Search

Abstract Background The aim of this study was to evaluate the phase composition, phase transformation temperatures, bending property, and cyclic fatigue resistance of different heat-treated nickel-titanium (NiTi) rotary instruments with the same tip diameter and taper at room (RT; 25 ± 1 °C) and body (BT; 37 ± 1 °C) temperatures. Methods Five heat-treated NiTi rotary instruments, HyFlex EDM (EDM), HyFlex CM (CM), Vortex Blue (VB), RE file CT (RE) and JIZAI, and a non-heat-treated NiTi rotary instrument (Mtwo) with a size 40, 0.04 taper were investigated. Temperature-dependent phase transformation was examined with differential scanning calorimetry (DSC). The bending loads of the instruments at RT and BT were evaluated using a cantilever-bending test. Cyclic fatigue resistance at RT and BT was measured using a dynamic test, during which the instruments were rotated in combination with a 2-mm back-and-forth motion in an artificial curved canal, and the number of cycles to failure (NCF) was determined. The results were analyzed using two-way repeated measures analysis of variance, a simple main effect test, and the Bonferroni test (α = 0.05). Results DSC results indicated that EDM and Mtwo were primarily composed of martensite/R-phase and austenite, respectively, while the other heat-treated instruments were composed of a mix of martensite/R-phase and austenite at the tested temperatures. Regardless of the temperature setting, the bending loads of heat-treated instruments were significantly lower than those of Mtwo (p 0.05). Conclusions Heat-treated NiTi instruments exhibited lower bending loads and higher NCF values than Mtwo. However, this tendency was less pronounced at BT than at RT, especially in the NCF values of instruments with a mixture of martensite/R-phase and austenite phases at the tested temperatures.

Background: The aim of this study was to evaluate the phase composition, phase transformation temperatures, bending property, and cyclic fatigue resistance of different heat-treated nickel-titanium (NiTi) rotary instruments with the same tip diameter and taper at room (RT; 25 ± 1 °C) and body (BT; 37 ± 1 °C) temperatures. Methods: Five heat-treated NiTi rotary instruments, HyFlex EDM (EDM), HyFlex CM (CM), Vortex Blue (VB), RE file CT (RE) and JIZAI, and a non-heat-treated NiTi rotary instrument (Mtwo) with a size 40, 0.04 taper were investigated. Temperature-dependent phase transformation was examined with differential scanning calorimetry (DSC). The bending loads of the instruments at RT and BT were evaluated using a cantilever-bending test. Cyclic fatigue resistance at RT and BT was measured using a dynamic test, during which the instruments were rotated in combination with a 2-mm back-and-forth motion in an artificial curved canal, and the number of cycles to failure (NCF) was determined. The results were analyzed using two-way repeated measures analysis of variance, a simple main effect test, and the Bonferroni test (α = 0.05). Results: DSC results indicated that EDM and Mtwo were primarily composed of martensite/R-phase and austenite, respectively, while the other heat-treated instruments were composed of a mix of martensite/R-phase and austenite at the tested temperatures. Regardless of the temperature setting, the bending loads of heat-treated instruments were significantly lower than those of Mtwo (p < 0.05). EDM showed the lowest bending loads and highest NCF at both temperatures (p < 0.05). CM, VB, and JIZAI showed significantly higher bending loads at BT than at RT (p < 0.05). The NCF of all the heat-treated instruments, except VB, was lower at BT than at RT (p < 0.05). At BT, the NCF of CM, VB, RE, and JIZAI were not significantly higher than that of Mtwo (p > 0.05). Conclusions: Heat-treated NiTi instruments exhibited lower bending loads and higher NCF values than Mtwo. However, this tendency was less pronounced at BT than at RT, especially in the NCF values of instruments with a mixture of martensite/R-phase and austenite phases at the tested temperatures. [ABSTRACT FROM AUTHOR]

