Search

Design an extended osteotomy guide (EOG) for Le Fort I osteotomy to improve the safety of surgery.The digital Le Fort I osteotomy guide was designed in MIMICS 23.0. Twenty-eight patients were randomized into 2 groups. Patients in the experimental group used EOG, and patients in the control group used a traditional osteotomy guide (TOG). Virtual designs and actual postoperative outcomes were compared by cone-beam computed tomography. The safety of the operation was confirmed by the accuracy of the osteotomy direction and depth on the inner and posterior walls of the maxilla.All positioning deviations of both osteotomy guides were0.3 mm (P0.05). The osteotomy depths on the inner and posterior walls with the EOG and TOG deviated by 0.789±1.179 and 1.811±1.345 mm (P=0.004) and 0.648±0.999 and 1.262±0.942 mm (P=0.030), respectively. The angles of deviation of the osteotomy direction on the inner and posterior walls by the EOG and TOG were 2.025±2.434 and 5.069±2.391 degrees (P0.001) and 2.772±2.979 and 8.653±4.690 degrees (P0.001), respectively.The EOG was more accurate than TOG for manipulating osteotomy direction and depth on the inner and posterior maxillary walls. Thus, EOG could ensure higher surgical safety than TOG.

Low physical activity (PA) and high sedentary behavior (SB) place residents in assisted living at risk for physical decline, but little is known about factors that influence PA/SB in this setting. In the current cross-sectional study, we described objectively measured PA/SB (activPAL™) and examined the relationships between PA/SB and use of an assistive walking device, depression, sleep disturbance, pain, fatigue, social isolation, and the tendency to make social comparisons. Fifty-four residents from eight assisted living facilities participated. Mean time spent in PA was 252.9 ( SD = 134.3) minutes/day. Mean time spent in SB was 660.8 ( SD = 181.4) minutes/day. Depression predicted PA (R2 = 0.16). Residents using an assistive device spent significantly more time in SB ( p = 0.02). Fatigue correlated with time in longer bouts of SB ( r = 0.19, p = 0.04). The tendency to make social comparisons correlated with SB ( r = 0.22, p = 0.04). Findings show residents in assisted living are inactive and further research is needed to fully understand factors that influence PA/SB. [ Research in Gerontological Nursing, 15 (3), 117–123.]

The Reamer-Irrigator-Aspirator (RIA-2) system has been established as a safe and reliable device to harvest large amounts of autograft. Nevertheless, hardware complications may occur. Breakage of the reamer head from the drive shaft with intramedullary retention of small metal debris has never been dealt with. The authors provide a technical trick as a bailout in this difficult situation.

While performing musculoskeletal long bone fracture reduction surgery, assistant surgeons can often suffer from physical fatigue as they provide resistance against the tension from surrounding muscles pulling on the patient’s broken bones. These days, robotic systems are being actively developed to mitigate this physical workload by realigning and holding these fractured bones for surgeons. This has led to one consortium proposing the development of a robot-assisted fracture reduction system consisting of a 6-DOF positioning robot along with a 1-DOF traction device. With the introduction of the 1-DOF traction device, the positioning robot does not have to fight these contraction forces so can be compact improving its maneuverability and overall convenience; however, considering surgeon-robot interactions, this approach adds the requirement of controlling two different types of robots simultaneously. As such, an advanced cooperative control methodology is required to control the proposed bone fracture reduction robot system. In this paper, a human-robot-robot cooperative control (HRRCC) scheme is proposed for collaboration between the surgeon, the positioning robot, and the traction device. First, the mathematical background of this HRRCC scheme is provided. Next, we describe a series of experiments that show how the proposed scheme facilitates a reduction in the load placed on the positioning robot from strong muscular contraction forces making it possible to conduct fracture reduction procedures more safely despite the muscular forces.

