Search

Changes in the structure, phase composition, chemical composition, Vickers microhardness, and contact modulus of elasticity of a high-strength titanium α + β-alloy of the VST2 martensitic class during quenching after heating in the 700 – 1000°Ñ range were studied using the methods of optical microscopy, XRD phase analysis, microindentation, and thermodynamic calculations in ThermoCalc. The experimental data were in good agreement with the results of thermodynamic calculations. Arelationship between changes in the microhardness and contact modulus of elasticity of VST2 alloy, quenched from 700 – 1000°C, and the structure and phase composition of the alloy during quenching was established. [ABSTRACT FROM AUTHOR]

The efficient characterization of material properties of porous multi-phase sintered steels by instrumental indentation is still an open question. To the authors' knowledge, so far only a characterization of single-phase porous sintered steel by nanoindenation has been reported in literature. This paper for the first time offers a study about the applicability of microindentation techniques for characterizing the matrix material in a multi-phase sintered steel. This preliminary study is motivated by the relatively wide availability of necessary equipment, and simplicity of material identification procedures. Herein, a dual-phase ferrite/bainite Astaloy steel with 9% porosity is studied. Various commonly used methods for the reconstruction of stress–strain curves from microindentation data are considered, whereby both Vickers and spherical tips are used. In addition, some homogeneous solid materials are investigated to better asses the performance of applied identification procedures. Two approaches for the mesoscale identification of the considered sintered steel are attempted. The first one is based on the identification of individual material phases, while in the other one the homogenization of the metallic matrix is adopted. To assess the reliability of obtained parameters, the direct numerical simulation of representative volume elements of realistic steel microstructure subjected to uniaxial tension is conducted. Numerical results are compared with the data from the macroscopic uniaxial tensile test. The obtained results indicate that microindentation is adequate for the identification of elastic properties of individual material phases, but results for local plastic parameters are largely inconclusive and a further analysis is needed, focusing on applying smaller forces and investigating the influence of pores on identification results. Nevertheless, it seems that macroscopic stress–strain curves could be captured more accurately by the methodology based on the matrix homogenization if relatively large indentation forces are applied. [ABSTRACT FROM AUTHOR]

In the present work, we studied the dry tribological behaviour of a 100Cr6 steel, the spherical surface of which was texturized with microindentation. The purpose of adopting a mechanical indentation technique on a non-planar surface was to simultaneously evaluate the effectiveness of adopting a fast, deformation-based technique for improving the contact tribological properties. Specifically, dimples were created using an automatic microhardness tester equipped with a Vickers indenter, setting a load of 0.5 N. Friction tests were performed at different speeds considering textured surfaces with two different void ratios (VRs). Textured and untextured surfaces were tested using a ball-on-disc tribometer. In addition, the effect of dimple size was evaluated by producing Vickers indented surfaces at a load of 5 N per each indentation, while keeping the VR values unchanged and testing the frictional properties of such surfaces at a fixed speed of 4.18 mm/s. Textured surfaces were deeply investigated to motivate the improvement of tribological properties. Notably, compared to the untextured samples, the microindented samples exhibited a much lower coefficient of friction (COF), with a friction reduction compared to the untextured case ranging from 45 to 65%, depending on the VR values. The adoption of large dimples allowed the reduction of the COF, already at smaller VR value but, in such a case, the presence of bulges at the edge of the dimple worsens the wear resistance of the counter surface. In addition to reducing the contact area and the capability to trap any debris in the dimples, the local measurement of strength allowed to clarify that the friction reduction is also determined by the work hardening effect produced by the microindentation texturing. Considering the significant improvements recorded in terms of COF and the high ability to indent even non-planar surfaces, the proposed approach can be considered very promising and, therefore, industrially applicable (e.g. using a specifically designed multi-indenter tool) to affect the friction behaviour of components, even locally, during both their use and their production. [ABSTRACT FROM AUTHOR]

The surface of the AlSi7Mg alloy was alloyed with CoNiCrW powder using a continuous wave fiber laser with a wavelength of 1.07 μm. The thickness of the alloyed layer is up to 4 mm. Its microstructure is radically different from the microstructure of the AlSi7Mg alloy. The basis of the microstructure of the alloyed layer is an α-solid solution based on aluminum, eutectic α + Si, and (Co,Ni)Al. The strengthening phases are aluminum oxides Al2O3, borides of the CrB type, and chromium carbides of various compositions. The alloyed layer is characterized by an average microhardness of 700 HV, an increased ability to resist elastoplastic deformation, and an increased wear resistance during abrasive wear tests. During wear tests under dry sliding friction conditions on a steel (0.2% C) counterbody, the alloyed layer is destroyed, which leads to an increase in mass loss during operation in such conditions. [ABSTRACT FROM AUTHOR]

The field stress of the shale affects the proppant embedment, fracture conductivity, well production rate, and ultimately the recovery of hydrocarbons from reservoir formations. This paper presents, for the first time, an experimental study investigating the mechanical characteristics of a shale under confining pressures that simulate the in situ stress state in deep reservoirs. Bidirectional but equal confining pressures were applied to the shale sample to replicate its field stress state. Microindentation tests were conducted to assess the alterations of mechanical properties resulting from the application of confining pressures. The results demonstrate a significant increase in Young's modulus, hardness, and fracture toughness for the samples subjected to confining pressure. Considering the effect of confining pressure, the decrease in proppant embedment is proportional to Young's modulus of the shale. For larger-sized proppants (e.g., D = 2.50 mm), the influence of confining pressure on fracture conductivity is relatively minor. However, when smaller-sized proppants (e.g., D = 1.00 mm) are used, particularly in scenarios involving shale debris swelling due to prolonged interaction with fracturing fluid, there is a noticeable improvement in fracture conductivity. Importantly, previous computational models have tended to overestimate proppant embedment depth while underestimating fracture conductivity. The findings from this study contribute to advancing the understanding of shale's mechanical characteristics under in situ reservoir conditions and support the optimization of proppant embedment and fracture conductivity calculation models for the efficient extraction of shale gas. [ABSTRACT FROM AUTHOR]

The lab-made ferrite-aluminium layered double oxide (Fe/Al LDO) nanoparticles were used as reinforcement in the production of copper matrix composite coatings via the electrodeposition route in this study. The Cu coatings electrodeposited galvanostatically without and with low concentrations of Fe/Al LDO nanoparticles were characterized by SEM (morphology), AFM (topography and roughness), XRD (phase composition and texture), Vickers microindentation (hardness), and the static sessile drop method (wettability). All Cu coatings were fine-grained and microcrystalline with a (220) preferred orientation, with a tendency to increase the grain size, the roughness, and this degree of the preferred orientation with increasing the coating thickness. The cross-section analysis of coatings electrodeposited with Fe/Al LDO nanoparticles showed their uniform distribution throughout the coating. Hardness analysis of Cu coatings performed by application of the Chicot-Lesage (C-L) composite hardness model showed that Fe/Al LDO nanoparticles added to the electrolyte caused a change of the composite system from "soft film on hard cathode" into "hard film on soft cathode" type, confirming the successful incorporation of the nanoparticles in the coatings. The increase in roughness had a crucial effect on the wettability of the coatings, causing a change from hydrophilic reinforcement-free coatings to hydrophobic coatings obtained with incorporated Fe/Al LDO nanoparticles. [ABSTRACT FROM AUTHOR]

