Search

Ultraviolet germicidal irradiation (UVGI) is known to inactivate various viruses and bacteria, including SARS-CoV-2, and is widely applied especially in medical facilities. This inactivation results from the high photon energies causing molecular bonds to break, but when nonpathogen molecules are affected, unwanted effects may occur. Here, we explored the effect of a commercial high intensity (similar to 2 kW) UVC disinfection device on the composition and concentration of gases and particles in indoor air. We find that the UVC (254 nm) caused dramatic increases in particle number concentrations, and nearly all (similar to 1000) monitored gas phase species also increased. These responses were unsurprising when considering the typical impacts of UVC on atmospheric chemistry. High particle concentrations are associated with adverse health effects, suggesting that the impact of UVGI devices on indoor air quality (IAQ) should be studied in much more detail. The high-intensity device in this study was intended for short durations in unoccupied rooms, but lower-intensity devices for continuous use in occupied rooms are also widely applied. This makes further studies even more urgent, as the potential IAQ effects of these approaches remain largely unexplored.

Condensable vapors, including highly oxygenated organic molecules (HOM), govern secondary organic aerosol formation and thereby impact the amount, composition, and properties (e.g. toxicity) of aerosol particles. These vapors are mainly formed in the atmosphere through the oxidation of volatile organic compounds (VOCs). Urban environments contain a variety of VOCs from both anthropogenic and biogenic sources, as well as other species, for instance nitrogen oxides (NOx), that can greatly influence the formation pathways of condensable vapors like HOM. During the last decade, our understanding of HOM composition and formation has increased dramatically, with most experiments performed in forests or in heavily polluted urban areas. However, studies on the main sources for condensable vapors and secondary organic aerosols (SOA) in biogenically influenced urban areas, such as suburbs or small cities, has been limited. Here, we studied the HOM composition, measured with two nitrate-based chemical ionization mass spectrometers and analyzed using positive matrix factorization (PMF), during late spring at two locations in Helsinki, Finland. Comparing the measured concentrations at a street canyon site and a nearby urban background station, we found a strong influence of NOx on the HOM formation at both stations, in agreement with previous studies conducted in urban areas. Even though both stations are dominated by anthropogenic VOCs, most of the identified condensable vapors originated from biogenic precursors. This implies that in Helsinki anthropogenic activities mainly influence HOM formation by the effect of NOx on the biogenic VOC oxidation. At the urban background station, we found condensable vapors formed from two biogenic VOC groups (monoterpenes and sesquiterpenes), while at the street canyon, the only identified biogenic HOM precursor was monoterpenes. At the street canyon, we also observed oxidation products of aliphatic VOCs, which were not observed at the urban background station. The only factors that clearly correlate (temporally and composition-wise) between the two stations contained monoterpene-derived dimers. This suggests that HOM composition and formation mechanisms are strongly dependent on localized emissions and the oxidative environment in these biogenically influenced urban areas, and they can change considerably also within distances of one kilometer within the urban environment.

Highly oxygenated organic molecules (HOMs) from α-pinene ozonolysis have been shown to be significant contributors to secondary organic aerosol (SOA), yet our mechanistic understanding of how the peroxy-radical-driven autoxidation leads to their formation in this system is still limited. The involved isomerisation reactions such as H-atom abstractions followed by O2 additions can take place on sub-second timescales in short-lived intermediates, making the process challenging to study. Similarly, while the end-products and sometimes radical intermediates can be observed using mass spectrometry, their structures remain elusive. Therefore, we propose a method utilising selective deuterations for unveiling the mechanisms of autoxidation, where the HOM products can be used to infer which C atoms have taken part in the isomerisation reactions. This relies on the fact that if a C−D bond is broken due to an abstraction by a peroxy group forming a −OOD hydroperoxide, the D atom will become labile and able to be exchanged with a hydrogen atom in water vapour (H2O), effectively leading to loss of the D atom from the molecule. In this study, we test the applicability of this method using three differently deuterated versions of α-pinene with the newly developed chemical ionisation Orbitrap (CI-Orbitrap) mass spectrometer to inspect the oxidation products. The high mass-resolving power of the Orbitrap is critical, as it allows the unambiguous separation of molecules with a D atom (mD=2.0141) from those with two H atoms (mH2=2.0157). We found that the method worked well, and we could deduce that two of the three tested compounds had lost D atoms during oxidation, suggesting that those deuterated positions were actively involved in the autoxidation process. Surprisingly, the deuterations were not observed to decrease HOM molar yields, as would have been expected due to kinetic isotope effects. This may be an indication that the relevant H (or D) abstractions were fast enough that no competing pathways were of relevance despite slower abstraction rates of the D atom. We show that selective deuteration can be a very useful method for studying autoxidation on a molecular level and likely is not limited to the system of α-pinene ozonolysis tested here.

Diterpenes (C20H32) are biogenically emitted volatile compounds that only recently have been observed in ambient air. They are expected to be highly reactive, and their oxidation is likely to form condensable vapors. However, until now, no studies have investigated gas-phase diterpene oxidation. In this paper, we explored the ozonolysis of a diterpene, ent-kaurene, in a simulation chamber. Using state-of-the-art mass spectrometry, we characterized diterpene oxidation products for the first time, and we identified several products with varying oxidation levels, including highly oxygenated organic molecules (HOM), monomers, and dimers. The most abundant monomers measured using a nitrate chemical ionization mass spectrometer were C19H28O8 and C20H30O5, and the most abundant dimers were C38H60O6 and C39H62O6. The exact molar yield of HOM from kaurene ozonolysis was hard to quantify due to uncertainties in both the kaurene and HOM concentrations, but our best estimate was a few percent, which is similar to values reported earlier for many monoterpenes. We also monitored the decrease in the gas-phase oxidation products in response to an increased condensation sink in the chamber to deduce their affinity to condense. The oxygen content was a critical parameter affecting the volatility of products, with four to five O atoms needed for the main monomeric species to condense onto 80 nm particles. Finally, we report on the observed fragmentation and clustering patterns of kaurene in a Vocus proton-transfer-reaction time-of-flight mass spectrometer. Our findings highlight similarities and differences between diterpenes and smaller terpenes during their atmospheric oxidation, but more studies on different diterpenes are needed for a broader view of their role in atmospheric chemistry.