This study investigated the impact of a one-sided radial-landed cross-sectional design of a heat-treated nickel-titanium rotary instrument (JIZAI, MANI, Japan; JZ) on torque/force generation and canal-shaping ability, using an experimental non-landed instrument (non-landed JZ) for comparison. Both instruments had tip sizes of 25 and 0.04 or 0.06 taper and were similar in metallurgy and geometry, except for the presence/absence of a radial land. Twenty J-shaped simulated resin canals were instrumented in a two-instrument single-length sequence using an automated root canal instrumentation device with a torque/force analyzing unit. Pre- and post-instrumentation images of the resin canals were analyzed for canal-centering ability at 0–3 mm from the apex. The mean centering ratio was not significantly different between JZ and non-landed JZ (p > 0.05). In the 2nd instrumentation, JZ showed a significantly smaller torque compared with the non-landed JZ (p < 0.05). Regardless of instrumentation sequence, JZ showed a significantly smaller maximum upward force, representing screw-in force (p < 0.05), and a larger maximum downward force (p < 0.05) than the non-landed JZ. JZ generated smaller screw-in forces and had similar canal-centering ability compared with the non-landed JZ. [ABSTRACT FROM AUTHOR]

Aim: To evaluate how different rotational speeds affect the torque/force generation and shaping ability of rotary root canal instrumentation using JIZAI (MANI, Utsunomiya, Japan) nickel‐titanium instruments in continuous rotation and optimum torque reverse (OTR) motion. Methodology: Mesial root canals of extracted mandibular molars were instrumented up to size 25, 0.04 taper using JIZAI instruments, and anatomically matched canals were selected based on geometric features of the canal [canal volume (mm3), surface area (mm2), length, 15°–20° curvature and radius of curvature (4–8 mm)] after micro‐computed tomographic scanning. An automated root canal instrumentation and torque/force analysing device was programmed to permit a simulated pecking motion (2 s downward and 1 s upward at 50 mm min−1). The selected canals were prepared with size 25, 0.06 taper JIZAI instruments using continuous rotation or OTR motion and further subdivided according to the rotational speed (300 or 500 rpm, n = 10 each). Real‐time clockwise/counterclockwise torque and downward/upward force were recorded using a custom‐made torque/force analysing device. Then, the registered pre‐ and post‐operative micro‐computed tomographic datasets were examined to evaluate the canal volume changes and centring ratios at 1, 3, 5 and 7 mm from the apical foramen. Data were analysed using two‐way analysis of variance or the Kruskal–Wallis test and Mann–Whitney U test with Bonferroni correction (α = 5%). Results: Maximum upward force and clockwise torque were significantly smaller in 500 rpm groups than in 300 rpm groups (P <.05); however, no significant difference was found between continuous rotation and OTR motion (P >.05). OTR motion developed higher maximum counterclockwise torque than continuous rotation (P <.05). Maximum downward force, canal volume changes and centring ratios were not significantly different among all groups (P >.05). There was no file fracture in any of the groups. Conclusions: Under laboratory conditions using JIZAI instruments, a rotational speed of 500 rpm generated significantly lower maximum screw‐in forces and torque values than rotational speed of 300 rpm. Continuous rotation and OTR motion performed similarly in shaping the canals. [ABSTRACT FROM AUTHOR]

This study aimed to evaluate the mechanical properties of contemporary heat-treated nickel-titanium (NiTi) rotary instruments used in the single-length technique [ProTaper Next (PTN), HyFlex EDM (EDM), and JIZAI (JZ)]. Bending loads, cyclic fatigue resistance, torque/force values and canal-centering ratios were evaluated for the three instruments and a non-heat-treated experimental NiTi instrument with the same geometry as JZ (nJZ). EDM and JZ exhibited significantly lower bending load and more cycles to failure compared with nJZ and PTN (p<0.05). PTN and JZ exhibited significantly better centering ability than nJZ and EDM (p<0.05). JZ and nJZ generated significantly smaller upward force and maximum torque than PTN and EDM (p<0.05). Under the present experimental condition, JZ exhibited flexibility and cyclic fatigue resistance comparable to EDM, better maintained the canal curvature than the other instruments, and generated smaller torque and screw-in force than PTN and EDM. [ABSTRACT FROM AUTHOR]