The global orthopedic devices market is expected to reach nearly $72 billion by 2026, representing 12% of the projected global medical devices market. The vantage point of surgeons conveniently places them at the crossroads of surgery, therapy, and inpatient and outpatient dynamics, providing fertile ground for the invention of medical devices. This review article aims to provide an overview for how surgeons should take on launching a product in the medical device industry. In Part 1, we cover idea development, industry partnerships, and commercialization. Part 2 will cover the patent and United States Food and Drug Administration submission processes.

Study design Prospective cohort study with two times of measurement. Objective To assess the relationship between use of assistive devices for walking (at baseline) and the number of annual fall-related injuries (at follow-up) among a cohort of ambulatory adults with spinal cord injury (SCI). Setting Medical University in the Southeastern United States. Methods There were 622 ambulatory adults who met the eligibility criteria, 317 of whom completed both baseline and follow-up assessments. The participants completed a mailed self-report assessment (SRA) that measured self-reported number of fall-related injuries in the previous year, and the use of orthopedic equipment (assistive devices) for walking, including cane(s), crutches, walker, and braces, was assessed at both baseline and follow-up. Results The percentage of at least one self-reported fall-related injury decreased from 22% at baseline to 13% at the follow-up. Walker and cane use at baseline was significantly associated with fall-related injuries at follow-up. Participants using one walking device related to 194% greater number of fall injures, and using multiple device related to 730% greater number of fall injures than those who used no devices. We also found walker users were associated with 214% greater number of fall injures, while cane users were associated with 160% greater number of fall injures. Conclusions The probability of fall-related injury remained high among persons who are ambulatory after SCI. Health care professionals should be aware of the balance between the goal of ambulation and the potential increased risk of fall-related injuries associated with assistive device use.

As drilling generates substantial bone thermomechanical damage due to inappropriate cutting tool selection, researchers have proposed various approaches to mitigate this problem. Among these, improving the drill bit design is one of the most feasible and economical solutions. The theory and applications in drill design have been progressing, and research has been published in various fields. However, pieces of information on drill design are dispersed, and no comprehensive review paper focusing on this topic. Systemizing this information is crucial and, therefore, the impetus of this review. Here, we review not only the state-of-the-art in drill bit designs-advances in surgical drill bit design-but also the influences of each drill bit geometries on bone damage. Also, this work provides future directions for this topic and guidelines for designing an improved surgical drill bit. The information in this paper would be useful as a one-stop document for clinicians, engineers, and researchers who require information related to the tool design in bone drilling surgery.

One of the major problems with walking encountered by patients with spastic hemiplegia is diminished toe clearance due to spasticity of their leg muscles. To improve their walking, a specialized robot assist for ankle movements (RE-Gait) has been utilized. The present study examined the neurophysiological effects whether spinal cord reciprocal Ia inhibition (RI) in the leg was altered by using RE-Gait. Sixteen patients with a clinical diagnosis of stroke were divided into the two groups, RE-Gait walking group (Group R) and normal (controlled) walking group (Group C). In each group, they walked on a flat floor for 15 min with or without RE-Gait. The depression of soleus (Sol) H-reflexes conditioned by common peroneal nerve stimuli with the conditioning-test (C-T) intervals of 1, 2, 3, and 4 ms were assessed before and immediately after each walking session. After the intervention, the LSM (SE) of Sol H-reflex amplitude with 1, 2 and 3 ms C-T interval conditions were significantly decreased in group R (1 ms: 88.15 (4.60), 2 ms: 86.37 (4.60), 3 ms: 89.68 (4.62)) compared to group C (1 ms: 105.57 (4.56), 2 ms: 100.89 (4.58), 3 ms: 107.72 (4.58)) [1 ms: p = 0.012, 2 ms: p = 0.035, 3 ms: p = 0.011]. Walking assistive robot that targets ankle movements might be a new rehabilitation tool for regulating spinal cord excitability.

