Search

Numerical flowfields around a scramjet inlet model are simulated and analyzed. The present inlet flowfield is characterized by thick boundary-layer ingestion and strong viscous/inviscid interaction because of a combined effect of high hypersonic freestream Mach and low Reynolds numbers. Shock-induced separation further enlarges regions of viscous flows which occupy most of the inlet flowfield. Results obtained from the computations with the PARC code developed for ideal gas are presented for several 2D cases at various hypersonic Mach numbers ranging from 10 to 25, and two 3D simulations at Mach numbers of 12 and 19 are also discussed. Comparison between computation and experiment is made in terms of pressure distributions at the wall center line. Large discrepancy is observed and may be partially attributed to the lack of real gas and/or 3D effects in the simulation as well as to the uncertainty of the experiment.

The development of a high-efficiency CW YLF laser doped with Er,Tm,Ho: and featuring a strongly focusing resonator that collects a high density of pump power on the active crystal is described. The emission is investigated at 2.06 microns and a tuning range both at liquid-nitrogen (77 K) and at dry-ice (210 K) temperature. The noise characteristics and the long-term power stability of the laser is studied with an eye to employing this source for high-resolution spectroscopy in the 2-micron wavelength region. The detection of several absorption lines of NH3 at low pressure is described. The output power of the laser as a function of the power impinging on the crystal for different transmission of the output mirror is illustrated. The best result obtained is 1.46 W output for 3.2 W of argon pump. The minimum threshold achieved is 3.5 mW with a 1-percent transmission mirror. It is concluded that it is possible to develop a highly efficient Ho:YLF laser featuring low noise and sufficient tunability for high-resolution spectroscopy in the 2-micron region.

A 3-D axisymmetric hypersonic engine inlet was investigated using PARC2D, an ideal gas Computational Fluid Dynamics code. The code was used to predict the results of tests conducted in the Rensselaer Polytechnic Institute Hypersonic Shock Tunnel which measured surface and pitot pressures, and shock positions (through Schlieren photography) at freestream Mach numbers of 10, 13, and 15. A strong viscous/shock interaction was observed in both the experiment and the CFD results, due to the model's parabolic compression ramp. Good agreement was found between the experimental results and the CFD solution both for surface pressures and shock positions. Agreement between pitot pressures was less reliable.

Investigations were conducted into unique methods of converting pulsed laser energy into propulsive thrust across a flat impulse surface under atmospheric conditions. The propulsion experiments were performed with a 1-micron neodymium-glass laser at the Space Plasma Branch of the Naval Research Laboratory. Laser-induced impulse was measured dynamically by ballistic pendulums and statically using piezoelectric pressure transducers on a stationary impulse surface. The principal goal was to explore methods for increasing the impulse coupling performance of airbreathing laser-propulsion engines. A magnetohydrodynamic thrust augmentation effect was discovered when a tesla-level magnetic field was applied perpendicular to the impulse surface. The impulse coupling coefficient performance doubled and continued to improve with increasing laser-pulse energies. The resultant performance of 180 to 200 N-s/MJ was found to be comparable to that of the earliest afterburning turbojets.

Steady-state low-current air arcs in a dual-flow nozzle system are studied experimentally. The cold flow field with no arc is investigated using a 12.7-mm diameter dual-flow nozzle in a steady-flow facility. Mach number and mass flux distributions are determined for various nozzle-pressure ratios and nozzle-gap spacing. It is found that the shock waves in the converging-diverging nozzles result in a decrease in overal resistance by about 15 percent. Also, Schlieren and differential interferometry techniques are used to visualize the density gradients within the arc plasma and thermal mantle. Both optical techniques reveal a laminar arc structure for a reservoir pressure of 1 atm at various current levels. Experimentally determined axial static pressure and cold-flow mass flux rate distributions and a channel-flow model with constant arc temperatre are used to solve the energy integral for the arc radius as a function of axial distance. The arc electric field strength, voltage, resistance, and power are determined with Ohm's law and the total heat transfer is related to arc power.