Highly oxygenated compounds are important contributors to the formation and growth of atmospheric organic aerosol and thus have an impact on Earth’s radiation balance and global climate. However, knowledge of the contribution of highly oxygenated compounds to organic aerosol and their fate after condensing into the particle phase has been limited by the lack of suitable detection techniques. Here, we present a new online method for measuring highly oxygenated compounds from organic aerosol. The method includes thermal evaporation of particles in a new inlet, the vaporization inlet for aerosols (VIA), followed by identification of the evaporated highly oxygenated compounds by a nitrate chemical ionization mass spectrometer (NO3-CIMS). The method does not require sample collection, enabling highly time-resolved measurements of particulate compounds. We evaluate the performance of the method by measuring the detection limit and performing background measurements. We estimate a detection limit of below 1 ng m−3 for a single compound and below 1 µg m−3 for SOA with the sampling setup used here. These detection limits can be improved upon by optimizing the flow setup. Furthermore, we detect hundreds of particulate highly oxygenated compounds from organic aerosol generated from different precursors. Our results are consistent with previous studies showing that the volatility of organic compounds decreases with increasing m/z ratio and level of oxygenation and that organic aerosol consists of monomers and oligomeric compounds. By comparing the gas- and particle-phase compounds, we found indications of potential particle-phase reactions occurring in organic aerosol. Future work will focus both on further improving the sampling design and on better understanding the evaporation dynamics of the system, but already these initial tests show that the VIA coupled to the NO3-CIMS is a promising method for investigating the transformations and fate of the compounds after condensing into the particle phase.

Oxygenated organic molecules (OOMs) are the crucial intermediates linking volatile organic compounds (VOCs) to secondary organic aerosols (SOAs) in the atmosphere, but comprehensive understanding of the characteristics of OOMs and their formation from VOCs is still missing. Ambient observations of OOMs using recently developed mass spectrometry techniques are still limited, especially in polluted urban atmospheres where VOCs and oxidants are extremely variable and complex. Here, we investigate OOMs, measured by a nitrate-ion-based chemical ionization mass spectrometer at Nanjing in eastern China, through performing positive matrix factorization on binned mass spectra (binPMF). The binPMF analysis reveals three factors about anthropogenic VOC (AVOC) daytime chemistry, three isoprene-related factors, three factors about biogenic VOC (BVOC) nighttime chemistry, and three factors about nitrated phenols. All factors are influenced by NOx in different ways and to different extents. Over 1000 non-nitro molecules have been identified and then reconstructed from the selected solution of binPMF, and about 72 % of the total signals are contributed by nitrogen-containing OOMs, mostly regarded as organic nitrates formed through peroxy radicals terminated by nitric oxide or nitrate-radical-initiated oxidations. Moreover, multi-nitrates account for about 24 % of the total signals, indicating the significant presence of multiple generations, especially for isoprene (e.g., C5H10O8N2 and C5H9O10N3). Additionally, the distribution of OOM concentration on the carbon number confirms their precursors are driven by AVOCs mixed with enhanced BVOCs during summer. Our results highlight the decisive role of NOx in OOM formation in densely populated areas, and we encourage more studies on the dramatic interactions between anthropogenic and biogenic emissions.

Highly oxygenated organic molecules (HOM) are important for the formation of secondary organic aerosol (SOA), which poses serious health risks and exerts great influence on Earth’s climate. However, the speciation of particle-phase HOM and its relationship with gas-phase HOM formation has been limited by the lack of suitable analytical techniques. Here, combining a novel particle evaporation inlet VIA (Volatilization Inlet for Aerosols) with a nitrate chemical ionization mass spectrometer (NO3-CIMS), gas- and particle-phase HOM products of α-pinene ozonolysis were studied under different conditions. Within the 50-min residence time of our Teflon chamber, we observed enhancement of C16-C19 HOM dimers in particles compared to the HOM that were condensing. In particular, gas-phase dimer formation was considerably suppressed in experiments with the addition of CO or NO, but dimers still made up a considerable fraction of the observed SOA. In addition to the generally shorter carbon skeletons of the particle phase dimers (i.e. C16-C19) compared to the gas phase (C19-C20), average O / C ratios of the HOM (especially in the dimer range) also decreased slightly in the particle phase. C17H26Oz compounds, which have often been reported by previous offline measurements, dominate the particle-phase HOM mass spectra in α-pinene ozonolysis experiments. Our results indicate that these C17 compounds might be related to particle-phase processes within one hour after HOM condensation. However, the new VIA-NO3-CIMS system used in this work will require more detailed characterization to better understand how the thermal desorption and wall effects may modify the measured particle-phase HOM distributions. Nevertheless, for example organic nitrate measured by this novel VIA-NO3-CIMS system was consistent with the measurements of an Aerodyne Aerosol Mass Spectrometer (AMS), showing the capability of this system as a promising technique for particle-phase HOM measurements. Taken together, we believe that this system is a promising technique for combined online gas- and particle-phase HOM measurements.

Orbitrap Fourier transform mass spectrometry coupled with chemical ionization (CI) is a new-generation technique for online analysis in atmospheric chemistry. The advantage of the high resolving power of the CI-Orbitrap has been compromised by its relatively low sensitivity to trace compounds (e.g.,10

Highly oxygenated organic molecules (HOMs) are important sources of atmospheric aerosols. Resolving the molecular-level formation mechanisms of these HOMs from freshly emitted hydrocarbons improves the understanding of aerosol properties and their influence on the climate. In this study, we measure the electrical mobility and mass-to-charge ratio of α-pinene oxidation products using a secondary electrospray-differential mobility analyzer-mass spectrometer (SESI-DMA-MS). The mass-mobility spectrum of the oxidation products is measured with seven different reagent ions generated by the electrospray. We analyzed the mobility-mass spectra of the oxidation products C9-10H14-18O2-6. Our results show that acetate and chloride yield the highest charging efficiencies. Analysis of the mobility spectra suggests that the clusters have 1-5 isomeric structures (i.e., ion-molecule cluster structures with distinct mobilities), and the number is affected by the reagent ion. Most of the isomers are likely cluster isomers originating from binding of the reagent ion to different sites of the molecule. By comparing the number of observed isomers and measured mobilities and collision cross sections between standard pinanediol and pinonic acid to the values observed for C10H18O2 and C10H16O3 produced from oxidation of α-pinene, we confirm that pinanediol and pinonic acid are the only isomers for these elemental compositions in our experimental conditions. Our study shows that the SESI-DMA-MS produces new information from the first steps of oxidation of α-pinene. publishedVersion

