Search

Made available in DSpace on 2021-06-25T11:06:19Z (GMT). No. of bitstreams: 0 Previous issue date: 2020-11-01 $\beta $ -Ga2O3 is one of the promising semiconductor materials that has been widely used in power electronics and ultraviolet (UV) detectors due to its wide bandgap and high sensitivity to UV light. Specifically, for the UV detection application, it has been reported that the photocurrent was in the scale of microamps ( $\mu \text{A}$ ), which normally requires sophisticated signal processing units. In this work, a novel approach based upon coupling of two Schottky diodes is reported, leads to a substantial increase in photocurrent (186 times) when benchmarked against a conventional planar UV photodiode. The detectivity and responsivity of the new device have also been significantly increased; the rectification ratio of this device was measured to be $1.7\times 10^{7}$ with ultralow dark current, when measured in the reverse bias. The results confirm that the approach of coupling two Schottky diodes has enormous potential for improving the optical performance of deep UV sensors. Departamento de Fisica UNESP - Sao Paulo State University Multidisciplinary Nanotechnology Centre College of Engineering Swansea University School of Electronic Engineering Bangor University Departamento de Fisica UNESP - Sao Paulo State University

Graphene exhibits both high electrical conductivity and large elastic modulus, which makes it an ideal material candidate for many electronic devices. At present not much work has been conducted on using graphene to construct thermoelectric devices, particularly due to its high thermal conductivity and lack of bulk fabrication. Films of graphene-based materials, however, and their nanocomposites have been shown to be promising candidates for thermoelectric energy generation. Exploring methods to enhance the thermoelectric performance of graphene and produce bulk samples can significantly widen its application in thermoelectrics. Realization of bulk organic materials in the thermoelectric community is highly desired to develop cheap, Earth-abundant, light, and nontoxic thermoelectric generators. In this context, this work reports a new approach using pressed pellets bars of few-layered graphene (FLG) nanoflakes employed in thermoelectric generators (TEGs). First, FLG nanoflakes were produced by a novel dry physical grinding technique followed by graphene nanoflake liberation using plasma treatment. The resultant material is highly pure with very low defects, possessing 3 to 5-layer stacks as proved by Raman spectroscopy, X-ray diffraction measurement, and scanning electron microscopy. The thermal and electronic properties confirm the anisotropy of the material and hence the varied performance characteristics parallel to and perpendicular to the pressing direction of the pellets. The full thermoelectric properties were characterized both parallel and perpendicular to the pressing direction, and the proof-of-concept thermoelectric generators were fabricated with variable amounts of legs.

Nasoseptal cartilage has been assumed to be isotropic, unlike the well-defined zonal organization of articular cartilage attributed to postnatal biomechanical loading. We know from clinical experience that malrotation of surgical nasoseptal cartilage grafts can lead to increased graft absorption. Other studies have also suggested directionally dependent compressive stiffness suggesting anisotropy, but morphological investigations are lacking. This study characterizes immature and mature native bovine nasoseptal cartilage using a combination of immunohistochemistry, biomechanical testing and structural imaging. Our findings indicate that there is extensive postnatal synthesis and reorganization of the extracellular matrix in bovine nasoseptal cartilage, independent of joint loading forces responsible for articular cartilage anisotropy. Immature nasoseptal cartilage is more cellular and homogenous compared to the zonal organization of cells and extracellular matrix of mature cartilage. Mature samples also exhibited greater glycosaminoglycan content and type II collagen fibre alignment compared to immature cartilage and this correlates with greater compressive stiffness. Engineered neocartilage often consists of immature, isotropic, homogenous tissue that is unable to meet the functional and mechanical demands when implanted into the native environment. This study demonstrates the importance of anisotropy on biomechanical tissue strength to guide future cartilage tissue engineering strategies for surgical reconstruction.

As practical interest in the flexible or wearable thermoelectric generators (TEGs) has increased, the demand for the high-performance TEGs based on ecofriendly, mechanically resilient, and economically viable TEGs as alternatives to the brittle inorganic materials is growing. Organic or hybrid thermoelectric (TE) materials have been employed in flexible TEGs; however, their fabrication is normally carried out using wet processing such as spin-coating or screen printing. These techniques require materials dissolved or dispersed in solvents; thus, they limit the substrate choice. Herein, we have rationally designed solvent-free, all carbon-based TEGs dry-drawn on a regular office paper using few-layered graphene (FLG). This technique showed very good TE parameters, yielding a power factor of 97 μW m–1 K–2 at low temperatures. The p-type only device exhibited an output power of up to ∼19.48 nW. As a proof of concept, all carbon-based p-n TEGs were created on paper with the addition of HB pencil traces. The HB pencil exhibited low Seebeck coefficients (−7 μV K–1), and the traces were highly resistive compared to FLG traces, which resulted in significantly lower output power compared to the p-type only TEG. The demonstration of all carbon-based TEGs drawn on paper highlights the potential for future low-cost, flexible, and almost instantaneously created TEGs for low-power applications.

