Search

The exterior application of fire-retardant (FR) timber necessitates it to have high durability because of the possibility to be exposed to rainfall. In this study, water-leaching resistance of FR wood has been imparted by grafting phosphate and carbamate groups of the water-soluble FR additives ammonium dihydrogen phosphate (ADP)/urea onto the hydroxyl groups of wood polymers via vacuum-pressure impregnation, followed by drying/heating in hot air. A darker and more reddish wood surface was observed after the modification. Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, solid-state 13C cross-polarization magic-angle-spinning nuclear magnetic resonance (13C CP-MAS NMR), and direct-excitation 31P MAS NMR suggested the formation of C–O–P covalent bonds and urethane chemical bridges. Scanning electron microscopy/energy-dispersive X-ray spectrometry suggested the diffusion of ADP/urea into the cell wall. The gas evolution analyzed by thermogravimetric analysis coupled with quadrupole mass spectrometry revealed a potential grafting reaction mechanism starting with the thermal decomposition of urea. Thermal behavior showed that the FR-modified wood lowered the main decomposition temperature and promoted the formation of char residues at elevated temperatures. The FR activity was preserved even after an extensive water-leaching test, confirmed by the limiting oxygen index (LOI) and cone calorimetry. The reduction of fire hazards was achieved through the increase of the LOI to above 80%, reduction of 30% of the peak heat release rate (pHRR2), reduction of smoke production, and a longer ignition time. The modulus of elasticity of FR-modified wood increased by 40% without significantly decreasing the modulus of rupture. Validerad;2023;Nivå 2;2023-04-21 (joosat);Funder: OP RDE (Grant no.CZ.02.1.01/0.0/0.0/16_019/0000803); CT WOOD, Luleå University of TechnologyLicens fulltext: CC BY License

The reasons behind the occurrence of a second/end peak heat release rate (PHRR) during wood combustion under radiative heating were determined. Effects of the type of rear material, wood thickness, char progression, and its microstructure, as well as moisture content/transport in spruce wood, were studied. Rear materials used were insulating Kaowool, conducting steel, and the same wood but physically separated from test specimen by aluminium foil. The intensity of the second/end PHRR with Kaowool was almost 50% more than that of the sample with steel. Thus, the second/end peak is governed by the boundary condition defined by the rear material, which determines the heat losses at the rear side of the specimen and consequently the temperature of the specimen. Higher specimen temperature enhances the pyrolysis rate, thereby causing the second/end PHRR. The appearance times and values of the second/end PHRR for 30, 20, and 10 mm wood were 1740 s/78 kWm−2, 685 s/134 kWm−2, and 450 s/160 kWm−2, respectively. Char progressed to the rear of the samples even with a thin (8 mm) conductive steel substrate. Cracks in char grew almost three times wider during the second/end PHRR compared to the sample with no second/end peak. Char cracking had no significance on the time of occurrence of the second/end PHRR but affected the overall heat release. High moisture content reduced the charring rate and delayed the time of occurrence of the second/end PHRR as more water was needed to undergo a phase change, requiring a higher amount of energy. Validerad;2023;Nivå 2;2023-06-29 (sofila)

This study provides an analysis on the fire safety of passengers and the fire protection of coaches and buses. A brief review of major bus fire incidents, an overview of current regulations in Europe, and their limitations are presented. The study finds that the current small-scale fire test methods described in UN ECE Reg No. 118 need to be replaced by test methods that can assess the reaction to fire of materials when exposed to ignition sources of varying sizes. To address these shortcomings, the study proposed an expert recommendation to update the material fire safety requirements and testing for buses. Additional measures are proposed, derived from objectives and strategies applied in other transport sectors, and can be tested through existing European and international standards, which are widely used by several industries. These measures aim to extend the time with tenable conditions for a safe evacuation in case of fire, reduce the degree of damage to buses, reduce the risk for fast and excessive thermal exposure on modern energy carriers needed for a more sustainable transport sector. Licens fulltext: CC BY-NC-ND License

3D printing or additive manufacturing (AM) is considered as a flexible manufacturing method with the potential for substantial innovations in fabricating geometrically complicated structured polymers, metals, and ceramics parts. Among them, polymeric composites show versatility for applications in various fields, such as constructions, microelectronics and biomedical. However, the poor resistance of these materials against fire must be considered due to their direct relation to human life conservation and safety. In this article, the recent advances in the fire behavior of 3D-printed polymeric composites are reviewed. The article describes the recently developed methods for improving the flame retardancy of 3D-printed polymeric composites. Consequently, the improvements in the fire behavior of 3D-printed polymeric materials through the change in formulation of the composites are discussed. The article is novel in the sense that it is one of the first studies to provide an overview regarding the flammability characteristics of 3D-printed polymeric materials, which will further incite research interests to render AM-based materials fire-resistant.

