Search

A solar evaporator that utilizes solar radiation energy can be a renewable approach to deal with energy crisis and fresh water shortage. In this study, a solar evaporator was prepared by assembling composite carbonized wood of

The development of human society has set unprecedented demands for advanced fiber materials, such as lightweight and high-performance fibers for reinforcement of composite materials in frontier fields and functional and intelligent fibers in wearable electronics. Carbonene materials composed of

Synthetic high-performance fibers, such as polyaramid fibers, have attracted particular attention owing to their excellent mechanical properties and promising applications in safety protection fields. However, fabricating fibers with high strength and toughness is challenging due to their intrinsic conflicts. Herein, we report a simultaneous improvement in strength and toughness of heterocyclic aramid fibers by 26% and 66%, respectively, via in situ polymerizing small amount (0.05 wt%) of short aminated single-walled carbon nanotube (SWNT) into heterocyclic aramid fibers, yielding 6.44 ± 0.11 GPa in tensile strength and 184.0 ± 11.4 MJ m−3 in toughness. Combined experimental evidences and atomistic simulations, it was uncovered that short aminated SWNTs with favorable dispersity and alignment significantly improve the crystallinity and orientation degree of heterocyclic aramid chains by a scope of 8.6 nm, and the in situ polymerization between short aminated SWNTs and heterocyclic aramid monomers increases the length of polymer chains and the interfacial interaction therein to promote stress transfer and suppress the strain localization. These two effects account for the simultaneous improvement in strength and toughness of heterocyclic aramid fibers via small addition of short aminated SWNTs. This composite manner of “small addition, big gains” through global optimization should guide further work on improving the strength and toughness of composites.

Natural biopolymers feature natural abundance, diverse chemical compositions, tunable properties, easy processability, excellent biocompatibility and biodegradability, as well as nontoxicity, providing new opportunities for the development of flexible sensing and energy devices. Generally, biopolymers are utilized as the passive and active building blocks to endow the flexible devices with mechanical robustness and good biocompatibility. This review aims to provide a comprehensive review on natural biopolymer-based sensing and energy devices. The diverse structures and fabrication processes of three typical biopolymers, including silk, cellulose, and chitin/chitosan, are presented. We review their utilities as the supporting substrates/matrix, active middle layers, separators, electrolytes, and active components of flexible sensing devices (sensors, actuators, transistors) and energy devices (batteries, supercapacitors, triboelectric nanogenerators). Finally, the remaining challenges and future research opportunities are discussed.

Flexible electronics have gained considerable research concern due to their wide prospect for health monitoring, soft robotics, and artificial intelligence, wherein flexible pressure sensors are necessary components of wearable devices. It is well known that the synergistic functions and multiscale structures of hybrid materials exert tremendous effects on the performance of flexible devices. Herein, inspired by the unique structure of the faceplate of sunflowers, we construct a hierarchical structure by in situ grown vertically aligned molybdenum disulfide (MoS2) nanosheets on carbonized silk fabric (MoS2/CSilk), which is applied as the sensing material in flexible pressure sensors. The MoS2/CSilk sensor displayed high sensitivity and good stability. We demonstrated its applications in monitoring subtle physiology signals, such as pulse wave and voice vibrations. In addition, it served as electrodes in lithium-ion batteries. The MoS2/CSilk electrode delivered ultrahigh first-cycle discharge and charge capacities of 2895 and 1594 mA h g-1, respectively. The MoS2/CSilk electrode exhibited a high capacity of 810 mA h g-1 with a CE close to 100% even after 300 cycles, suggesting good stability. The excellent overall performances are ascribed to the unique structure of the MoS2/CSilk and the synergistic effect of CSilk and MoS2. The concept and strategy of this work can be extended to the design and fabrication of other multifunctional devices.

The emerging two-dimensional (2D) materials have attracted explosive research interest, because of their unique properties and broad applications. However, the instability of typical 2D materials (...