The objective of this experimental study was to investigate the influence of horseshoe vortex on the heat transfer on a flat plate near the base of a protruding cylinder. The partial shock reflection technique was used to produce the flow Mach number of 0.14 which simulated the mean inlet flow Mach number for the first stage vanes of the turbine after combustor. Fast response thin-film platinum heat gages were used to measure the heat transfer flux for radial distances of 0.75, 0.875, 1.0, 1.125 cylinder diameter. For a low Reynolds number of 20,000, r/D = 0.75, and angular location from the stagnation point = 60 deg, the maximum increase in the heat transfer rate with the cylinder was observed to be approximately 460 percent greater than without the cylinder. On the other hand, the increase in the heat flux for a high Reynolds number of 300,000 was approximately 70 percent greater. For the heat gages located along 30 deg and 60 deg angular locations from the stagnation point, the strong effect of the horseshoe vortex was observed in the junction region. The increase in the heat transfer rate depended on the type of boundary layer and on the boundary layer thickness ahead of the cylinder.

The heat transfer rate in the stagnation region of the junction of a circular cylinder perpendicular to a flat plate was measured for a range of Reynolds numbers varying from 3.0 x 10 to the 4th to 7.0 x 10 to the 5th and a flow Mach number of 0.14. The measurements were performed in a shock-tube facility using a reflected shockwave technique and thin-film platinum heat gages. The heat flux was measured for both the plate and the circular cylinder. A substantial increase in the heat transfer rate in the junction region was observed. The influence of the cylinder over the flat plate extended beyond 3/4 cylinder diameter for low Reynolds numbers. For high Reynolds numbers the maximum increase in the heat transfer rate was observed to be approximately 100 percent, but for very low Reynolds numbers a maximum increase in the heat flux to the plate by a factor of 5 was observed. The variations in the heat transfer rate to the stagnation point of the cylinder was very small.

The relaminarization of the boundary layer over a flat plate in the shock tube was investigated by using the partially reflected shock wave technique. The flow Mach number was approximately 0.14, which corresponds to the inleft flow Mach number for the first row of vanes in a gas turbine. The thin film platinum heat gauges were used to measure the heat transfer rate and the Stanton number was calculated from the oscilloscope voltage traces. The Reynolds number was varied by changing the operation pressure of the shock tube and the values varied from 2.3 x 10 to the 4th to 5.3 x 10 to the 5th. For a Reynolds number range of 7 x 10 to the 4th to 3.5 x 10 to the 5th, the relaminarization of the boundary layer was observed. This phenomenon is due to the decay of the turbulence level in the flow as the reflected shock wave moves upstream from the flat plate. As the Reynolds number increased, the relaminarization was delayed and the delay was related to the turbulence generated by the reflected shock wave.

One of the problems for the hypersonic flights is the lack of accurate methods for predicting the boundary layer parameters at high Mach numbers and temperatures. At high Mach numbers and temperatures, the real gas effects should be included in calculations of the compressible laminar and turbulent boundary layers. By introducing the Mangler-Levy-Lees transformation, the compressible laminar boundary layer equations were transformed into two ordinary differential equations. To solve these ordinary differential equations for the flow over a flat plate, the Runge-Kutta method of order 5 and 6 was used with a secant method of solving the simultaneous nonlinear equations for the boundary layer conditions. Instead of using the perfect gas assumptions, the properties of air in the temperature range of 100 to 2500 K at M(e) = 8 were used for the calculations. The calculations were carried out for free flight conditions. The real gas effects were significant for the conditions of high freestream Mach numbers, and the boundary layer parameters from the real gas solutions were quite different from the existing formulas and solutions.

In studying transition behavior a shock tube and tunnel were used to produce high temperatures, and thin-film platinum heat gauges were used to measure local heat flux as well as to detect the transition of the laminar boundary layer over a flat plate and a cone. Initial investigations were conducted in the hypersonic shock tunnel to obtain high-temperature information for the development of an ICBM nose cone. Shock Mach numbers as large as 50 with a temperature of 15,000 K after the incident wave were produced in the driven tube. Shock tubes are used to investigate the heat transfer over various surfaces to 2500 K for the development of future gas turbines.

Airfoils operating in the transonic region are subject to large increases in drag due to shock wave/boundary layer interactions. The concept of passive shock wave/boundary layer control seeks drag reduction by placing a thin cavity with a porous top surface at the airfoil chordwise position where a shock wave would normally occur. The higher pressure behind the shock wave circulates flow through the cavity to the lower pressure ahead of the shock wave. The effects from this circulation prevent boundary layer separation and reduce entropy increases through the shock wave. In this investigation this concept is studied at a freestream Mach number range of .75 and .90. The Mach number distributions over the model, the wake impact pressure surveys used to determine profile drag and schlieren photographs for 2.8 percent porosity and solid airfoil cases are presented and compared. Results indicate that the profile drag coefficient can be reduced by as much as 40 percent through the use of this passive drag control system.