The aim of this study is to investigate the influence of cross-linking and reinforcements in gelatin on the physico-mechanical properties of obtained composites. The gelatin-based composites cross-linked with citric acid (CA) were prepared: gelatin type B (GB) and β-tricalcium phosphate (β-TCP) and novel hybrid composite GB with β-TCP and hydroxyapatite (HAp) particles, and their structure, thermal, and mechanical properties were compared with pure gelatin B samples. FTIR analysis revealed that no chemical interaction between the reinforcements and gelatin matrix was established during the processing of hybrid composites by the solution casting method, proving the particles had no influence on GB cross-linking. The morphological investigation of hybrid composites revealed that cross-linking with CA improved the dispersion of particles, which further led to an increase in mechanical performance. The microindentation test showed that the hardness value was increased by up to 449%, which shows the high potential of β-TCP and HAp particle reinforcement combined with CA as a cross-linking agent. Furthermore, the reduced modulus of elasticity was increased by up to 288%. Results of the MTT assay on L929 cells have revealed that the hybrid composite GB-TCP-HA-CA was not cytotoxic. These results showed that GB cross-linked with CA and reinforced with different calcium phosphates presents a valuable novel material with potential applications in dentistry. [ABSTRACT FROM AUTHOR]

A calcium phosphate extracted from fish bones (CaP-N) was evaluated for enamel remineralization and dentinal tubules occlusion. CaP-N was characterized by assessing morphology by SEM, crystallinity by PXRD, and composition by ICP-OES. CaP-N morphology, crystallinity, ion release, and pH changes over time in neutral and acidic solutions were studied. CaP-N was then tested to assess remineralization and dentinal tubules occlusion on demineralized human enamel and dentin specimens (n = 6). Synthetic calcium phosphate in form of stoichiometric hydroxyapatite nanoparticles (CaP-S) and tap water were positive and negative controls, respectively. After treatment (brush every 12 h for 5d and storage in Dulbecco's modified PBS), specimens' morphology and surface composition were assessed (by SEM-EDS), while the viscoelastic behavior was evaluated with microindentation and DMA. CaP-N consisted of rounded microparticles (200 nm - 1 µm) composed of 33 wt% hydroxyapatite and 67 wt% β-tricalcium phosphate. In acidic solution, CaP-N released calcium and phosphate ions thanks to the preferential β-tricalcium phosphate phase dissolution. Enamel remineralization was induced by CaP-N comparably to CaP-S, while CaP-N exhibited a superior dentinal tubule occlusion than CaP-S, forming mineral plugs and depositing new nanoparticles onto demineralized collagen. This behavior was attributed to its bigger particle size and increased solubility. DMA depth profiling and SEM showed an excellent interaction between the newly formed mineralized structures and the pristine tissue, particularly at the exposed collagen fibrils. CaP-N demonstrated very good remineralizing and occlusive activity in vitro , comparable to CaP-S, thus could be a promising circular economy alternative therapeutic agent for dentistry. • Biphasic hydroxyapatite/β-tricalcium phosphate material was extracted by thermal treatment of fish bones. • The material remineralized enamel and dentin and induced complete dentinal tubule occlusion. • Mechanical connection between the newly formed mineralized structures and pristine tissue was excellent. • The efficacy of the material was comparable to synthetic stoichiometric hydroxyapatite nanoparticles. [ABSTRACT FROM AUTHOR]

The behavior of a structure under the influence of external factors is determined by three key groups of parameters the metal composition (chemical, structural, and deformation). Obtaining information about these parameters directly on the structure will effectively solve the problem of assessing its actual technical condition. The problem of nondestructive evaluation of the chemical composition of metal is solved using portable spectrometers. A Microlab-Z2 diagnostic complex has been developed to evaluate the other two groups of parameters. It has two functional blocks. The surface preparation unit ensures that the surface of the construction site has a roughness, flatness, and level of applied mechanical hardening corresponding to the laboratory preparation of metallographic specimens. The research unit is a platform on which a metallographic microscope and a portable microhardness tester are installed. It allows metallographic research with magnification up to ×1000, surface microindentation, measurement of microhardness values at load of 0–200 gf, and optical study of the morphology of imprints in any spatial position. The reliability of the data obtained by the Microlab-Z2 diagnostic complex has been confirmed during comparative tests with stationary equipment. An assessment of structure parameters and contamination of metal with nonmetallic inclusions, assessment of the degree of hardening and embrittlement of metal, and detection of aging processes can be performed with the help of the developed device. The use of the Microlab-Z2 diagnostic complex for operational nondestructive evaluation of structural and deformation parameters of metal structures will allow reaching a qualitatively different level of efficiency in performing production and acceptance testing of manufactured products, assessing the maintainability of defects, planning repairs and other compensating measures, and industrial safety expertise. [ABSTRACT FROM AUTHOR]

The 3D printing of composite materials especially, nanocomposites, is an essential step in exploring new perspectives for the applications of organic matrix composite materials for industrial applications. In this work, the effect of ceramic nanofillers on the mechanical properties of a thermoplastic matrix is studied using different wt% of nanofillers (AEROSIL). The results showed that the increase in the wt% of AEROSIL resulted in an increase in the mechanical properties in terms of hardness, stiffness, ductility, and tensile strength. Moreover, these samples were 3D printed and were compared with the samples prepared by conventional injection moulding. The comparison characterized the influence of the manufacturing method on the mechanical performance of materials. Although there was very little behavior difference in both samples, the 3D-printed samples showed a weight reduction. This has broadened the possible applications of this material and technique in areas where weight is of utmost significance. [ABSTRACT FROM AUTHOR]

This article discusses the micromechanical properties and true microhardness determination of nanostructured tribological coatings (NTCs) based on a multilayered alternating nitride/carbonitride bilayer substructure for transition metals. The constituent nitride/carbonitride bilayers in the superlattice structure of the NTC were alloyed with refractory metals, denoted as Me = Me1 or Me2= Cr, Hf, Nb, W, and Zr. The resulting NTC coatings were deposited onto 100Cr6 steel substrates using an advanced physical vapor deposition (PVD) technique, referred to here as high-power ion-plasma magnetron sputtering (HiPIPMS). The comprising crystalline nanometer-scale TiAlSiMe1-N/TiMe2-CN nanoparticles strengthened by Me additives significantly increased the NTC microhardness to over 3200 HV. The primary focus of this research was to determine the true microhardness of the NTC film samples. The apparent microhardness (Ha) of the film/substrate system for various NTC samples was measured during microindentation testing using the Vickers method. Nine NTC samples were tested, each generating a corresponding microindentation dataset containing between 430 and 640 imprints, depending on the specific NTC sample. These datasets were analyzed using three distinct empirical approaches: (i) the inverse power-law model (IPL-Model), (ii) the sigmoid-like decay model (SLD-Model), and (iii) the error function model (ERF-Model). The observed solid correlation between the proposed models and experiments suggests that the true microhardness estimates (Hf) obtained through the empirical mathematical modeling approach are reliable. [ABSTRACT FROM AUTHOR]