Heteroatom doping in inert carbon matrixes has been widely adopted for efficient carbonaceous electrocatalysts. However, typical doping methods such as magnetic agitation and mechanical stirring may lead to a bad dispersion and thus poor reproducibility for electrocatalysis. Here, we proposed a strategy guided by the Murray's law to obtain hierarchically porous and highly graphitic carbons by cultivating rose flower in Ni(NO 3 ) 2 solution and pyrolyzing Ni-doped rose petals. The efficient Murray's network in the rose petals promotes uniform and sufficient transfer and absorption of Ni 2+ ions, which later serve as catalyst sites for highly graphitic carbons at high temperature. Because of the enhanced crystallinity of carbon that promotes the smooth transfer of electrons and the uniformly embedded Ni nanoparticles in the carbon matrix that serve as electrocatalytic active sites, the as-obtained carbons show superior performance as a bi-functional electrocatalyst for efficient overall water splitting.

Summary Electronic textile (E-textile) has drawn tremendous attention with the development of flexible and wearable electronics in recent years. Herein, we report the direct printing of E-textile composed of core-sheath fibers by employing a 3D printer equipped with a coaxial spinneret. Customer-designed core-sheath fiber-based patterns can be printed on textile for various purposes. For demonstration, we used carbon nanotubes (CNTs) as a conductive core and silk fibroin (SF) as a dielectric sheath, and fabricated a CNTs@SF core-sheath fiber-based smart pattern, which was further used as a triboelectricity nanogenerator textile. The smart textile could harvest biomechanical energy from human motion and achieve a power density as high as 18 mW/m2. We also demonstrated the printing of a supercapacitor textile for energy storage. The direct printing of smart patterns on textile may contribute to the large-scale production of self-sustainable E-textile with integrated electronics.

MXenes are an emerging class of highly conductive two-dimensional (2D) materials with electrochemical storage features. Oriented macroscopic Ti3C2Tx fibers can be fabricated from a colloidal 2D nematic phase dispersion. The layered conductive Ti3C2Tx fibers are ideal candidates for constructing high-speed ionic transport channels to enhance the electrochemical capacitive charge storage performance. In this work, we assemble Ti3C2Tx fibers with a high degree of flake orientation by a wet spinning process with controlled spinning speeds and morphology of the spinneret. In addition to the effects of cross-linking of magnesium ions between Ti3C2Tx flakes, the electronic conductivity and mechanical strength of the as-prepared fibers have been improved to 7200 S cm-1 and 118 MPa, respectively. The oriented Ti3C2Tx fibers present a volumetric capacitive charge storage capability of up to 1360 F cm-3 even in a Mg-ion based neutral electrolyte, with contributions from both nanofluidic ion transport and Mg-ion intercalation pseudocapacitance. The oriented 2D Ti3C2Tx driven nanofluidic channels with great electronic conductivity and mechanical strength endows the MXene fibers with attributes for serving as conductive ionic cables and active materials for fiber-type capacitive electrochemical energy storage, biosensors, and potentially biocompatible fibrillar tissues.

Protective clothing plays a vital role in safety and security. Traditional protective clothing can protect the human body from physical injury. It is highly desirable to integrate modern wearable electronics into a traditional protection suit to endow it with versatile smart functions. However, it is still challenging to integrate electronics into clothing through a practical approach while keeping the intrinsic flexibility and breathability of textiles. In this work, we realized the direct writing of laser-induced graphene (LIG) on a Kevlar textile in air and demonstrated the applications of the as-prepared Janus graphene/Kevlar textile in intelligent protective clothing. The C═O and N-C bonds in Kevlar were broken, and the remaining carbon atoms were reorganized into graphene, which can be ascribed to a photothermal effect induced by the laser irradiation. Proof-of-concept devices based on the prepared graphene/Kevlar textile, including flexible Zn-air batteries, electrocardiogram electrodes, and NO2 sensors, were demonstrated. Further, we fabricated self-powered and intelligent protective clothing based on the graphene/Kevlar textile. The laser-induced direct writing of graphene from commercial textiles in air conditions provides a versatile and rapid route for the fabrication of textile electronics.

