Search

Barium ferrite in constant amount (50 phr) was incorporated into styrene-butadiene rubber to prepare rubber magnetic composites. Dicumyl peroxide was used as a curing agent for cross-linking of the prepared composites. Four different types of low-molecular-weight organic compounds were applied as coagents to enhance the efficiency of cross-linking process and to improve the compatibility between the rubber and the filler on the interphase. The main goal of this work was to investigate the influence of the composition of peroxide curing system on cross-link density, physical–mechanical and magnetic properties of the composites. The results revealed that the type and amount of coagents have no influence on magnetic properties of the rubber magnets. On the other hand, cross-link density and physical–mechanical properties were significantly dependent on the composition of curing system. The increase of tensile strength can be attributed to the improvement of adhesion on the interphase filler–rubber due to the presence of coagents. [ABSTRACT FROM AUTHOR]

Rubber magnetic composites were prepared by incorporation of barium ferrite in constant amount—50 phr into acrylonitrile-butadiene rubber. Dicumyl peroxide as the curing agent was used for cross-linking of rubber magnets alone, or in combination with four different types of co-agents. The main aim was to examine the influence of curing system composition on magnetic and physical-mechanical properties of composites. The cross-link density and the structure of the formed cross-links were investigated too. The results demonstrated that the type and amount of the co-agent had significant influence on cross-link density, which was reflected in typical change of physical-mechanical properties. The tensile strength increased with increasing amount of co-agents, which can be attributed to the improvement of adhesion and compatibility on the interphase filler-rubber due to the presence of co-agents. Magnetic characteristics were found not to be influenced by the curing system composition. The application of peroxide curing systems consisting of organic peroxide and co-agents leads to the preparation of rubber magnets with not only good magnetic properties but also with improved physical-mechanical properties, which could broaden the sphere of their application uses. [ABSTRACT FROM AUTHOR]

In order to make bioplastics accessible for a wider spectrum of applications, ready-to-use plastic material formulations should be available with tailored properties. Ideally, these kinds of materials should also be "home-compostable" to simplify their organic recycling. Therefore, materials based on PLA (polylactid acid) and PHB (polyhydroxybutyrate) blends are presented which contain suitable additives, and some of them contain also thermoplastic starch as a filler, which decreases the price of the final compound. They are intended for various applications, as documented by products made out of them. The produced materials are fully biodegradable under industrial composting conditions. Surprisingly, some of the materials, even those which contain more PLA than PHB, are also fully biodegradable under home-composting conditions within a period of about six months. Experiments made under laboratory conditions were supported with data obtained from a kitchen waste pilot composter and from municipal composting plant experiments. Material properties, environmental conditions, and microbiology data were recorded during some of these experiments to document the biodegradation process and changes on the surface and inside the materials on a molecular level. [ABSTRACT FROM AUTHOR]

This study focused on material recycling of a biodegradable blend based on PLA and PHB for multiple applications of biodegradable polymeric material under real conditions. In this study, we investigated the effect of multiple processing of a biodegradable polymer blend under the trade name NONOILEN®, which was processed under laboratory as well as industrial conditions. In this article, we report on testing the effect of blending and multiple processing on thermomechanical stability, molecular characteristics, as well as thermophysical and mechanical properties of experimental- and industrial-type tested material suitable for FDM 3D technology. The results showed that the studied material degraded during blending and subsequently during multiple processing. Even after partial degradation, which was demonstrated by a decrease in average molecular weight and a decrease in complex viscosity in the process of multiple reprocessing, there was no significant change in the material's thermophysical properties, either in laboratory or industrial conditions. There was also no negative impact on the strength characteristics of multiple processed samples. The results of this work show that a biodegradable polymer blend based on PLA and PHB is a suitable candidate for material recycling even in industrial processing conditions. In addition, the results suggest that the biodegradable polymeric material NONOILEN® 3D 3056-2 is suitable for multiple uses in FDM technology. [ABSTRACT FROM AUTHOR]

The study is focused on modelling the evaluation of recyclability of the biodegradable blend using multiple extrusion of selected composition of PLA/PHB blend which had been more deeply studied before. It was shown that the multiple extrusion reduces viscosity of the tested blend due to multiple thermomechanical stresses and the material was partially degraded. Partial degradation was demonstrated by measuring of molecular characteristics. The degree of degradation of the tested material was determined with relatively high accuracy after creating a colour space/viscosity. Multiple processing and subsequent degradation of the tested material did not negatively affect thermal properties, as well as strength characteristics of the blend. It was concluded that the biodegradable polymer blend of the PLA/PHB type is suitable for multiple processing and material recycling can be applied for this type of bioplastics. • Degradation of biodegradable polymer blend during processing. • Possibility of multiple processing of biodegradable polymer blends based on PLA a PHB. • Influence of degradation on thermal properties of PLA/PHB blends. • Influence of degradation on mechanical properties of PLA/PHB blends. • Possibility of recycling of PLA/PHB biodegradable polymer blends. [ABSTRACT FROM AUTHOR]