526 results on '"Nishimura, Toshiyuki"'
Search Results
2. Degradation of carbon fiber-reinforced ultra-high-temperature ceramic matrix composites at extremely high temperature using arc-wind tunnel tests
3. Corrosion behavior of Al4SiC4/SiC ceramics exposed to molten calcium‐magnesium‐alumino‐silicate at 1350°C in air
4. Characterization of carbon fiber-reinforced ultra-high temperature ceramic matrix composites fabricated via Zr-Ti alloy melt infiltration
5. Measurement of the in-plane coefficient of thermal expansion of ceramic protective coatings from room temperature to 1400 °C
6. Corrosion behavior of Al4SiC4/SiC ceramics exposed to molten calcium‐magnesium‐alumino‐silicate at 1350°C in air.
7. Thermal stability of the CoWO4 layer formed on ferritic stainless steel
8. Fabrication of dense ZrB2/B4C composites using pulsed electric current pressure sintering and evaluation of their high-temperature bending strength
9. Correlation analysis between microstructure and mechanical properties of spark-plasma-sintered Ti(C, N)–W cermets according to changes in titanium, carbon and nitrogen contents
10. Uniform and fine Mg-γ-AlON powders prepared from MgAl2O4: A promising precursor material for highly-transparent Mg-γ-AlON ceramics
11. Enhanced high-temperature strength of HfB2–SiC composite up to 1600°C
12. A method for testing the interface toughness of ceramic environmental barrier coatings (EBCs) on ceramic matrix composites (CMCs)
13. Grain Boundary Control to Obtain Heat-Resistant Silicon Nitride
14. Preparation of Nanosize Silicon-Nitride-Based Ceramics and Their Superplasticity
15. Microstructure and high-temperature strength of silicon carbide with 2000 ppm yttria
16. Spark plasma sintering of silicon nitride using nanocomposite particles
17. Introduction: Deformation of Silicon Nitride at High Temperatures
18. Pulverization of oxide powders utilizing thermal treatment in ammonia-based atmosphere
19. High-temperature strength of a thermally conductive silicon carbide ceramic sintered with yttria and scandia
20. Transmission Electron Microscopy–Energy-Dispersive X-Ray Spectroscopy Analyses and High-Temperature Compression Tests of Spark-Plasma-Sintered Ti(C, N)–W Cermets with Some Different Ti, C and N Contents
21. Reply to the ‘Comment on “Insight of the preponderant role of the lattice size in the Sn-based colusite for promoting high power factor”’ by E. Guilmeau (J. Mater. Chem. A, 2023, DOI: 10.1039/D2TA03048A)
22. High-strength TiB2–TaC ceramic composites prepared using reactive spark plasma consolidation
23. Electrical and thermal properties of silicon carbide–boron nitride composites prepared without sintering additives
24. Densification, microstructure evolution and mechanical properties of WC doped HfB2–SiC ceramics
25. Electrical and thermal properties of SiC–AlN ceramics without sintering additives
26. Fabrication of dense B4C/CNF composites having extraordinary high strength and toughness at elevated temperatures
27. Conclusions
28. Machinable ZrB2–SiC–BN composites fabricated by reactive spark plasma sintering
29. Consideration of the formation mechanism of an Al2O3-HfO2 eutectic film on a SiC substrate
30. Preparation and electrical properties of Li–Si–Al–O–N ceramics
31. High temperature strength of silicon carbide sintered with 1 wt.% aluminum nitride and lutetium oxide
32. High-temperature bending strength, internal friction and stiffness of ZrB2–20 vol% SiC ceramics
33. Effect of Al4SiC4 additive on the densification of β-silicon carbide under vacuum
34. Insight into the preponderant role of the lattice size in Sn-based colusites for promoting a high power factor
35. Simultaneous Synthesis and Sintering of Dense B4C/CNF Composites using a Pulsed Electric-Current Pressure Sintering and Evaluation of Their Thermal Properties
36. Synthesis of Ca-α-SiAlON phosphors by a mechanochemical activation route
37. Chemothermal pulverization: Crushing titanate crystals to obtain nanosized powders via high‐temperature treatment
38. Induction Heating-Assisted Combustion Synthesis and Mechanical Properties of Al4SiC4 Ceramics
39. Microstructure and thermoelectric properties of Y x Al y B14 samples fabricated through the spark plasma sintering
40. Grain Boundary Control to Obtain Heat-Resistant Silicon Nitride
41. Introduction: Deformation of Silicon Nitride at High Temperatures
42. Conclusions
43. Fabrication of Heat-Resistant and Plastic-Formable Silicon Nitride
44. Preparation of Nanosize Silicon-Nitride-Based Ceramics and Their Superplasticity
45. Microstructure and properties of ZrB 2–SiC composites prepared by spark plasma sintering using TaSi 2 as sintering additive
46. Chemical composition and microstructure of Al 3BC 3 prepared by different densification methods
47. Synthesis, microstructure and mechanical properties of (Zr,Ti)B 2-(Zr,Ti)N composites prepared by spark plasma sintering
48. Corrigendum to “Synthesis of bulk silicon oxynitride glass through nitridation of SiO 2 aerogels and determination of Tg ”
49. Deformation‐resistant Ta 0.2 Hf 0.8 C solid‐solution ceramic with superior flexural strength at 2000°C
50. Low temperature thermal expansion, high temperature electrical conductivity, and mechanical properties of Nb 4AlC 3 ceramic synthesized by spark plasma sintering
Catalog
Books, media, physical & digital resources
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.