The reliability of knee extensor and flexor strength measurements was assessed in 20 women (aged 68-88 years) who had experienced a hip fracture two to four weeks before but who were otherwise healthy. Using the Cybex 6000 isokinetic dynamometer, isokinetic knee extensor and flexor strength (peak torque, total work and power) at 30 and 120 degree/second and isometric knee extensor and flexor strength (peak torque) were measured by the same examiner in both legs, successively, on four separate days within one week. Compared with the non-involved leg, the median reduction in peak extensor and flexor torque of the involved leg was 50% (p0.001). With the protocol used, no significant change in muscle strength occurred during the test period Individual coefficients of variation (CVs) were calculated for each muscle strength variable. Depending on whether torque, work or power were measured, the median CVs of extensor and flexor strength measurements of the non-involved leg ranged from 5.6-14.6% and 10.8-28.6%, respectively. The corresponding CVs for the involved leg were 10.9-22.1% and 13.0-35.2%. Substantial variability between individual CVs were found for all strength variables. In conclusion, although muscle strength measurements may be applicable when comparing larger groups of hip fracture patients, the large CVs may be a limitation in monitoring individual patients. This finding should be taken into consideration when planning individual training programmes.

Antibiotic resistance represents a key challenge of the 21st century. Since the pipeline of new antibiotics in development is limited, the introduction of alternative antimicrobial strategies is urgently required. Bacteriophage therapy, the use of bacterial viruses to selectively kill bacterial pathogens, is re-emerging as a potential strategy to tackle difficult-to-treat and multidrug-resistant pathogens. The last decade has seen a surge in scientific investigation into bacteriophage therapy, including targeting orthopaedic-device-related infections (ODRIs) in several successful case studies. However, pharmacological data, knowledge on the interplay with the immune system and, especially in ODRIs, the optimal local application strategy and treatment outcomes remain scarce. The present review reports the state-of-the-art in bacteriophage therapy in ODRIs and addresses the hurdles in establishing bacteriophage therapy under good clinical practice guidelines. These hurdles include a lack of data concerning bacteriophage production, processing, administration and dosing, as well as follow-up clinical monitoring reports. To overcome these challenges, an integrated clinical approach is required, supported by comprehensive legislature to enable expansive and correctly implemented clinical trials. ispartof: EUROPEAN CELLS & MATERIALS vol:39 pages:193-210 ispartof: location:Switzerland status: published

3D printing is often discussed in the field of hand rehabilitation, yet many hand therapists are unaware of this technology and how it either is used or could potentially be used in rehabilitation. To shed some light on the state of 3D printing in hand rehabilitation, we sought insight from a rehabilitation engineer, occupational therapy educator, clinician, and hospital administrator to provide a comprehensive look at the state of 3D printing today.

The Physician-Payments-Sunshine-Act (PPSA) was introduced in 2010 to provide transparency regarding physician-industry payments by making these payments publicly available. Given potential ethical implications, it is important to understand how these payments are being distributed, particularly as the women orthopaedic workforce increases. The purpose of this study was thus to determine the role of gender and academic affiliation in relation to industry payments within the orthopaedic subspecialties.The PPSA website was used to abstract industry payments to Orthopaedic surgeons. The internet was then queried to identify each surgeon's professional listing and gender. Mann-Whitney U, Chi-square tests, and multivariable regression were used to explore the relationships. Significance was set at a value of P 0.05.In total, 22,352 orthopaedic surgeons were included in the study. Payments were compared between 21,053 men and 1299 women, 2756 academic and 19,596 community surgeons, and across orthopaedic subspecialties. Women surgeons received smaller research and non-research payments than men (both, P 0.001). There was a larger percentage of women in academics than men (15.9% vs 12.1%, P 0.001). Subspecialties with a higher percentage of women (FootAnkle, Hand, and Pediatrics) were also the subspecialties with the lowest mean industry payments (all P 0.001). Academic surgeons on average, received larger research and non-research industry payments, than community surgeons (both, P 0.001). Multivariable linear regression demonstrated that male gender (P = 0.006, P = 0.029), adult reconstruction (both, P 0.001) and spine (P = 0.008, P 0.001) subspecialties, and academic rank (both, P 0.001) were independent predictors of larger industry research and non-research payments.A large proportion of the US orthopaedic surgeon workforce received industry payments in 2014. Academic surgeons received larger payments than community surgeons. Despite having a larger percentage of surgeons in academia, women surgeons received lower payments than their male counterparts. Women also had a larger representation in the subspecialties with the lowest payments.