The fibrocartilaginous tendon enthesis, i.e. the site where a tendon is attached to bone through a fibrocartilaginous tissue, is considered as a functionally graded interface. However, at local scale, a very limited number of studies have characterized micromechanical properties of this transitional tissue. The first goal of this work was to characterize the micromechanical properties of the mineralized part of the healthy Achilles tendon enthesis (ATE) through microindentation testing and to assess the degree of mineralization and of carbonation of mineral crystals by Raman spectroscopy. Since little is known about enthesis biological plasticity, our second objective was to examine the effects of unloading and reloading, using a mouse hindlimb-unloading model, on both the micromechanical properties and the mineral phase of the ATE. Elastic modulus, hardness, degree of mineralization, and degree of carbonation were assessed after 14 days of hindlimb suspension and again after a subsequent 6 days of reloading. The elastic modulus gradually increased along the mineralized part of the ATE from the tidemark to the subchondral bone, with the same trend being found for hardness. Whereas the degree of carbonation did not differ according to zone of measurement, the degree of mineralization increased by >70 % from tidemark to subchondral bone. Thus, the gradient in micromechanical properties is in part explained by a mineralization gradient. A 14-day unloading period did not appear to affect the gradient of micromechanical properties of the ATE, nor the degree of mineralization or carbonation. However, contrary to a short period of unloading, early return to normal mechanical load reduced the micromechanical properties gradient, regardless of carbonate-to-phosphate ratios, likely due to the more homogeneous degree of mineralization. These findings provide valuable data not only for tissue bioengineering, but also for musculoskeletal clinical studies and microgravity studies focusing on long-term space travel by astronauts.

The field stress of the shale affects the proppant embedment, fracture conductivity, well production rate, and ultimately the recovery of hydrocarbons from reservoir formations. This paper presents, for the first time, an experimental study investigating the mechanical characteristics of a shale under confining pressures that simulate the in situ stress state in deep reservoirs. Bidirectional but equal confining pressures were applied to the shale sample to replicate its field stress state. Microindentation tests were conducted to assess the alterations of mechanical properties resulting from the application of confining pressures. The results demonstrate a significant increase in Young’s modulus, hardness, and fracture toughness for the samples subjected to confining pressure. Considering the effect of confining pressure, the decrease in proppant embedment is proportional to Young’s modulus of the shale. For larger-sized proppants (e.g., D = 2.50 mm), the influence of confining pressure on fracture conductivity is relatively minor. However, when smaller-sized proppants (e.g., D = 1.00 mm) are used, particularly in scenarios involving shale debris swelling due to prolonged interaction with fracturing fluid, there is a noticeable improvement in fracture conductivity. Importantly, previous computational models have tended to overestimate proppant embedment depth while underestimating fracture conductivity. The findings from this study contribute to advancing the understanding of shale’s mechanical characteristics under in situ reservoir conditions and support the optimization of proppant embedment and fracture conductivity calculation models for the efficient extraction of shale gas.

The effect of small impurities of reduced graphene oxide (rGO) on microhardness of polyethylene (PЕ) and polypropylene (PP) matrices and the reaction of these nanocomposites and initial polymers on the influence of localized load in the temperature range of 77–295 K were studied. When rGO was introduced, PE practically did not change its properties, whereas the introduction of 0.3 wt% rGO into the PP matrix was accompanied by a significant increase in microhardness, especially in the room temperature range (by approximately 70%). A transition to reversible deformation was detected when the indenter impressions applied in liquid and gaseous nitrogen at temperatures below the threshold (T < 174.5 K for PP and T < 226.5 K for nanocomposite PP + 0.3 wt% rGO) were not fixed on the surface of the samples after their heating in the measuring device to room temperature. [ABSTRACT FROM AUTHOR]

The aim of this study is to investigate the influence of cross-linking and reinforcements in gelatin on the physico-mechanical properties of obtained composites. The gelatin-based composites cross-linked with citric acid (CA) were prepared: gelatin type B (GB) and β-tricalcium phosphate (β-TCP) and novel hybrid composite GB with β-TCP and hydroxyapatite (HAp) particles, and their structure, thermal, and mechanical properties were compared with pure gelatin B samples. FTIR analysis revealed that no chemical interaction between the reinforcements and gelatin matrix was established during the processing of hybrid composites by the solution casting method, proving the particles had no influence on GB cross-linking. The morphological investigation of hybrid composites revealed that cross-linking with CA improved the dispersion of particles, which further led to an increase in mechanical performance. The microindentation test showed that the hardness value was increased by up to 449%, which shows the high potential of β-TCP and HAp particle reinforcement combined with CA as a cross-linking agent. Furthermore, the reduced modulus of elasticity was increased by up to 288%. Results of the MTT assay on L929 cells have revealed that the hybrid composite GB-TCP-HA-CA was not cytotoxic. These results showed that GB cross-linked with CA and reinforced with different calcium phosphates presents a valuable novel material with potential applications in dentistry.

The indentation load-size effect was investigated during hardness testing of high entropy carbides with different hardness, applying indentation loads from 50 mN to 10 N. The experimental systems were recently developed (Hf-Ta-Zr-Nb-Ti)C and (Mo–Nb–Ta–V–W)C high-entropy carbides, prepared by ball milling and a spark plasma sintering, with single-phase and high relative density of 99.4% and 99.0%, respectively. The load dependence of hardness was analysed using the traditional Meyer's law, the proportional specimen resistance model and the modified proportional specimen resistance model. The best correlation (R 2 > 0.99) between the measured values and the used models was achieved using the modified proportional specimen resistance model. This resulted in the so-called load-independent hardness of (Hf-Ta-Zr-Nb-Ti)C and (Mo–Nb–Ta–V–W)C systems 21.96 and 14.81 GPa in the case of analyses for 50 mN–10 N load range and 25.42 GPa and 14.13 GPa in the case of 50 mN–1 N load range, respectively. The different deformation and damage mechanisms detected as a potential reason for the origin of the load-size effect were microcracks at grain boundaries during the micro/macro-indentation and plastic deformation/nanocrack formation at the indents during nano/micro-indentation. [ABSTRACT FROM AUTHOR]