External heat-transfer rates were measured on a flat plate in the junction region of a circular cylinder mounted normal to the plate at a location 90 deg from the stagnation point. This configuration simulates the junction of the shroud with gas-turbine vanes. Heat-transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.14 with gas temperatures of approximately 750 deg R over a flat plate at room temperature. The measurements were made in air for a unit Reynolds number, Re/cm, range of 11,000 to 58,000. Heat-transfer measurements were conducted in the 70-ft long, 4-in. diameter shock tube. A shock-wave reflection technique was used to produce a flow Mach number of 0.14. Thin-film platinum heat gages were mounted on the flat plate and along the line of the stagnation point of the cylinder to measure the local heat flux in the junction region. The experimental heat-transfer data were correlated with the laminar and turbulent boundary-layer theories for the flat plate. With the cylinder the heat fluxes on the flat plate were greatly increased in the junction region compared to the heat flux for the plate alone.

The passive shock wave/boundary layer control for reducing the drag of 14%-thick supercritical airfoil was investigated in the 3 in. x 15.4 in. RPI Transonic Wind Tunnel with and without the top wall insert at transonic Mach numbers. Top wall insert was installed to increase the flow Mach number to 0.90 with the model mounted on the test section bottom wall. Various porous surfaces with a cavity underneath were positioned on the area of the airfoil where the shock wave occurs. The higher pressure behind the shock wave circulates flow through the cavity to the lower pressure ahead of the shock wave. The effects from this circulation prevent boundary layer separation and enthropy increase hrough the shock wave. The static pressure distributions over the airfoil, the wake impact pressure survey for determining the profile drag and the Schlieren photographs for porous surfaces are presented and compared with the results for solid surface airfoil. With a 2.8% uniform porosity the normal shock wave for the solid surface was changed to a lambda shock wave, and the wake impact pressure data indicate a drag coefficient reduction as much as 45% lower than for the solid surface airfoil at high transonic Mach numbers.

Heat transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.12 with gas temperatures of 425 K and 1000 K over a flat plate at room temperature. The measurements were made in air for a Reynolds number range of 600 to 6 million. The heat transfer measurements were conducted in a 70-ft long, 4 in. diameter shock tube. Reflecting wedges were used to reflect the incident shock wave to produce a flow Mach number of 0.12 behind the reflected shock wave. Thin film platinum heat gages were mounted on the plate surface to measure the local heat flux. The laminar results for gas temperatures of 425 K to 1000 K agree well with theory. The turbulent results are also close to incompressible theory, with the 1000 K flow case being slightly higher. The transition results lie between the laminar and turbulent predictions.

Heat transfer measurements were determined for a flat plate with and without pressure gradient for various free stream temperatures, wall temperature ratios, and Reynolds numbers for an inlet flow Mach number of 0.45, which is a representative inlet Mach number for gas turbine rotor blades. A shock tube generated the high temperature and pressure air flow, and a variable geometry test section was used to produce inlet flow Mach number of 0.45 and accelerate the flow over the plate to sonic velocity. Thin-film platinum heat gages recorded the local heat flux for laminar, transition, and turbulent boundary layers. The free stream temperatures varied from 611 R (339 K) to 3840 R (2133 K) for a T(w)/T(r,g) temperature ratio of 0.87 to 0.14. The Reynolds number over the heat gages varied from 3000 to 690,000. The experimental heat transfer data were correlated with laminar and turbulent boundary layer theories for the range of temperatures and Reynolds numbers and the transition phenomenon was examined.

An investigation of the passive shock wave/boundary layer control for reducing the drag of 14 percent-thick supercritical airfoil was conducted in the 3 in. x 15.4 in. RPI Transonic Wind Tunnel at transonic Mach numbers. Various porous surfaces with a cavity beneath it was positioned on the area of the airfoil, mounted on the test section bottom wall, where the shock wave occurs. The static pressure distributions over the airfoil, the wake impact pressure survey for determining the profile drag and the Schlieren photographs for porous surfaces are presented and compared with the results for solid surface airfoil. With a uniform porosity surface the normal shock wave for solid surface was changed to a lambda shock wave, and the wake impact pressure data indicated an appreciable drag reduction at transonic Mach numbers. For a free stream Mach number of 0.81 the profile drag coefficient for the airfoil top surface with uniform porosity was 46 percent lower than for the solid surface airfoil.

