Search

ABSTRACT Objective The clivus is trapezoidal in shape with uneven bone structure, the optimal number and position of screws for clival fixation are not clear. Therefore, this study aims to explore the optimization clival screw fixation method for occipitocervical instability using finite element analysis. Methods Seven finite element models were developed to evaluate biomechanical properties of clival screw fixation for treating occipitocervical stability, including (i) one clival screw fixation A1 and A2 models; (ii) two clival screws fixation B1 and B2 models; (iii) three clival screws fixation C1 and C2 models; (iv) four clival screws fixation D1 model. Loads of 1.5 Nm were applied to the model fRoM different directions to induce flexion, extension, lateral bending, and axial rotation movements. Results The regular triangle C1 type three clival screws fixation exhibited great stability, with RoM of 4.20° in flexion, 5.80° in extension, 0.85° in lateral bending, and 1.60° in axial rotation. The peak stress on the internal fixation devices were relatively low, with maximum screw stress of 194 MPa in flexion, 276 MPa in extension, 180 MPa in lateral bending, and 213 MPa in axial rotation; the maximum plate stress were 126, 554, 426, and 378 MPa, respectively. The areas with higher stress were mainly concentrated at the robust neck section of the plate. Conclusion The triangular configuration of three clival screws fixation represented the optimized anterior occipitocervical fixation method through the clivus, offering superior biomechanical stability, lower stress on the devices and dispersed stress distribution in the occipitocervical region.

Objective To evaluate the biomechanical stability of anterior transarticular crossing screw (ATCS) and compare it with anterior transarticular screw (ATS) which may provide basic evidence for clinical application. Methods Eight human fresh cadaveric specimens (occiput-C4) were tested with 5 conditions including the intact status, the injury status (type II odontoid fracture), the injury+ATS fixation status (traditional bilateral ATS fixation); the injury+unilateral ATCS fixation status; and the injury+bilateral ATCS fixation status. Specimens were applied to a pure moment of 1.5 Nm in flexion-extension, lateral bending, and axial rotation, respectively. The range of motions (ROMs) and the neutral zones (NZs) of C1 to C2 segment were calculated and compared between 5 status. Results ATS and ATCS fixations significantly reduced the motions in all directions when compared with the intact and injury statues (p < 0.05). In flexion-extension, the ROMs of ATS, unilateral ATCS, and bilateral ATCS were 4.7° ±2.5°, 4.1° ±1.9°, and 3.2° ±1.2°, respectively. Bilateral ATCS resulted in a significant decrease in ROM in flexion-extension when compared with ATS and unilateral ATCS (p = 0.035 and p = 0.023). In lateral bending and axial rotation, there was no significant difference in ROM between the 3 fixations (p > 0.05). Three fixations resulted in similar NZs in all directions (p > 0.05). Conclusion ATCS is a biomechanically effective alternative or supplemental method for atlantoaxial instability.

Objective To investigate the characteristics of functional muscle and muscle size in patients with basilar invagination (BI) and explore the effects of atlantoaxial dislocation. Methods Eighty BI patients (BI group) and 80 age- and sex-matched asymptomatic people (control group) were included. Axial T2 magnetic resonance imaging image was used to measure the cross-sectional area (CSA) and functional CSA (FCSA). The sternocleidomastoid (SCM), longus capitis and longus colli (LCap & LC), trapezius (Trap), splenius capitis (SpCap), splenius cervicis (SpC), semispinalis capitis (SSCap), semispinalis cervicis (SSC), multifidus (MS), levator scapulae (LS) and posterior deep layer muscles (PDLM) were evaluated. Correlations between age, atlantodental interval (ADI), Chamberlain distance and muscles were observed. Results BI group (39.4 ± 18.4 years; 33 males/47 females) exhibited significantly lower FCSA/CSA ratios than the control group in all extensor and flexor muscles, and presented smaller CSAs on the right and left Trap, SSC, LS, SCM, and left LCap & LC. FCSA/CSA ratios were significantly lower in BI patients with dislocation on the right Trap, SpCap, SpC, SSCap, MS, LS, LCap & LC, and PDLM, and the left SSCap, MS, and LCap & LC than in patients without deformity. Additionally, functional muscles of all parameters decreased with age in BI patients. Excluding children, the Trap, SpC, MS, and LS muscle sizes of BI patients tended to increase with age. ADI and Chamberlain distance tended to correlate negatively with FCSA/CSA ratio. Conclusion The BI patients, especially those with atlantoaxial dislocation, had less functional muscles compared with the control group. Moreover, their functional muscles decreased with age more obviously.

Study Design. Retrospective study. Objective. To evaluate the feasibility of C2 pedicle screw fixation with the "in-out-in" technique in patients with basilar invagination (BI). Summary of Background Data. The "in-out-in" technique is a fixation technique in which the screw enters the vertebrae through the parapedicle. The technique has been used in upper cervical spine fixation. However, anatomic parameters associated with the application of this technique in patients with BI are unclear. Materials and Methods. We measured the C2 pedicle width (PW), the distance between the vertebral artery (VA) and the transverse foramen (VATF), the safe zone, and the limit zone. The lateral safe zone is the distance from the medial/lateral cortex of the C2 pedicle to the VA (LPVA/MPVA), and the medial safe zone is the distance from the medial/lateral cortex of the C2 pedicle to the dura (MPD/LPD). The lateral limit zone is the sum of LPVA/MPVA and VATF (LPTF/MPTF), and the medial limit zone is the distance from the medial/lateral cortex of the C2 pedicle to the spinal cord (MPSC/LPSC). PW, LPVA, MPVA, and VATF were measured on the reconstructed CT angiography. PW, MPD, LPD, MPSC, and LPSC weremeasured onMRI.We define a width greater than 4mmas safe for screw. The t-test was used to compare the parameters between male and female, left and right sides in all patients, and PW in CTA and MRI data in the same patient. For intrarater reliabilities, interclass correlation coefficients were calculated. Results. A total of 154 patients (49 CTA, 143 MRI) were included. The average PW, LPVA, MPVA, LPTF, MPTF, MPD, LPD, MPSC, and LPSC were 5.30 mm, 1.28 mm, 6.60 mm, 2.45 mm, 8.94 mm, 2.09 mm, 7.07 mm, 5.51 mm, and 10.48 mm, respectively. Furthermore, in patients with PW < 4 mm, 53.6% of MPVA, 86.2% of LPTF, and all limit zones were larger than 4 mm. Conclusions. In patients with BI, there is sufficient space medially and laterally to the C2 pedicle for partial screw encroachment to achieve "in-out-in" fixation, even if the pedicle is small. [ABSTRACT FROM AUTHOR]