Aromatic hydrocarbons are a class of volatile organic compounds associated with anthropogenic activity and make up a significant fraction of urban volatile organic compound (VOC) emissions that contribute to the formation of secondary organic aerosol (SOA). Benzene is one of the most abundant species emitted from vehicles, biomass burning and industry. An iodide time-of-flight chemical ionisation mass spectrometer (ToF-CIMS) and nitrate ToF-CIMS were deployed at the Julich Plant Atmosphere Chamber as part of a series of experiments examining benzene oxidation by OH under high- and low-NO x conditions, where a range of organic oxidation products were detected. The nitrate scheme detects many oxidation products with high masses, ranging from intermediate volatile organic compounds (IVOCs) to extremely low volatile organic compounds (ELVOCs), including C 12 dimers. In comparison, very few species with C ≥6 and O ≥8 were detected with the iodide scheme, which detected many more IVOCs and semi-volatile organic compounds (SVOCs) but very few ELVOCs and low volatile organic compounds (LVOCs). A total of 132 and 195 CHO and CHON oxidation products are detected by the iodide ToF-CIMS in the low- and high-NO x experiments respectively. Ring-breaking products make up the dominant fraction of detected signal and 21 and 26 of the products listed in the Master Chemical Mechanism (MCM) were detected. The time series of highly oxidised (O ≥6 ) and ring-retaining oxidation products (C 6 and double-bond equivalent = 4) equilibrate quickly, characterised by a square form profile, compared to MCM and ring-breaking products which increase throughout oxidation, exhibiting sawtooth profiles. Under low-NO x conditions, all CHO formulae attributed to radical termination reactions of first-generation benzene products, and first-generation auto-oxidation products are observed. Several N-containing species that are either first-generation benzene products or first-generation auto-oxidation products are also observed under high-NO x conditions. Hierarchical cluster analysis finds four clusters, of which two describe photo-oxidation. Cluster 2 shows a negative dependency on the NO 2 / NO x ratio, indicating it is sensitive to NO concentration and thus likely to contain NO addition products and alkoxy-derived termination products. This cluster has the highest average carbon oxidation state ( OS C ‾ ) and the lowest average carbon number. Where nitrogen is present in a cluster member of cluster 2, the oxygen number is even, as expected for alkoxy-derived products. In contrast, cluster 1 shows no dependency on the NO 2 / NO x ratio and so is likely to contain more NO 2 addition and peroxy-derived termination products. This cluster contains fewer fragmented species, as the average carbon number is higher and OS C ‾ lower than cluster 2, and more species with an odd number of oxygen atoms. This suggests that clustering of time series which have features pertaining to distinct chemical regimes, for example, NO 2 / NO x perturbations, coupled with a priori knowledge, can provide insight into identification of potential functionality.

Proton transfer reaction (PTR) is a commonly applied ionization technique for mass spectrometers, in which hydronium ions (H3O+) transfer a proton to analytes with higher proton affinities than the water molecule. This method has most commonly been used to quantify volatile hydrocarbons, but later-generation PTR instruments have been designed for better throughput of less volatile species, allowing detection of more functionalized molecules as well. For example, the recently developed Vocus PTR time-of-flight mass spectrometer (PTR-TOF) has been shown to agree well with an iodide-adduct-based chemical ionization mass spectrometer (CIMS) for products with 3–5 O atoms from oxidation of monoterpenes (C10H16). However, while several different types of CIMS instruments (including those using iodide) detect abundant signals also at “dimeric” species, believed to be primarily ROOR peroxides, no such signals have been observed in the Vocus PTR even though these compounds fulfil the condition of having higher proton affinity than water. More traditional PTR instruments have been limited to volatile molecules as the inlets have not been designed for transmission of easily condensable species. Some newer instruments, like the Vocus PTR, have overcome this limitation but are still not able to detect the full range of functionalized products, suggesting that other limitations need to be considered. One such limitation, well-documented in PTR literature, is the tendency of protonation to lead to fragmentation of some analytes. In this work, we evaluate the potential for PTR to detect dimers and the most oxygenated compounds as these have been shown to be crucial for forming atmospheric aerosol particles. We studied the detection of dimers using a Vocus PTR-TOF in laboratory experiments, as well as through quantum chemical calculations. Only noisy signals of potential dimers were observed during experiments on the ozonolysis of the monoterpene α-pinene, while a few small signals of dimeric compounds were detected during the ozonolysis of cyclohexene. During the latter experiments, we also tested varying the pressures and electric fields in the ionization region of the Vocus PTR-TOF, finding that only small improvements were possible in the relative dimer contributions. Calculations for model ROOR and ROOH systems showed that most of these peroxides should fragment partially following protonation. With the inclusion of additional energy from the ion–molecule collisions driven by the electric fields in the ionization source, computational results suggest substantial or nearly complete fragmentation of dimers. Our study thus suggests that while the improved versions of PTR-based mass spectrometers are very powerful tools for measuring hydrocarbons and their moderately oxidized products, other types of CIMS are likely more suitable for the detection of ROOR and ROOH species.

The understanding at a molecular level of ambient secondary organic aerosol (SOA) formation is hampered by poorly constrained formation mechanisms and insufficient analytical methods. Especially in developing countries, SOA related haze is a great concern due to its significant effects on climate and human health. We present simultaneous measurements of gas-phase volatile organic compounds (VOCs), oxygenated organic molecules (OOMs), and particle-phase SOA in Beijing. We show that condensation of the measured OOMs explains 26-39% of the organic aerosol mass growth, with the contribution of OOMs to SOA enhanced during severe haze episodes. Our novel results provide a quantitative molecular connection from anthropogenic emissions to condensable organic oxidation product vapors, their concentration in particle-phase SOA, and ultimately to haze formation.