Recently, wearable devices have been attracting significantly increased interest in human motion detection and human physiological signal monitoring. Currently, it is still a great challenge to fabricate strain sensors with high performance and good fit to the human body. In this work, we fabricated a close-fitting and wearable graphene textile strain sensor based on a graphene textile without polymer encapsulation. Graphene oxide acts as a colorant to dye the polyester fabric and is reduced at high temperature, which endows the graphene textile strain sensor with excellent performance. Compared with the previously reported strain sensors, our strain sensor exhibits a distinctive negative resistance variation with increasing strain. In addition, the sensor also demonstrates fascinating performance, including high sensitivity, long-term stability, and great comfort. Based on its superior performance, the graphene textile strain sensor can be knitted on clothing for detecting both subtle and large human motions, showing the tremendous potential for applications in wearable electronics.

Due to its excellent flexibility, graphene has an important application prospect in epidermal electronic sensors. However, there are drawbacks in current devices, such as sensitivity, range, lamination, and artistry. In this work, we have demonstrated a multilayer graphene epidermal electronic skin based on laser scribing graphene, whose patterns are programmable. A process has been developed to remove the unreduced graphene oxide. This method makes the epidermal electronic skin not only transferable to butterflies, human bodies, and any other objects inseparably and elegantly, merely with the assistance of water, but also have better sensitivity and stability. Therefore, pattern electronic skin could attach to every object like artwork. When packed in Ecoflex, electronic skin exhibits excellent performance, including ultrahigh sensitivity (gauge factor up to 673), large strain range (as high as 10%), and long-term stability. Therefore, many subtle physiological signals can be detected based on epidermal electronic skin with a single graphene line. Electronic skin with multiple graphene lines is employed to detect large-range human motion. To provide a deeper understanding of the resistance variation mechanism, a physical model is established to explain the relationship between the crack directions and electrical characteristics. These results show that graphene epidermal electronic skin has huge potential in health care and intelligent systems.

Stretchable and flexible supercapacitors are highly desired due to their many potential applications in wearable devices. However, it is challenging to fabricate supercapacitors that can withstand large tensile strain while maintaining high performance. Herein, we report an ultra-stretchable wire-shaped supercapacitor based on carbon nanotube@graphene@MnO2 fibers wound around a superelastic core fiber. The supercapacitor can sustain tensile strain up to 850%, which is the highest value reported for this type of device to date, while maintaining stable electrochemical performance. The energy density of the supercapacitor is 3.37 mWh·cm–3 at a power density of 54.0 mW·cm–3. The results show that 82% of the specific capacitance is retained after 1,000 stretch–release cycles with strains of 700%, demonstrating the superior durability of the elastic supercapacitor and showcasing its potential application in ultra-stretchable flexible electronics.

Natural energy haversting devices serve as an alternative candidate for power supply in many micro-/nano-systems. However, traditional nanogenerators based on piezoelectricity or triboelectric power generation face challenges in terms of biocompatibility and stability in various biological systems. The bacteriorhodopsin (bR) protein in Halobacterium halobium is an ideal biocompatible material for photoelectric conversion. Conventional bR systems based on ion transport or enhanced light absorption layers have a limited light power conversion speed. On the other hand, bR-based biohybrid devices have a great potential for sensitive light power conversion as compared to conventional nanogenerators. Herein, we present a biohybrid nanogenerator made of bR and horizontally aligned-long carbon nanotubes (CNTs) with electron–ion interaction for the first time for sensitive light power conversion. The bR layer serves as the proton pump, whereas CNTs are utilized to enhance the photocurrent; thus, the photocurrent frequency response improves significantly because of the effect of the electron–ion interaction. The photocurrent shows a linear relationship with the intensity of light and can still obtain a stable signal at a light intensity of 0.03 mW cm−2. With regard to the influence of the light on–off period, the photocurrent initially increases and then decreases with an increase in flickering frequency up to 360 Hz; this can be ascribed to the combinational influence of light switch speed and photocycle decay time. The photocurrent shows highest value (99 nA cm−2) at a frequency of about 50 Hz at a light intensity of 0.43 mW cm−2, which matches well with the frequency standard of the electrical power supply system. Moreover, we found that a higher density of CNTs contributed to improve performance of the nanogenerators. Furthermore, a H+ ion releasing model was proposed to interpret the operating mechanism of the biohybrid nanogenerator. The biohybrid nanogenerator shows great potential for applications as a power source for bio-nanosystems.

