FROM AUTHOR]

Aim: A large variety of dental materials are available for the production of implant-supported fixed restorations. Materials with different properties are likely to behave differently during clinical function, which may result in different prevalence and types of complications. The aim of the present review was to summarise, analyse and discuss the prevalence and types of complications or failures related to dental materials in implant-supported restorations. Materials and methods: A strategy was set up using the PICO format and the search was performed using the PubMed database, including a hand search of reference lists. Two independent reviewers selected papers based on a set of criteria. The number of events of complications was summarised. Results: The initial search produced 2764 titles. After application of criteria, 47 publications were selected for analysis. Seventeen studies reported on 1447 single crowns and 30 studies reported on 2190 fixed dental prostheses. The most common complications were fracture or chipping of the veneer material, loss of retention and lost access hole fillings. Due to the heterogeneity of studies, and large variation in number of restorations per material group, no conclusive correlation between type of material and type of technical complication and/or failure could be established. Conclusions: The review did not succeed in providing convincing evidence to answer the question concerning a possible relationship between restoration materials and prevalence of technical complications in implant-supported restorations. [ABSTRACT FROM AUTHOR]

Objectives: This randomised controlled trial compares the 3‐year outcomes, that is, marginal bone‐level (MBL) changes and clinical parameters, between an abutment‐level (AL) and implant‐level (IL) connection for implants with an internal conical connection (ICC) supporting a screw‐retained fixed partial denture. Material and methods: Fifty patients with 119 implants were randomly allocated to either the AL or IL group. Radiographic and clinical examinations were performed after one, two, and 3 years. A linear mixed model was used to evaluate the differences between groups. Results: The MBL change was not significantly different between the groups at any point. The MBL was 0.12 ± 0.31 mm (AL) and 0.23 ± 0.26 mm (IL) after 1 year; 0.15 ± 0.34 mm (AL) and 0.17 ± 0.22 mm (IL) after 2 years; 0.18 ± 0.39 mm (AL) and 0.15 ± 0.21 mm (IL) after 3 years. The bleeding on probing was 43.44 ± 39.24% (AL) and 58.19 ± 41.20% (IL) after 1 year; 35.78 ± 39.22% (AL) and 50.43 ± 41.49% (IL) after 2 years; 51.27 ± 44.63% (AL) and 49.57 ± 37.31% (IL) after 3 years and was significantly different (p =.025) between 1 and 2 years. The probing depth showed a significant difference at each time point while the plaque was not significant between the groups. The overall technical, biological and prosthetic complication rates were 5.04%, 3.36%, and 16.00%, respectively. Conclusions: The MBL change was similar in the groups. The slight differences in the soft tissue complications between the groups are likely not of clinical relevance. An IL connection is considered to be a valid alternative to an AL set‐up in ICC implants. [ABSTRACT FROM AUTHOR]

The purpose was to evaluate the bond strength between adhesive cement and translucent zirconia in comparison to conventional zirconia. Four brands of translucent zirconia (BruxZir® HT, Lava™ Plus, Prettau® Anterior, and Prettau® Zirconia) and one conventional zirconia (Kavo Everest® ZS) were evaluated. Specimens were divided into groups depending on the pretreatment of the cementation surface of the zirconia: as-produced, hydrofluoric acid treatment, or sandblasted. The groups underwent three different procedures of artificial aging: water storage (24 h), 5,000 thermocycles, or long-term aging, (water storage 150 days including 37,500 thermocycles) before shear bond strength testing. Sandblasting treatment increased the bond strength significantly for all the brands of zirconia, irrespective of artificial aging procedures, in comparison to the control group. Bond strength between adhesive cement to translucent zirconia is equivalent to conventional zirconia. Sandblasting creates a cementation surface that is more durable than as-produced or hydrofluoric-acid-treated, irrespective of type of zirconia. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the load‐bearing capacity and failure mode of monolithic zirconia fixed dental prostheses (FDPs) fabricated with different connector designs and embrasure shaping methods. Materials and Methods: Seventy four‐unit zirconia FDPs (with two premolar pontics) were fabricated and divided into seven groups (n = 10) according to the different connector designs gained by using different embrasure shaping methods. The groups were as follows: monolithic FDPs fabricated with sharp embrasures, monolithic FDPs fabricated with blunt embrasures, monolithic FDPs fabricated with blunt embrasures and no occlusal embrasures, two groups of monolithic FDPs fabricated with blunt embrasures and interproximal separations made with diamond discs at the soft stage and at the fully sintered stage, and monolithic FDPs fabricated with blunt embrasures and interproximal separation accentuated by localized porcelain build‐up. A final group was used as a control group, where fully veneered traditional zirconia FDPs were fabricated with default milling settings. The FDPs were artificially aged and loaded to fracture. Load to fracture and failure modes were analyzed by one‐way ANOVA, Tukey's post hoc test, and Fisher exact test (α = 0.05). Results: The FDPs fabricated with interproximal porcelain separation showed significantly the highest load to fracture (1038 N ± 82) of all groups (p < 0.001), with no significant difference compared to the FDPs with no occlusal embrasures (934 N ± 175; p ˃ 0.29). The FDPs fabricated with blunt embrasures showed significantly higher load to fracture (873 N ± 115) compared to the FDPs in the control group (689 N ± 75) and the FDPs with sharp embrasures (417 N ± 87; p < 0.001). There were no significant differences between the FDPs with sharp embrasures (417 N ± 87) and the FDPs with interproximal disc separations (467 N ± 94; p ˃ 0.23). Failure mode of the FDPs fabricated with sharp embrasures and interproximal disc separations differed significantly compared to the FDPs in the other groups (p < 0.001). Conclusions: Sharp embrasures and interproximal separations made with diamond discs significantly decrease the load‐bearing capacity of monolithic zirconia FDPs compared to FDPs made with blunt embrasures. Blunt embrasures in combination with localized porcelain build‐up produce FDPs with high load‐bearing capacity in relation to loads that might be expected under clinical use. [ABSTRACT FROM AUTHOR]