To highlight the most relevant contributions of the Italian Renaissance surgeon Girolamo Fabrizi d’Acquapendente in the field of orthopaedics and traumatology. An extensive research on the life and achievements of Girolamo Fabrizi was conducted on University Libraries as well as on electronic databases like PubMed. Girolamo Fabrizi d’Acquapendente is known for his embryology and physiology studies, particularly on sensory organs and blood circulation. He founded the world’s first permanent anatomical theater established at the University of Padua and inaugurated in 1595. His most notable publications include surgical and definitely orthopedics works such as “De fracturis” (On fractures) and “De luxationibus” (On joint displacement). He outlined some principles of treatment that are still valid nowadays such as anatomical reduction and stabilization of the fracture, that were applied using the equipment available at that time. He described and illustrated maneuvers and instruments, such as pulleys, winches, splint, and bandages. He further depicted the famous “Oplomochlion” (“the armored man”), which is actually a collection of all of the braces used at the time to correct congenital and post-traumatic deformities. Bracing and prosthetic replacements have accompanied medical history throughout the centuries, from Ancient Egypt to the present, but it was the ingenuity of Renaissance surgeons that pushed biomedical technology to new heights: Girolamo Fabrizi d’Acquapendente was one of the most illustrious contributors to these great achievements.

Objective To classify patients with stroke into subgroups based on their characteristics at the moment of discharge from inpatient rehabilitation in order to predict community ambulation outcome 6 months later. Design Prospective cohort study with a baseline measurement at discharge from inpatient care and final outcome determined after 6 months. Setting Community. Participants A cohort of patients (N=243) with stroke, referred for outpatient physical therapy, after completing inpatient rehabilitation in The Netherlands. Interventions Not applicable. Main Outcome Measures A classification model was developed using Classification And Regression Tree (CART) analysis. Final outcome was determined using the community ambulation questionnaire. Potential baseline predictors included patient demographics, stroke characteristics, use of assistive devices, comfortable gait speed, balance, strength, motivation, falls efficacy, anxiety, and depression. Results The CART model accurately predicted independent community ambulation in 181 of 193 patients with stroke, based on a comfortable gait speed at discharge of 0.5 meters per second or faster. In contrast, 27 of 50 patients with gait speeds below 0.5 meters per second were correctly predicted to become noncommunity walkers. Conclusions We show that comfortable gait speed is a key factor in the prognosis of community ambulation outcome. The CART model may support clinicians in organizing community services at the moment of discharge from inpatient care.

Bone milling force is a key factor to be controlled during the orthopedic surgery. Cutting force has significant influence on the breaking of the tools or causing bone cracks. The cutting force depends on machining parameters, cutting tools and the cortical bone tissue. In this paper, rotational speed, feed rate, cutting depth, tool diameter and the osteon orientation are considered as input parameters. For statistical modeling and experimental study, the response surface method was used. Moreover, using the Sobol statistical sensitivity analysis method the effect of each input parameter on the process force is investigated both qualitatively and quantitatively. Results revealed that bone milling force decreases with increasing rotational speed while it increases with feed rate due to an increase in the thickness of the deformed chip as well as an escalation of friction. Moreover, increasing cutting depth due to increased thickness of the deformed chip, increases friction and thus increases cutting force. Additionally, as the diameter of the blade increases, the cutting force increases. Finally, in the perpendicular direction to the osteon, less force is applied to the bone tissue than that of parallel to osteon. Based on Sobol sensitivity analysis, cutting depth (51.4%), feed rate (21.9%), tool rotational speed (19%), milling direction (4.8%) and tool diameter (1.9%) are the most effective respectively. Response optimization was also presented using Derringer algorithm, which provided a minimum cutting force of 3.76 N, when tool diameter of 4 mm, rotational speed of 3000 rpm and feed rate of 100 mm/min and cutting depth of 1 mm were selected in milling perpendicular to the osteon orientation. This research can be used to optimize milling parameters in order to assist robotic surgery and orthopedic tool design.