Flexible skin-mimicking electronics are highly desired for development of smart human-machine interfaces and wearable human-health monitors. Human skins are able to simultaneously detect different information, such as touch, friction, temperature, and humidity. However, due to the mutual interferences of sensors with different functions, it is still a big challenge to fabricate multifunctional electronic skins (E-skins). Herein, a combo temperature-pressure E-skin is reported through assembling a temperature sensor and a strain sensor in both of which flexible and transparent silk-nanofiber-derived carbon fiber membranes (SilkCFM) are used as the active material. The temperature sensor presents high temperature sensitivity of 0.81% per centigrade. The strain sensor shows an extremely high sensitivity with a gauge factor of ∼8350 at 50% strain, enabling the detection of subtle pressure stimuli that induce local strain. Importantly, the structure of the SilkCFM in each sensor is designed to be passive to other stimuli, enabling the integrated E-skin to precisely detect temperature and pressure at the same time. It is demonstrated that the E-skin can detect and distinguish exhaling, finger pressing, and spatial distribution of temperature and pressure, which cannot be realized using single mode sensors. The remarkable performance of the silk-based combo temperature-pressure sensor, together with its green and large-scalable fabrication process, promising its applications in human-machine interfaces and soft electronics.

Flexible and wearable sensors have drawn extensive concern due to their wide potential applications in wearable electronics and intelligent robots. Flexible sensors with high sensitivity, good flexibility, and excellent stability are highly desirable for monitoring human biomedical signals, movements and the environment. The active materials and the device structures are the keys to achieve high performance. Carbon nanomaterials, including carbon nanotubes (CNTs), graphene, carbon black and carbon nanofibers, are one of the most commonly used active materials for the fabrication of high-performance flexible sensors due to their superior properties. Especially, CNTs and graphene can be assembled into various multi-scaled macroscopic structures, including one dimensional fibers, two dimensional films and three dimensional architectures, endowing the facile design of flexible sensors for wide practical applications. In addition, the hybrid structured carbon materials derived from natural bio-materials also showed a bright prospect for applications in flexible sensors. This review provides a comprehensive presentation of flexible and wearable sensors based on the above various carbon materials. Following a brief introduction of flexible sensors and carbon materials, the fundamentals of typical flexible sensors, such as strain sensors, pressure sensors, temperature sensors and humidity sensors, are presented. Then, the latest progress of flexible sensors based on carbon materials, including the fabrication processes, performance and applications, are summarized. Finally, the remaining major challenges of carbon-based flexible electronics are discussed and the future research directions are proposed.

The unique structure of a vertically aligned carbon nanotube (VACNT) array makes it behave most similarly to a blackbody. It is reported that the optical absorptivity of an extremely black VACNT array is about 0.98-0.99 over a large spectral range of 200 nm-200 μm, inspiring us to explore the performance of VACNT arrays in solar energy harvesting. In this work, we report the highly efficient steam generation simply by laminating a layer of VACNT array on the surface of water to harvest solar energy. It is found that under solar illumination the temperature of upper water can significantly increase with obvious water steam generated, indicating the efficient solar energy harvesting and local temperature rise by the thin layer of VACNTs. We found that the evaporation rate of water assisted by VACNT arrays is 10 times that of bare water, which is the highest ratio for solar-thermal-steam generation ever reported. Remarkably, the solar thermal conversion efficiency reached 90%. The excellent performance could be ascribed to the strong optical absorption and local temperature rise induced by the VACNT layer, as well as the ultrafast water transport through the VACNT layer due to the frictionless wall of CNTs. Based on the above, we further demonstrated the application of VACNT arrays in solar-driven desalination.

