Search

In order to obtain the target frequency in operation, the resonant frequency of superconducting radiofrequency cavities is controlled and adjusted from the manufacturing to the end of preparation phase. Reaching this right frequency can be challenging due to the narrow frequency range defined by the tuning sensitivity of the cavity and the capability of the tuner. Mechanical deformation until plasticity is attained is of great interest to tune SRF cavities when large frequency shift is needed. But once a cavity is dressed with its helium tank, the only accessible part is its beam pipe, reducing the mechanical action to a push/pull action. This limited possibility has hence to be skilfully associated with chemical etching. An original mechanical tuning of Spoke dressed cavities consists in increasing the pressure inside the helium tank to induce a permanent deformation of the cavity walls. The frequency shift induced by nonlinear deformation is numerically evaluated in order to determine the pressure increments. Both methods were successfully performed on the cavities of the ESS accelerator and of the Myrrha project., Proceedings of the 12th International Particle Accelerator Conference, IPAC2021, Campinas, SP, Brazil

PERLE is a proposed high power Energy Recovery Linac, designed on multi-turn configuration, based on SRF technology, to be hosted at Orsay-France in a col-laborative effort between local laboratories: LAL and IPNO, together with an international collaboration involv-ing today: CERN, JLAB, STFC ASTeC Daresbury, Liverpool University and BINP Novosibirsk. PERLE will be a unique leading edge facility designed to push advances in accelerator technology, to provide intense and highly flexible test beams for component development. In its final configuration, PERLE provides a 500 MeV elec-tron beam using high current (20 mA) acceleration during three passes through 801.6 MHz cavities. This presenta-tion outlines the technological choices, the lattice design and the main component descriptions., Proceedings of the 10th Int. Particle Accelerator Conf., IPAC2019, Melbourne, Australia

CEA is in charge of the 30 elliptical medium and high-beta cryomodules to be installed in the ESS tunnel in Lund, Sweden. Before launching the assembly of the series cryomodules, CEA developed a medium-beta cryomodule technology demonstrator in a collaboration with IPNO, LASA and ESS. This paper briefly presents the cryomodule assembly and summarizes the main results of the high RF power tests performed in 2018 in a dedicated test stand in CEA Saclay. The main ESS requirements were reached: E_{acc} = 16.7 MV/m in cavities, Pforward = 1.1 MW in power couplers, RF pulses length = 3.6 ms at 14 Hz. The piezo tuners efficiently compensated the Lorentz forces detuning and could stabilize the accelerating field better than 1% over the full length of the expected ESS 2.86 ms beam pulse without any LLRF regulation system. Following this successful validation CEA started the assembly of the first ESS medium-beta series cryomodule, Proceedings of the 10th Int. Particle Accelerator Conf., IPAC2019, Melbourne, Australia

PERLE (Powerful ERL for Experiments) is a novel ERL test facility, initially proposed to validate choices for a 60 GeV ERL foreseen in the design of the LHeC and the FCC-eh. Its main thrust is to probe high current, CW, multi-pass operation with superconducting cavities at 802 MHz (and perhaps testing other frequencies of interest). With very high virtual beam power (~ 10 MW), PERLE offers an opportunity for controllable study of every beam dynamic effect of interest in the next generation of ERL design; becoming a ‘stepping stone' between present state-of-art 1 MW ERLs and future 100 MW scale applications. PERLE design features Flexible Momentum Compaction lattice architecture for six vertically stacked return arcs and a high-current, 6 MeV, photo-injector. With only one pair of 4 cavity cryomodules, 400 MeV beam energy can be reached in 3 re-circulation passes, with beam currents in excess of 15 mA. The beam is decelerated in 3 consecutive passes back to the injection energy, transferring virtually stored energy back to the RF. This unique facility will serve as a test-bed for high current ERL technologies, as well as a user facility in low energy electron and photon physics., Proceedings of the 9th Int. Particle Accelerator Conf., IPAC2018, Vancouver, BC, Canada