Orthopaedic hardware explantation is a multifaceted topic with complex legal, ethical, and scientific aspects that require thorough exploration. Issues of device ownership, explant-induced disease propagation, and potential device resale pose legal risks to providers and health-care institutions. Ethically, implant removal highlights the potential that performing procedures at the request of the patient will incentivize patient compliance and strengthen the patient-surgeon relationship. However, the return of explanted hardware to patients could hinder scientific study and innovation, ultimately limiting advancement in risk reduction and patient outcomes. Continued research into these topics remains paramount to ensure that clinicians and institutions deliver optimal patient care while abiding with legal and ethical imperatives. This article addresses the legal, ethical, and scientific issues that are pertinent to returning an explanted orthopaedic implant to the patient and the potential ramifications of such practice.

Purpose We assess feasibility of wearable gait analysis in geriatric wards by testing the effectiveness and acceptance of the system. Methods Gait parameters of 83 patients (83.34 ± 5.88 years, 58/25 female/male) were recorded at admission and/or discharge to/from two geriatric inpatient wards. Gait parameters were tested for statistically significant differences between admission and discharge. Walking distance measured by a wearable gait analysis system was correlated with distance assessed by physiotherapists. Examiners rated usability using the system usability scale. Patients reported acceptability on a five-point Likert-scale. Results The total distance measures highly correlate (r = 0.89). System Usability Scale is above the median threshold of 68, indicating good usability. Majority of patients does not have objections regarding the use of the system. Among other gait parameters, mean heel strike angle changes significantly between admission and discharge. Conclusion Wearable gait analysis system is objectively and subjectively usable in a clinical setting and accepted by patients. It offers a reasonably valid assessment of gait parameters and is a feasible way for instrumented gait analysis.

I am sure Jerry Lee Lewis would excuse my witticism with the title of his famous rock ’n roll song. However, it depicts metaphorically that radiostereometric analysis (RSA) has become even more of ...

BACKGROUND Frankly dislocated hips occur in ∼1% to 3% of infants with developmental dysplasia of the hip and are often difficult to treat. In the most severely dislocated hips, the femoral head is positioned outside the posterior/lateral rim of the acetabulum and is irreducible, that is, the femoral head will not reduce by positioning the leg. The purpose of this study was to determine risk factors, using univariate and multivariate analyses, for Pavlik harness failure in infants who initially presented with irreducible/dislocated hips (confirmed by dynamic sonography). METHODS Following institutional review board approval, 124 infants (170 hips) with frankly dislocated hips treated using a Pavlik harness between 2000 and 2018 were evaluated. Patients' demographic characteristics, clinical findings, dynamic sonographic findings (dislocated-fixed vs. dislocated-mobile), age at onset of Pavlik harness treatment, duration of harness usage, and follow-up treatments were recorded. Univariate analyses were used to determine risk factors for treatment failure. RESULTS In frankly dislocated hips (confirmed by dynamic sonography to be positioned outside the posterior/lateral rim of the acetabulum), Pavlik harness treatment was successful in 104 of 170 hips (61%) while it failed in 66 hips. Mean follow-up was 4.86±4.20 years. Univariate analysis determined the risk factors to be onset of treatment after the seventh week of age (P=0.049) and initial mobility (dislocated-fixed group) (P

