Search

Direct steam generation (DSG) concentrating solar power (CSP) plants uses water as heat transfer fluid, and it is a technology available today. It has many advantages, but its deployment is limited due to the lack of an adequate long-term thermal energy storage (TES) system. This paper presents a new TES concept for DSG CSP plants. This system is based on three blocks, a saturated block based on phase change materials, an overheating block that elevates the vapor temperature of a heat transfer fluid to the desired values, and a preheating block that increases the temperature difference between a cold tank and a hot tank of a non-phase change thermal storage material. After a deep selection and characterization process, the material to be used is LiOH/KOH, since although it has the disadvantage of high corrosion, the identified advantages overcome it as an ideal PCM for this process.

Thermal management protects against external agents and increases the lifetime and performance of the devices in which it is implemented. Because of their ability to store and release a high amount of energy at a nearly constant temperature, phase change materials (PCMs) are promising thermoregulatory materials. Thus, the manufacture of PVDF fibers containing PCMs has advantages since PVDF is already used in elements that are susceptible to thermal management as a binder in batteries or as a base material for fabrics. This work presents a simple, versatile, in situ, cost-effective, and easy-to-scale-up method to produce PVDF-based fibers containing paraffin RT-28HC for thermal management. To achieve that goal, the microfluidic approach of coaxial flows was simplified to gravity-aided laminar jet injection into a bulk fluid, where fibers were produced by the solvent extraction mechanism. With this methodology, hollow PVDF fibers and core-shell PVDF fibers containing paraffin RT-28HC have been produced. The proposed approach resulted in fibers with up to 98 J/g of latent heat, with a hierarchical porous structure. SEM study of the fiber morphology has shown that PCM is in the form of slugs along the fibers. Such PCM distribution is maintained until the first melting cycle, when molten PCM spreads within the fiber under capillary forces, which was observed by an infrared camera. Manufactured composite fibers have shown low thermal conductivity and high elasticity, which suggest their potential application as a thermal insulation material with thermal buffer properties. Leakage tests revealed outstanding retention capacity with only 3.5% mass loss after 1000 melting/crystallization cycles. Finally, tensile tests were carried out to evaluate the mechanical properties of the fibers before and after thermal cycling.

This work presents the effect of atomic substitution on the MnFe2O4-Na2CO3 thermochemical cycle for H-2 production. The non-oxidative decarbonation/carbonation reaction of the MnFe2O4-Na2CO3 mixture is investigated as the starting reference. Repeated cycling results in a 30% loss of reversibility due to an overall reduction of the reactive interfaces. The substitution of Na2CO3 for Li2CO3 decreases the decarbonation onset temperature by about 100 degrees C, but almost no reversibility is observed during the cycles due to the irreversible Li+ intercalation. The effect of partial Mn substitution for Ca, Ni, and Zn is presented. The 5% Zn mixture shows the best decarbonation/carbonation reversibility and is tested for H-2 production together with MnFe2O4-Na2CO3. The reference mixture produces more H-2 during the first cycle (asymptotic to 1.1 vs. 0.7 mmol/g), but its production drastically drops by two orders of magnitude upon cycling and becomes negligible after 5 cycles. By contrast, the Zn-doped mixture exhibits a stable H-2 production of 0.22 mmol/g with no decreasing trend observed from cycle 2 to cycle 5. As result, in the fifth cycle, the Zn-doped mixture produces 23 times more H-2 than MnFe2O4-Na2CO3. Thermogravimetry and X-ray diffraction confirm that doping with Zn significantly improves the regeneration of the reactants.

The NPG–TRIS binary system (NPG = (CH3)2C(CH2OH)2 = 2,2-dimetyl-1,3-propanodiol; TRIS = NH2C(CH2OH)3 = 2-Amino-2-(hydroxymethyl)-1,3-propanediol) was intensively investigated as a thermal energy storage system, due to the reversibility of its phase transitions and their associated energy. An adapted methodology was applied to precisely quantify its sublimation tendency. Relevant thermochemical data were revisited and evaluated using some specific experimental procedures. We also determined that the widely accepted requirement of working in an inert atmosphere to avoid deviations due to hygroscopicity is not necessary. Nevertheless, to take advantage of the energetic properties of the NPG–TRIS system, closed containers will be required to avoid NPG losses, due to its quantitatively determined high sublimation tendency.

Peritectic compound Li4(OH)3Br has been recently proposed as phase change material (PCM) for thermal energy storage (TES) applications at approx. 300 °C Compared to competitor PCM materials (e.g., sodium nitrate), the main assets of this compound are high volumetric latent heat storage capacity (>140 kWh/m3) and very low volume changes (<3%) during peritectic reaction and melting. The objective of the present work was to find proper supporting materials able to shape stabilize Li4(OH)3Br during the formation of the melt and after its complete melting, avoiding any leakage and thus obtaining a composite apparently always in the solid state during the charge and discharge of the TES material. Micro-nanoparticles of MgO, Fe2O3, CuO, SiO2 and Al2O3 have been considered as candidate supporting materials combined with the cold-compression route for shape-stabilized composites preparation. The work carried out allowed for the identification of the most promising composite based on MgO nanoparticles through a deep experimental analysis and characterization, including chemical compatibility tests, anti-leakage performance evaluation, structural and thermodynamic properties analysis and preliminary cycling stability study.