Search

We proposed and fabricated a miniaturized multi-core fiber grating vibration sensor. The size of the miniaturized vibration sensor is 10mm × 10mm × 10 mm with a mass of only 0.25g. Finite element analysis and experimental tests were carried out to validate the performance of the vibration sensor. The experiment results indicate that the sensor has a sensitivity of 68.72 pm/g in the X direction and 64.52 pm/g in the Y direction within the operating frequency range of 20–240Hz. The cross-interference between the two directions of vibration measurement falls within 4 %. The sensor is suitable for measuring mechanical vibrations in the mid-low frequency range, especially in cases where size, quality, and distributed measurement are of particular concern.

We proposed and fabricated a miniaturized multi-core fiber grating vibration sensor. The size of the miniaturized vibration sensor is 10mm × 10mm × 10 mm with a mass of only 0.25g. Finite element analysis and experimental tests were carried out to validate the performance of the vibration sensor. The experiment results indicate that the sensor has a sensitivity of 68.72 pm/g in the X direction and 64.52 pm/g in the Y direction within the operating frequency range of 20-240Hz. The cross-interference between the two directions of vibration measurement falls within 4 %. The sensor is suitable for measuring mechanical vibrations in the mid-low frequency range, especially in cases where size, quality, and distributed measurement are of particular concern., Competing Interests: The authors declare no conflicts of interest., (© 2024 The Authors.)

Since optical submarine cable systems are a part of the global communications infrastructure, their total capacity must be continuously and dramatically enlarged. Recently, methods how to maximize the transmission capacity under electrical power limitations have been studied, and it has been reported that a single band (C-band only) transmission system with more fiber pairs (FPs) could be a promising technology. This finding has triggered work on submarine cables with more FPs. For a further increase in FPs in optical submarine cable systems, which also have space limitations in existing cable designs, space-division multiplexing (SDM) technologies such as multi-core fibers (MCFs) and multi-mode fibers (MMFs) could be promising solutions. In particular, 125-μm standard cladding SDM fibers are attractive for early deployment in submarine cable systems since they are expected to have high productivity and high mechanical reliability similar to existing single-mode fibers (SMFs) with the same cladding diameter. In this paper, we report transpacific MCF transmission over a 30-nm bandwidth using standard cladding ultralow-loss coupled 4-core fibers, extending our previous work. The Q2-factors of 608 (4 core × 152 WDM) SDM/WDM channels modulated with 24-Gbaud DP (dual polarization)-QPSK (quadrature phase shift keying) exceeded the assumed forward error correction (FEC) limits after a 9,150-km transmission. As a result, transmission capacity of 50.47 Tbit/s and a capacity-distance product of 461.8 Pbit/s·km were achieved for standard cladding diameter SDM fibers. [ABSTRACT FROM AUTHOR]

Space-division multiplexing (SDM) is an attractive technique for dramatically enhancing the transmission capacity in a single optical fiber. Recently, ultradense SDM transmission experimentswith a spatial multiplicity of over 100 have been reported by using few mode multicore fibers (FM-MCFs). Considering the maximum capacity of around 100 Tb/s reported in single-mode single-core fiber transmission experiments, the capacity in FMMCF transmission with more than 100 spatial channels is expected to reach 10 peta-b/s; however, the maximum capacity has been limited to 2 peta-b/s. In this paper, we demonstrate ultradense SDM transmission of 739 WDM 12-Gbd dual polarization-64- quadrature amplitude modulation (QAM)/16-QAM signals over 11.3-km 6-mode 19-core fiber using the C+L band, achieving a record fiber capacity of 10.16 peta-b/s with an aggregate spectral efficiency of 1099.9 b/s/Hz. [ABSTRACT FROM AUTHOR]

In this paper, we have proposed a high-capacity backhaul network, which is based on mixed fiber-wireless systems using millimeter-wave radio-over-multi-core fiber (MMW RoMCF) and multiple-input multiple-output (MIMO) transmission, for next generation mobile access networks. In addition, we also investigate the use of avalanche photodiode (APD) to improve capacity of the proposed backhaul downlink. We then theoretically analyze the system capacity comprehensively while considering various physical impairments including noise, MCF crosstalk, and fading modeled by Rician MIMO channel. The feasibility of the proposed backhaul architecture is verified via the numerical simulation experiments. The research results demonstrate that our developed backhaul solution can significantly enhance the backhaul capacity; the system capacity of 24 bps/Hz can be achieved with 20-km 8-core MCF and 8 × 8 MIMO transmitted over 100-m Rician fading link. It is also shown that the system performance, in term of channel capacity, strongly depend on the MCF inter-core crosstalk, which is governed by the mode coupling coefficient, the core pitch, and the bending radius. [ABSTRACT FROM AUTHOR]