Guanyl-urea phosphate (GUP) was introduced into furfurylated wood in order to improve fire retardancy. Modified wood was produced via vacuum-pressure impregnation of the GUP–furfuryl alcohol (FA) aqueous solution, which was then polymerized at elevated temperature. The water leaching resistance of the treated wood was tested according to European standard EN 84, while the leached water was analyzed using ultra-performance liquid chromatography (UPLC) and inductively coupled plasma–sector field mass spectrometry (ICP-SFMS). This new type of furfurylated wood was further characterized in the laboratory by evaluating its morphology and elemental composition using optical microscopy and electron microscopy coupled with energy-dispersive X-ray spectrometry (SEM-EDX). The chemical functionality was detected using infrared spectroscopy (FTIR), and the fire resistance was tested using cone calorimetry. The dimensional stability was evaluated in wet–dry soaking cycle tests, along with the mechanical properties, such as the Brinell hardness and bending strength. The fire retardancy of the modified furfurylated wood indicated that the flammability of wood can be depressed to some extent by introducing GUP. This was reflected in an observed reduction in heat release rate (HRR2) from 454.8 to 264.9 kW/m2, without a reduction in the material properties. In addition, this leaching-resistant furfurylated wood exhibited higher fire retardancy compared to conventional furfurylated wood. A potential method for producing fire-retardant treated furfurylated wood stable to water exposure has been suggested.

Guanyl-urea phosphate (GUP) was introduced into furfurylated wood in order to improve fire retardancy. Modified wood was produced via vacuum-pressure impregnation of the GUP-furfuryl alcohol (FA) aqueous solution, which was then polymerized at elevated temperature. The water leaching resistance of the treated wood was tested according to European standard EN 84, while the leached water was analyzed using ultra-performance liquid chromatography (UPLC) and inductively coupled plasma-sector field mass spectrometry (ICP-SFMS). This new type of furfurylated wood was further characterized in the laboratory by evaluating its morphology and elemental composition using optical microscopy and electron microscopy coupled with energy-dispersive X-ray spectrometry (SEM-EDX). The chemical functionality was detected using infrared spectroscopy (FTIR), and the fire resistance was tested using cone calorimetry. The dimensional stability was evaluated in wet-dry soaking cycle tests, along with the mechanical properties, such as the Brinell hardness and bending strength. The fire retardancy of the modified furfurylated wood indicated that the flammability of wood can be depressed to some extent by introducing GUP. This was reflected in an observed reduction in heat release rate (HRR

Scheimpflug lidar is a compact alternative to traditional lidar setups. With Scheimpflug lidar it is possible to make continuous range-resolved measurements. In this study we investigate the feasibility of a Scheimpflug lidar instrument for remote sensing in pool flames, which are characterized by strong particle scattering, large temperature gradients, and substantial fluctuations in particle distribution due to turbulence. An extinction coefficient can be extracted using the information about the transmitted laser power and the spatial extent of the flame. The transmitted laser power is manifested by the intensity of the ‘echo’ from a hard-target termination of the beam located behind the flame, while the information of the spatial extent of the flame along the laser beam is provided by the range-resolved scattering signal. Measurements were performed in heptane and diesel flames, respectively.

Filled hybrid composites are widely used in various structural applications where machining is critical. Hence, it is essential to understand the performance of the fibre composites’ machining behaviour. As such, a new hybrid structural composite was fabricated with redmud as filler and sisal fibre as reinforcement in polyester matrix. The composite was then tested for its drilling performance. A comprehensive drilling experiment was conducted using Taguchi L27 orthogonal array. The effect of the drill tool point angle, the cutting speed, the feed rate on thrust force, delamination, and burr formation were analysed for producing quality holes. The significance of each parameter was analysed, and the experimental outcomes revealed some important findings in the context of the drilling behaviour of sisal fibre/polyester composites with redmud as a filler. Spindle speed contributed 39% in affecting the thrust force, while the feed rate had the maximum influence of ca. 38% in affecting delamination.