With the rapid development of wearable devices, flexible pressure sensors with high sensitivity and wide workable range are highly desired. In nature, there are many well-adapted structures developed through natural selection, which inspired us for the design of biomimetic materials or devices. Particularly, human fingertip skin, where many epidermal ridges amplify external stimulations, might be a good example to imitate for highly sensitive sensors. In this work, based on unique chemical vapor depositions (CVD)-grown 3D graphene films that mimic the morphology of fingertip skin, we fabricated flexible pressure sensing membranes, which simultaneously showed a high sensitivity of 110 (kPa)−1 for 0–0.2 kPa and wide workable pressure range (up to 75 kPa). Hierarchical structured PDMS films molded from natural leaves were used as the supporting elastic films for the graphene films, which also contribute to the superior performance of the pressure sensors. The pressure sensor showed a low detection limit (0.2 Pa), fast response (< 30 ms), and excellent stability for more than 10,000 loading/unloading cycles. Based on these features, we demonstrated its applications in detecting tiny objects, sound, and human physiological signals, showing its potential in wearable electronics for health monitoring and human/machine interfaces.

The increasing demand of wearable electronic devices has promoted the development of high-performance flexible strain sensors which could monitor various physiological parameters. In this work, using silk georgette, which is a commercially available gauzy and lightweight fabric composed of highly twisted yarns in both warp and weft directions as the raw material, an ultrasensitive strain sensor with a wide workable strain range is fabricated through a facile and large-scale process. The obtained strain sensors exhibit remarkable combined features of ultrahigh sensitivity in a wide sensing range (average gauge factor of 29.7 within 40% strain and of 173.0 for a strain of 60–100%), ultralow detection limit (0.01% strain), high durability and stability (10 000 stretching cycles at 100% strain), fast response (

We report a sweat analysis patch based on silk-derived carbon textile for simultaneous detection of six health-related biomarkers., Wearable sweat analysis devices for monitoring of multiple health-related biomarkers with high sensitivity are highly desired for noninvasive and real-time monitoring of human health. Here, we report a flexible sweat analysis patch based on a silk fabric–derived carbon textile for simultaneous detection of six health-related biomarkers. The intrinsically N-doped graphitic structure and the hierarchical woven, porous structure provided the carbon textile good electrical conductivity, rich active sites, and good water wettability for efficient electron transmission and abundant access to reactants, enabling it to serve as an excellent working electrode in electrochemical sensors. On the basis of the above, we fabricated a multiplex sweat analysis patch that is capable of simultaneous detection of glucose, lactate, ascorbic acid, uric acid, Na+, and K+. The integration of selective detectors with signal collection and transmission components in this device has enabled us to realize real-time analysis of sweat.

Flexible enzymatic glucose sensors have been investigated extensively for health monitoring systems. However, enzymatic glucose sensors have some problems, such as poor stability and complicated immobilization procedures. Rational and controllable design of nanomaterials with a unique structure, high activity and good electrochemical performance for nonenzymatic glucose sensors is desired critically. In this paper, we synthesize cuprous oxide nanoparticles embedded in carbon spheres directly on carbonized silk fabrics (Cu2O NPs@CSs/CSF), which is further used for the fabrication of a flexible and self-supported non-enzymatic glucose sensor. The Cu2O NPs@CSs/CSF shows good electrical conductivity due to the large contact area and the stable connection between the carbonized silk fabrics and carbon spheres. We demonstrate that the as-obtained non-enzymatic glucose sensor possesses high sensitivity and good stability, indicating its potential for practical applications. This strategy diversifies the toolbox available to the field of nonenzymatic glucose sensors and holds promise for flexible electronic devices.

Graphene exhibits properties of atomic thickness, high transparency, and high carrier mobility, which is highly desirable for a flexible transparent conductive material. However, the electronic properties of large-area chemical vapor deposition grown graphene film suffer from insulated polymer contaminations introduced by the transfer process and the easily cracked nature. Here, we report a preparation method of a transfer-medium-free large-area nanofiber-reinforced graphene (a-PAN/G) film simply by annealing the electrostatically spun polyacrylonitrile (PAN) nanofibers on the graphene film. The film could be free-standing on water and suspended in air with high transparency and enhanced electrical and mechanical properties compared to that of a monolayer graphene film. The flexible transparent a-PAN/G films were demonstrated as active materials for sensitive pressure sensors. The obtained pressure sensors demonstrate high sensitivity (44.5 kPa-1 within 1.2 kPa), low operating voltage (0.01-0.5 V), and excellent stability for 5500 loading-unloading cycles, revealing promising potential applications in wearable electronics.