The aim of this review was to provide a detailed literature analysis of torque and force generation during nickel-titanium rotary root canal instrumentation. We followed Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. An electronic search was performed using in PubMed and in journals for articles published in English from 1987 to June 2020 on studies that investigated dynamic torque and force in vivo or in vitro. We assessed article titles and abstracts to remove duplicates, and the titles and abstracts of the remaining articles were screened for eligibility. Full texts were read to verify eligibility by considering predetermined inclusion and exclusion criteria. Fifty-two out of 4096 studies met the inclusion criteria, from which we identified 26 factors that influence torque or force generation. Factors associated with higher torque or force generation and supported by multiple studies with mostly consistent results included convex triangle cross-sectional design, regressive taper, short pitch length, large instrument size, small canal size, single-length preparation technique, long preparation time, deep insertion depth, low rate of insertion, continuous rotation (torque), reciprocating motion (force), lower rotational speed and conventional alloy. However, several factors are interrelated, which obscured the independent effect of each factor, and there was insufficient scientific evidence supporting the influence of some factors. [ABSTRACT FROM AUTHOR]

This study investigated the impact of a one-sided radial-landed cross-sectional design of a heat-treated nickel-titanium rotary instrument (JIZAI, MANI, Japan; JZ) on torque/force generation and canal-shaping ability, using an experimental non-landed instrument (non-landed JZ) for comparison. Both instruments had tip sizes of 25 and 0.04 or 0.06 taper and were similar in metallurgy and geometry, except for the presence/absence of a radial land. Twenty J-shaped simulated resin canals were instrumented in a two-instrument single-length sequence using an automated root canal instrumentation device with a torque/force analyzing unit. Pre- and post-instrumentation images of the resin canals were analyzed for canal-centering ability at 0–3 mm from the apex. The mean centering ratio was not significantly different between JZ and non-landed JZ (p > 0.05). In the 2nd instrumentation, JZ showed a significantly smaller torque compared with the non-landed JZ (p < 0.05). Regardless of instrumentation sequence, JZ showed a significantly smaller maximum upward force, representing screw-in force (p < 0.05), and a larger maximum downward force (p < 0.05) than the non-landed JZ. JZ generated smaller screw-in forces and had similar canal-centering ability compared with the non-landed JZ.

This study aimed to evaluate the influence of a post-machining thermal treatment on canal-centering ability and torque/force generation of reciprocating nickel-titanium instruments. Simulated J-shaped resin canals were prepared with reciprocating instruments sharing identical geometric architecture and with/without post-machining thermal treatment (Reciproc Blue/Reciproc, VDW, Munich, Germany). Using an original automated root canal instrumentation and torque/force analyzing device, files were operated in a combination of reciprocation and up-and-down motion, and torque/force values were monitored. Canal-centering ratios were measured after superimposition of pre- and post-instrumentation images. Compared with Reciproc, Reciproc Blue showed a significantly lower canal-centering ratio (i.e., less deviation; p<0.05) at 0-1 mm from the apex and generated a significantly smaller upward maximum vertical force (p<0.05). Under standardized conditions using the automated device, Reciproc Blue showed better canal-centering ability and reduced screw-in forces than Reciproc, indicating that the post-machining thermal treatment confers superior performance to reciprocating nickel-titanium instruments. [ABSTRACT FROM AUTHOR]

The aim of this review was to provide a detailed literature analysis of torque and force generation during nickel-titanium rotary root canal instrumentation. We followed Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. An electronic search was performed using in PubMed and in journals for articles published in English from 1987 to June 2020 on studies that investigated dynamic torque and force in vivo or in vitro. We assessed article titles and abstracts to remove duplicates, and the titles and abstracts of the remaining articles were screened for eligibility. Full texts were read to verify eligibility by considering predetermined inclusion and exclusion criteria. Fifty-two out of 4096 studies met the inclusion criteria, from which we identified 26 factors that influence torque or force generation. Factors associated with higher torque or force generation and supported by multiple studies with mostly consistent results included convex triangle cross-sectional design, regressive taper, short pitch length, large instrument size, small canal size, single-length preparation technique, long preparation time, deep insertion depth, low rate of insertion, continuous rotation (torque), reciprocating motion (force), lower rotational speed and conventional alloy. However, several factors are interrelated, which obscured the independent effect of each factor, and there was insufficient scientific evidence supporting the influence of some factors.