The present study is aimed at investigating the effect of hybridisation on Kevlar/E-Glass based epoxy composite laminate structures. Composites with 3 mm thickness and 16 layers of fibre (14 layers of E-glass centred and 2 outer layers of Kevlar) were fabricated using compression moulding technique. The fibre orientation of the Kevlar layers had 3 variations (0, 45 and 60°), whereas the E-glass fibre layers were maintained at 0° orientation. Tensile, flexural, impact (Charpy and Izod), interlaminar shear strength and ballistic impact tests were conducted. The ballistic test was performed using a gas gun with spherical hard body projectiles at the projectile velocity of 170 m/s. The pre- and post-impact velocities of the projectiles were measured using a high-speed camera. The energy absorbed by the composite laminates was further reported during the ballistic test, and a computerised tomographic scan was used to analyse the impact damage. The composites with 45° fibre orientation of Kevlar fibres showed better tensile strength, flexural strength, Charpy impact strength, and energy absorption. The energy absorbed by the composites with 45° fibre orientation was 58.68 J, which was 14% and 22% higher than the 0° and 60° oriented composites.

Functionalized polyacrylonitrile (PAN) nanofibers were used in the present investigation to enhance the fracture behavior of carbon epoxy composite in order to prevent delamination if any crack propagates in the resin rich area. The main intent of this investigation was to analyze the efficiency of PAN nanofiber as a reinforcing agent for the carbon fiber-based epoxy structural composite. The composites were fabricated with stacked unidirectional carbon fibers and the PAN powder was functionalized with glycidyl methacrylate (GMA) and then used as reinforcement. The fabricated composites’ fracture behavior was analyzed through a double cantilever beam test and the energy release rate of the composites was investigated. The neat PAN and functionalized PAN-reinforced samples had an 18% and a 50% increase in fracture energy, respectively, compared to the control composite. In addition, the samples reinforced with functionalized PAN nanofibers had 27% higher interlaminar strength compared to neat PAN-reinforced composite, implying more efficient stress transformation as well as stress distribution from the matrix phase (resin-rich area) to the reinforcement phase (carbon/phase) of the composites. The enhancement of fracture toughness provides an opportunity to alleviate the prevalent issues in laminated composites for structural operations and facilitate their adoption in industries for critical applications.

Natural fibre-based composites are replacing traditional materials in a wide range of structural applications that are used in different environments. Natural fibres suffer from thermal shocks, which affects the use of these composites in cold environment. Considering these, a goal was set in the present research to investigate the impact of cryogenic conditions on natural fibre composites. Composites were developed using polyester as matrix and jute-fibre and waste Teak saw-dust as reinforcement and filler, respectively. The effects of six parameters, viz., density of saw-dust, weight ratio of saw-dust, grade of woven-jute, number of jute layers, duration of cryogenic treatment of composite and duration of alkaline treatment of fibres on the mechanical properties of the composite was evaluated with an objective to maximise hardness, tensile, impact and flexural strengths. Taguchi method was used to design the experiments and response-surface methodology was used to model, predict and plot interactive surface plots. Results indicated that the duration of cryogenic treatment had a significant effect on mechanical properties, which was better only up to 60 min. The models were found to be statistically significant. The study concluded that saw-dust of density 300 kg/m3 used as a filler with a weight ratio of 13 wt.% and a reinforcement of a single layer of woven-jute-fibre mat of grade 250 gsm subjected to alkaline treatment for 4 h in a composite that has undergone 45 min of cryogenic treatment presented an improvement of 64% in impact strength, ca. 21% in flexural strength, ca. 158% in tensile strength and ca. 28% in hardness.

Carbon based fillers have attracted a great deal of interest in polymer composites because of their ability to beneficially alter properties at low filler concentration, good interfacial bonding with polymer, availability in different forms, etc. The property alteration of polymer composites makes them versatile for applications in various fields, such as constructions, microelectronics, biomedical, and so on. Devastations due to building fire stress the importance of flame-retardant polymer composites, since they are directly related to human life conservation and safety. Thus, in this review, the significance of carbon-based flame-retardants for polymers is introduced. The effects of a wide variety of carbon-based material addition (such as fullerene, CNTs, graphene, graphite, and so on) on reaction-to-fire of the polymer composites are reviewed and the focus is dedicated to biochar-based reinforcements for use in flame retardant polymer composites. Additionally, the most widely used flammability measuring techniques for polymeric composites are presented. Finally, the key factors and different methods that are used for property enhancement are concluded and the scope for future work is discussed.