Silkworm silk is gaining significant attention from both the textile industry and research society because of its outstanding mechanical properties and lustrous appearance. The possibility of creating tougher silks attracts particular research interest. Carbon nanotubes and graphene are widely studied for their use as reinforcement. In this work, we report mechanically enhanced silk directly collected by feeding Bombyx mori larval silkworms with single-walled carbon nanotubes (SWNTs) and graphene. We found that parts of the fed carbon nanomaterials were incorporated into the as-spun silk fibers, whereas the others went into the excrement of silkworms. Spectroscopy study indicated that nanocarbon additions hindered the conformation transition of silk fibroin from random coil and α-helix to β-sheet, which may contribute to increased elongation at break and toughness modules. We further investigated the pyrolysis of modified silk, and a highly developed graphitic structure with obviously enhanced electrical conductivity was obtained through the introduction of SWNTs and graphene. The successful generation of these SWNT- or graphene-embedded silks by in vivo feeding is expected to open up possibilities for the large-scale production of high-strength silk fibers.

Recent years have witnessed the explosive development of flexible strain sensors. Nanomaterials have been widely utilized to fabricate flexible strain sensors, because of their high flexibility and electrical conductivity. However, the fabrication processes for nanomaterials and the subsequent strain sensors are generally complicated and are manufactured at high cost. In this work, we developed a facile dry-Meyer-rod-coating process to fabricate sheath-core-structured single-fiber strain sensors using ultrafine graphite flakes as the sheath and silk fibers as the core by virtue of their flexibility, high production, and low cost. The fabricated strain sensor exhibits a high sensitivity with a gauge factor of 14.5 within wide workable strain range up to 15%, and outstanding stability (up to 3000 cycles). The single-fiber-based strain sensors could be attached to a human body to detect joint motions or easily integrated into the multidirectional strain sensor for monitoring multiaxial strain, showing great potential applications as wearable strain sensors.

Silk is a widely available, edible, biocompatible, and environmentally sustainable natural material. Particulate matter (PM) pollution has drawn considerable attention because it is a serious threat to public health. Herein, we report a human-friendly silk nanofiber air filter, which exhibits superior filtration efficiency for both PM2.5 and submicron particles with obviously low pressure drop and low basis weight compared to typical commercial microfiber air filters. Additionally, other functions such as antibacterial activity could be easily integrated into the silk nanofiber air filters, enabling the fabrication of multifunctional air filters. All the above characteristics, combined with the natural abundance and biocompatibility of silk, suggest a great potential for the use of silk nanofibers as air filters, especially as comfortable and personal air purifiers.

This work presents a highly efficient and reliable strategy to grow horizontally aligned carbon nanotube (CNT) arrays on surfaces via preliminarily loading catalysts into the reactor. With the heat treatment before the growth of CNTs, the catalysts would migrate from the inner surface of the reactor to the surface of the targeted substrate to induce the growth of aligned CNTs. With this “in-situ catalyst loading” approach, aligned CNTs could be grown on different bare substrates, such as silicon, quartz and sapphire. The growth of CNTs could be repeated up to 50 times with reliable results via only one-time catalyst preloading process, avoiding the deposition of catalysts before each round of growth and the related randomicity, and thus benefiting the mass production of aligned CNT arrays on surfaces.