The use of locally available industrial by-products as supplementary cementitious materials and mineral fillers is vital for reducing the embodied carbon of modern concretes. Spent pot lining (SPL), a by-product of the aluminum industry, is massively produced worldwide. SPL treated with the low caustic leaching and liming process (LCLL-ash) is no more hazardous and can be used as cementitious material. This study aims to better understand the microstructure changes of cement paste incorporating aluminum smelter wastes, such as LCLL-ash and synthetic anhydrite. Ground LCLL-ash was used to partially replace cement in cement pastes with a constant water-to-binder ratio of 0.35. A small amount of anhydrite was added to some mixes. This study investigated chemo-micromechanical properties of cement paste systems through multiple techniques, including X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, wavelength-dispersive spectroscopy, and microindentation test. The results showed that the reactive alumina from LCLL-ash modified the hydrated phases with the presence of the carbo-aluminate phases. The pastes containing LCLL-ash exhibited a higher CH, and C-S-H contents refer to the reference, suggesting that LCLL-ash has a slight nucleation effect. Moreover, LCLL cement paste showed an increase in the Ca/Si ratio of the C-S-H phase intermix. Finally, microindentation results revealed that adding anhydrite with 10% LCLL-ash enhanced the mechanical property of the cement paste at 28 days. [ABSTRACT FROM AUTHOR]

Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone’s corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte.

In this paper, the composites with the matrix of gelatin (GA) and poly(vinylpyrrolidone) (PVP) blend with nanoparticles of zinc oxide (ZnO) were prepared. In order to improve the mechanical properties, the samples were cross-linked with glutaraldehyde (GTA). The processing was carried out by the solution casting method, and the influence of cross-linking and nanoparticles on the mechanical properties of the obtained composites was investigated. FTIR analysis confirmed the cross-linking of the polymer matrix and that no chemical bond was formed during processing between the polymer matrix and zinc oxide nanoparticles. Examination of the mechanical properties showed that the cross-linking and addition of 1 wt% zinc oxide increased tensile strength, modulus of elasticity, hardness and reduced modulus of elasticity.

Copyright of Metallophysics & Advanced Technologies / Metallofizika i Novejsie Tehnologii is the property of G.V. Kurdyumov Institute for Metal Physics, N.A.S.U and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Background: The impact of tenofovir disoproxil fumarate (TDF) antiretroviral (ART) regimens on bone health has been characterized mostly by bone mineral density (BMD), but recently also by bone quality (BQ). The aim of this pilot study is to assess the changes in BMD and BQ after switch from TDF to tenofovir alafenamide (TAF) ART. Methods: HIV individuals receiving TDF-based ART were randomized to switch to Bictegravir-TAF-Emtricitabine or to remain in the same regimen. At baseline and 24-weeks after randomization, participants underwent bone mineral density (BMD) by DXA and BQ assessment using bone microindentation, a validated technique that measures bone tissue quality expressed as bone material strength index (BMSi). A panel of plasma bone turnover biomarkers were measured by ELISA at the same time-points. Values are expressed as median [interquartile range] and non-parametric tests were used where appropriate. Results: A total of 24 HIV individuals were included in the study, 19 of which were men (80%). Median age at baseline was 43 years (IQR 38-54). Half of individuals were allocated in the TDF group while the other half changed to TAF treatment. No differences at baseline between both groups were detected in any parameter. Non-significant changes nor in lumbar or femoral BMD at week 24 was found in any regimen. In contrast, there was an increase in BMSi in the TAF arm at 24 weeks, and thus an improvement in BQ[81.6 (79-83) to 86 (80-88) (+5.1%); p=0.041], whereas the TDF arm remained stable from 82 (76-85) at baseline to 82 (73-83);p=0.812. Hence, at week 24 there were significant differences in BQ between arms (p=0.049). A reduction in bone formation markers was found at week 24 in both regimens: N-terminal propeptide of type-1 collagen decreased a 20% (-35 - -0.6); p=0.031 with TAF and -16% (-25 - -5); p=0.032 with TDF. Also a decrease in bone resorption marker C-telopeptide with TAF was detected [-10% (-19 - -5);p=0.028] but not with TDF (p=0.232), suggesting a less metabolically active bone after switching to TAF. Conclusion: A bone quality improvement was found after switching from a TDF to a TAF based ART independently of BMD, suggesting that the bone health benefits of TAF may extend beyond BMD. Future research should be directed to confirm these findings and to identify the underlying mechanisms of ART related bone toxicity. [ABSTRACT FROM AUTHOR]

Morphology, macro-, and micromechanical properties of novel poly(urethane-urea)/silica nanocomposites were analyzed by electron microscopy, dynamic mechanical thermal analysis, and microindentation. The studied nanocomposites were based on a poly(urethane-urea) (PUU) matrix filled by nanosilica, and were prepared from waterborne dispersions of PUU (latex) and SiO2. The loading of nano-SiO2 was varied between 0 (neat matrix) and 40 wt% in the dry nanocomposite. The prepared materials were all formally in the rubbery state at room temperature, but they displayed complex elastoviscoplastic behavior, spanning from stiffer elastomeric type to semi-glassy. Because of the employed rigid and highly uniform spherical nanofiller, the materials are of great interest for model microindentation studies. Additionally, because of the polycarbonate-type elastic chains of the PUU matrix, hydrogen bonding in the studied nanocomposites was expected to be rich and diverse, ranging from very strong to weak. In micro- and macromechanical tests, all the elasticity-related properties correlated very strongly. The relations among the properties that related to energy dissipation were complex, and were highly affected by the existence of hydrogen bonding of broadly varied strength, by the distribution patterns of the fine nanofiller, as well as by the eventual locally endured larger deformations during the tests, and the tendency of the materials to cold flow. [ABSTRACT FROM AUTHOR]

This paper evaluates the creep behavior of wollastonite-microfiber-reinforced hardened cement paste. A parametric study was performed for cementitious mixtures with partial replacement of cement using wollastonite. The samples were subjected to uniaxial compression and microindentation experiments. The compressive strength significantly improved by up to 30% for the mixture containing 10% wollastonite fiber. Microindentation experiments were performed to evaluate the creep response and time-dependent performance of both the control and the wollastonite-fiber-reinforced samples. Approximately 36% increase in creep modulus was observed with 10% wollastonite fiber content. This indicates a significant improvement in creep behavior, which can be attributed to the micro-reinforcing effect of the fibers. No significant impact was observed for time characteristic of creep with the incorporation of wollastonite fibers. Overall, the study establishes a cost-effective, sustainable, and efficient route to enhance the creep behavior of hardened cement paste for a wide range of infrastructural applications. [ABSTRACT FROM AUTHOR]

Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone's corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte. [ABSTRACT FROM AUTHOR]