Polyethylene (PE) is one the most used plastics worldwide for a wide range of applications due to its good mechanical and chemical resistance, low density, cost efficiency, ease of processability, non-reactivity, low toxicity, good electric insulation, and good functionality. However, its high flammability and rapid flame spread pose dangers for certain applications. Therefore, different flame-retardant (FR) additives are incorporated into PE to increase its flame retardancy. In this review article, research papers from the past 10 years on the flame retardancy of PE systems are comprehensively reviewed and classified based on the additive sources. The FR additives are classified in well-known FR families, including phosphorous, melamine, nitrogen, inorganic hydroxides, boron, and silicon. The mechanism of fire retardance in each family is pinpointed. In addition to the efficiency of each FR in increasing the flame retardancy, its impact on the mechanical properties of the PE system is also discussed. Most of the FRs can decrease the heat release rate (HRR) of the PE products and simultaneously maintains the mechanical properties in appropriate ratios. Based on the literature, inorganic hydroxide seems to be used more in PE systems compared to other families. Finally, the role of nanotechnology for more efficient FR-PE systems is discussed and recommendations are given on implementing strategies that could help incorporate flame retardancy in the circular economy model.

The effect of thermochromic coatings of vanadium dioxide (VO2) on the fire performance of windows was experimentally tested. Prototypes were subjected to radiant heat and the radiation transmitted ...

The effect of pyrolysis reactors on the properties of biochars (with a focus on flammability and mechanical characteristics) were investigated by keeping factors such as feedstock, carbonisation temperature, heating rate and residence time constant. The reactors employed were hydrothermal, fixed-bed batch vertical and fixed-bed batch horizontal-tube reactors. The vertical and tube reactors, at the same temperature, produced biochars having comparable elemental carbon content, surface functionalities, thermal degradation pattern and peak heat release rates. The hydrothermal reactor, although, a low-temperature process, produced biochar with high fire resistance because the formed tarry volatiles sealed water inside the pores, which hindered combustion. However, the biochar from hydrothermal reactor had the lowest nanoindentation properties whereas the tube reactor-produced biochar at 300 °C had the highest nanoindentation-hardness (290 Megapascal) and modulus (ca. 4 Gigapascal) amongst the other tested samples. Based on the inherent flammability and mechanical properties of biochars, polymeric composites’ properties can be predicted that can include them as constituents.

Biocomposites being environmentally-friendly alternative to synthetic composites are gaining increasing demand for various applications. Hence, biocomposite development should be integrated within a circular economy (CE) model to ensure a sustainable production that is simultaneously innocuous towards the environment. This review presents an overview of the state-of-the-art technologies for the adoption of the CE concept in biocomposite development. The study outlined the properties, environmental and economic impacts of biocomposites. A critical review of the life-cycle assessment of biocomposite for evaluating greenhouse gas emissions and carbon footprints was conducted. In addition, the opportunities and challenges pertaining to the implementation of CE have been discussed in detail. Recycling and utilisation of bio-based constituents were identified as the critical factors in embracing CE. Therefore, the development of innovative recycling technologies and an enhanced use of novel biocomposite constituents could lead to a reduction in material waste and environmental footprints. This article is one of the first studies to review the circularity of biocomposites in detail that will stimulate further research in enhancing the sustainability of these polymeric materials.

The modelling of the behavior of a material exposed to fire is very complex and needs the coupling of fluid dynamics, combustion, heat and mass transfer, kinetics and so forth. A growing amount of ...

The work involves fabrication of natural fibre/Elium® composites using resin infusion technique. The jute fabrics were treated using phosphorus-carbon based flame retardant (FR) agent, a phosphonate solution and graphene nano-platelet (GnP), followed by resin infusion, to produce FR and graphene-based composites. The properties of these composites were compared with those of the Control (jute fabric/Elium®). As obtained from the cone calorimeter and Fourier transform infrared spectroscopy, the peak heat release rate reduced significantly after the FR and GnP treatments of fabrics whereas total smoke release and quantity of carbon monoxide increased with the incorporation of FR. The addition of GnP had almost no effect on carbon monoxide and carbon dioxide yield. Dynamic mechanical analysis demonstrated that coating jute fabrics with GnP particles led to an enhanced glass transition temperature by 14%. Scanning electron microscopy showed fibre pull-out locations in the tensile fracture surface of the laminates after incorporation of both fillers, which resulted in reduced tensile properties.