Objective: The aim of this study was to compare the effect of three different instruments as orifice openers on the cervical dentine thickness of human mandibular first molars, using cone-beam computed tomography (CBCT). Materials and Methods: Fifteen human permanent mandibular first molars were used. The teeth were thoroughly cleaned of any soft or hard tissue deposits using hand and ultrasonic scalers, disinfected by immersion in 5.25% sodium hypochlorite solution for 1 h, and stored in saline and the teeth were aligned in arch form and a pre-operative CBCT was taken. The samples were randomly divided into three equal groups according to the orifice opener used (n = 5). The canals were instrumented using stainless steel hand instruments, Kedo-S file, and ProTaper files. The root canals were scanned after the cervical flaring using the same pre-flaring scanning protocol; cervical dentine thickness was measured before and after flaring. SPSS version 15 software was used to compare between the tested groups and each thickness. Results: For the ProTaper group, the percentage change in mesiobuccal cervical thickness was significantly higher than Kedo-S and stainless steel hand instrument at the level of 2.0 mm and 4 mm below the cervical line. Conclusion: From the present study results, it may be concluded that regarding dentin removal from root canal walls during instrumentation, rotary nickel-titanium ProTaper file was found to be more effective than the other. Hence, further clinical trials are required to confirm the advantages of rotary instruments with regard to the tissue conservation. [ABSTRACT FROM AUTHOR]

Abstract Background/purpose This study evaluated the torsional resistances of nickel-titanium rotary instruments by two methods: i) dynamic resistance: repetitive torsional loading (RTL) and ii) static resistance: single torsional loading (STL) based on the International Organization for Standardization. Materials and methods In RTL method, a pre-set rotational loading (0.5 N cm) was applied after fixing the 3-mm tip of the file, and this clockwise loading to the pre-set torque and counter-clockwise unloading to original position was repeated at 50 rpm until the file fractured. The number of repetition cycles until fracture was counted. In STL method, the torsional strength was determined by continuous clockwise rotation (2 rpm) until fracture. Results from both methods were compared after testing the torsional resistances of four instrument systems (n = 15): Hyflex CM, HyFlex EDM, V-Taper2, and V-Taper2H. A scanning electron microscope (SEM) was used to examine the topographic features of the fractured surfaces and longitudinal aspects (n = 5) from both methods. Results The RTL and STL methods had similar results: V-Taper2 had the highest resistance and the Hyflex CM had the lowest (P < 0.05). Spearman correlation test showed the results from two methods were strongly correlated (coefficient = 1). Under the SEM, specimens from the RTL showed ruptured aspects on cross-sections with multiple areas of crack propagation, while the STL showed the typical features of torsional failure such as circular abrasion marks and fatigue dimples. Conclusions This study suggests the clinically relevant torsional test (RTL) method yield similar results with the STL method, but they have different topographic findings. [ABSTRACT FROM AUTHOR]

Introduction This study compared the effects of pitch length on the torsional resistance and cyclic fatigue resistance of glide path preparation instruments. Methods G-File (G1 and G2; Micro-Mega, Besançon, France) and new generation G-File (NG1 and NG2, Micro-Mega) instruments were compared to evaluate the effects of the shorter pitch of the latter (25% shorter than G-File). G1 and NG1 have a #12 tip size, whereas G2 and NG2 have a #17 tip size. All the files have the same taper of 3%. For comparing the torsional resistances ( n = 15), the file was fixed at 4 mm from the tip, and the clockwise rotation at a constant rotational speed of 2 rpm was adjusted until the file fractured. The maximum torsional load and distortion angle at fracture were recorded. For comparing the cyclic fatigue resistances ( n = 15), the files were freely rotated in a simulated canal (radius, 3 mm; curvature, 90°) at a speed of 300 rpm in a dynamic mode. When the file fractured, the time elapsed was recorded using a chronometer. The number of cycles to failure was calculated by multiplying the total time to failure by the rotation rate. Fractured fragments were examined under the scanning electron microscope. Results The NG2 instruments had significantly higher fatigue resistance and torsional strength than the G2 instruments ( P < .05) and showed approximately the same fatigue resistance as the G1. Scanning electron microscopic examinations revealed the typical appearances of 2 failure modes. Conclusions A shorter pitch design increased cyclic fatigue resistance and torsional strength of the glide path instruments. [ABSTRACT FROM AUTHOR]