Two ESS elliptical cavities cryomodule prototypes are being developed and will be tested at CEA Saclay before starting the series production. This paper presents the preliminary test results of the first medium beta cavities cryomodule demonstrator M-ECCTD. The measurements of the cryogenic performances at 80 K and 2 K of the different cryomodule components and circuits are given. The first RF test results performed at low power are also reported., Proceedings of the 9th Int. Particle Accelerator Conf., IPAC2018, Vancouver, BC, Canada

CEA Saclay in collaboration with IPN Orsay is in charge of the ESS elliptical cavities cryomodule design, prototyping and series production. Two cryomodule prototypes are being developed and will be tested at CEA Saclay before starting the series production. The main cryomodule design features are first reminded. We present the cavities and couplers test results and the achieved assembly sequences of the first medium beta cavities cryomodule demonstrator M-ECCTD. The progress on the preparation of the CEA cryomodule test station is given. The procurement status and development plan of the second high beta demonstrator H-ECCTD are also reported. Finally we give the components procurement progress and the assembly strategy of the 30 series cry-omodules to be integrated at CEA before delivery to ESS at Lund., Proceedings of the 18th Int. Conf. on RF Superconductivity, SRF2017, Lanzhou, China

The first ESS prototype cryomodule with medium beta cavities named M-ECCTD is being assembled at CEA Saclay. The Q curves of the 4 cavities mounted inside the cryomodule are presented, and the four power couplers have been conditioned at high power before their assembly onto the cavity string. Completion of the M-ECCTD assembly outside clean room is in progress as well as the finalization of the RF power test stand preparation. RF power tests of the M-ECCTD will be performed during summer 2017. CEA is preparing the production of the ESS medium and high beta cryomodules of the series before the test of the M-ECCTD and the contracts for the procurement of the most critical components have already been signed, Proceedings of the 8th Int. Particle Accelerator Conf., IPAC2017, Copenhagen, Denmark

The European Spallation Source requires a pulsed Linac with an average beam power on the target of 5MW which is about five times higher than the most powerful spallation source in operation today. Over 97% of the acceleration occurs in superconducting cavities. ESS will be the first accelerator to employ double spoke cavities to accelerate beam. Accelerating gradients of 9MV/meter is required in the spoke section. The spoke section will be followed by 36 elliptical 704 MHz cavities with a geometrical beta of 0.67 and elliptical 704 MHz cavities with a geometrical beta of 0.86. Accelerating gradients of 20MV/m is required in the elliptical section. Initial gradient test results will be presented in which results exceed expected requirements., Proceedings of the 28th Linear Accelerator Conf., LINAC2016, East Lansing, MI, USA

The concept of partitioned kernel, introduced by the Integrated Modular Avionics (IMA) architecture comes with new challenges (isolation enforcement, partitioning trade-off, etc.) that must be addressed during the design and the implementation of partitioned architectures. However, the development process frequently consists in handwriting code, which makes difficult the analysis of the system. Such a development process does not ease the design of high-integrity systems. Model Based Engineering describes architecture and application requirements with models. Models can be then used to ensure requirements enforcement or produce code, ensuring that requirements are enforced inside the implementation. In this paper, we claim the Architecture Analysis and Design Language (AADL) as a valuable candidate to support a Model-Based method for the design and the implementation of ARINC653 systems. Using the AADL as a backbone language, we model such architectures using first-class citizen AADL constructs (virtual processors and buses) and detail their validation. We present our code generator that automatically assembles, configures and deploys application code from AADL models. We also discuss the efficiency of a model-based approach in the design of certifiable systems and explain how it helps the system integrator to certify its system. INTRODUCTION