Particulate organic nitrate (pON) can be a major part of secondary organic aerosol (SOA) and is commonly quantified by indirect means from aerosol mass spectrometer (AMS) data. However, pON quantification remains challenging. Here, we set out to quantify and characterize pON in the boreal forest, through direct field observations at Station for Measuring Ecosystem Atmosphere Relationships (SMEAR) II in Hyytia''la'', Finland, and targeted single precursor laboratory studies. We utilized a long time-of-flight AMS (LToF-AMS) for aerosol chemical characterization, with a particular focus to identify CxHyOzN+ ("CHON+") fragments. We estimate that during springtime at SMEAR II, pON (including both the organic and nitrate part) accounts for similar to 10% of the particle mass concentration (calculated by the NO+/NO2+ method) and originates mainly from the NO3 radical oxidation of biogenic volatile organic compounds. The majority of the background nitrate aerosol measured is organic. The CHON+ fragment analysis was largely unsuccessful at SMEAR II, mainly due to low concentrations of the few detected fragments. However, our findings may be useful at other sites as we identified 80 unique CHON+ fragments from the laboratory measurements of SOA formed from NO3 radical oxidation of three pON precursors (beta-pinene, limonene, and guaiacol). Finally, we noted a significant effect on ion identification during the LToF-AMS high-resolution data processing, resulting in too many ions being fit, depending on whether tungsten ions (W+) were used in the peak width determination. Although this phenomenon may be instrument-specific, we encourage all (LTOF-) AMS users to investigate this effect on their instrument to reduce the possibility of incorrect identifications.

At SMEAR II research station in Hyytiälä, located in the Finnish boreal forest, the process of new particle formation and the role of ions has been investigated for almost 20 years near the ground and at canopy level. However, above SMEAR II, the vertical distribution and diurnal variation of these different atmospheric ions are poorly characterized. In this study, we assess the atmospheric ion composition in the stable boundary layer, residual layer, mixing layer, and free troposphere, and the evolution of these atmospheric ions due to photochemistry and turbulent mixing through the day. To measure the vertical profile of atmospheric ions, we developed a tailored set-up for online mass spectrometric measurements, capable of being deployed in a Cessna 172 with minimal modifications. Simultaneously, instruments dedicated to aerosol properties made measurements in a second Cessna. We conducted a total of 16 measurement flights in May 2017, during the spring, which is the most active new particle formation season. A flight day typically consisted of three distinct flights through the day (dawn, morning, and afternoon) to observe the diurnal variation and at different altitudes (from 100 to 3200 m above ground), to capture the boundary layer development from the stable boundary layer, residual layer to mixing layer, and the free troposphere. Our observations showed that the ion composition is distinctly different in each layer and depends on the air mass origin and time of the day. Before sunrise, the layers are separated from each other and have their own ion chemistry. We observed that the ions present within the stable layer are of the same composition as the ions measured at the canopy level. During daytime when the mixing layer evolved and the compounds are vertically mixed, we observed that highly oxidized organic molecules are distributed to the top of the boundary layer. The ion composition in the residual layer varies with each day, showing similarities with either the stable boundary layer or the free troposphere. Finally, within the free troposphere, we detected a variety of carboxylic acids and ions that are likely containing halogens, originating from the Arctic Sea.

Proton-transfer-reaction (PTR) is a commonly applied ionization technique for mass spectrometers, where hydronium ions (H3O+) transfer a proton to analytes with higher proton affinities than the water molecule. This method has most commonly been used to quantify volatile hydrocarbons, but later generation PTR-instruments have been designed for better throughput of less volatile species, allowing detection of more functionalized molecules as well. For example, the recently developed Vocus PTR time-of-flight mass spectrometer (PTR-TOF) has been shown to agree well with an iodide adduct based chemical ionization mass spectrometer (CIMS) for products with 3-5 O-atoms from oxidation of monoterpenes (C10H16). However, while several different types of CIMS instruments (including those using iodide) detect abundant signals also at “dimeric” species, believed to be primarily ROOR peroxides, no such signals have been observed in the Vocus PTR, even though these compounds fulfil the condition of having higher proton affinity than water. More traditional PTR instruments have been limited to volatile molecules as the inlets have not been designed for transmission of easily condensable species. Some newer instruments, like the Vocus PTR, have overcome this limitation, but are still not able to detect the full range of functionalized products, suggesting that other limitations need to be considered. One such limitation, well-documented in PTR literature, is the tendency of protonation to lead to fragmentation of some analytes. In this work, we evaluate the potential for PTR to detect dimers and the most oxygenated compounds, as these have been shown to be crucial for forming atmospheric aerosol particles. We studied the detection of dimers using a Vocus PTR-TOF in laboratory experiments as well as through quantum chemical calculations. Only noisy signals of potential dimers were observed during experiments on the ozonolysis of the monoterpene α-pinene, while a few small signals of dimeric compounds were detected during the ozonolysis of cyclohexene. During the latter experiments, we also tested varying the pressures and electric fields in the ionization region of the Vocus PTR-TOF, finding that only small improvements were possible in the relative dimer contributions. Calculations for model ROOR and ROOH systems showed that most of these peroxides should fragment partially following protonation. With inclusion of additional energy from the ion-molecule collisions driven by the electric fields in the ionization source, computational results suggest substantial or nearly complete fragmentation of dimers. Our study thus suggests that while the improved versions of PTR-based mass spectrometers are very powerful tools for measuring hydrocarbons and their moderately oxidized products, other types of CIMS are likely more suitable for the detection of ROOR and ROOH species.