BackgroundThe impact of tenofovir disoproxil fumarate (TDF) antiretroviral (ART) regimens on bone health has been characterized mostly by bone mineral density (BMD), but recently also by bone quality (BQ). The aim of this pilot study is to assess the changes in BMD and BQ after switch from TDF to tenofovir alafenamide (TAF) ART.MethodsHIV individuals receiving TDF-based ART were randomized to switch to Bictegravir-TAF-Emtricitabine or to remain in the same regimen. At baseline and 24-weeks after randomization, participants underwent bone mineral density (BMD) by DXA and BQ assessment using bone microindentation, a validated technique that measures bone tissue quality expressed as bone material strength index (BMSi). A panel of plasma bone turnover biomarkers were measured by ELISA at the same time-points. Values are expressed as median [interquartile range] and non-parametric tests were used where appropriate.ResultsA total of 24 HIV individuals were included in the study, 19 of which were men (80%). Median age at baseline was 43 years (IQR 38-54). Half of individuals were allocated in the TDF group while the other half changed to TAF treatment. No differences at baseline between both groups were detected in any parameter. Non-significant changes nor in lumbar or femoral BMD at week 24 was found in any regimen. In contrast, there was an increase in BMSi in the TAF arm at 24 weeks, and thus an improvement in BQ[81.6 (79-83) to 86 (80-88) (+5.1%);p=0.041], whereas the TDF arm remained stable from 82 (76-85) at baseline to 82 (73-83);p=0.812. Hence, at week 24 there were significant differences in BQ between arms (p=0.049). A reduction in bone formation markers was found at week 24 in both regimens: N-terminal propeptide of type-1 collagen decreased a 20% (-35 - -0.6); p=0.031 with TAF and -16% (-25 - -5); p=0.032 with TDF. Also a decrease in bone resorption marker C-telopeptide with TAF was detected [-10% (-19 - -5);p=0.028] but not with TDF (p=0.232), suggesting a less metabolically active bone after switching to TAF.ConclusionA bone quality improvement was found after switching from a TDF to a TAF based ART independently of BMD, suggesting that the bone health benefits of TAF may extend beyond BMD. Future research should be directed to confirm these findings and to identify the underlying mechanisms of ART related bone toxicity.

We compared the results of various microscale indentation creep (microcreep) measurements with macroscale tensile creep (macrocreep) measurements of three common polymers: high-density polyethylene (PE), polypropylene (PP), and polystyrene (PS). The main objective was to verify if the short-term microcreep experiments could predict long-term macrocreep behavior of the selected polymers, whose properties ranged from very soft and ductile (PE) to very hard and brittle (PS). The second objective was to compare several creep predictive schemes: the empirical power law model (PL) and several types of phenomenological elasto-visco-plastic models (EVP). In order to facilitate this task, we developed a universal program package named MCREEP, which fits PL and EVP models to both tensile and indentation creep data. All experimental results and theoretical predictions documented that: (i) regardless of the creep experiment type, both micro- and macrocreep resistance increased in the following order: PE < PP < PS, (ii) the short-term microcreep experiments could be used to predict qualitatively the long-term macrocreep behavior, and (iii) the simple empirical power law model yielded better predictions of long-term creep behavior than the more sophisticated elasto-visco-plastic models. [ABSTRACT FROM AUTHOR]

Surface texturing is an engineering technology used in order to improve the surface characteristic of plastic parts obtained by injection molding. Applying this process not only changes the part surface properties, but also its topography. The novel functionalities of plastic products become useful when other materials make contact with the textured surface. Of course, these characteristics may vary depending on the laser positioning, dimensions, and geometry of the texture. The present paper presents the surface characteristics obtained after the laser texturing of the Arboblend V2 Nature biodegradable polymer. Three distinct geometries were studied: hexagonal, square, and triangular, and different behaviors of them were highlighted during surface free energy (SFE) and contact angle (WCA) measurements: a hydrophobic character for square and hexagonal geometry with distilled water as the measure liquid, and a hydrophilic character with diiodomethane as the measure liquid; for triangle geometry, the contact angle measurements were impossible to extract because the drop turns into a flat puddle. Additionally, the friction coefficient varied depending on the geometry texture, with the lowest value being recorded by the sample with hexagonal geometry. The micro-indentation tests highlighted increased surface micro-hardness compared to the basic material. The possibility of use in the practice of textured surfaces is viable; thus, based on the obtained results, there is even the possibility to replace non-biodegradable polymers from different sectors of activity. [ABSTRACT FROM AUTHOR]

In this article, the characteristic curves of microindentation measured on Cu99 were analyzed on the basis of the analytical expression proposed by Habibi et al. (J. Mater. Res, 2021, 36 (15): 3074-3085). The ratio of applied load to square displacement, P/(h+h0)2, was discovered to be non-constant during the loading segment of the microindentation test. An empirical expression for the determination of Martens hardness as a function of indentation load, contact stiffness, and reduced modulus of elasticity by analyzing indentation load curves has been proposed for pile-up mode strain with the corrections imposed by the tip defect, the compliance of the instrument, and the axial axisymmetry coefficient of the Vickers indenter. The results from microindentation tests on this examined ductile material show excellent agreement.

In this paper dislocations and twins formed under Vickers indentation of different planes of CdWO 4 crystals are studied. It has been found that on (010) and (100) faces fresh dislocations run along [001] from an imprint of Vickers pyramid. On (001) twins with (010) twinning plane induced by indenter propagate along [100]. Twins with {011} twin planes are induced by indentation on (100). Possible dislocation dissociation reactions and role of the resulting partial dislocations in twinning during microindentaion in cadmium tungstate are discussed. [ABSTRACT FROM AUTHOR]

This article discusses the micromechanical properties and true microhardness determination of nanostructured tribological coatings (NTCs) based on a multilayered alternating nitride/carbonitride bilayer substructure for transition metals. The constituent nitride/carbonitride bilayers in the superlattice structure of the NTC were alloyed with refractory metals, denoted as Me = Me1 or Me2= Cr, Hf, Nb, W, and Zr. The resulting NTC coatings were deposited onto 100Cr6 steel substrates using an advanced physical vapor deposition (PVD) technique, referred to here as high-power ion-plasma magnetron sputtering (HiPIPMS). The comprising crystalline nanometer-scale TiAlSiMe1-N/TiMe2-CN nanoparticles strengthened by Me additives significantly increased the NTC microhardness to over 3200 HV. The primary focus of this research was to determine the true microhardness of the NTC film samples. The apparent microhardness (Ha) of the film/substrate system for various NTC samples was measured during microindentation testing using the Vickers method. Nine NTC samples were tested, each generating a corresponding microindentation dataset containing between 430 and 640 imprints, depending on the specific NTC sample. These datasets were analyzed using three distinct empirical approaches: (i) the inverse power-law model (IPL-Model), (ii) the sigmoid-like decay model (SLD-Model), and (iii) the error function model (ERF-Model). The observed solid correlation between the proposed models and experiments suggests that the true microhardness estimates (Hf) obtained through the empirical mathematical modeling approach are reliable.