The development of nanomaterials has put forward high requirements for characterization techniques. Optical microscopy (OM), with easy accessibility and open operating spaces as compared to scanning electron microscopy, is a good choice to quickly locate materials and to be integrated with other equipment. However, OM is limited by its low resolution. Herein, we present a facile and non-destructive approach for optical observation of nanomaterials under conventional OMs with the aid of volatile nanoparticles (NPs), which can be deposited and removed in a controlled manner. The NPs deposited on the surface of nanomaterials render strong light scattering to enable the nanomaterials to become optically visible. For example, this approach enables the observation of individual carbon nanotubes (CNTs) with OMs at low magnification or even with the naked eye. Both supported CNTs on various substrates and suspended CNTs can be observed with this approach. Most importantly, the NPs can be completely removed through moderate heat treatment or laser irradiation, avoiding potential influence on the properties or subsequent applications of nanomaterials. Furthermore, we systematically investigate the deposition of various volatile NPs (up to 14 kinds) for the optical observation of nanomaterials. We also demonstrated the application of this approach on other nanomaterials, including nanowires and graphene. We showed that this approach is facile, controllable, non-destructive, and contamination-free, indicating wide potential applications.

Natural materials are often compositionally and structurally heterogeneous for realizing particular functions. Inspired by nature, researchers have designed hybrid materials that possess properties beyond each of the components. Particularly, it remains a great challenge to realize site‐specific anisotropy, which widely exists in natural materials and is responsible for unique mechanical properties as well as physiological behaviors. Herein, the spontaneous formation of aligned graphene oxide (GO) flakes in sodium alginate (SA) matrix with locally controlled orientation via a direct‐ink‐writing printing process is reported. The GO flakes are spontaneously aligned in the SA matrix by shear force when being extruded and then arranged horizontally after drying on the substrate, forming a brick‐and‐mortar structure that could anisotropically contract or expand upon activation by heat, light, or water. By designing the printing pathways directed by finite element analysis, the orientation of GO flakes in the composite is locally controlled, which could further guide the composite to transform into versatile architectures. Particularly, the transformation is reversible when water vapor is applied as one of the stimuli. As a proof of concept, complex morphing architectures are experimentally demonstrated, which are in good consistency with the simulation results., A multistimuli‐responsive composite with locally controlled texture that can be printed into programmable shape‐morphing architectures is presented. The printed structures show fast, reversible, and multistimuli‐responsive shape‐morphing toward heat, light, and water (liquid and vapor).

Silk has outstanding mechanical properties and biocompatibility. It has been used to fabricate traditional textiles for thousands of years and can be produced in large scale. Silk materials are potentially attractive in modern textile electronics. However, silk is not electrically conductive, thus limiting its applications in electronics. Moreover, regenerated silk is generally rigid and brittle, which hinder post processing. Here we report the fabrication of conductive silk wire in which carbon nanotube (CNT) yarns are wrapped with fluffy and flexible silk nanofiber films. The silk nanofiber film was prepared by electrospinning and then wrapped around a rotating CNT yarn in situ. The obtained silk-sheathed CNT (CNT@Silk) wire has an insulating sheath, which protects the body against electrical shock. In addition, the fabricated wires exhibit a high electrical conductivity (3.1 × 104 S/m), good mechanical strength (16 cN/tex), excellent flexibility, and high durability. More importantly, the wires have an...

3D graphene networks have shown extraordinary promise for high-performance electrochemical devices. Herein, the chemical vapor deposition synthesis of a highly porous 3D graphene foam (3D-GF) using naturally abundant calcined Iceland crystal as the template is reported. Intriguingly, the Iceland crystal transforms to CaO monolith with evenly distributed micro/meso/macropores through the releasing of CO2 at high temperature. Meanwhile, the hierarchical structure of the calcined template could be easily tuned under different calcination conditions. By precisely inheriting fine structure from the templates, the as-prepared 3D-GF possesses a tunable hierarchical porosity and low density. Thus, the hierarchical pores offer space for guest hybridization and provide an efficient pathway for ion/charge transport in typical energy conversion/storage systems. The 3D-GF skeleton electrode hybridized with Ni(OH)2 /Co(OH)2 through an optimal electrodeposition condition exhibits a high specific capacitance of 2922.2 F g-1 at a scan rate of 10 mV s-1 , and 2138.4 F g-1 at a discharge current density of 3.1 A g-1 . The hybrid 3D-GF symmetry supercapacitor shows a high energy density of 83.0 Wh kg-1 at a power density of 1011.3 W kg-1 and 31.4 Wh kg-1 at a high power density of 18 845.2 W kg-1 . The facile fabrication process enables the mass production of hierarchical porous 3D-GF for high-performance supercapacitors.