Diterpenes (C20H32) are biogenically emitted volatile compounds that only recently have been observed in ambient air. They are expected to be highly reactive, and their oxidation is likely to form condensable vapors. However, until now, no studies have investigated gas-phase diterpene oxidation. In this paper, we explored the ozonolysis of a diterpene, ent-kaurene, in a simulation chamber. Using state-of-the-art mass spectrometry, we characterized diterpene oxidation products for the first time, and we identified several products with varying oxidation levels, including highly oxygenated organic molecules (HOM) monomers and dimers. The most abundant monomers measured using a nitrate chemical ionization mass spectrometer were C19H28O8 and C20H30O5, and dimers were C38H60O6 and C39H62O6. The exact molar yield of HOM from kaurene ozonolysis was hard to quantify due to uncertainties in both the kaurene and HOM concentrations, but our best estimate was a few percent, which is similar to values reported earlier for many monoterpenes. We also monitored the decrease of the gas-phase oxidation products in response to an increased condensation sink in the chamber to deduce their affinity to condense. The oxygen content was a critical parameter affecting the volatility of products, with 4–5 O-atoms needed for the main monomeric species to condense. Finally, we report on the observed fragmentation and clustering patterns of kaurene in a Vocus proton transfer reaction time-of-flight mass spectrometer. Our findings highlight similarities and differences between diterpenes and smaller terpenes during their atmospheric oxidation, but more studies on different diterpenes are needed for a broader view of their role in atmospheric chemistry.

Oxygenated organic molecules (OOMs) are the crucial intermediates linking volatile organic compounds (VOCs) to secondary organic aerosol (SOA) in the atmosphere, but understandings on the characteristics of OOMs and their formations from VOCs are very limited. Ambient observations of OOMs using recently developed mass spectrometry techniques are still limited, especially in polluted urban atmosphere where VOCs and oxidants are extremely variable and complex. Here, we investigate OOMs, measured by a nitrate-ion-based chemical ionization mass spectrometer at Nanjing in eastern China, through performing positive matrix factorization on binned mass spectra (binPMF). The binPMF analysis reveals three factors about anthropogenic VOCs (AVOCs) daytime chemistry, three isoprene-related factors, three factors about biogenic VOCs (BVOCs) nighttime chemistry, and three factors about nitrated phenols. All factors are influenced by NOx in different ways and to different extents. Over 1000 non-nitro molecules have been identified and then reconstructed from the selected solution of binPMF, and about 72 % of the total signals are contributed by nitrogen-containing OOMs, mostly regarded as organic nitrates formed through peroxy radicals terminated by nitric oxide or nitrate-radical-initiated oxidations. Moreover, multi-nitrates account for about 24 % of the total signals, indicating the significant presence of multiple generations, especially for isoprene (e.g., C5H10O8N2 and C5H9O10N3). Additionally, the distribution of OOMs concentration on carbon number confirm their precursors driven by AVOCs mixed with enhanced BVOCs during summer. Our results highlight the decisive role of NOx on OOMs formation in densely populated areas, and encourage more studies on the dramatic interactions between anthropogenic and biogenic emissions.

The formation of alkyl nitrates in various oxidation processes taking place throughout the diel cycle can represent an important sink of reactive nitrogen and mechanism for chain termination in atmospheric photo-oxidation cycles. The low-volatility alkyl nitrates (ANs) formed from biogenic volatile organic compounds (BVOCs), especially terpenoids, enhance rates of production and growth of secondary organic aerosol. Measurements of the NO3 reactivity and the mixing ratio of total alkyl nitrates (ΣANs) in the Finnish boreal forest enabled assessment of the relative importance of NO3-, O3- and OH-initiated formation of alkyl nitrates from BVOCs in this environment. The high reactivity of the forest air towards NO3 resulted in reactions of the nitrate radical, with terpenes contributing substantially to formation of ANs not only during the night but also during daytime. Overall, night-time reactions of NO3 accounted for 49 % of the local production rate of ANs, with contributions of 21 %, 18 % and 12 % for NO3, OH and O3 during the day. The lifetimes of the gas-phase ANs formed in this environment were on the order of 2 h due to efficient uptake to aerosol (and dry deposition), resulting in the transfer of reactive nitrogen from anthropogenic sources to the forest ecosystem.

Secondary organic aerosol (SOA) is known to impact both climate and air quality, yet molecular-level composition measurements remain challenging, hampering our understanding of SOA formation and evolution. Here, we reveal the importance of underestimated reaction pathways for the (trans)formation of SOA from monoterpenes, one of the largest SOA precursors globally. Utilizing mass spectrometric techniques to achieve a comprehensive characterization of molecular-level changes in the SOA, we were able to link the appearance of high-molecular weight (HMW) organic molecules to the concentration and level of neutralization of particulate sulfate. Interestingly, this oligomerization coincided with a decrease of highly oxygenated molecules (HOMs). Our findings highlight the role of particle-phase processing, and the underestimated importance of sulfate aerosol for monoterpene-SOA formation. The observations of these processes directly in the atmosphere reveal the need to account for the formation of HMW oligomers to fully understand the physicochemical properties of organic aerosol. Sulfate aerosols produced by industrial activities provide a key substrate for the formation of secondary organic aerosols (SOA) hundreds of km away. An international research group led by Matthieu Riva, now at the Universite de Lyon, applied detailed field observations and atmospheric transport modeling to show that SOA are produced when sulfate aerosols interact with monoterpenes — a volatile organic compound emitted by forests. Specifically, along the atmospheric transport pathway from the Russian pollution source to the research station in Finland, oxidized monoterpenes condensed onto sulfate particles, forming SOA. The team used laboratory experiments to confirm a powerful influence of sulfate levels on SOA formation. The research extends prior work showing similar pathways for isoprene-related SOA formation, and cements the importance of SOA formation through multiphase chemistry across of range of biogenically-derived atmospheric compounds.

Secondary organic aerosol contributes to the atmospheric particle burden with implications for air quality and climate. Biogenic volatile organic compounds such as terpenoids emitted from plants are important secondary organic aerosol precursors with isoprene dominating the emissions of biogenic volatile organic compounds globally. However, the particle mass from isoprene oxidation is generally modest compared to that of other terpenoids. Here we show that isoprene, carbon monoxide and methane can each suppress the instantaneous mass and the overall mass yield derived from monoterpenes in mixtures of atmospheric vapours. We find that isoprene ‘scavenges’ hydroxyl radicals, preventing their reaction with monoterpenes, and the resulting isoprene peroxy radicals scavenge highly oxygenated monoterpene products. These effects reduce the yield of low-volatility products that would otherwise form secondary organic aerosol. Global model calculations indicate that oxidant and product scavenging can operate effectively in the real atmosphere. Thus highly reactive compounds (such as isoprene) that produce a modest amount of aerosol are not necessarily net producers of secondary organic particle mass and their oxidation in mixtures of atmospheric vapours can suppress both particle number and mass of secondary organic aerosol. We suggest that formation mechanisms of secondary organic aerosol in the atmosphere need to be considered more realistically, accounting for mechanistic interactions between the products of oxidizing precursor molecules (as is recognized to be necessary when modelling ozone production). Adding reactive gases such as isoprene to mixtures lowers the production of secondary organic aerosol in the atmosphere, thus reducing the atmospheric particulate burden, with implications for human health and climate.