Phytic acid (PA) is one of the widely used flame retardants (FRs) to treat a variety of fabrics owing to its high phosphorus content of ca. 28 wt% (with respect to its molecular weight), abundance, non-toxicity, and biocompatibility. The current review discusses the state-of-the-art of PA-based FRs for natural fabrics such as cotton and wool. The possibilities of making PA and FR-based multi-functional cotton fabrics having antimicrobial, conductive, hydrophobic properties are reported by virtue of the synergistic benefits associated with chitosan, silicon, nitrogen, and boron-based molecules. The factors influencing the FR behaviour as well as the durability of PA-based cotton and wool fabrics are discussed with respect to the concentration of PA, pH of the coating solution, temperature, and preparation methods. Holistically, PA has been proved to be a potential alternative to halogenated FRs to confer fire retardant property to cotton and wool fabrics.

The issue of sustainability is a growing concern and has led to many environmentally friendly chemical productions through a great intensification of the use of biomass conversion processes. Thermal conversion of biomass is one of the most attractive tools currently used, and pyrolytic treatments represent the most flexible approach to biomass conversion. In this scenario, microwave-assisted pyrolysis could be a solid choice for the production of multi-chemical mixtures known as bio-oils. Bio-oils could represent a promising new source of high-value species ranging from bioactive chemicals to green solvents. In this review, we have summarized the most recent developments regarding bio-oil production through microwave-induced pyrolytic degradation of biomasses.

The global coronavirus disease 2019 (COVID‐19) pandemic has rapidly increased the demand for facemasks as a measure to reduce the rapid spread of the pathogen. Throughout the pandemic, some countries such as Italy had a monthly demand of ca. 90 million facemasks. Domestic mask manufacturers are capable of manufacturing 8 million masks each week, although the demand was 40 million per week during March 2020. This dramatic increase has contributed to a spike in the generation of facemask waste. Facemasks are often manufactured with synthetic materials that are non‐biodegradable, and their increased usage and improper disposal are raising environmental concerns. Consequently, there is a strong interest for developing biodegradable facemasks made with for example, renewable nanofibres. A range of natural polymer‐based nanofibres has been studied for their potential to be used in air filter applications. This review article examines potential natural polymer‐based nanofibres along with their filtration and antimicrobial capabilities for developing biodegradable facemask that will promote a cleaner production.

The onset of coronavirus pandemic has sparked a shortage of facemasks in almost all nations. Without this personal protective equipment, healthcare providers, essential workers, and the general public are exposed to the risk of infection. In light of the aforementioned, it is critical to balance the supply and demand for masks. COVID-19 will also ensure that masks are always considered as an essential commodity in future pandemic preparedness. Moreover, billions of facemasks are produced from petrochemicals derived raw materials, which are non-degradable upon disposal after their single use, thus causing environmental pollution and damage. The sustainable way forward is to utilise raw materials that are side-stream products of local industries to develop facemasks having equal or better efficiency than the conventional ones. In this regard, wheat gluten biopolymer, which is a by-product or co-product of cereal industries, can be electrospun into nanofibre membranes and subsequently carbonised at over 700 °C to form a network structure, which can simultaneously act as the filter media and reinforcement for gluten-based masks. In parallel, the same gluten material can be processed into cohesive thin films using plasticiser and hot press. Additionally, lanosol, a naturally-occurring substance, imparts fire (V-0 rating in vertical burn test), and microbe resistance in gluten plastics. Thus, thin films of flexible gluten with very low amounts of lanosol (, Graphical abstract The possible pathway to develop fully bio-based facemasks.Unlabelled Image, Highlights • Coronavirus pandemic have made facemasks worldwide healthcare essentials • Shortage of masks exposes medical personnel and the public to the risk of infection • Utilisation of sustainable raw materials to develop bio-based masks is needed • Electrospun and compression moulded gluten can be used to develop bio-based masks • Gluten masks can be made flame retardant by adding