β-Ga 2 O 3 is a promising semiconductor for electronic devices. In the present work we have demonstrated a novel method for manufacturing a β-Ga 2 O 3 Schottky diode, in which the same electrode material is used for both contacts. The device is tested it for its applicability in deep UV sensing. Devices were manufactured directly onto β-Ga 2 O 3 (010) wafer material. From the perspective of diode performance, a high rectification ratio of 1.5x107 and high forward current of 17.58 mA/cm2 at −5 V bias was obtained. A responsivity of 12.5 mA/W was recorded when irradiated with light possessing a wavelength of 254 nm. Importantly, detailed analysis is conducted in order to evaluate the performance of the Schottky diode using Cheung’s and Norde’s methods allowing for accurate calculation of the Schottky barrier height in this device.

INTRODUCTION Thrombosis is a severe and frequent complication of heparin-induced thrombocytopenia (HIT). However, there is currently no knowledge of the effects of HIT-like antibodies on the resulting microstructure of the formed clot, despite such information being linked to thrombotic events. We evaluate the effect of the addition of pathogenic HIT-like antibodies to blood on the resulting microstructure of the formed clot. MATERIALS AND METHODS Pathogenic HIT-like antibodies (KKO) and control antibodies (RTO) were added to samples of whole blood containing Unfractionated Heparin and Platelet Factor 4. The formed clot microstructure was investigated by rheological measurements (fractal dimension; df) and scanning electron microscopy (SEM), and platelet activation was measured by flow cytometry. RESULTS AND CONCLUSIONS Our results revealed striking effects of KKO on clot microstructure. A significant difference in df was found between samples containing KKO (df = 1.80) versus RTO (df = 1.74; p

In this study, a comparative analysis of the instabilities and degradation routes of organic solar cell (OSCs) employing the three benchmarked donor polymers namely poly(3-hexylthiophene) (P3HT), poly[N-900- hepta-decanyl-2,7-carbazole-alt-5,5-(40,70-di-2-thienyl-20,10,30-benzothiadiazole)] (PCDTBT) and Poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2- b:4,5-b']dithiophene-2,6-diyl][3-fluoro-2-[(2 ethylhexyl)carbonyl] thieno[3,4-b]thiophenediyl]] (PTB7) along with [6,6]-phenylC71 butyric acid methyl-ester (PC71BM) acceptor have been conducted using the extracted photovoltaic parameters in conjunction with the X-ray photoelectron spectroscopy (XPS), optical and morphological analysis. During the 14 days air stability test, the power conversion efficiency (PCE) decreased by 78.85%, 65.83% and 83.36% for P3HT:PC71BM, PCDTBT:PC71BM and PTB7:PC71BM based devices, respectively. However, the degradation study of the bulk heterojunction (BHJ) films was prolonged to 28 days in order to further elucidate the degradation factors affecting the device performance. XPS, optical and morphological studies enabled detailed information on the device degradation mechanisms and confirmed the oxidation of photoactive layer after ageing, morphological deterioration and fall in absorbance, particularly, the PTB7:PC71BM blend that showed the rapid degradation among all three. The results obtained in the current study advance the understanding of the stability/degradation mechanisms pertaining to the three most commonly used BHJ materials and hence, will help to improve the OSCs for longer lifetime.

In this work, we have shown that betagallium oxide (Ga2O3) thin films of differing thickness could be obtained by physical vapor deposition method, employing proper annealing conditions. These enable us to compare the variation of optical properties like transparency, band gap in these phases. Apart from these, our analysis of transmittance spectra of beta-Ga2O3 indicated the reduction of structural disorders (amorphous to crystalline) with increase in annealing temperature. The calculated band gap based on Density Functional Theory (DFT) for bulk beta-Ga2O3 thin films ~ 4.9 eV (direct) at room temperature is in excellent agreement with our experimentally measured values. This work will serve as design guidance for the new Ga2O3 based thin film electronics.

Background: One of the main challenges for extrusion 3D bioprinting is the identification of non-synthetic bioinks with suitable rheological properties and biocompatibility. Our aim was to optimise and compare the printability of crystal, fibril and blend formulations of novel pulp derived nanocellulose bioinks and assess biocompatibility with human nasoseptal chondrocytes for cartilage bioprinting. Methods: The printability of crystalline, fibrillated and blend formulations of nanocellulose was determined by assessing resolution (grid-line assay), post-printing shape fidelity and rheology (elasticity, viscosity and shear thinning characteristics) and compared these to pure alginate bioinks. The optimised nanocellulose-alginate bioink was bioprinted with human nasoseptal chondrocytes to determine cytotoxicity, metabolic activity and bioprinted construct topography. Results: All nanocellulose-alginate bioink combinations demonstrated a high degree of shear thinning with reversible stress softening behaviour which contributed to post-printing shape fidelity. The unique blend of crystal and fibril nanocellulose bioink exhibited nano- as well as micro-roughness for cellular survival and differentiation, as well as maintaining the most stable construct volume in culture. Human nasoseptal chondrocytes demonstrated high metabolic activity post printing and adopted a rounded chondrogenic phenotype after prolonged culture. Conclusions: This study highlights the favourable rheological, swelling and biocompatibility properties of nanocellulose-alginate bioinks for extrusion-based bioprinting.