Biogenic secondary organic aerosol (BSOA) constitutes a major fraction of aerosol over boreal forests. As the emissions of BSOA precursors are temperature dependent, changes in temperature have potentially important implications on regional aerosol radiative forcing. Here, we have used long-term aerosol composition and temperature data measurements from a boreal forest site together with remote sensing observations of aerosol and cloud properties to investigate the effect of increasing temperature on organic aerosol mass loadings, and further on aerosol direct and indirect radiative effects. The analysis was based on 7 years of measurements done at Hyytiälä, Southern Finland, and they cover the summer months (July-August) between 2012-2018. We limited the analyses to these summer months to isolate the temperature dependence of the organic mass loadings from the seasonal effects arising from the vegetation growth cycle. Our analysis showed that organic aerosol loadings and cloud condensation nuclei concentrations increased in concert with surface temperature. Furthermore, we found that cloud reflectivity increased when the organic aerosol loadings increased. This research presents the first direct observational evidence on the effect of BSOA on cloud properties and their climatic significance.

Atmospheric plastic pollution is now a global problem. Microplastics (MP) have been detected in urban atmospheres as well as in remote and pristine environments, showing that suspension, deposition and aeolian transport of MP should be included and considered as a major transport pathway in the plastic life cycle. Due to the limitations in sampling and instrumental methodology, little is known about MP and nanoplastics (NP) with sizes lower than 50 µm, which is the current limit for FT-IR and Raman microscopy. In our recent work [Bianco et al. 2020], we describe how NP could be transported for longer distances than MP, making them globally present and potentially more concentrated than MP. We highlight that it is crucial to explore new methodologies to collect and analyse NP.Small MPs can be detected by fluorescence spectroscopy: for example, particles can be efficiently stained using Nile Red, as described by Erni-Cassola et al. [2017]. This hydrophobic dye shows fluorescence in green and yellow range of the electromagnetic spectrum and can be easily detected also at low concentration. We are developing a new method, based on this principle, to detect MPs in natural matrices. These are, for instance, surface and atmospheric waters, containing dissolved organic matter and suspended organic particles. Preliminary results on polyethylene, polystyrene and polyvinylchloride are promising for particles in the range 1-25 µm suspended in MilliQ water. We are currently testing the method on river water and snow. Bianco, A.; Passananti, M. Atmospheric Micro and Nanoplastics: An Enormous Microscopic Problem. Sustainability 2020, 12, 7327.Erni-Cassola, G.; Gibson, M.; Thompson, R.; Christie-Oleza, J. Lost, but Found with Nile Red: A Novel Method for Detecting and Quantifying Small Microplastics (1 mm to 20 μm) in Environmental Samples. Environ. Sci. Technol. 2017, 51, 23, 13641–13648

Efficient autoxidation of organic compounds typically requires that they possess double bonds or oxygen-containing moieties, which is why alkanes were thought to contribute little to atmospheric organic aerosol formation. Here, mass spectrometry shows significant autoxidation of alkanes under both atmospheric and combustion conditions. Oxidation chemistry controls both combustion processes and the atmospheric transformation of volatile emissions. In combustion engines, radical species undergo isomerization reactions that allow fast addition of O-2. This chain reaction, termed autoxidation, is enabled by high engine temperatures, but has recently been also identified as an important source for highly oxygenated species in the atmosphere, forming organic aerosol. Conventional knowledge suggests that atmospheric autoxidation requires suitable structural features, like double bonds or oxygen-containing moieties, in the precursors. With neither of these functionalities, alkanes, the primary fuel type in combustion engines and an important class of urban trace gases, are thought to have minor susceptibility to extensive autoxidation. Here, utilizing state-of-the-art mass spectrometry, measuring both radicals and oxidation products, we show that alkanes undergo autoxidation much more efficiently than previously thought, both under atmospheric and combustion conditions. Even at high concentrations of NOX, which typically rapidly terminates autoxidation in urban areas, the studied C-6-C-10 alkanes produce considerable amounts of highly oxygenated products that can contribute to urban organic aerosol. The results of this inter-disciplinary effort provide crucial information on oxidation processes in both combustion engines and the atmosphere, with direct implications for engine efficiency and urban air quality.

Organic peroxy radicals (RO2) play a pivotal role in the degradation of hydrocarbons. The autoxidation of atmospheric RO2 radicals produces highly oxygenated organic molecules (HOMs), including low-volatility ROOR dimers formed by bimolecular RO2 + RO2 reactions. HOMs can initiate and greatly contribute to the formation and growth of atmospheric particles. As a result, HOMs have far-reaching health and climate implications. Nevertheless, the structures and formation mechanism of RO2 radicals and HOMs remain elusive. Here, we present the in-situ characterization of RO2 and dimer structure in the gas-phase, using online tandem mass spectrometry analyses. In this study, we constrain the structures and formation pathway of several HOM-RO2 radicals and dimers produced from monoterpene ozonolysis, a prominent atmospheric oxidation process. In addition to providing insights into atmospheric HOM chemistry, this study debuts online tandem MS analyses as a unique approach for the chemical characterization of reactive compounds, e.g., organic radicals., Organic peroxy radicals play a pivotal role in producing highly oxygenated organic molecules but the formation mechanisms remain elusive. Here, the authors show in-situ characterization of peroxy radicals and dimer structures in the gas-phase, using online tandem mass spectrometry analyses.