Wire and cable coverings are potentially a major cause of fire in buildings and other installations. As they need to breach fire walls and are frequently located in vertical ducting, they have significant potential to increase the fire hazard. It is therefore important to understand the ignition and burning characteristics of cables by developing a model capable of predicting their burning behaviour for a range of scenarios. The fire performance of electrical cables is usually dominated by the fire performance of the sheathing materials. The complexity of the problem increases when cable sheathing incorporates fire retardants. One-dimensional pyrolysis models have been constructed for cable sheathing materials, based on milligram-scale and bench-scale test data by comparing the performance of three different software tools (ThermaKin, Comsol Multiphysics and FDS, version 6.0.1). Thermogravimetric analysis and differential scanning calorimetry were conducted on powdered cable coatings to determine the thermal degradation mechanism, the enthalpy of decomposition reactions, and the heat capacities of all apparent species. The emissivity and the in-depth absorption coefficient were determined using reflectance and transmittance measurements, with dispersive and non-dispersive spectrometers and integrating spheres. Bench-scale tests were conducted with a mass loss calorimeter flushed with nitrogen on samples in a horizontal orientation, for comparison with the pyrolysis model of non-flaming decomposition at an external heat flux of 50 kW m−2. The parameters determined through analysis of the milligram-scale data were used to construct a pyrolysis model that predicted the total mass loss from calorimeter tests in anaerobic conditions. A condensed phase pyrolysis model that accurately predicts in-depth temperature profiles of a solid fuel, and the mass flux of volatiles evolved during degradation of the fuel, is an essential component of a comprehensive fire model, which when coupled to a computational fluid dynamics code can be used to predict the burning processes in a fire scenario. Pyrolysis models vary considerably in complexity based on the assumptions incorporated into the development of the model.

EIT Raw Materials, one of the six Knowledge and Innovation Communities (KICs) initiated by the EIT (European Institute of Innovation and Technology) and funded by the European Commission, has the mission to boost competitiveness, growth and attractiveness of the European raw materials sector via radical innovation and guided entrepreneurship. It aims to significantly enhance innovation in the raw materials sector by the sharing of knowledge, information and expertise. This must generate a significant impact on European competitiveness and employment by driving and fostering innovation and empowering students, entrepreneurs and education partners driving toward the circular economy. To reach the vision, where the European Union’s industrial strength is based on a cost-efficient, secure, sustainable supply and use of raw materials, a new generation of skilled people entering industry, universities and research needs to be developed. Today’s technical MSc graduates in raw materials and especially primary resources (i.e. exploration, extraction, mining and mineral processing and metallurgy) meet the technical standards required by the raw materials industry across the full raw materials value chain and best suits large companies where they often act as specialists and experts. For small to medium enterprises as well as for our future engineers, other skills than technical are necessary. EIT Raw Materials will educate people that will have an intra- and entrepreneurial mind-set and will be able to develop their functions in new working environments, fostering the entrepreneurial and innovation skills, knowledge and attitudes needed for the entre- and intrapreneurs of tomorrow The CDIO™ INITIATIVE is an innovative educational framework for producing the next generation of engineers. The framework provides students with an education stressing engineering fundamentals set in the context of Conceiving — Designing — Implementing — Operating (CDIO) real-world systems and products. There are no academic institutes in Europe that have yet applied CDIO for primary resource related MSc programs. Within the KIC EIT Raw Materials Academy, the overarching brand of all the KIC’s education activities are created in order to stimulate education activities and foster new ways of learning and teaching; an approved education project is focusing on the implementation of the CDIO methodology in primary resources linked programs. The project started in 2016 and focuses on faculty and pilot case development and the contributing partners are from academia, industry and research institutes. This project focuses on faculty development for an active and experimental learning by teaching the “technical” faculty through CDIO linked courses (entrepreneurship, business, etc.), communicative workshops, inspiration lectures and by involving the “business and entrepreneurial” faculty in exploration, mining, mineral processing and metallurgy related issues also through curriculum and pilot cases developed together with the industry. This paper describes how this education project is being developed within the EIT Raw Materials and will give an overview of the needed skillset of future engineers demanded in the Raw Materials primary sector. It presents key outputs about already developed and implemented activities in mining engineering and metallurgy related programs.