Introduction The purpose of the present study was to compare 2 modes of reciprocal movement (torque-sensitive and time-dependent reciprocal rotation) with continuous rotation in terms of torque and apical force generation during nickel-titanium rotary root canal instrumentation. Methods A custom-made automated root canal instrumentation and torque/force analyzing device was used to prepare simulated canals in resin blocks and monitor the torque and apical force generated in the blocks during preparation. Experimental groups ( n = 7, each) consisted of (1) torque-sensitive reciprocal rotation with torque-sensitive vertical movement (group TqR), (2) time-dependent reciprocal rotation with time-dependent vertical movement (group TmR), and (3) continuous rotation with time-dependent vertical movement (group CR). The canals were instrumented with TF Adaptive SM1 and SM2 rotary files (SybronEndo, Orange, CA), and the torque and apical force were measured during instrumentation with SM2. The mean and maximum torque and apical force values were statistically analyzed using 1-way analysis of variance and the Tukey test (α = 0.05). Results The recordings showed intermittent increases of upward apical force and clockwise torque, indicating the generation and release of screw-in forces. The maximum upward apical force values in group TmR were significantly smaller than those in group CR ( P < .05). The maximum torque values in clockwise and counterclockwise directions in groups TqR and TmR were significantly smaller than those in group CR ( P < .05). Conclusions Under the present experimental conditions using TF Adaptive instruments, both torque-sensitive and time-dependent reciprocal rotation generated significantly lower maximum torque and may have advantages in reducing stress generation caused by screw-in forces when compared with continuous rotation. [ABSTRACT FROM AUTHOR]

Introduction This study examined the dynamic fracture behavior of nickel-titanium rotary instruments in torsional or cyclic loading at continuous or reciprocating rotation by means of high-speed digital video imaging. Methods The ProFile instruments (size 30, 0.06 taper; Dentsply Maillefer, Ballaigues, Switzerland) were categorized into 4 groups ( n = 7 in each group) as follows: torsional/continuous (TC), torsional/reciprocating (TR), cyclic/continuous (CC), and cyclic/reciprocating (CR). Torsional loading was performed by rotating the instruments by holding the tip with a vise. For cyclic loading, a custom-made device with a 38° curvature was used. Dynamic fracture behavior was observed with a high-speed camera. The time to fracture was recorded, and the fractured surface was examined with scanning electron microscopy. Results The TC group initially exhibited necking of the file followed by the development of an initial crack line. The TR group demonstrated opening and closing of a crack according to its rotation in the cutting and noncutting directions, respectively. The CC group separated without any detectable signs of deformation. In the CR group, initial crack formation was recognized in 5 of 7 samples. The reciprocating rotation exhibited a longer time to fracture in both torsional and cyclic fatigue testing ( P < .05). The scanning electron microscopic images showed a severely deformed surface in the TR group. Conclusions The dynamic fracture behavior of NiTi rotary instruments, as visualized with high-speed digital video imaging, varied between the different modes of rotation and different fatigue testing. Reciprocating rotation induced a slower crack propagation and conferred higher fatigue resistance than continuous rotation in both torsional and cyclic loads. [ABSTRACT FROM AUTHOR]