In this work, a blend of gelatin A (GA) and polyvinylpyrrolidone (PVP K30) was used for semi-solid 3D printing of bone scaffold for ibuprofen (IBU) delivery. The cross-linking of the obtained scaffold was performed with a 1% glutaraldehyde (GTA) solution, followed by lyophilization. The thermal and mechanical properties, as well as drug release profiles, and drug kinetics of prepared scaffolds were investigated. The cross-linked and lyophilized scaffold has shown good thermal stability, mechanical properties, and prolonged release of IBU following the Fickian diffusion process.

Although multiple structural, mechanical, and molecular factors are definitely involved in osteoporosis, the assessment of subregional bone mineral density remains the most commonly used diagnostic index. In this study, we characterized bone quality in the femoral neck of one osteoporotic patients as compared to an age-matched control subject, and so used a multiscale and multimodal approach including X-ray computed microtomography at different spatial resolutions (pixel size: 51.0, 4.95 and 0.9 µm), microindentation and Fourier transform infrared spectroscopy. Our results showed abnormalities in the osteocytes lacunae volume (358.08 ± 165.00 for the osteoporotic sample vs. 287.10 ± 160.00 for the control), whereas a statistical difference was found neither for shape nor for density. The osteoporotic femoral head and great trochanter reported reduced elastic modulus (Es) and hardness (H) compared to the control reference (−48% (p < 0.0001) and −34% (p < 0.0001), respectively for Es and H in the femoral head and −29% (p < 0.01) and −22% (p < 0.05), respectively for Es and H in the great trochanter), whereas the corresponding values in the femoral neck were in the same range. The spectral analysis could distinguish neither subregional differences in the osteoporotic sample nor between the osteoporotic and healthy samples. Although, infrared spectroscopic measurements were comparable among subregions, and so regardless of the bone osteoporotic status, the trabecular mechanical properties were comparable only in the femoral neck. These results illustrate that bone remodeling in osteoporosis is a non-uniform process with different rates in different bone anatomical regions, hence showing the interest of a clear analysis of the bone microarchitecture in the case of patients' osteoporotic evaluation. [ABSTRACT FROM AUTHOR]

Assessing the mechanical properties of materials is of fundamental relevance for their rational usage, but can be challenging with standard tensile testing for highly brittle polymers used, e.g., as coatings. Here, a procedure for the mechanical analysis of free-standing poly(alkyl cyanoacrylate) (PACA) films using microindentation has been explored. Rigid and transparent films from PACA with various side chain compositions were formed on top of square polymer frames by in situ polymerization. Under microscopic control, the free-standing films were analyzed using a microelectromechanical sensing system. By this procedure, decreasing Young's moduli E for increasing PACA side chain length and flexibility were determined with strain at break εB between 0.36% for poly(ethyl cyanoacrylate) and 4.6% for poly(methoxyethyl cyanoacrylate). Based on this successful application, the applied methodology may be relevant for characterizing various coating materials, which are otherwise hard to form as thin free-standing films, and using the data, e.g., in computationally assisted design and evaluation of hybrid material devices. [ABSTRACT FROM AUTHOR]

Distraction osteogenesis (DO) involves several processes to form an organized distracted callus. While bone regeneration during DO has been widely described, no study has yet focused on the evolution profile of mechanical properties of mineralized tissues in the distracted callus. The aim of this study was therefore to measure the elastic modulus and hardness of calcified cartilage and trabecular and cortical bone within the distracted callus during the consolidation phase. We used a microindentation assay to measure the mechanical properties of periosteal and endosteal calluses; each was subdivided into two regions. Histological sections were used to localize the tissues. The results revealed that the mechanical properties of calcified cartilage did not evolve over time. However, trabecular bone showed temporal variation. For elastic modulus, in three out of four regions, a similar evolution profile was observed with an increase and decrease over time. Concerning hardness, this evolves differently depending on the location in the distracted callus. We also observed spatial changes in between regions. A first duality was apparent between regions close to the native cortices and the central area, while latter differences were seen between periosteal and endosteal calluses. Data showed a heterogeneity of mechanical properties in the distracted callus with a specific mineralization profile. [ABSTRACT FROM AUTHOR]

Growing evidence suggests that diabetes mellitus is associated with an increased risk of fracture. Bone intrinsic factors (such as accumulation of glycation end products, low bone turnover, and bone microstructural changes) and extrinsic factors (such as hypoglycemia caused by treatment, diabetes peripheral neuropathy, muscle weakness, visual impairment, and some hypoglycemic agents affecting bone metabolism) probably contribute to damage of bone strength and the increased risk of fragility fracture. Traditionally, bone mineral density (BMD) measured by dual x-ray absorptiometry (DXA) is considered to be the gold standard for assessing osteoporosis. However, it cannot fully capture the changes in bone strength and often underestimates the risk of fracture in diabetes. The fracture risk assessment tool is easy to operate, giving it a certain edge in assessing fracture risk in diabetes. However, some parameters need to be regulated or replaced to improve the sensitivity of the tool. Trabecular bone score, a noninvasive tool, indirectly evaluates bone microstructure by analyzing the texture sparsity of trabecular bone, which is based on the pixel gray level of DXA. Trabecular bone score combined with BMD can effectively improve the prediction ability of fracture risk. Quantitative computed tomography is another noninvasive examination of bone microstructure. High-resolution peripheral quantitative computed tomography can measure volume bone mineral density. Quantitative computed tomography combined with microstructure finite element analysis can evaluate the mechanical properties of bones. Considering the invasive nature, the use of microindentation and histomorphometry is limited in clinical settings. Some studies found that the changes in bone turnover markers in diabetes might be associated with fracture risk, but further studies are needed to confirm this. This review focused on summarizing the current development of these assessment tools in diabetes so as to provide references for clinical practice. Moreover, these tools can reduce the occurrence of fragility fractures in diabetes through early detection and intervention. [ABSTRACT FROM AUTHOR]