Low and high pressure shock tubes were designed and constructed for the purpose of obtaining heat transfer data over a temperature range of 390 to 2500 K, pressures of 0.3 to 42 atm, and Mach numbers of 0.15 to 1.5 with and without pressure gradient. A square test section with adjustable top and bottom walls was constructed to produce the favorable and adverse pressure gradient over the flat plate with heat gages. A water cooled gas turbine nozzle cascade which is attached to the high pressure shock tube was obtained to measuse the heat flux over pressure and suction surfaces. Thin-film platinum heat gages with a response time of a few microseconds were developed and used to measure the heat flux for laminar, transition, and turbulent boundary layers. The laminar boundary heat flux on the shock tube wall agreed with Mirel's flat plate theory. Stagnation point heat transfer for circular cylinders at low temperature compared with the theoretical prediction, but for a gas temperature of 922 K the heat fluxes were higher than the predicted values. Preliminary flat plate heat transfer data were measured for laminar, transition, and turbulent boundary layers with and without pressure gradients for free-stream temperatures of 350 to 2575 K and flow Mach numbers of 0.11 to 1.9. The experimental heat flux data were correlated with the laminar and turbulent theories and the agreement was good at low temperatures which was not the case for higher temperatures.

The optimization of passive shock wave/boundary layer control for supercritical airfoil drag reduction was investigated in a 3 in. x 15.4 in. Transonic Blowdown Wind Tunnel. A 14% thick supercritical airfoil was tested with 0%, 1.42% and 2.8% porosities at Mach numbers of .70 to .83. The 1.42% case incorporated a linear increase in porosity with the flow direction while the 2.8% case was uniform porosity. The static pressure distributions over the airfoil, the wake impact pressure data for determining the profile drag, and the Schlieren photographs for porous surface airfoils are presented and compared with the results for solid-surface airfoils. While the results show that linear 1.42% porosity actually led to a slight increase in drag it was found that the uniform 2.8% porosity can lead to a drag reduction of 46% at M = .81.

The deblocking process in a circuit breaker nozzle is similar to the flow starting process in a shock tunnel, and the computer uses this analogy to solve for the deblocking process by utilizing a diaphragm at the throat of a nozzle. At time equal to zero the diaphragm is broken and the throat area increases with time. It is a rarity to have the area as a function of both time and distance. Experimental data obtained from the RPI calibration shock tunnel are utilized to verify some of the calculated results with the area being a function of distance and the agreement is found to be good. The circuit breaker designer can utilize the computer simulation to estimate the deblocking time, an important parameter in the design of circuit breakers.

An investigation of the passive shock wave/boundary layer interaction control for reducing the drag in 12 percent thick circular arc and 14 percent thick supercritical airfoils was conducted in a 3 in. x 15.4 in. transonic wind tunnel at transonic Mach numbers. A porous surface with a cavity beneath it was positioned on the area of the airfoils, mounted on the test section bottom wall, where the shock wave occurs. The static pressure distributions over the airfoil, the wake impact pressure data for determining the profile drag, and the Schlieren photographs for porous surface airfoils are presented and compared with the results for solid surface airfoils. With the porous surface the normal shock wave for solid surface was changed to a lambda shock wave system, and the wake impact pressure data indicated an appreciable drag reduction for both airfoils with the porous surface at transonic speeds while causing little or no loss of lift. The effect of porosity and cavity size is investigated and off-design performance is discussed.

The passive drag control concept, consisting of a porous surface with a cavity beneath it, was investigated with a 12-percent-thick circular arc and a 14-percent-thick supercritical airfoil mounted on the test section bottom wall. The porous surface was positioned in the shock wave/boundary layer interaction region. The flow circulating through the porous surface, from the downstream to the upstream of the terminating shock wave location, produced a lambda shock wave system and a pressure decrease in the downstream region minimizing the flow separation. The wake impact pressure data show an appreciably drag reduction with the porous surface at transonic speeds. To determine the optimum size of porosity and cavity, tunnel tests were conducted with different airfoil porosities, cavities and flow Mach numbers. A higher drag reduction was obtained by the 2.5 percent porosity and the 1/4-inch deep cavity.