We compared observations of aerosol particle formation and growth in different parts of the planetary boundary layer at two different environments that have frequent new particle formation (NPF) events. In summer 2012 we had a campaign in Po Valley, Italy (urban background), and in spring 2013 a similar campaign took place in Hyytiala, Finland (rural background). Our study consists of three case studies of airborne and ground-based measurements of ion and particle size distribution from similar to 1 nm. The airborne measurements were performed using a Zeppelin inside the boundary layer up to 1000m altitude. Our observations show the onset of regional NPF and the subsequent growth of the aerosol particles happening almost uniformly inside the mixed layer (ML) in both locations. However, in Hyytiala we noticed local enhancement in the intensity of NPF caused by mesoscale boundary layer (BL) dynamics. Additionally, our observations indicate that in Hyytiala NPF was probably also taking place above the ML. In Po Valley we observed NPF that was limited to a specific air mass.

11 pags., 4 figs., New particle formation in the Arctic atmosphere is an important source of aerosol particles. Understanding the processes of Arctic secondary aerosol formation is crucial due to their significant impact on cloud properties and therefore Arctic amplification. We observed the molecular formation of new particles from low-volatility vapors at two Arctic sites with differing surroundings. In Svalbard, sulfuric acid (SA) and methane sulfonic acid (MSA) contribute to the formation of secondary aerosol and to some extent to cloud condensation nuclei (CCN). This occurs via ion-induced nucleation of SA and NH and subsequent growth by mainly SA and MSA condensation during springtime and highly oxygenated organic molecules during summertime. By contrast, in an ice-covered region around Villum, we observed new particle formation driven by iodic acid but its concentration was insufficient to grow nucleated particles to CCN sizes. Our results provide new insight about sources and precursors of Arctic secondary aerosol particles., The authors acknowledge European Research Council (GASPARCON, Grant no. 714621 and COALA, Grant no. 638703), Academy of Finland (Project nos. 296628, 306853, 317380, 316114, and 320094), INTERACT, European Regional Development Fund (project MOBTT42), Austrian Science Fund (FWF, Project J3951-N36), the European Union's Horizon 2020 Research and Innovation Program (Grant no. 689443) via project iCUPE (Integrative and Comprehensive Understanding on Polar Environments) and Project ERC-2016- COG 726349 CLIMAHAL, National Research Foundation (NRF) of the Ministry of Science, ICT and Future Planning (NRF-2018R1A2A1A19019281), Knut-and-Alice-Wallenberg Foundation within the Arctic Climate Across Scales (Project No. \,2016.0024), the Swedish EPA's (Naturvårdsverket) Environmental monitoring program (Miljöövervakning), the Swedish Research Council FORMAS (Project "Interplay between water, clouds and Aerosols in the Arctic," \# 2016-01427), Climate Change Tower – Integrated Project of the National Research Council of Italy and the National Interest Project by the Italian Minister of Education, University and Research (PRIN2007 and PRIN2009). The authors thank Department of Earth System Sciences and Technologies for the Environment, Department of Earth Sciences and Technology of the Environment of CNR and the doctoral program in atmospheric sciences at the University of Helsinki for financial support. Aarhus University acknowledge financial support from Danish Ministry of Environment and food and Ministry of Climate, Energy and Utilities by means of DANCEA.

The Station for Measuring Ecosystem–Atmosphere Relations (SMEAR) II, located within the boreal forest of Finland, is a unique station in the world due to the wide range of long-term measurements tracking the Earth–atmosphere interface. In this study, we characterize the composition of organic aerosol (OA) at SMEAR II by quantifying its driving constituents. We utilize a multi-year data set of OA mass spectra measured in situ with an Aerosol Chemical Speciation Monitor (ACSM) at the station. To our knowledge, this mass spectral time series is the longest of its kind published to date. Similarly to other previously reported efforts in OA source apportionment from multi-seasonal or multi-annual data sets, we approached the OA characterization challenge through positive matrix factorization (PMF) using a rolling window approach. However, the existing methods for extracting minor OA components were found to be insufficient for our rather remote site. To overcome this issue, we tested a new statistical analysis framework. This included unsupervised feature extraction and classification stages to explore a large number of unconstrained PMF runs conducted on the measured OA mass spectra. Anchored by these results, we finally constructed a relaxed chemical mass balance (CMB) run that resolved different OA components from our observations. The presented combination of statistical tools provided a data-driven analysis methodology, which in our case achieved robust solutions with minimal subjectivity. Following the extensive statistical analyses, we were able to divide the 2012–2019 SMEAR II OA data (mass concentration interquartile range (IQR): 0.7, 1.3, and 2.6 µg m−3) into three sub-categories – low-volatility oxygenated OA (LV-OOA), semi-volatile oxygenated OA (SV-OOA), and primary OA (POA) – proving that the tested methodology was able to provide results consistent with literature. LV-OOA was the most dominant OA type (organic mass fraction IQR: 49 %, 62 %, and 73 %). The seasonal cycle of LV-OOA was bimodal, with peaks both in summer and in February. We associated the wintertime LV-OOA with anthropogenic sources and assumed biogenic influence in LV-OOA formation in summer. Through a brief trajectory analysis, we estimated summertime natural LV-OOA formation of tens of ng m−3 h−1 over the boreal forest. SV-OOA was the second highest contributor to OA mass (organic mass fraction IQR: 19 %, 31 %, and 43 %). Due to SV-OOA's clear peak in summer, we estimate biogenic processes as the main drivers in its formation. Unlike for LV-OOA, the highest SV-OOA concentrations were detected in stable summertime nocturnal surface layers. Two nearby sawmills also played a significant role in SV-OOA production as also exemplified by previous studies at SMEAR II. POA, taken as a mix of two different OA types reported previously, hydrocarbon-like OA (HOA) and biomass burning OA (BBOA), made up a minimal OA mass fraction (IQR: 2 %, 6 %, and 13 %). Notably, the quantification of POA at SMEAR II using ACSM data was not possible following existing rolling PMF methodologies. Both POA organic mass fraction and mass concentration peaked in winter. Its appearance at SMEAR II was linked to strong southerly winds. Similar wind direction and speed dependence was not observed among other OA types. The high wind speeds probably enabled the POA transport to SMEAR II from faraway sources in a relatively fresh state. In the event of slower wind speeds, POA likely evaporated and/or aged into oxidized organic aerosol before detection. The POA organic mass fraction was significantly lower than reported by aerosol mass spectrometer (AMS) measurements 2 to 4 years prior to the ACSM measurements. While the co-located long-term measurements of black carbon supported the hypothesis of higher POA loadings prior to year 2012, it is also possible that short-term (POA) pollution plumes were averaged out due to the slow time resolution of the ACSM combined with the further 3 h data averaging needed to ensure good signal-to-noise ratios (SNRs). Despite the length of the ACSM data set, we did not focus on quantifying long-term trends of POA (nor other components) due to the high sensitivity of OA composition to meteorological anomalies, the occurrence of which is likely not normally distributed over the 8-year measurement period. Due to the unique and realistic seasonal cycles and meteorology dependences of the independent OA subtypes complemented by the reasonably low degree of unexplained OA variability, we believe that the presented data analysis approach performs well. Therefore, we hope that these results encourage also other researchers possessing several-year-long time series of similar data to tackle the data analysis via similar semi- or unsupervised machine-learning approaches. This way the presented method could be further optimized and its usability explored and evaluated also in other environments., Atmospheric Chemistry and Physics, 21 (13), ISSN:1680-7375, ISSN:1680-7367