INTRODUCTION The success of Pavlik harness therapy is based, among other things, upon the correct reapplication by parents. This prospective study assesses the effectiveness of a validated Objective Structured Assessment of Technical Skill (OSATS) educational module for Pavlik harness application among Greek parents. METHODS Forty consecutive parents of newborns with developmental dysplasia of the hip (DDH), who were treated with Pavlik harness, were divided into two groups. Twenty parents (group 1) were educated with the Greek OSATS version, while the rest (group 2) served as the control. The OSATS score, quality of the final product (Global Rating Scale - GRS) and sonographic imaging of the hips were evaluated during follow-up. RESULTS Post-intervention evaluation revealed significant higher means of OSATS score (p

This article reports for the first time our successful result in the synthesis of antibacterial single-phase newberyite (NB, MgHPO4 .3H2 O), an important magnesium phosphate (MgP) bioceramic. The prime novelty lies in the fact that we explore novel MgPs as next-generation orthopedic biomaterials as opposed to conventional calcium phosphates (CaP). While NB has already shown great promise, unlike its competitor struvite (ST, MgNH4 PO4 .6H2 O), NB is not intrinsically antibacterial. Given the havoc created by surgical site infections (SSI) in orthopedics, it would be worthwhile to explore if antibacterial NB can be synthesized cost-effectively. To accomplish that central goal, we used silver ion (Ag+ ) containing precursor solutions and exposed those to microwave irradiation. This action resulted in the rapid synthesis of NB microplatelets. Besides, three other specific objectives are addressed. First, Ag-doping was optimized to preserve the single-phase nature for sustained dopant release. Second, Ag+ release kinetics against common infection causing bacterial strains was analyzed. Finally, we inspected for any harmful effect of Ag-doped NB on MC3T3 preosteoblasts. Interestingly, the single-phase nature of NB microplatelets can be retained until 2 wt % Ag-doping and they exhibit good antibacterial and cytocompatible properties. Even though 3 wt % Ag-doped compositions (composites) were 100% antibacterial; they were cytotoxic.

Purpose To compare clinical and radiological outcomes, including tunnel widening, and to evaluate graft status by second-look arthroscopy after anterior cruciate ligament (ACL) reconstruction using 2 different femoral cortical suspension devices (fixed and adjustable loop). Methods Seventy-nine patients were included for this study. The patients were divided into 2 groups, 41 patients of fixed loop group (EndoButton) and 38 patients of adjustable loop group (TightRope). The Tegner activity, Lysholm knee score, Lachman test, and pivot-shift test were compared between the 2 groups. Anterior stress radiographs and femoral tunnel widening on plain radiographs were also compared. Twenty-seven patients (66%) in the EndoButton group and 21 patients (55%) in the TightRope group underwent the second-look arthroscopy. Results At the final follow-up, the mean Tegner activity, Lysholm, and International Knee Documentation Committee scores were improved in both groups and there were no statistically significant differences (5.1 ± 1.6 and 5.5 ± 2.1, P = .312; 90.4 ± 7.8 and 91.0 ± 6.5, P = .525; and 87.4 ± 6.7 and 88.7 ± 5.3, P = .127, respectively). There were no statistical significances in the both groups in terms of Lachman test and pivot-shift tests (P = .392, .559) as well as anterior stress radiographs (mean 3.2 ± 1.4 mm and 2.9 ± 1.1 mm, P = .343). Moreover, radiologic measurements comparing femoral tunnel widening at proximal and distal half also showed no significant differences (P = .540 and .412 on anteroposterior view; P = .254 and .437 on lateral view). In the second-look arthroscopy findings for graft tear and synovial coverage, there were no significant differences (P = .784 and .897). Conclusions Both fixed loop and adjustable loop devices in ACL reconstruction provided good clinical and radiological outcomes. In patients with both devices, femoral tunnel widening at proximal and distal portion have no significant differences after ACL reconstruction. Moreover, second-look arthroscopy revealed no significant differences in terms of synovial coverage and rupture of the graft. Level of Evidence Level II, prospective comparative study.