Surface heat transfer rates were measured on a sharp flat plate at zero angle of attack with helium over a Mach number range of 22.8 to 86.8 in a hypersonic shock tunnel. The density and leading edge Knudsen numbers were varied to span the continuum to near free molecule regimes. The strong interaction parameter varied from 11 to 16,000 with leading edge Knudsen numbers from 0.56 to 17.1, respectively. For high unit Reynolds number the rate of change of the heat transfer coefficient with the strong interaction parameter agreed well with the strong interaction theory of Li and Nagamatsu (1953, 1955).

Local heat transfer rates were measured on a flat steel plate (10 in. wide and 16 in. long) with sharp and blunt leading edges (0.001 and 0.010 in.) in the transition from the strong interaction boundary layer regime with no slip at the surface to the free molecule regime. The tests were conducted in a combustion driven hypersonic shock tunnel, with the nominal free stream Mach numbers of 19.2 and 25.4, and a reflected stagnation temperature of approximately 2340 R. The twelve heat transfer gages were made of platinum sputtered on a Pyrex backing to a thickness of approximately 350 A, insulated by a silicone dioxide film. For both Mach numbers the heat transfer data agreed reasonably well with the strong interaction prediction of Li and Nagamatsu (1953, 1955) for unit Reynolds numbers greater than approximately 100,000 and leading edge Knudsen numbers less than approximately 4. At lower density conditions the rarefied flow effects began to dominate the flow phenomena near the leading edge region of the sharp flat plate. A systematic reduction in the heat transfer rate close to the leading edge was observed for both Mach number tests as the leading edge density was reduced and the mean free path was increased.

The cold air flow field for a 1/27 cm orifice nozzle was determined for subsonic flow velocities. In addition, d.c. arc voltage, current, and diameter measurements were made for a range of velocities and arc gaps. Average voltage gradients increased rapidly as an arc extinguishing velocity was approached. Measured values of current and diameter were used as an input for relaxation solution of an energy balance equation to compute radial temperature profiles. Calculated arc voltage gradients compare favorably with measured average voltage gradients.

Mean and fluctuating velocity contours were determined for a convergent nozzle from surveys with impact pressure and piezoelectric pressure gauge probes, at Mach numbers of 0.6 to 1.4. For supersonic Mach numbers of 1.2 and 1.4, the length of the supersonic region increased as the square of the Mach number, and the peak pressure fluctuations occurred close to the sonic velocity contour. For subsonic Mach numbers of 0.6 to 1.0, the peak pressure fluctuations occurred in a toroidal region located approximately 4 to 6 diameters from the nozzle. The normalized sound power spectra for subsonic Mach numbers were similar, and for supersonic Mach numbers the power spectra shifted to the higher frequencies.

To study the similarities and differences between subsonic and supersonic jets, velocity and impact pressure fluctuations were determined along the axis over a jet Mach number range of 0.6 to 1.4 for a 2 in. diameter convergent nozzle and for a one inch diameter jet flow. Static pressure distribution fluctuations due to shear and turbulence in the jet flow for subsonic and supersonic jets were related to acoustic radiation to the far field. Also determined were flow and acoustic characteristics of a single shroud, and multiple shroud tube and shroud suppressors for supersonic and subsonic exhaust velocities. A compressor consisting of 191 tubes and 191 shrouds decreased the primary Mach number drastically for both jet Mach numbers of 1.4 and 0.7; rms impact and static pressure fluctuations on the axis were also reduced from values existing for an equivalent area single nozzle.

Surface heat transfer rates were measured on a sharp flat plate at zero angle of attack in a hypersonic shock tunnel. The density and leading edge Knudsen number were varied to span the continuum to near free molecule regimes. The strong interaction parameter varied from 11 to 16,000 with Knudsen numbers from 0.56 to 17.1 respectively. Local heat transfer rates in the corner flow region produced by the intersection of two perpendicular flat plates with sharp leading edges were determined for various flow densities. The strength of the shock wave from the vertical plate was varied by adjusting the angle of attack from 0 to 5 deg. The unit Reynolds number varied from 1,000 to 17,200 and the Knudsen numbers from 1.6 to 27. The strong interaction parameter varied from 14 to 500.

Acoustic and flow characteristics of subsonic and supersonic jets from convergent nozzles