Search

Unmanned aerial vehicle technology is the most advanced and helpful in almost every area of interest in human work. These devices become autonomous and can fulfil a variety of tasks, from simple imaging and obtaining data to search and rescue operations. The most challenging environment for search and rescue operations is the mountainous area. This article is devoted to the theoretical description and simulation tests of a prototype method of landing the light and the medium-weight UAVs used as supplementary devices for SAR (search and rescue) and HEMS (helicopter emergency medical service) in hard-to-reach mountainous terrains. The autonomous flight of a UAV in mountainous terrain has many specifics, and it is usually performed according to predetermined map points (pins) uploaded directly into the control software of the UAV. It is necessary to characterise each point flown on the chosen flight route line in advance and therefore to know its exact geographical coordinates (longitude, latitude and height of the point above the terrain), and the control system of UAV must react to the change in the weather and other conditions in real time. Usually, it is difficult to make this forecast with sufficient time in advance, mainly when UAVs are used as supplementary devices for the needs of HEMS or MRS (mountain rescue service). The most challenging phase is the final approach and landing of the UAV, especially if a loss of GNSS (global navigation satellite system) signal occurs, like in the determined area of the Little Cold Valley in the Slovak High Tatras—which is infamous for the widespread loss of GNSS signals or communication/controlling connection between the UAV and the pilot-operator at the operational station. To solve the loss of guidance, a new method for guiding and controlling the UAV in its final approach and landing in a determined area is tested. An alternative landing navigation system for UAVs in a specific mountainous environment—the authors’ designed frequency Doppler landing system (FDLS)—is briefly described but thoroughly tested with the help of artificial intelligence. An estimation of dynamic stability is used based on the time recording of the current position of the UAV, with the help of a frequency-modulated or amplitude-modulated signal based on the author’s prototype of a precision landing system designed for mountainous terrain. This solution could overcome the problems of GNSS signal loss. The presented research primarily evaluates the success of the simulation flights for the supplementary UAV. The success of navigating the UAV to land in the mountainous environment at an exact landing point using the navigation signals from the FDLS was evaluated at more than 95%.

A helicopter in flight can be considered an unstable dynamic system with many unwanted vibrations originating from multiple sources, such as the operation of the engines and individual components. These vibrations cause the degradation of the structural and functional components of a helicopter, thereby generally reducing the utility and technical efficiency of the aircraft. During the analysis of frequently recurring errors of medium-heavy helicopters, partial damage to antenna elements with vertical polarisation was detected. These damages provided the basis for the presented research, based on which supplementary vibrations caused by unwanted electromagnetic oscillations were revealed. These oscillations were detected in the process of communication between the helicopter crew and the ground ATC (air traffic control) station. This phenomenon’s existence and negative influence were confirmed via measurements and modal analysis, based on which an exact synergy between harmonic frequencies of the helicopter’s normal vibrations was discovered. The obtained results serve as a theoretical and practical basis for the future monitoring of this phenomenon, especially in the process of determining the “health status” of medium-heavy helicopters.

The measurement of the real altitude of aircraft is usually done using an aviation radio altimeter (ALT). A radio altimeter provides crucial information about the instantaneous (radio) altitude of aircraft, helicopter, or unmanned aerial vehicle, to the pilot or another assistance system, such as an autopilot or an anti-collision system. However, this flight altitude measurement is affected by several errors, methodological errors and the operating frequency and modulation parameters instability, or the Doppler shift error. This article is focused on the evaluation of how the Doppler effect error develops during the operation of an ALT and its potential use as an information carrier concerning a possible loss of radio altitude, leading to dangerous situations. This paper briefly explains in a theoretical and practical way how this error develops and how it can affect the process of creation of height impulses. Practical experiments were conducted and evaluated in this research, and a theoretical design of a simple circuit capable of signalization of radio altitude loss presented. As the Doppler shift error was previously recognized solely as a measurement error, it could be used in a new function as a source of supplemental warning information.