The European Spallation Source (ESS) accelerator is a large superconducting linac under construction in Lund, Sweden. A collaboration between CEA Saclay, IPN Orsay and ESS-AB is established to design the elliptical cavities cryomodule of the linac. It is foreseen to build and test two cryomodule demonstrators within the next two years. We present the design evolution and the fabrication status of the cryomodule components housing four cavities. The latest test results of two prototype cavities are shown. The cryomodule assembly process and the on-going testing infrastructures at CEA Saclay are also described., Proceedings of the 17th International Conference on RF Superconductivity, SRF2015, Whistler, BC, Canada

Two prototypes of elliptical superconducting cavities have been designed and manufactured in the frame of the French-Swedish agreement for ESS. These 5-cell cavities have a beta value of 0.86 and their frequency is 704.42 MHz. The nominal accelerating gradient on the ESS accelerator is 19.9 MV/m at 2K. We present the manufacturing status of the cavities by two different vendors as well as the specific means which have been developed for the cavity treatments performed at CEA after delivery. We emphasis the activities performed on the first bare cavities recently received at CEA such as the RF measurement and tuning operations, the cleaning and chemical treatments and the clean room assembly including high pressure rinsing. Finally, first test results at 2K in vertical cryostat are reported., Proceedings of the 5th Int. Particle Accelerator Conf., IPAC2014, Dresden, Germany

Model Driven Engineering provides facilities to tackle complexity in real-time systems, from early requirements capture to validation & verification down to code generation. We note that models are built from a system perspective, and resources are allocated to meet communication, energy or scheduling constraints. Yet, it is seldom optimal. In this paper, we explore transformations applied at model-level that preserve schedulability of the system, yet reduce the overall resource consumption. We use AADL as input formalism. By automating this process, we show how to transition from a system view to an implementation view, closer to actual hardware constraints.

Indexing and retrieving data by location and time allows people to share and explore massive geotagged datasets observed on social networks such as Facebook, Flickr, and Twitter. This scenario known as a Location Based Social Network (LBSN) is composed of millions of users, sharing and performing location-temporal range queries in order to retrieve geotagged data generated inside a given geographic area and time interval. A key challenge is to provide a scalable architecture that allow to perform insertions and location-temporal range queries from a high number of users. In order to achieve this, Distributed Hash Tables (DHTs) and the Peer-to-Peer (P2P) computing paradigms provide a powerful building block for implementing large scale applications. However, DHTs are ill-suited for supporting range queries because the use of hash functions destroy data locality for the sake of load balance. Existing solutions that use a DHT as a building block allow to perform range queries. Nonetheless, they do not target location-temporal range queries and they exhibit poor performance in terms of query response time and message traffic. This thesis proposes two scalable solutions for indexing and retrieving geotagged data based on location and time.; La recherche et l'indexation de données en fonction d'une date ou d'une zone géographique permettent le partage et la découverte d'informations géolocalisées telles que l'on en trouve sur les réseaux sociaux comme Facebook, Flickr, ou Twitter. Cette réseau social connue sous le nom de Location Based Social Network (LBSN) s'applique à des millions d'utilisateurs qui partagent et envoient des requêtes ciblant des zones spatio-temporelles, permettant d'accéder à des données géolocalisées générées dans une zone géographique et dans un intervalle de temps donné. Un des principaux défis pour de telles applications est de fournir une architecture capable de traiter la multitude d'insertions et de requêtes spatio-temporelles générées par une grande quantité d'utilisateurs. A ces fins, les Tables de Hachage Distribué (DHT) et le paradigme Pair-à-Pair (P2P) sont autant de primitives qui forment la base pour les applications de grande envergure. Cependant, les DHTs sont mal adaptées aux requêtes ciblant des intervalles donnés; en effet, l'utilisation de fonctions de hachage sacrifie la localité des données au profit d'un meilleur équilibrage de la charge. Plusieurs solutions ajoutent le support de requêtes ciblant des ensembles aux DHTs. En revanche ces solutions ont tendance à générer un nombre de messages et une latence élevée pour des requêtes qui ciblent des intervalles. Cette thèse propose deux solutions à large échelle pour l'indexation des données géolocalisées.