Nasoseptal cartilage has been assumed to be isotropic, unlike the well-defined zonal organization of articular cartilage attributed to postnatal biomechanical loading. We know from clinical experience that malrotation of surgical nasoseptal cartilage grafts can lead to increased graft absorption. Other studies have also suggested directionally dependent compressive stiffness suggesting anisotropy, but morphological investigations are lacking. This study characterizes immature and mature native bovine nasoseptal cartilage using a combination of immunohistochemistry, biomechanical testing and structural imaging. Our findings indicate that there is extensive postnatal synthesis and reorganization of the extracellular matrix in bovine nasoseptal cartilage, independent of joint loading forces responsible for articular cartilage anisotropy. Immature nasoseptal cartilage is more cellular and homogenous compared to the zonal organization of cells and extracellular matrix of mature cartilage. Mature samples also exhibited greater glycosaminoglycan content and type II collagen fibre alignment compared to immature cartilage and this correlates with greater compressive stiffness. Engineered neocartilage often consists of immature, isotropic, homogenous tissue that is unable to meet the functional and mechanical demands when implanted into the native environment. This study demonstrates the importance of anisotropy on biomechanical tissue strength to guide future cartilage tissue engineering strategies for surgical reconstruction.

Nanocellulose is a natural biopolymer derived from cellulose. Combined with sodium alginate, it is used to 3D print hydrogels for articular and nasal cartilage engineering and shows good integration, promising cartilage regeneration and mechanical stability over 60 days of implantation in mice. Yet, little is known about their structural and mechanical properties, particularly the impact of crosslinking and sterilisation methods. This study investigates the impact of different calcium chloride crosslinker concentrations and sterilization methods on the structural and mechanical properties of nanocellulose-based hydrogels containing plant-derived cellulose nanofibrils, cellulose nanocrystals or a blend of the two. Crosslinking significantly alters the overall network distribution, surface morphology, pore size and porosity of the hydrogels. Sterilisation has a striking effect on pore size and affects swelling depending on the sterilisation method. The effect of crosslinker and sterilisation on the overall properties of the hydrogels was reliant on the form of nanocellulose that comprised them.

Background The rheological properties of sputum may influence lung function and become modified in disease. Objective This study aimed to correlate the viscoelastic properties of sputum with clinical data on the severity of disease in patients with chronic obstructive pulmonary disease (COPD). Methods Sputum samples from COPD patients were investigated using rheology, simple mathematical modelling and Scanning Electron Microscopy (SEM). The samples were all collected from patients within two days of their admission to Prince Philip Hospital due to an exacerbation of their COPD. Oscillatory and creep rheological techniques were used to measure changes in viscoelastic properties at different frequencies over time. Results COPD sputum was observed to behave as a viscoelastic solid at all frequencies studied. Comparing the rheology of exacerbated COPD sputum with healthy sputum (not diagnosed with a respiratory disease) revealed significant differences in response to oscillatory shear and creep-recovery experiments, which highlights the potential clinical benefits of better understanding sputum viscoelasticity. A common power law model G(t)=G0(tτ0)-m was successfully fitted to experimental rheology data over the range of frequencies studied. Conclusions A comparison between clinical data and the power law index m obtained from rheology, suggested that an important possible future application of this parameter is as a potential biomarker for COPD severity.

Incipient clot formation in whole blood and fibrin gels was studied by the rheometric techniques of controlled stress parallel superposition (CSPS) and small amplitude oscillatory shear (SAOS). The effects of unidirectional shear stress on incipient clot microstructure, formation kinetics and elasticity are reported in terms of the fractal dimension (df) of the fibrin network, the gel network formation time (TGP) and the shear elastic modulus, respectively. The results of this first haemorheological application of CSPS reveal the marked sensitivity of incipient clot microstructure to physiologically relevant levels of shear stress, these being an order of magnitude lower than have previously been studied by SAOS. CSPS tests revealed that exposure of forming clots to increasing levels of shear stress produces a corresponding elevation in df, consistent with the formation of tighter, more compact clot microstructures under unidirectional flow. A corresponding increase in shear elasticity was recorded. The scaling relationship established between shear elasticity and df for fibrin clots and whole blood confirms the fibrin network as the dominant microstructural component of the incipient clot in terms of its response to imposed stress. Supplementary studies of fibrin clot formation by rheometry and microscopy revealed the substantial additional network mass required to increase df and provide evidence to support the hypothesis that microstructural changes in blood clotted under unidirectional shear may be attributed to flow enhanced thrombin generation and activation. CSPS also identified a threshold value of unidirectional shear stress above which no incipient clot formation could be detected. CSPS was shown to be a valuable haemorheological tool for the study of the effects of physiological and pathological levels of shear on clot properties.