Background: The risk of fractures is increased in persons with type 1 diabetes (T1D) and assessment of bone health has been included in the 2024 updated Standards of Care by The American Diabetes Association (ADA). Previous studies have found that in T1D bone metabolism, mineral content, microstructure, and strength diverge from that of persons without diabetes. However, a clear description of a T1D bone phenotype has not yet been established. We investigated bone mechanical properties and microstructure in T1D compared with healthy controls. For the potential future introduction of additional bone measures in the clinical fracture risk assessment, we aimed to assess any potential associations between various measures related to bone indices in subjects with T1D., Methods: We studied human bone indices in a clinical cross-sectional setup including 111 persons with early-onset T1D and 37 sex- and age-matched control persons. Participants underwent hip and spine DXA scans for bone mineral density (BMD) of the femoral neck (FN), total hip (TH), and lumbar spine (LS), and TBS evaluation, microindentation of the tibial shaft for Bone Material Strength index (BMSi), and high-resolution periphery quantitative computed tomography (HRpQCT) of the distal radius and tibia for volumetric BMD (vBMD) and structural measures of trabecular and cortical bone. Results are reported as means with (standard deviation) or (95 % confidence intervals (CI)), medians with [interquartile range], and differences are reported with (95 % CI)., Results: The study included 148 persons aged 20 to 75 years with a median age of 43.2 years. The T1D group who had all been diagnosed with T1D before the age of 18 years demonstrated values of HbA1c ranging from 39 to 107 mmol/mol and a median HbA1c of 57 mmol/mol. The BMD did not differ between groups (the mean difference in FN-BMD was 0.026 g/cm 2 (-0.026; 0.079), p = 0.319) and the median BMSi was comparable in the two groups (79.2 [73.6; 83.8] in the T1D group compared with 77.9 [70.5, 86.1] in the control group). Total and trabecular vBMD (Tb.vBMD), cortical thickness (Ct.Th), and trabecular thickness (Tb.Th) of both radius and tibia were lower in participants with T1D. The mean Tb.vBMD at the radius was 143.6 (38.5) mg/cm 3 in the T1D group and 171.5 (37.7) mg/cm 3 in the control group, p < 0.001. The mean Ct. Th d of the radius was 0.739 mm (0.172) in the T1D group and 0.813 (0.188) in the control group, p = 0.044. Crude linear regressions revealed limited agreement between BMSi and Tb.vBMD (p = 0.010, r 2  = 0.040 at the radius and p = 0.008, r 2  = 0.040 at the tibia and between BMSi and the estimated failure load (FL) at the tibia (p < 0.001, r 2  = 0.090). There were no significant correlations between BMSi and Ct.Th. TBS correlated with Tb.vBMD at the radius (p = 0.008, r 2  = 0.044) and the tibia (p = 0.001, r 2  = 0.069), and with the estimated FL at the distal tibia (p = 0.038, r 2  = 0.026)., Conclusion: In this study, we examined the bones of persons with well-controlled, early-onset T1D. Compared with sex- and age-matched healthy control persons, we found reduced total and trabecular vBMD, as well as decreased trabecular and cortical thickness. These results suggest that a debut of T1D before reaching peak bone mass negatively impacts bone microarchitecture. No differences in areal BMD or BMSi were observed. Although the variations in total hip BMD reflect some variation in the vBMD, the reduction in trabecular bone mineral density was not captured by the DXA scan. Consequently, fracture risk may be underestimated when relying on DXA, and further research into fracture risk assessment in T1D is warranted., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Inge Gerlach reports financial support was provided by Novo Nordic Foundation. Rikke Viggers reports financial support was provided by Amgen Inc. Morten Frost reports equipment, drugs, or supplies was provided by Novo Nordisk. Rikke Viggers reports a relationship with Novo Nordisk that includes: equity or stocks. Rikke Viggers reports a relationship with Amgen Inc. that includes: equity or stocks. Rikke Viggers reports a relationship with Eli Lilly that includes: equity or stocks. Morten Frost reports a relationship with Novo Nordisk that includes: equity or stocks. Morten Frost assumed a position at Novo Nordisk A/S after completion of the study If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Inc.)

Displaced fractures of patella often require open reduction surgery and internal fixation to restore the extensor continuity and articular congruity. Fracture fixation with biodegradable magnesium (Mg) pins enhanced fracture healing. We hypothesized that fixation with Mg pins and their degradation over time would enhance healing of patellar fracture radiologically, mechanically, and histologically. Transverse patellar fracture surgery was performed on thirty-two 18-weeks old female New Zealand White Rabbits. The fracture was fixed with a pin made of stainless steel or pure Mg, and a figure-of-eight stainless steel band wire. Samples were harvested at week 8 or 12, and assessed with microCT, tensile testing, microindentation, and histology. Microarchitectural analysis showed that Mg group showed 12% higher in the ratio of bone volume to tissue volume at week 8, and 38.4% higher of bone volume at week 12. Tensile testing showed that the failure load and stiffness of Mg group were 66.9% and 104% higher than the control group at week 8, respectively. At week 12, Mg group was 60.8% higher in ultimate strength than the control group. Microindentation showed that, compared to the Control group, Mg group showed 49.9% higher Vickers hardness and 31% higher elastic modulus at week 8 and 12, respectively. At week 12, the new bone of Mg group remodelled to laminar bone, but those of the control group remained woven bone-like. Fixation of transverse patellar fracture with Mg pins and its degradation enhanced new bone formation and mechanical properties of the repaired patella compared to the Control group.

In the present study, the intelligent addition of Re and Al to TiZrHf equiatomic ternary alloy resulted in a new single-phase Ti30Zr30Hf30Re5Al5 HCP high entropy alloy. The XRD analyses show that the TiZrHfRex alloys have a single-phase HCP structure until x = 5 at.%. Subsequently, the TiZrHfRe5 retains its single-phase HCP microstructure with the addition of Al upto 5 at.%, leading to a new quinary TiZrHfRe5Al5 HCP HEA. Microstructural investigations using SEM revealed the formation of compositionally homogeneous single-phase HCP solid solution for TiZrHf, TiZrHfRe5 and TiZrHfRe5Al5 alloys. Vicker's microindentation measurements revealed that adding Re, followed by Al, increases the hardness of the TiZrHf ternary alloy from 7.85 ± 0.37–8.35 ± 0.42 GPa. In a nutshell, a novel quinary HCP alloy was developed based on transition metals, allowing HCP HEA compositional space to expand beyond rare-earth (RE) based HEAs. [ABSTRACT FROM AUTHOR]

Micro-scratch test was used to evaluate the fracture toughness of the main hydration products of ordinary Portland cement paste at the micro-scale. The evaluation was done with the aid of scanning electron microscopy and acoustic emission (AE) signals. Portlandite was found to be the only phase where AE detected elastic waves due to cracking during microindentation and micro-scratch test. Such behavior simplifies phase separation during the evaluation process of the micro-scratch test. The micro-scale fracture toughness results obtained from the tests were found in close agreement with other available experiments and models in the literature. [ABSTRACT FROM AUTHOR]

Objective: Type 1 diabetes (T1D) is associated with substantial fracture risk. Bone mineral density (BMD) is, however, only modestly reduced, suggesting impaired bone microarchitecture and/or bone material properties. Yet, the skeletal abnormalities have not been uncovered. Men with T1D seem to experience a more pronounced bone loss than their female counterparts. Hence, we aimed to examine diffe rent aspects of bone quality in men with T1D. Design and Methods: In this cross-sectional study, men with T1D and healthy male controls were enrolled. BMD (femoral neck, total hip, lumbar spine, whole body) and spine trabecular bone score (TBS) were measured by dual x-ray absorptiometry, and bone material strength index (BMSi) was measured by in vivo impact microindentation. HbA1c and bone turnover markers were analyzed. Results: Altogether, 33 men with T1D (43 ± 12 years) and 28 healthy male controls (42 ± 12 years) were included. Subjects with T1D exhibited lower whole-body BMD than controls (P = 0.04). TBS and BMSi were attenuated in men with T1D vs controls (P = 0.016 and P = 0.004, respectively), and T1D subjects also had a lower bone turnover. The bone parameters did not differ between subjects with or without diabe tic complications. Duration of disease correlated negatively with femoral neck BMD but not with TBS or BMSi. Conclusions: This study revealed compromised bone material strength and microarchitecture in men with T1D. Moreover, our data confirm pr evious studies which found a modest decrease in BMD and low bone turnover in subjects with T1D. Accordingly, bone should be recognized as a target of diabetic complications.