Recently, wearable pressure sensors have attracted tremendous attention because of their potential applications in monitoring physiological signals for human healthcare. Sensitivity and linearity are the two most essential parameters for pressure sensors. Although various designed micro/nanostructure morphologies have been introduced, the trade-off between sensitivity and linearity has not been well balanced. Human skin, which contains force receptors in a reticular layer, has a high sensitivity even for large external stimuli. Herein, inspired by the skin epidermis with high-performance force sensing, we have proposed a special surface morphology with spinosum microstructure of random distribution via the combination of an abrasive paper template and reduced graphene oxide. The sensitivity of the graphene pressure sensor with random distribution spinosum (RDS) microstructure is as high as 25.1 kPa–1 in a wide linearity range of 0–2.6 kPa. Our pressure sensor exhibits superior comprehensive properties com...

A three-dimensional carbon nanotube (CNT)/graphene hybrid material was synthesized by a two-step chemical vapor deposition (CVD) process. Due to the separated CVD processes for graphene and CNTs, the structures of the hybrid materials could be easily controlled. It is revealed that graphene film was tightly connected with one end of the CNT arrays, forming “jellyfish” structures. Moreover, our results indicate that the presence of graphene influenced the precipitation and growth rate of CNTs. The precipitation of CNTs was postponed due to the existence of graphene. However, the average growth rate of CNTs in the graphene region for the whole process was faster than that in the region without graphene.

There is a growing demand for flexible electronic devices. In particular, strain sensors with high performance have attracted more and more attention, because they can be attached on clothing or human skin for applications in the real-time monitoring of human activities. However, monitoring human-body motions that include both subtle and intensive motions, and many strain sensors cannot meet the diverse demands simultaneously. In this work, a silver nanoparticles (Ag NPs) bridged graphene strain sensor is developed for simultaneously detecting subtle and intensive human motions. Ag NPs serve as many bridges to connect the self-overlapping graphene sheets, which endows the strain sensor with many excellent performances. Because of the high sensitivity, with a large gauge factor (GF) of 475 and a strain range of >14.5%, high durability of the sensor has been achieved. Besides, the excellent consistency and repeatability of the fabrication process is verified. Furthermore, the model for explaining the working mechanism of the strain sensor is proposed. Most importantly, the designed wearable strain sensor can be applied in human motion detection, including large-scale motions and small-scale motions.

Tremendous progress has been made in the research of carbon nanotubes (CNTs) in the past 25 years, which has facilitated the progress and development of fundamental research and industrial applications. However, challenges and opportunities remain. At the same time, the discovery and development of graphene in 2004 has had an obvious impact on the applications of CNTs. The progress and development of CNTs provide valuable references for graphene, ranging from synthesis and characterization to applications. Promising materials combining CNTs and graphene are on the rise. The popularity of CNT/graphene hybrids has expanded research and application of carbon nanomaterials. In this chapter, we summarize the challenges and opportunities that exist in the synthesis and application of CNTs and describe the synthesis and application of CNT/graphene hybrid materials.

We report a facile graphene/graphite sheet assisted CVD process for the synthesis of high-areal-density HACNT arrays. Besides, some metal nanoparticles could eat the graphene/graphite sheets, forming serpentine holes on the sheets in the early stage, and finally leading to the precipitation of CNTs without an additional carbon source.

A novel carbonized plain-weave silk-fabric-based wearable strain sensor is proposed by Y. Y. Zhang and co-workers on page 6640. The sensor can be stretched up to 500% with high sensitivity in a wide strain range and can be assembled into wearable devices for the detection of both large and subtle human activities, showing great potential in human-motion detection and robotics.

A carbonized plain-weave silk fabric is fabricated into wearable and robust strain sensors, which can be stretched up to 500% and show high sensitivity in a wide strain range. This sensor can be assembled into wearable devices for detection of both large and subtle human activities, showing great potential for monitoring human motions and personal health.