Introduction The finite element method (FEM) has been proposed as a method to analyze stress distribution in nickel-titanium (NiTi) rotary instruments but has not been assessed as a method of predicting the number of cycles to failure (NCF). The objective of this study was to predict NCF and failure location of NiTi rotary instruments by FEM virtual simulation of an experimental nonstatic fatigue test. Methods ProTaper Next (PTN) X1, X2, and X3 files (Dentsply Maillefer, Baillagues, Switzerland) ( n = 20 each) were tested to failure using a customized fatigue testing device. The device and file geometries were replicated with computer-aided design software. Computer-aided design geometries (geometric model) were imported and discretized (numeric model). The typical material model of an M-Wire alloy was applied. The numeric model of the device and file geometries were exported for finite element analysis (FEA). Multiaxial random fatigue methodology was used to analyze stress history and predict instrument life. Experimental data from PTN X2 and X3 were used for virtual model tuning through a reverse engineering approach to optimize material mechanical properties. Tuned material parameters were used to predict the average NCF and failure locations of PTN X1 by FEA; t tests were used to compare FEA and experimental findings ( P < .05). Results Experimental NCF and failure locations did not differ from those predicted with FEA ( P = .098). Conclusions File NCF and failure location may be predicted by FEA. Virtual design, testing, and analysis of file geometries could save considerable time and resources during instrument development. [ABSTRACT FROM AUTHOR]

Abstract: Introduction: In cases of failed root canal treatment, endodontic retreatment of the root canal system is necessary. The present study aimed to assess variation in the incidence and depth of residual filling material in dentinal tubules after gutta-percha removal with H-files, the ProTaper Universal System (Dentsply Maillefer, Ballaigues, Switzerland), and the SybronEndo K3 System (SybronEndo Corporation, Orange, CA). Methods: Forty human mandibular premolars with single straight root canals were prepared with K-files (up to size 40) using the step-back technique and filled by cold lateral condensation with gutta-percha and AH Plus sealers (Dentsply DeTrey, Konstanz, Germany). After 1 year, the 40 teeth were divided into one control group and 3 retreatment groups (n = 10 each). Gutta-percha was removed using H-files, the ProTaper Universal System, or the SybronEndo K3 System. The teeth were sectioned, and the incidence and depth of residual filling material in the dentinal tubules were measured under scanning electron microscopy. Results: The depth of filling material in the dentinal tubules did not differ significantly among groups (P > .05). Residual filling material was present in significantly more dentinal tubules in the ProTaper (P = .043) and K3 groups (P = .001) than in the H-file and control groups. Conclusions: The ProTaper Universal System and the SybronEndo K3 System left filling material in a greater proportion of dentinal tubules than did H-files. [Copyright &y& Elsevier]

Aim To compare the efficacy of ProFile rotary Nickel–Titanium (Ni–Ti) instruments and Hedstroem-files (H-files) combined with Gates-Glidden (GG) drills during removal of gutta-percha root fillings used in combination with one of the four representative sealers. Methodology Forty-eight single-rooted human teeth, with fully formed apices and straight root canals were used. The root canals were accessed and instrumented using a stepback technique with H-files. They were randomly assigned to four groups and subsequently filled with a combination of lateral and vertical condensation of gutta-percha and one of the following sealers: Roth 811, AH26, Endion and Roekoseal. The root fillings were removed 1 year later, using either H-files in combination with GG drills or the ProFile Ni–Ti system. Teeth were then grooved longitudinally and split. The amount of gutta-percha and sealer remaining on the root canal walls was traced and scored visually with the aid of a stereomicroscope. The scores were analysed and statistically compared with the Kruskal–Wallis test between the ProFile and H-file groups, as well as among the four sealer subgroups. Two samples from each group were studied under the scanning electron microscope to enhance inspection of canal walls and remaining material. Results Sealer remnants were observed with both techniques mainly in the middle and apical third of the root canal. The ProFile system and the H-files were associated with similar amounts of remaining filling material ( P > 0.05). In the cervical third of the root canal all sealer remnants were removed with both techniques. In the middle and apical third AH26 was associated with a statistically significant greater quantity of remnants on the root canal walls with both removal techniques ( P < 0.05). Endion, Roth 811 and Roekoseal were associated with approximately the same amount of filling material in the middle third of the root canal ( P > 0.05), whereas in the apical third Endion was associated with significantly more remnants of filling material than the other two sealers with either ProFile or H-files ( P < 0.05). Conclusions None of the methods used for the removal of root fillings was totally effective, especially in the apical third of the root canal. [ABSTRACT FROM AUTHOR]