The multifunctional biological active material design for bone tissue engineering is essential to induce osteoblast cell proliferation and attachment. Adhesion of bacteria on biomaterials to produce biofilms can be major contributors to the pathogenesis of implant material associated infections. This research work focuses on NPF& NBF elemental doping and functionalization of reduced graphene oxide using an imidazolium-based ionic liquid such as BMIM PF6 and BMIM BF4 by hydrothermal method. The resulting tri doped reduced graphene oxide (NPF-rGO and NBF-rGO) composite was further used as a scaffold for bone tissue engineering and anti-biofilm activities. The observation of the effect of NPF-rGO and NBF-rGO on the morphology, adhesion and cell proliferation of HOS cell was investigated. Moreover, the tri doped composite tested its antibiofilm properties against B. subtilis, E. coli, K. pneumoniae, and P. aeruginosa pathogenic bacteria. In-vitro studies clearly show the effectiveness of N, P, B, and F doping promoting the rGO mineralization, biocompatibility, and destruction of bacterial biofilm formation. The result of this study suggests that NPF-rGO and NBF-rGO hybrid material will be a promising scaffold for bone reaeration and implantation with a minimal bacterial infection.

INTRODUCTION Autologous bone graft is the gold standard for filling bone defects associated with diaphyseal nonunions. It is typically harvested from the anterior iliac crest (AIC) despite the high complication rate. The Reamer/Irrigator/Aspirator System (RIA) was developed to recover the reaming aspirate and use it as autograft. Initially described for harvesting bone from the femur, the bone volume available is similar to the AIC site; however, its use directly at nonunion sites has been studied very little. HYPOTHESES Compared to AIC harvesting, RIA at a non-union site will result in (1) sufficient bone volume, (2) similar time to union and union rate, (3) lower morbidity. RESULTS Two groups of patients received an autograft for aseptic nonunion of the tibia or femur for a bone defect up to 2cm: the RIA group (n=30) was followed prospectively and received an autograft by RIA while the AIC group (n=29) was reviewed retrospectively and received an autograft by AIC. We compared the time to union and union rate, operative time, intake of analgesics, duration of hospital stay and complication rate between groups. The RIA provided sufficient bone, 60cm3 on average in a reliable manner. The union rate was similar between groups: 90% (RIA) and 89.7% (CIA) (p=0.965), while the time to union was shorter in the RIA group (8.63±1.47months vs. 10.08±1.7 months) (p=0.006). The operative time (p

Despite evidence that instability of the first ray (first metatarsal and medial cuneiform) alters the loading mechanics of the foot, surprisingly few studies have linked the condition with disorders of the foot. A factor limiting this research is the difficulty associated with measuring first ray mobility (FRM). To quantify dorsal FRM, clinicians and researchers have devised a variety of methods that impose a dorsally directed load, and record displacement. The methods include manual examination, radiographs, mechanical devices, and handheld rulers. Since different methods yield different results; each of these methods is worthy of scrutiny. This article reviews the methods used to quantify dorsal FRM and offers commentary on how the testing procedures could be standardized. The measurement of dorsal FRM informs surgical decisions, orthotic prescriptions, and research design strategies mostly as it pertains to the identification and treatment of first ray hypermobility. This review found sufficient support to recommend continued use of radiographs and mechanical devices for quantifying dorsal displacement, whereas measurements acquired with handheld rulers are prone to the same subjective error attributed to manual examination procedures. Since measures made with radiographs and existing mechanical devices have their own drawbacks, the commentary recommends ideas for standardizing the testing procedure and calls for the development of a next-generation device to measure dorsal FRM. This future device could be modeled after arthrometers that exist and are used to quantify stability at the knee and ankle. Level of Evidence: Level V, expert opinion.