Gelatin methacryloyl (GelMA) hydrogels are widely used for a variety of tissue engineering applications. The properties of gelatin can affect the mechanical properties of gelatin gels; however, the role of gelatin properties such as bloom strength on GelMA hydrogels has not yet been explored. Bloom strength is a food industry standard for describing the quality of gelatin, where higher bloom strength is associated with higher gelatin molecular weight. Here, we evaluate the role of bloom strength on GelMA hydrogel mechanical properties. We determined that both bloom strength of gelatin and weight percent of GelMA influenced both stiffness and viscoelastic ratio; however, only bloom strength affected diffusivity, permeability, and pore size. With this library of GelMA hydrogels of varying properties, we then encapsulated Swan71 trophoblast spheroids in these hydrogel variants to assess how bloom strength affects trophoblast spheroid morphology. Overall, we observed a decreasing trend of spheroid area and Feret diameter as bloom strength increased. In identifying clear relationships between bloom strength, hydrogel mechanical properties, and trophoblast spheroid morphology, we demonstrate that bloom strength should considered when designing tissue engineered constructs. [ABSTRACT FROM AUTHOR]

Osteoarthritis (OA) is a chronic and complicated degenerative disorder of joints, including several phenotypes. Type 2 diabetes mellitus (T2DM) is one of the major causes of OA. However, few studies on the mechanical behavior of diabetic cartilages have been conducted. This study evaluated the microstructural, compositional, and mechanical properties of healthy and diabetic rat cartilages using scanning electronic microscopy, X-ray energy spectroscopy, histology staining, and microindentation tests. Our results indicated that the diabetic cartilages had a significantly higher elastic modulus and similar permeability (95%CI: 3.72–8.56 MPa and 3.16×10−6–1.83×10−5 mm4/N·s) compared to the healthy cartilages (95%CI: 0.741–3.58 MPa and 3.15×10−6–1.14×10−5 mm4/N·s). Their stress relaxation behaviors were similar regardless of the loading rate except for the stretching parameter under the fast loading. Furthermore, the stress relaxation behaviors of the diabetic cartilages were significantly affected by the loading rate, especially the equilibrium force ratio and time constant. These mechanical outcomes could be attributed to the increase of fibril diameters and calcium aggregation in the cartilage. This study deepens our understanding of how T2DM might facilitate OA in cartilages, which could contribute to the development of more scientific diagnosis and therapies for patients with diabetes. • Type 2 diabetic cartilage had significant higher elastic modulus than healthy ones. • Loading rate significantly affected stress relaxation of type 2 diabetic cartilage. • Type 2 diabetic cartilage had larger fibril diameter in all the zones along the depth. • Calcium aggregations (f.i., cyst-like structures) exist in type 2 diabetic cartilages. [ABSTRACT FROM AUTHOR]

Introduction. Long-term non-progressors (LTNPs) are HIV-infected individuals (HIV+) whose viral replication is controlled. However, these individuals experience complications associated with HIV, among them, bone remodeling impairment. This study aims to perform a comprehensive bone health assessment and its association with the inflammatory status of HIV+ LTNPs. A cross-sectional study was conducted comparing bone strength components (bone mineral density and bone tissue quality) between age-, sex-, and comorbidities-matched groups of HIV+ LTNPs, HIV+ progressors, and HIV-negative individuals. A panel of bone turnover and inflammatory biomarkers was measured in fasting plasma using ELISA. Bone tissue quality was assessed by bone microindentation, a technique that directly measures the bone resistance to fracture and yields a dimensionless quantifiable parameter called bone material strength (BMSi). Thirty patients were included: ten LTNPs, ten HIV+ progressors, and ten HIV-negative individuals. LTNPs showed an abnormal pattern of immune activation that was represented by significantly lower levels of anti-inflammatory cytokine IL-10 (p = 0.03), pro-inflammatory cytokine IL-8 (p = 0.01), and TNF-α (p < 0.001) with respect to the other groups. Regarding bone health, LTNPs presented lower BMSi, and thus, worse bone tissue quality than HIV-negative individuals (83 (78–85) vs. 90 (89–93), respectively; p = 0.003), and also lower BMSi than HIV+ progressors (83 (78–85) vs. 86 (85–89), respectively; p = 0.022). A trend was found of lower BMSi in HIV+ progressors with respect to the HIV-negative individuals (86 (85–89) vs. 90 (89–93), respectively; p = 0.083). No differences were detected in bone mineral density between groups. In conclusion, LTNPs showed a different inflammatory profile, along with worse bone tissue quality, when compared to HIV+ progressors and HIV-negative individuals. This may contribute to increasing evidence that HIV infection itself has a deleterious effect on bone tissue, likely through a persistent altered inflammation status. [ABSTRACT FROM AUTHOR]

In postmenopausal women with osteoporosis, denosumab (DMAb) therapy through 10 years resulted in significantly higher degree of mineralization of bone, with a subsequent increase from years 2–3 to year 5 and no further difference between years 5 and 10. Our aim was to assess the variables reflecting the quality of bone mineral and organic matrix (Fourier transform infrared microspectroscopy), and the microhardness of bone (Vickers microindentation). Cross‐sectional assessments were performed in blinded fashion on iliac bone biopsies from osteoporotic women (72 from FREEDOM trial, 49 from FREEDOM Extension trial), separately in cortical and cancellous compartments. After 2–3 years of DMAb, mineral/matrix ratio and microhardness of cortical bone were significantly higher compared with placebo, whereas mineral maturity, mineral crystallinity, mineral carbonation, and collagen maturity were not different in both bone compartments. Through 5 years of DMAb, mineral carbonation was significantly lower and mineral/matrix ratio, mineral maturity, and crystallinity were significantly higher versus 2–3 years and were not different between 5 and 10 years, with the exception of mineral maturity in cancellous bone. These data support a transition of mineral to more mature crystals (within physiological range) and the completeness of secondary mineralization within 5 years of DMAb treatment. Microhardness in cortical and cancellous compartments was significantly lower at 5 years of DMAb versus 2–3 years and was not different from years 5 to 10. The lower microhardness at years 5 and 10 is likely the result of maturation of the organic matrix in a persistently low state of bone remodeling over 5 and 10 years. © 2022 American Society for Bone and Mineral Research (ASBMR). [ABSTRACT FROM AUTHOR]