Search

Half-bridge silicon strain gauges are widely used in the fabrication of diaphragm-type high-pressure sensors, but in some applications, they suffer from low output sensitivity because of mounting position constraints. Through a special design and fabrication approach, a new half-bridge silicon strain gauge comprising one arc gauge responding to tangential strain and another linear gauge measuring radial strain was developed using Silicon-on-Glass (SiOG) substrate technology. The tangential gauge consists of grid patterns, such as the reciprocating arc of silicon piezoresistors on a thin glass substrate. When two half-bridges are connected to form a full bridge with arc-shaped gauges that respond to tangential strain, they have the advantage of providing much higher output sensitivity than a conventional half-bridge. Pressure sensors tested under pressure ranging from 0 to 50 bar at five different temperatures indicate a linear output with a typical sensitivity of approximately 16 mV/V/bar, a maximum zero shift of 0.05% FS, and a span shift of 0.03% FS. The higher output level of pressure sensing gauges will provide greater signal strength, thus maintaining a better signal-to-noise ratio than conventional pressure sensors. The offset and span shift curves are quite linear across the operating temperature range, giving the end user the advantage of using very simple algorithms for temperature compensation of offset and span shift.

Various electrocatalysts are extensively examined for their ability to selectively produce desired products by electrochemical CO2 reduction reaction (CO2RR). However, an efficient CO2RR electrocatalyst doesn't ensure an effective co‐catalyst on the semiconductor surface for photoelectrochemical CO2RR. Herein, Bi2S3 nanorods are synthesized and electrochemically reduced to Bi nanoplates that adhere to the substrates for application in the electrochemical and photoelectrochemical CO2RR. Compared with commercial‐Bi, the Bi2S3‐derived Bi (S‐Bi) nanoplates on carbon paper exhibit superior electrocatalytic activity and selectivity for formate (HCOO−) in the electrochemical CO2RR, achieving a Faradaic efficiency exceeding 93%, with minimal H2 production over a wide potential range. This highly selective S‐Bi catalyst is being employed on the Si photocathode to investigate the behavior of electrocatalysts during photoelectrochemical CO2RR. The strong adhesion of the S‐Bi nanoplates to the Si nanowire substrate and their unique catalytic properties afford exceptional activity and selectivity for HCOO− under simulated solar irradiation. The selectivity observed in electrochemical CO2RR using the S‐Bi catalyst correlates with that seen in the photoelectrochemical CO2RR system. Combined pulsed potential methods and theoretical analyses reveal stabilization of the OCHO* intermediate on the S‐Bi catalyst under specific conditions, which is critical for developing efficient catalysts for CO2‐to‐HCOO− conversion. [ABSTRACT FROM AUTHOR]

Currently, silicon-strain-gauge-based diaphragm pressure sensors use four single-gauge chips for high-output sensitivity. However, the four-single-gauge configuration increases the number of glass frit bonds and the number of aluminum wire bonds, reducing the long-term stability, reliability, and yield of the diaphragm pressure sensor. In this study, a new design of general-purpose silicon strain gauges was developed to improve the sensor output voltage while reducing the number of bonds. The new gauges consist grid patterns with a reciprocating arc of silicon piezoresistors on a thin glass backing. The gauges make handling easier in the bonding process due to the use of thin glass for the gauge backing. The pressure sensors were tested under pressure ranging from 0 to 50 bar at five different temperatures, with a linear output with a typical sensitivity of approximately 16 mV/V/bar and an offset shift of –6 mV to 2 mV. The new approach also opens the possibility to extend arc strain gauges to half-bridge and full-bridge configurations to further reduce the number of glass frit and Al wire bonds in the diaphragm pressure sensor.

Monolayer and multilayer molybdenum disulfide (MoS2) materials are semiconductors with direct/indirect bandgaps of 1.2–1.8 eV and are attractive due to their changes in response to electrical, physicochemical, biological, and mechanical factors. Since the desired electrical properties of MoS2 are known, research on its electrical properties has increased, with focus on the deposition and growth of large-area MoS2 and its functionalization. While research on the large-scale production of MoS2 is actively underway, there is a lack of studies on functionalization approaches, which are essential since functional groups can help to dissolve particles or provide adequate reactivity. Strategies for producing films of functionalized MoS2 are rare, and what methods do exist are either complex or inefficient. This work introduces an efficient way to functionalize MoS2. Functional groups are formed on the surface by exposing MoS2 with surface sulfur vacancies generated by plasma treatment to 3-mercaptopropionic acid. This technique can create 1.8 times as many carboxyl groups on the MoS2 surface compared with previously reported strategies. The MoS2-based gas sensor fabricated using the proposed method shows a 2.6 times higher sensitivity and much lower detection limit than the untreated device.

Pristine nanomaterials are normally prepared using finely controlled fabrication processes. Because no imperfect nanostructure remains, they cannot be used directly as electrode substrates of functional devices. This is because perfectly organized nanostructures or nanomaterials commonly require posttreatment to generate intentionally, the kinds of desirable defects inside or on their surfaces that enable effective functionalization. Plasma treatment is an easier, simpler and more widely used way (relative to other methods) to modify a variety of nanomaterials, although plasma-functionalized nano surfaces commonly have a short lifetime. We present herein a dual plasma treatment (DPT) that significantly enhances the degree and lifetime of plasma-induced surface functional groups on single-walled carbon nanotubes (SWCNTs). The DPT process consists of two individually optimized oxygen–plasma treatments. The DPT-modified SWCNT functioned as a sensing material for ammonia gas for more than a month. It also provided more than three times the degree of functionality for amplified signal output than with a single-plasma-treated SWCNT electrode.