Cyclohexene (C6H10) is commonly used as a proxy for biogenic monoterpenes, when studying their oxidation mechanisms and secondary organic aerosol (SOA) formation. The ozonolysis of cyclohexene has been shown to be effective at producing highly oxygenated organic molecules (HOM), a group of molecules known to be important in the formation of SOA. Here, we provide an in depth look at how, on a molecular level, the HOM formation and fate changed with perturbations from NOx and seed particles. HOM were produced in a chamber from cyclohexene ozonolysis, and measured with a chemical ionisation mass spectrometer (CIMS) using nitrate (NO3−) as reagent ion. As high-resolution CIMS instruments provide mass spectra with numerous ion signals and a wealth of information that can be hard to manage, we employed a primarily statistical approach for the data analysis. To utilise as many individual HOM signals as possible, each compound was assigned a parameter describing the quality of the observed signal. These parameters were then used as weights or to determine the inclusion of a given signal in further analyses. Under unperturbed ozonolysis conditions, known HOM peaks were observed in the chamber, including C6H8O9 as the largest HOM signal, and C12H20O9 as the largest dimer product. With the addition of nitric oxide (NO) into the chamber, the spectrum changed considerably, as expected. Dimer product signals decreased overall, but an increase in dimers with nitrate functionalities was seen, as a result of NO3 radical oxidation. The response of monomer signals to NO addition varied, and while nitrate-containing monomers increased, non-nitrate signals either increased or decreased, depending on the individual molecules. The addition of seed aerosol increased the condensation sink, which markedly decreased the signals of all low-volatility compounds. Larger molecules were seen to have a higher affinity for condensation, but a more detailed analysis showed that the uptake was controlled mainly by the number of oxygen atoms in each molecule. All non-nitrate compounds with at least 7 oxygen atoms were observed to condense onto the seed aerosol at close to equal rates. Nitrates required higher mass and higher oxygen content to condense at similar rates as the non-nitrate HOM. A comparison to experiments with alpha-pinene reported earlier, showed quite a similar relationship between elemental composition and volatility, although products from alpha-pinene ozonolysis appeared to require slightly higher oxygen numbers for the same decrease in volatility. In addition, two models developed for predicting volatilities of volatile organic compound (VOC) oxidation products were tested on the ozonolysis products of cyclohexene.

Aromatic hydrocarbons are a class of volatile organic compounds associated with anthropogenic activity and make up a significant fraction of urban VOC emissions that contribute to the formation of secondary organic aerosol (SOA). Benzene is one of the most abundant species emitted from vehicles, biomass burning and industry. An iodide time of flight chemical ionisation mass spectrometer (ToF-CIMS) and nitrate ToF-CIMS were deployed at the Jülich plant chamber as part of a series of experiments examining benzene oxidation by OH under high and low NOx conditions, where a range of organic oxidation products were detected. The nitrate scheme detects many oxidation products with high masses ranging from intermediate volatile organic compounds (IVOC) to extremely low volatile organic compounds (ELVOC), including C12 dimers. In comparison, very few species with C≥6 and O≥8 were detected with the iodide scheme, which detected many more IVOC and semi volatile organic compounds (SVOC) but very few ELVOC and low volatile organic compounds (LVOC). 132 and 195 CHO and CHON oxidation products are detected by the iodide ToF-CIMS in the low and high NOx experiments respectively. Ring breaking products make up the dominant fraction of detected signal (89–91 %). 21 and 26 of the products listed in the master chemical mechanism (MCM) were detected and account for 6.4–7.3 % of total signal. The time series of highly oxidised (O≥6) and ring retaining oxidation products (C6 and double bond equivalent = 4) equilibrate quickly characterised by a square form profile, compared to MCM and ring breaking products which increase throughout oxidation exhibiting saw tooth profiles. Under low NOx conditions, all CHO formulae attributed to radical termination reactions of 1st generation benzene products and 1st generation autoxidation products are observed, and one exclusively 2nd generation autoxidation product is also measured (C6H8O8). Several N containing species that are either 1st generation benzene products or 1st generation autoxidation products are also observed under high NOx conditions. Hierarchical cluster analysis finds four cluster of which two describe photo-oxidation. Cluster 2 shows a negative dependency on the NO2/NOx ratio indicating it is sensitive to NO concentration thus likely to contain NO addition products and alkoxy derived termination products. This cluster has the highest average carbon oxidation state (OSc) and the lowest average carbon number and where nitrogen is present in cluster member, the oxygen number is even, as expected for alkoxy derived products. In contrast, cluster 1 shows no dependency on the NO2/NOx ratio and so is likely to contain more NO2 addition and peroxy derived termination products. This cluster contains less fragmented species, as the average carbon number is higher and OSc lower than cluster 2, and more species with an odd number of oxygen atoms. This suggests clustering of time series which have features pertaining to distinct chemical regimes e.g. NO2/NOx perturbations, coupled with a priori knowledge, can provide insight into identification of potential functionality.