Space-division multiplexing (SDM) using multi-core fibers (MCFs) and few-mode fibers (FMFs) was proposed as a solution to increase capacity and/or reduce the cost per bit of fiber-optic transmission. Advances in passive and active SDM devices as well as digital signal processing have led to impressive SDM transmission demonstrations in the laboratory. Although the perceived advantages in terms of capacity and cost per bit that SDM offers over parallel SMF bundles are not universally accepted, SDM is beginning to emerge as an indispensable solution in major network segments. The introduction of the spatial degree of freedom allows optical networks to overcome fundamental limitations such as fiber nonlinearity as well practical limitations such as power delivery. We describe these application scenarios that the optical communications industry has already began to explore. From a fundamental science point of view, concepts such as the principal modes, generalized Stokes space, and multi-component solitons discovered in SDM research will likely have a broad impact in other areas of science and engineering. [ABSTRACT FROM AUTHOR]

It is often observed that various differential mode delays (DMDs) coexist in single multi-core fiber (MCF) and/or few-mode fiber (FMF) transmission. From a multi-input and multi-output (MIMO) equalization perspective, this indicates optimum equalization tap length for each multi-core and/or multi-mode signal varies according to its DMD. Correspondingly, complex calculation of finding each optimum tap length is necessary to obtain satisfactory performance. This paper presents a new adaptive MIMO equalization method to deal with various DMDs while avoiding such complex calculation. The method uses the same tap length for all multi-core and/or multi-mode signals according to the maximum DMD to reduce the calculation cost. To rectify negative effects such as noise enhancement due to the non-optimum tap length setting, the method applies the improved proportionate normalized least mean square (IPNLMS) with leveraged equalization coefficients update on the basis of the overall sparsity of coefficients. IPNLMS inherently updates equalization coefficients by proportionately promoting the previous coefficients in order that the coefficients of signal part are promoted while those of noise part are suppressed. To determine the IPNLMS parameters that govern the amount of the promotion, the presented method uses a simple sparsity metric that calculates the overall sparsity of coefficients. Then, the sparsity metric is mapped to IPNLMS parameters in a manner that the overall sparsity of coefficients is progressively facilitated as adaptation. Evaluations using experimental data of FMF transmission over 527 km end-to-end with 33.2 ns maximum DMD show the presented method effectively deals with various DMDs to suppress the noise and obtains 0.7 dB of Q-factor performance enhancement comparing to the conventional method. [ABSTRACT FROM PUBLISHER]

In the past few years, many researchers have studied elastic optical networks, which exhibit a dramatically improved transmission capacity compared with conventional optical networks. However, the transmission capacity per fiber will soon reach the physical limit for traditional single-mode fibers. Multicore fiber (MCF) is among the innovative fibers based on space-division multiplexing technology. MCF has multiple cores and achieves a far larger transmission capacity than traditional single-mode fibers. However, signals transmitted in these crowded multiple cores interfere with each other and are degraded. This degradation has a serious impact on the network resource management in elastic optical networks. Previous research indicates that the crosstalk effect of MCF is dependent on an arrangement of signals regarding the spectrum and core. Therefore, we approach the problem of the crosstalk in MCF with regard to the spectrum and core allocation, from the network perspective. First, this paper summarizes the related work regarding elastic optical networks and MCFs. Next, we propose an ?on-demand? spectrum and core allocation method that reduces both the crosstalk and fragmentation in elastic optical networks with MCFs. This proposed method is based on two predefined policies related to the crosstalk and fragmentation. The first, the core prioritization policy, is based on the MCF's structure, and the other is a core classification policy based on the required bandwidth of the connections. The core prioritization policy realizes the core allocation that reduces crosstalk by avoiding filling adjacent cores. The core classification policy reduces the spectrum fragmentation by allocating a uniform bandwidth connection for each core. Finally, we evaluate the proposed method using computer simulations. The results indicate that the proposed method can, under various network conditions, improve both the crosstalk and blocking probability of the total network through our two policies. [ABSTRACT FROM PUBLISHER]

Recently, space-division multiplexing (SDM) techniques using multi-core fiber (MCF) and few-mode fiber (FMF) have been introduced into optical fiber communication to increase transmission capacity. Two main types of optical fiber amplifiers based on the Erbiumdoped fiber (EDF) and the Raman effect have been developed to amplify signals in the MCF and FMF. In this paper, we reviewed the principles and configurations of these amplifiers. [ABSTRACT FROM AUTHOR]