Infection is a clinically relevant adverse event in patients with ventricular assist device (VAD) support. The risk of infection could be linked to a reduced immune response resulting from damage to leukocytes during VAD support. The purpose of this study was to develop an understanding of leukocyte responses during the in vitro testing of VADs by analyzing the changes to their morphology and biochemistry. The VentrAssist implantable rotary blood pump (IRBP) and RotaFlow centrifugal pump (CP) were tested in vitro under constant hemodynamic conditions. Automated hematology analysis of samples collected regularly over 25-h tests was undertaken. A new flow cytometric assay was employed to measure biochemical alteration, necrosis (7-AAD) and morphological alteration (CD45 expression) of the circulating leukocytes during the pumping process. The results of hematology analysis show the total leukocyte number and subset counts decreased over the period of in vitro tests dependent on different blood pumps. The percentage of leukocytes damaged during 6-h tests was 40.8 ± 5.7% for the VentrAssist IRBP, 17.6 ± 5.4% for the RotaFlow CP, and 2.7 ± 1.8% for the static control (all n=5). Flow cytometric monitoring of CD45 expression and forward/side scatter characteristics revealed leukocytes that were fragmented into smaller pieces (microparticles). Scanning electron microscopy and imaging flow cytometry were used to confirm this. Device developers could use these robust cellular assays to gain a better understanding of leukocyte-specific VAD performance.

Infection is a clinically relevant adverse event in patients with ventricular assist device (VAD) support. The risk of infection could be linked to a reduced immune response resulting from damage to leukocytes during VAD support. The purpose of this study was to develop an under- standing of leukocyte responses during the in vitro testing of VADs by analyzing the changes to their morphology and biochemistry. The VentrAssist implantable rotary blood pump (IRBP) and RotaFlow centrifugal pump (CP) were tested in vitro under constant hemodynamic conditions. Automated hematology analysis of samples collected regu- larly over 25-h tests was undertaken.A new flow cytometric assay was employed to measure biochemical alteration, necrosis (7-AAD) and morphological alteration (CD45 expression) of the circulating leukocytes during the pumping process. The results of hematology analysis show the total leukocyte number and subset counts decreased over the period of in vitro tests dependent on different blood pumps. The percentage of leukocytes damaged during 6-h tests was 40.8 ± 5.7% for the VentrAssist IRBP, 17.6 ± 5.4% for the RotaFlow CP, and 2.7 ± 1.8% for the static control (all n = 5). Flow cytometric monitoring of CD45 expression and forward/side scatter characteristics revealed leukocytes that were fragmented into smaller pieces (microparticles). Scanning electron microscopy and imaging flow cytometry were used to confirm this. Device developers could use these robust cellular assays to gain a better understanding of leukocyte-specific VAD per- formance. Key Words: Leukocyte damage—Ventricular assist devices—Flow cytometric assay—Leukocyte-derived microparticles.

This study investigates the potential use of rheometry to provide a structural biomarker for acute critical illness. Previous studies have reported an association of altered fibrin clot network architecture with several diseases including sepsis, bleeding or acute thromboembolic disease [1]. We investigate our biomarker by examining the relationship between thrombin generation and clot architecture in an in vitro model.

We report a study of the microstructural templating role of incipient fibrin–thrombin gels by analysis of rheological and confocal microscope measurements. Fractal analysis based on the spectral dimension is used, for the first time, to characterise fibrin gel microstructure in terms of the internal connectivity of gel networks. A significant correlation is found between the fractal characteristics of the incipient gel network and its eventual mature form, confirming that incipient gel microstructure templates ensuing gel development. We report an analytical basis for the study of this templating effect which reveals two different regimes of microstructural development. The first involves low thrombin concentration, in which increasing concentration decreases the gel formation time and alters the fractal characteristics of both incipient and mature gels. In the second regime, involving higher thrombin concentrations, the incipient gel formation time and the fractal characteristics of incipient and mature gels show little variation. The network formation is discussed in terms of computer simulations of incipient fractal networks by the activation-limited aggregation of clusters of rod-like particles. The significance of the work is discussed in terms of biomaterials design for applications involving controlled drug release and wound healing, and improved predictions of blood clot susceptibility to lysis.