Many older adults require assistive technology to maintain mobility (e.g., canes, walkers, wheelchairs, or scooters), but concerns about experiencing prejudice because of mobility devices can deter use. We explore this potential prejudice in a sample recruited through online crowdsourcing. Overall, prejudice toward older adult mobility device users was not observed. Older adult mobility device users were evaluated more positively than common prejudice target groups. However, heightened prejudice toward older adult mobility device users was observed among those higher in authoritarianism or social dominance orientation. This was explained by perceptions that older adult mobility device users are a greater threat to resources (e.g., health care spending, time, attention) among those higher in these qualities. This pattern was present at all ages assessed but was stronger for those who were younger versus older. Relationships between ideology and heightened threat from older adult mobility device users were not present for those older than 60 years of age. Our results demonstrate that concerns about this prejudice are not completely unwarranted. (PsycINFO Database Record (c) 2019 APA, all rights reserved).

Background The mechanical parameters of the Ilizarov fixator are influenced by many factors related to its spatial configuration. The aim of this study was to experimentally evaluate the impact of the type of implant and the number of distraction rods on the uniformity of loading of distraction rods and stiffness coefficients of the Ilizarov fixator. Methods The tests were carried out on a physical model. The model was mounted in a universal loading station MTS 858 Mini Bionix. Forces in distraction rods are measured with the use of strain gauge force transducers. Displacements of bone fragments were measured by means of digital image correction. Findings In the case of a fixator with 3 distraction rods, configuration of implants has no statistically significant effect on the forces occurring in distraction rods. In the case of a fixator with 4 distraction rods, there are statistically significant differences in the forces in distraction rods. The highest transverse stiffness coefficients occurs in the system with 4 distraction rods and the configuration of 1K1S implants, while the smallest transverse stiffness coefficients occurs in the fixator with 4 distraction rods and the configuration of 0K1S implants. Interpretation Based on the results of experiments on the physical model, we observed an asymmetry in the distribution of forces transmitted through distraction rods. The configuration with 3 distraction rods provides more uniform distribution of forces in distraction rods and reduces the impact of the implant configuration on transverse stiffness coefficients. The use of a configurations with 4 rods may be advantageous when we want to obtain greater transverse stiffness coefficients of a system consisting of the fixator and fragments of the lengthened bone.

Background Posterior dynamic stabilization systems are developed to maintain the healthy biomechanics of the spine while providing stabilization. Numerous dynamic systems incorporate polycarbonate urethane with temperature- and moisture-dependent material properties. In the underlying study, a novel test rig is used to evaluate the biomechanical performance of a system containing polycarbonate urethane. Methods The test rig is composed of two hydraulic actuators. An environmental chamber, filled with water vapor at body temperature, is included in the set up. The translational and rotational degrees of freedom of vertebrae and pedicle screws are measured using a magnetic tracking system. The Transition® device is tested in five lumbar spines (L2–L5) of human cadavers. Pure moment tests are performed for flexion-extension, lateral bending, and axial rotation. Three test conditions are compared: 1. native specimens, 2. dynamic instrumentation at L4–L5, 3. dynamic instrumentation with decompression at L4–L5. Findings The ranges of motion, the centers of rotation, and the pedicle screw loosening are calculated and evaluated. During daily motions such as walking, the loads on the lumbar spine differ from the standardized test protocols. To allow a reproducible data evaluation for smaller deformations, all moment-rotation curves are parameterized using sigmoid functions. Interpretation In flexion-extension, the Transition® device provides the highest stiffening of the segment and the largest shift of the center of rotation. No shift in the center of rotation, and the smallest supporting effect on the segment is observed for axial rotation. In lateral bending, a mediate reduction of the range of motion is observed.