In general it is recommended to fill a transformer pit with rock ballast to extinguish the fire if there is a leakage of burning transformer oil. There is a lack of technology-neutral performance requirements for the design of solutions for fire extinguishment in transformer pit fires. This hampers the introduction of alternatives to the traditional method of filling the pit with rocks. Therefore we have conducted quantitative tests where temperatures and concentrations of CO, CO2, and O2 were measured at different position in a transformer pit subjected to burning oil simulating an accidental rupture and leakage. The tests were conducted to investigate the extinguishing capacity of one specific alternative solution, i.e. a profile plank layer over the pit. Three tests were performed with 90°C and 140°C pre-heated transformer oil. In the second test, a 19 cm water bed was used to examine the impact of rain water in the pit. The result showed that the profile plank extinguished the flames in a few seconds and that the water level did not have any significant effect on the result. The measurements showed that the temperatures peaked at 600–800°C 50 cm above the profile plank in all tests but dropped to under 100°C in 14–16 s. Furthermore the O2-concentration dropped to 3–5 vol% below the plank, which contributed to the rapid extinction of the burning oil.

International audience; The radiation emission of the heating coil of a Cone Calorimeter and the one of the halogen lamp of a Fire Propagation Apparatus have been studied experimentally for varying power settings. These are two standard apparatuses used for fire calorimetry. The objective is to characterize and compare the radiative flux spectrum received by a fuel sample during pyrolysis experiments. The deviation from the standard assumption of black or gray emission is discussed. It is observed that the emission of the heating coil can be approximated well to an ideal blackbody, especially in the infrared range. On the contrary, the halogen lamp emission is more complex, non gray, with an important contribution in the visible and in the near infrared ranges. The flux received by a sample exposed to these emitters is predicted using ray tracing simulations. This shows that the irradiation flux and spectrum from the cone can be accurately calculated if the coil temperature is known. The non Lambertian irradiation flux from the lamp is modeled with a combination of diffuse and collimated intensities, representing the direct emission from the lamp itself and the reflection by the mirror at the rear side. For both emitters, the irradiation is confirmed to be approximately uniform over the surface of a sample 5 cm large (maximum deviation of ±2% on the incident flux). The uniformity decreases for larger samples, but the ratio of the flux at the center to average flux is still 1.04 for standard 10 cm × 10 cm samples under the cone. For illustration purposes, the influence of the spectral characteristics of the emitter is studied in the case of a sample of PMMA, a non gray translucent medium. Using recently published measurements of \PMMA\ absorptivity, the absorbed flux by a 3 cm thick sample is predicted. In the case of an incident flux of 20 kW/m2, the calculated average absorptivity of the sample is 0.91 under the cone, while it is 0.32 under the \FPA\ lamp. These calculations involve absorption data of a virgin sample at room temperature and consequently the numerical results only hold for the initial instants of irradiation. However, the very large differences in radiative behavior show that important discrepancies in the pyrolysis behavior are expected between the two emitters. This might have consequences for fire testing and inter comparisons of flammability results worth further investigation.

SUMMARY This work presents measurements meant to study the influence of the spark energy on the time to ignition of a given material in the cone calorimeter. For this purpose, square slabs of particle board were tested under two radiation intensities until ignition occurred using two spark energies for each intensity level. Results show that increasing the spark energy leads to a reduction in the ignition time regardless of the radiation intensity. However, the influence of the spark energy on the time to ignition is, in absolute numbers, larger for the low radiation intensity case than for the high radiation intensity case. Nonetheless, the proportional difference is nearly 10% for both levels of heat radiation. Results from this work confirm that there is an influence of the spark energy on the time to ignition of a given material suggesting that a narrower and more specific definition of the ignition circuits allowed in the cone calorimeter would be highly beneficial for ensuring repeatable results among laboratories. Copyright © 2013 John Wiley & Sons, Ltd.

The influence of additives on the interaction between radiation from fires and single water droplets has been investigated in detail. A literature study was performed on available information of radiation spectra from different types of fires. Based on this, four reference spectra were proposed that cover most of the different types of radiation that can be expected from fires. These reference spectra were used to compare the effect of different water additives and droplets sizes. Using Mie-theory it was found that increased atomization, down to a diameter limit of 1–10 μm, gives a better volumetric absorption efficiency. Decreasing the diameter further does not lead to improved volumetric absorption since the Rayleigh (small droplet) limit is reached, where the volumetric absorption is independent of diameter. Different additives were investigated with respect to increased absorption in the droplets. It was found, however, that it is not trivial to find non-flammable and non-toxic additives that give a significant improvement in absorption. Carbonated water was a potential candidate but the increased absorption was limited to a very weak band centered at 2300 cm −1 . Since this coincides with the strong CO 2 emission band an effect could be seen when carbonated water interacted with radiation from clean flames. The maximum increase in volumetric absorption for carbonated water was 4%, occurring for a droplet diameter of 10 μm. Other additives gave better effects but they were either combustible (carbon nanopowder) and/or toxic to some degree.