The following aims were set for this systematic literature review: ( a) to make an inventory of existing methods to achieve bondable surfaces on oxide ceramics and ( b) to evaluate which methods might provide sufficient bond strength. Current literature of in vitro studies regarding bond strength achieved using different surface treatments on oxide ceramics in combination with adhesive cement systems was selected from PubMed and systematically analyzed and completed with reference tracking. The total number of publications included for aim a was 127 studies, 23 of which were used for aim b. The surface treatments are divided into seven main groups: as-produced, grinding/polishing, airborne particle abrasion, surface coating, laser treatment, acid treatment, and primer treatment. There are large variations, making comparison of the studies difficult. An as-produced surface of oxide ceramic needs to be surface treated to achieve durable bond strength. Abrasive surface treatment and/or silica-coating treatment with the use of primer treatment can provide sufficient bond strength for bonding oxide ceramics. This conclusion, however, needs to be confirmed by clinical studies. There is no universal surface treatment. Consideration should be given to the specific materials to be cemented and to the adhesive cement system to be used. © 2013 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 102B: 395-413, 2014. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the load-bearing capacity and failure mode of monolithic zirconia fixed dental prostheses (FDPs) fabricated with different connector designs and embrasure shaping methods., Materials and Methods: Seventy four-unit zirconia FDPs (with two premolar pontics) were fabricated and divided into seven groups (n = 10) according to the different connector designs gained by using different embrasure shaping methods. The groups were as follows: monolithic FDPs fabricated with sharp embrasures, monolithic FDPs fabricated with blunt embrasures, monolithic FDPs fabricated with blunt embrasures and no occlusal embrasures, two groups of monolithic FDPs fabricated with blunt embrasures and interproximal separations made with diamond discs at the soft stage and at the fully sintered stage, and monolithic FDPs fabricated with blunt embrasures and interproximal separation accentuated by localized porcelain build-up. A final group was used as a control group, where fully veneered traditional zirconia FDPs were fabricated with default milling settings. The FDPs were artificially aged and loaded to fracture. Load to fracture and failure modes were analyzed by one-way ANOVA, Tukey's post hoc test, and Fisher exact test (α = 0.05)., Results: The FDPs fabricated with interproximal porcelain separation showed significantly the highest load to fracture (1038 N ± 82) of all groups (p < 0.001), with no significant difference compared to the FDPs with no occlusal embrasures (934 N ± 175; p ˃ 0.29). The FDPs fabricated with blunt embrasures showed significantly higher load to fracture (873 N ± 115) compared to the FDPs in the control group (689 N ± 75) and the FDPs with sharp embrasures (417 N ± 87; p < 0.001). There were no significant differences between the FDPs with sharp embrasures (417 N ± 87) and the FDPs with interproximal disc separations (467 N ± 94; p ˃ 0.23). Failure mode of the FDPs fabricated with sharp embrasures and interproximal disc separations differed significantly compared to the FDPs in the other groups (p < 0.001)., Conclusions: Sharp embrasures and interproximal separations made with diamond discs significantly decrease the load-bearing capacity of monolithic zirconia FDPs compared to FDPs made with blunt embrasures. Blunt embrasures in combination with localized porcelain build-up produce FDPs with high load-bearing capacity in relation to loads that might be expected under clinical use., (© 2018 by the American College of Prosthodontists.)

The traditional zinc phosphate cementation technique for crowns and fixed partial dentures (FPDs) is based on mechanical retention where the geometry of the prepared tooth provides retention for the restoration. In clinical situations where mechanical retention is compromised or regarded insufficient, a bonding system can be used to provide retention. This study investigates whether bond strengths of different bonding systems to densely sintered high-strength alumina ceramics are sufficient. One hundred twenty pairs of industrially manufactured specimens--one block and one cylinder-shaped disc of densely sintered alumina--were used. The cementation surfaces of the blocks were sandblasted with 110-microm aluminium oxide while the cementation surfaces of the discs were left untreated, as produced. The pairs were then bonded with one of six different bonding systems. Each bonding group of 20 samples was randomly divided into thermocycled and non-thermocycled subgroups (n=10). Both subgroups were stored 1 week in distilled water (37 degrees C). During this week, the thermocycled subgroup underwent 5000 thermocycles (5 degrees C-55 degrees C). Following pre-treatment, the specimens were loaded until fracture in a universal testing machine to determine shear bond strength. Data were analysed using student's t-test and a one-way ANOVA. Fractured interfaces were examined under a light microscope to classify the failure mode of the debonded area as adhesive, cohesive, or a combination of the two. The highest bond strengths, achieved with two of the bonding systems, were significantly higher than the remaining bonding systems, irrespective of pretreatment--(p>0.001). The predominant failure mode for both treated and untreated surfaces was adhesive. Two of the six tested bonding systems achieved sufficient shear bond strength to densely sintered alumina. Furthermore, recommendations on whether to use surface-treated or as produced densely sintered alumina must be based on which bonding system is being used.