We present a cost-effective approach to produce silicon strain gauges that can withstand very high voltage without using any complex package design and without sacrificing any sensor performance. This is achieved by a special silicon strain gauge structure created on an alkali-free glass substrate that has a high breakdown voltage. A half-bridge silicon strain gauge is designed, fabricated, and then tested to measure its output characteristics. The device has a glass layer that is only 25–55 µm thick; it shows it is able to withstand a voltage of over 2000 V while maintaining a high degree of linearity with correlation coefficients higher than 0.9990 and an average sensitivity of 104.13. Due to their unique electrical properties, silicon strain gauges-on-glass chips hold much promise for use in advanced force and pressure sensors.

Microelectronic gas-sensor devices were developed for the detection of carbon monoxide (CO), nitrogen dioxides (NO2), ammonia (NH3) and formaldehyde (HCHO), and their gas-sensing characteristics in six different binary gas systems were examined using pattern-recognition methods. Four nanosized gas-sensing materials for these target gases, i.e., Pd-SnO2 for CO, In2O3 for NOX, Ru-WO3 for NH3, and SnO2-ZnO for HCHO, were synthesized using a sol-gel method, and sensor devices were fabricated using a microsensor platform. Principal component analysis of the experimental data from the microelectromechanical systems gas-sensor arrays under exposure to single gases and their mixtures indicated that identification of each individual gas in the mixture was successful. Additionally, the gas-sensing behavior toward the mixed gas indicated that the traditional adsorption and desorption mechanism of the n-type metal oxide semiconductor (MOS) governs the sensing mechanism of the mixed gas systems.

In this study, the structure–activity relationship of the WO3 photocatalyst and the role of cocatalysts deposited on the WO3 surface were analyzed. Investigation of the phase transformation of WO3 microplates revealed that amorphous WO3 was progressively crystallized into monoclinic WO3 during consecutive thermal treatments. The obtained WO3 microplates were used for the photocatalytic decomposition of organic dyes under simulated solar light irradiation to understand the effect of the crystal structure on the photocatalytic activity. The crystal phase of the WO3 microplates with a monoclinic structure was optimal for the photocatalytic reaction. However, the effects of the crystal phase and the surface area of the WO3 sample were very small, and a deposited metal cocatalyst was essential for achieving photocatalytic activity. The detailed mechanisms and influence of cocatalysts on the WO3 surface were discussed. [ABSTRACT FROM AUTHOR]

The effect of cleaning the surface of single-walled carbon nanotube (SWNT) networks by thermal and the O2 plasma treatments is presented in terms of NH3 gas sensing characteristics. The goal of this work is to determine the relationship between the physicochemical properties of the cleaned surface (including the chemical composition, crystal structure, hydrophilicity, and impurity content) and the sensitivity of the SWNT network films to NH3 gas. The SWNT networks are spray-deposited on pre-patterned Pt electrodes, and are further functionalized by heating on a programmable hot plate or by O2 plasma treatment in a laboratory-prepared plasma chamber. Cyclic voltammetry was employed to semi-quantitatively evaluate each surface state of various plasma-treated SWNT-based electrodes. The results show that O2 plasma treatment can more effectively modify the SWNT network surface than thermal cleaning, and can provide a better conductive network surface due to the larger number of carbonyl/carboxyl groups, enabling a faster electron transfer rate, even though both the thermal cleaning and the O2 plasma cleaning methods can eliminate the organic solvent residues from the network surface. The NH3 sensors based on the O2 plasma-treated SWNT network exhibit higher sensitivity, shorter response time, and better recovery of the initial resistance than those prepared employing the thermally-cleaned SWNT networks.

Electrochemical carbon dioxide reduction is a mild and eco‐friendly approach for CO2 mitigation and producing value‐added products. For selective electrochemical CO2 reduction, single‐crystalline Au particles (octahedron, truncated‐octahedron, and sphere) are synthesized by consecutive growth and chemical etching using a polydiallyldimethylammonium chloride (polyDDA) surfactant, and are surface‐functionalized. Monodisperse, single‐crystalline Au nanoparticles provide an ideal platform for evaluating the Au surface as a CO2reduction catalyst. The polyDDA‐Au cathode affords high catalytic activity for CO production, with >90% Faradaic efficiency over a wide potential range between −0.4 and −1.0 V versus RHE, along with high durability owing to the consecutive interaction between dimethylammonium and chloride on the Au surface. The influence of polyDDA on the Au particles, and the origins of the enhanced selectivity and stability are fully investigated using theoretical studies. Chemically adsorbed polyDDA is consecutively affected the initial adsorption of CO2 and the stability of the *CO2, *COOH, and *CO intermediates during continuous CO2 reduction reaction. The polyDDA functionalization is extended to improving the CO Faradaic efficiency of other metal catalysts such as Ag and Zn, indicating its broad applicability for CO2 reduction. [ABSTRACT FROM AUTHOR]