This study aimed to evaluate the mechanical properties of contemporary heat-treated nickel-titanium (NiTi) rotary instruments used in the single-length technique [ProTaper Next (PTN), HyFlex EDM (EDM), and JIZAI (JZ)]. Bending loads, cyclic fatigue resistance, torque/force values and canal-centering ratios were evaluated for the three instruments and a non-heat-treated experimental NiTi instrument with the same geometry as JZ (nJZ). EDM and JZ exhibited significantly lower bending load and more cycles to failure compared with nJZ and PTN (p<0.05). PTN and JZ exhibited significantly better centering ability than nJZ and EDM (p<0.05). JZ and nJZ generated significantly smaller upward force and maximum torque than PTN and EDM (p<0.05). Under the present experimental condition, JZ exhibited flexibility and cyclic fatigue resistance comparable to EDM, better maintained the canal curvature than the other instruments, and generated smaller torque and screw-in force than PTN and EDM.

This study aimed to evaluate the influence of a post-machining thermal treatment on canal-centering ability and torque/force generation of reciprocating nickel-titanium instruments. Simulated J-shaped resin canals were prepared with reciprocating instruments sharing identical geometric architecture and with/without post-machining thermal treatment (Reciproc Blue/Reciproc, VDW, Munich, Germany). Using an original automated root canal instrumentation and torque/force analyzing device, files were operated in a combination of reciprocation and up-and-down motion, and torque/force values were monitored. Canal-centering ratios were measured after superimposition of pre- and post-instrumentation images. Compared with Reciproc, Reciproc Blue showed a significantly lower canal-centering ratio (i.e., less deviation; p<0.05) at 0-1 mm from the apex and generated a significantly smaller upward maximum vertical force (p<0.05). Under standardized conditions using the automated device, Reciproc Blue showed better canal-centering ability and reduced screw-in forces than Reciproc, indicating that the post-machining thermal treatment confers superior performance to reciprocating nickel-titanium instruments.

Abstract Introduction This study was performed to evaluate how the speed of up-and-down motion affects the canal centering ability and torque/force generation of ProTaper Next rotary instruments (Dentsply Maillefer, Ballaigues, Switzerland). Methods Twenty-one simulated resin canal blocks with a J-shaped canal were prepared with ProTaper Next X1, X2, and X3 instruments using an original automated root canal instrumentation and torque/force analyzing device with up-and-down speed settings of 10, 50, and 100 mm/min (low-, medium-, and high-speed groups, respectively). Pre- and postinstrumentation images were superimposed, and centering ratios were calculated at 0–3 mm from the apex. The maximum vertical force and torque were also recorded. The results were statistically analyzed using 1-way analysis of variance and the Tukey test. Results At 0, 0.5, 1, and 2 mm from the apex, the high-speed group showed the lowest centering ratio (ie, least deviation) followed by the medium-speed and low-speed groups (P <.05). Force values (downward and upward) tended to increase as the up-and-down speed increased; with the X2 and X3 instruments, the high-speed and/or medium-speed groups generated significantly larger values than the low-speed group (P <.05). With all instruments, the high-speed and/or medium-speed groups generated significantly larger clockwise torque than the low-speed group (P <.05). One and 2 X2 instruments fractured in the low- and high-speed groups, respectively. Conclusions The up-and-down speed affected the canal centering ability and stress generation of ProTaper Next instruments. The high-speed group showed the best centering ability but tended to generate larger vertical force and torque than the medium- and low-speed groups. Highlights • The effect of up-and-down speeds on shaping ability and stress was assessed. • Instrumentation was automatically performed by the original device. • Better canal-centering ratio was showed with higher up-and-down speed • With higher up-and-down speed, larger torque and force tended to be generated. [ABSTRACT FROM AUTHOR]