Two surface materials for reducing absorptivity of heat radiation from fires have been investigated. The first is VO2, which is a thermochromic material. When the temperature of a VO2 surface increases over a certain temperature, it switches, ideally, from infrared (IR)-absorbing to IR-reflecting. VO2 window coatings are still on a research level, yet to be commercialized. In this study, VO2 powder available on the market was investigated. The thermochromic effect could be identified but was not large enough to significantly improve the fire properties of treated surfaces. Some thoughts concerning how to improve the performance of VO2 are discussed. The second investigated material is indium tin oxide (ITO), which is a so called low-e coating, which means that it has low emissivity and absorptivity in the IR part of the spectrum. ITO is spectrally selective in the sense that it transmits visible light while reflecting a large fraction of the IR radiation, which is a rare property for surfaces in general but a typical property of thin electrically conducting non-metallic films. It is shown that the application of ITO to poly(methyl methacrylate) (PMMA) significantly improves its fire properties. ITO coating is a mature technology already in widespread use today in the electronics industry.

A comparative study of test methods for assessment of fire safety performance of bus interior materials

The spectral absorptivity of 62 products has been measured in the wavelength region of 0.3-20 mu m. Effective absorptivity for fire-induced heat radiation typically lies in the range of 0.75-0.95. It was found that the effective absorptivity varies significantly with the temperature of the heat source. This has implications on the heating of a surface. The effect is more important when the absorptivity is used as input for calculations of ignition temperature and thermal inertia. It was also found that the absorptivity of radiation from fires for products exposed to irradiation in many cases decreased with increased exposure time. This is surprising since, for example, wood that is darkened when exposed to heat obviously has a higher absorptivity in the visual part of the spectrum than fresh non-darkened wood. The reason that was identified for this is because the absorptivity in the IR drops, and measurement results are given which clearly illustrate this.

Mid-infrared polarization spectroscopy : A tool for in situ measurements of toxic gases in smoke-laden environments

Measurements of the ion current between two electrodes have been conducted in order to assess whether the ion current can be used for the detection of ignition in a cone calorimeter, and for fire dynamics investigations in general. The measured ion current clearly indicates when ignition occurs, in agreement with traditional results based on visual inspection. It was also seen that soot deposits on the electrodes do not adversely affect the ability of the ion current to indicate ignition. However, short circuiting may occur if the electrodes are kept in a sooty flame long enough for the soot to completely bridge the gap between the electrodes. The latter scenario is not a problem from an ignition detection point of view since soot growth occurs after ignition has taken place. Measurement of the ion current between the electrodes was also conducted in a premixed propane flame in order to characterize the dependence of the current on applied voltage and on combustion conditions. The ion current obeys Ohm's law since the current increases linearly with applied voltage in the investigated voltage range. It was also seen that the ion current gave unique results based on its position in a propane flame and the fuel/air ratio of the flame. Copyright © 2010 John Wiley & Sons, Ltd.

International audience; The pyrolysis of solid polymeric materials is a complex process that involves both chemical and physical phenomena such as phase transitions, chemical reactions, heat transfer, and mass transport of gaseous components. For modeling purposes, it is important to characterize and to quantify the properties driving those phenomena, especially in the case of flame-retarded materials. In this study, protocols have been developed to characterize the thermal conductivity and the heat capacity of an ethylene-vinyl acetate copolymer (EVA) flame retarded with aluminum tri-hydroxide (ATH). These properties were measured for the various species identified across the decomposition of the material. Namely, the thermal conductivity was found to decrease as a function of temperature before decomposition whereas the ceramic residue obtained after the decomposition at the steady state exhibits a thermal conductivity as low as 0.2 W/m/K. The heat capacity of the material was also investigated using both isothermal modulated Differential Scanning Calorimetry (DSC) and the standard method (ASTM E1269). It was shown that the final residue exhibits a similar behavior to alumina, which is consistent with the decomposition pathway of EVA/ATH. Besides, the two experimental approaches give similar results over the whole range of temperatures. Moreover, the optical properties before decomposition and the heat capacity of the decomposition gases were also analyzed. Those properties were then used as input data for a pyrolysis model in order to predict gasification experiments. Mass losses of gasification experiments were well predicted, thus validating the characterization of the thermo-physical properties of the material