Search

Squatting is a common daily activity and fundamental exercise in resistance training and closed kinetic chain programs. The aim of the present study was to investigate the effects of an experimentally induced weakness of the gluteal muscles on joint kinematics, reactions forces (JRFs), and dynamic balance performance during deep bilateral squats in healthy young adults. Ten healthy adults received sequential blocks of 1) branch of the superior gluteal nerve to the tensor fasciae latae (SGNtfl) muscle, 2) superior gluteal nerve (SGN), and 3) inferior gluteal nerve (IGN) on the dominant right leg. At the control condition and following each block, the participants were instructed to perform deep bilateral squats standing on two force plates. Hip, knee, ankle, and pelvis kinematics did not differ significantly following iatrogenic weakness of gluteal muscles. The most important finding was the significant differences in JRFs following SGN and IGN block, with the affected hip, patellofemoral, and ankle joint demonstrating lower JRFs, whereas the contralateral joints demonstrated significantly higher JRFs, especially the patellofemoral joint which demonstrated an average maximum difference of 1.43 x body weight compared to the control condition. When performing a deep bilateral leg squat under SGN and IGN block, the subjects demonstrated an increased center of pressure (CoP) range and standard deviation (SD) in mediolateral compared to the control condition. These results imply that squat performance changes significantly following weakness of gluteal muscles and should be considered when assessing and training athletes or patients with these injuries. This article is protected by copyright. All rights reserved.

PURPOSE Intraoperative hinge fractures in distal femur osteotomies represent a risk factor for loss of alignment and non-union. Using finite element analysis, the goal of this study was to investigate the influence of different hinge widths and osteotomy corrections on hinge fractures in medial closed-wedge and lateral open-wedge distal femur osteotomies. METHODS The hinge was located at the proximal margin of adductor tubercle for biplanar lateral open-wedge and at the upper border of the lateral femoral condyle for biplanar medial closed-wedge distal femur osteotomies, corresponding to optimal hinge positions described in literature. Different hinge widths (5, 7.5, 10 mm) were created and the osteotomy correction was opened/closed by 5, 7.5 and 10 mm. Tensile and compressive strain of the hinge was determined in a finite element analysis and compared to the ultimate strain of cortical bone to assess the hinge fracture risk. RESULTS Doubling the correction from 5 to 10 mm increased mean tensile and compressive strain by 50% for lateral open-wedge and 48% for medial closed-wedge osteotomies. A hinge width of 10 mm versus 5 mm showed increased strain in the hinge region of 61% for lateral open-wedge and 32% for medial closed-wedge osteotomies. Medial closed-wedge recorded a higher fracture risk compared to lateral open-wedge osteotomies due to a larger hinge cross-section area (60-67%) for all tested configurations. In case of a 5 mm hinge, medial closed-wedge recorded 71% higher strain in the hinge region compared to lateral open-wedge osteotomies. CONCLUSION Due to morphological features of the medial femoral condyle, finite element analysis suggests that lateral-open wedge osteotomies are the preferable option if larger corrections are intended, as a thicker hinge can remain without an increased hinge fracture risk.

PURPOSE Functional internal rotation (IR) is a combination of extension and IR. It is clinically often limited after reverse total shoulder arthroplasty (RTSA) either due to loss of extension or IR in extension. It was the purpose of this study to determine the ideal in-vitro combination of glenoid and humeral components to achieve impingement-free functional IR. METHODS RTSA components were virtually implanted into a normal scapula (previously established with a statistical shape model) and into a corresponding humerus using a computer planning program (CASPA). Baseline glenoid configuration consisted of a 28 mm baseplate placed flush with the posteroinferior glenoid rim, a baseplate inclination angle of 96° (relative to the supraspinatus fossa) and a 36 mm standard glenosphere. Baseline humeral configuration consisted of a 12 mm humeral stem, a metaphysis with a neck shaft angle (NSA) of 155° (+ 6 mm medial offset), anatomic torsion of -20° and a symmetric PE inlay (36mmx0mm). Additional configurations with different humeral torsion (-20°, + 10°), NSA (135°, 145°, 155°), baseplate position, diameter, lateralization and inclination were tested. Glenohumeral extension of 5, 10, 20, and 40° was performed first, followed by IR of 20, 40, and 60° with the arm in extension of 40°-the value previously identified as necessary for satisfactory clinical functional IR. The different component combinations were taken through simulated ROM and the impingement volume (mm$^{3}$) was recorded. Furthermore, the occurrence of impingement was read out in 5° motion increments. RESULTS In all cases where impingement occurred, it occurred between the PE inlay and the posterior glenoid rim. Only in 11 of 36 combinations full functional IR was possible without impingement. Anterosuperior baseplate positioning showed the highest impingement volume with every combination of NSA and torsion. A posteroinferiorly positioned 26 mm baseplate resulting in an additional 2 mm of inferior overhang