The presented article is focused on the evaluation of aviation radio altimeter (ALT) methodological error in order to increase air traffic safety. It briefly explains the background of methodological error at the theoretical level and offers practical conclusions to understand the issue. A radio altimeter provides information on an aircraft or helicopter’s instantaneous (radar) altitude or UAV to the pilot and another assistance system, such as an autopilot or an anticollision system. The height measurement of the most common used ALTs is realized with an accuracy of from ±0.30 m to ±0.75 m. This error rate corresponds to and is caused by the radio altimeter’s methodological error (ΔH). The ALT operating parameters are defined by carrier frequency, modulation frequency, and frequency lift. The methodological error of ALT can be obtained in three ways—calculated on a theoretical level, simulated in a suitable simulation environment, or evaluated in laboratory conditions. The ambiguity of ALT methodological error measurement causes bias in its presentation. This often leads to an incorrect determination of measurement inaccuracy (too optimistic statement of error value). The article’s primary goal is to present a new method for determining the value of the methodological error and its effect on the resulting error of measurement of the radio altitude (radar altitude). It presents a new experimental laboratory method for measuring ΔH and the resulting accuracy of height measurement with a radio altimeter. Thanks to this method, it can be verified that the information obtained by measuring the height above the ground corresponds to the standard specified by the manufacturer.

UAVs, used for professional purposes, often intervene in unfamiliar terrain and challenging conditions. Unlike recreational UAVs, such professional and specialised UAVs are very expensive to develop and operate, and their value is not negligible. Due to the nature of operations in an unknown or dangerous environment, there are also situations with forced interruption and termination of the flight mission or a collision with the environment. Locating a lost vehicle presents a new challenge for UAV operators. The possibilities of today’s localised commercial aircraft in distress (COSPASS/SARSAT systems) are undesirable for selective special-purpose drones. The optimisation of the location in the event of an emergency or catastrophic landing may be justified by a social or other condition, where the user wants to search for the device by a system other than the one experienced for rescuing people, ideally on their reserved frequencies. The article proposes a new approach to solving the problem based on the design of a terrestrial localisation system based on the methods of processing and correlation of the obtained data by the physical principle of the Doppler effect and its own system adaptation. This creates an innovative concept of a targeting system based on the broadcasting of distress (VHF) signal by crashed UAV. This signal is captured and evaluated by the IDVOR system, making it possible to determine the direction in which the searched UAV is placed. In order to determine the difference between standard targeting systems of the UAV, which use information about position (exact coordinates (x,y,z)), the IDVOR system is able to determine direction, independent of other systems in every “enemy” or “inhospitable” territory.

The task of increasing the accuracy and stabilization of the flight of unmanned aerial vehicles (UAV) in the alpine environment is a complex problem. It is related to the evaluation of UAV flight parameters and control conditions for the operator’s place. The purpose of the UAV’s autonomous flight control is to ensure stable control of the UAV’s flight parameters. Flight control systems are affected by various disturbances caused by both internal and external conditions. In general, the number of autonomous control systems corresponds to the number of degrees of freedom, which determines the flight of an autonomous vehicle. An important factor in assessing the quality of such a UAV is its readiness for an autonomous flight together with the level of its safe guidance on the route. The presented article focuses on the analysis of UAV flight control and the quality of prediction and elimination of errors that exist during maneuvers toward the place of a successful UAV landing. The aim of the article is to point out the solvability of the complexities of such a flight procedure with the evaluation of the readiness for the descent phase of the autonomous UAV. The given problem is caused by the social demand for the creation of a way of providing health care in the mountain area of the High Tatras in Slovakia. The existing database of data obtained from the flying vehicles used in Slovakia was compared with the data obtained from the simulated flights, with their subsequent evaluation in the MATLAB software (Version R2021b) environment.

The strict safety requirements of air transport for nonstandard placement of electronic onboard systems require an innovative approach to the experimental verification of the placement of these devices. Particular attention is required to the location of these electronic devices’ antenna systems on the fuselage. A prerequisite for determining the location of the antenna and verifying its radiation is a thorough knowledge of the radio communication transmission of onboard electronic systems in cooperation with terrestrial or satellite systems. From this point of view, this article focuses on an innovative method of verifying the spherical radiation characteristics of the antenna of an onboard rescue system emergency locator transmitter (ELT) to assess its communication link with the Cospas-Sarsat satellite system. The measurement is performed on a small sports two-seater aircraft with an antenna placed in an unusual place in the aircraft’s cabin, between the seats. It was impossible to use a suitable nonreflective attenuation chamber for the measurement, so we present a method and procedure for this type of measurement in the open space of an airport. The achieved results prove the plausibility and reproducibility of the measurement. Furthermore, combining several polar radiation characteristics makes it possible to obtain an idea, even if only a part, of the spatial (spherical) radiation characteristic. This article presents a simple method of measuring the characteristics of aircraft antennas when it is not possible to use a suitable professional nonreflective attenuation chamber for measurements for various reasons. This method can also be used on other larger means of transport or other objects that experience the same problem.