Search

In this study, we have compared magnetic and magnetostrictive properties of polycrystalline CoFe$_2$O$_4$ pellets, produced by three different methods, focusing on the use of Spark Plasma Sintering (SPS). This technique allows a very short heat treatment stage while a uniaxial pressure is applied. SPS was utilized to sinter cobalt ferrite but also to make the reaction and the sintering (reactive sintering) of the same ceramic composition. Magnetic and magnetostrictive measurements show that the reactive sintering with SPS induces a uniaxial anisotropy, while it is not the case with a simple sintering process. The induced anisotropy is then expected to be a consequence of the reaction under uniaxial pressure. This anisotropy enhanced the magnetostrictive properties of the sample, where a maximum longitudinal magnetostriction of $-229$~ppm is obtained. This process can be a promising alternative to the magnetic-annealing because of the short processing time required (22 minutes).

In this paper, we investigate the demagnetizing effect in ferrite/PZT/ferrite magnetoelectric (ME) trilayer composites consisting of commercial PZT discs bonded by epoxy layers to Ni-Co-Zn ferrite discs made by a reactive Spark Plasma Sintering (SPS) technique. ME voltage coefficients (transversal mode) were measured on ferrite/PZT/ferrite trilayer ME samples with different thicknesses or phase volume ratio in order to highlight the influence of the magnetic field penetration governed by these geometrical parameters. Experimental ME coefficients and voltages were compared to analytical calculations using a quasi-static model. Theoretical demagnetizing factors of two magnetic discs that interact together in parallel magnetic structures were derived from an analytical calculation based on a superposition method. These factors were introduced in ME voltage calculations which take account of the demagnetizing effect. To fit the experimental results, a mechanical coupling factor was also introduced in the theoretical formula. This reflects the differential strain that exists in the ferrite and PZT layers due to shear effects near the edge of the ME samples and within the bonding epoxy layers. From this study, an optimization in magnitude of the ME voltage is obtained. Lastly, an analytical calculation of demagnetizing effect was conducted for layered ME composites containing higher numbers of alternated layers (). The advantage of such a structure is then discussed.

We have investigated the magnetoelectric (ME) effect in layered composite rings subjected to circumferential AC magnetic fields and DC magnetic fields in radial, axial or circumferential directions. Bilayer samples were obtained combining different grades of commercial Mn-Zn ferrites or Ni-Zn ferrites with commercial lead zirconate titanate (PZT). Mn-Zn ferrites with low magnetostriction saturation () and low magneto-crystalline anisotropy constants show high ME capabilities when associated with PZT in ring structures. In certain conditions, these ME effects are higher than those obtained with Terfenol-D/PZT composites in the same layered ring structure. Magnetostrictive and mechanical characterizations have given results that explain these high ME performances. Nevertheless, Mn-Zn ferrite/PZT composites exhibit voltages responses with low linearity especially at high signal level. Based on the particular structure of the ME device, a method to decrease the nonlinear harmonic distortion of the ME voltages is proposed. Harmonic distortion analysis of ME voltages measured in different configurations allows us to explain the phenomenon.

We report the use of high magnetomechanical coupling ferrites in magnetoelectric (ME) layered composites. Bilayer samples combining $(Ni_{0.973} Co_{0.027})_{1-x} Zn_x Fe_2 O_4$ ferrites ($x = 0-0.5$) synthesized by non conventional reactive Spark Plasma Sintering and commercial lead zirconate titanate (PZT) were characterized in term of ME voltage coefficients measured at sub-resonant frequency. Strong ME effects are obtained and we show that an annealing at 1000$^\circ$C and a quenching in air improve the piezomagnetic behavior of Zn-rich compositions. A theoretical model that predicts the ME behavior was developed, focusing our work on the demagnetizing effects in the transversal mode as well as the longitudinal mode. The model shows that: (i) high ME coefficients are obtained when ferrites with high magnetomechanical coupling are used in bilayer ME composites, (ii) the ME behavior in transversal and longitudinal modes is quite similar, and differences in the shapes of the ME curves are mainly due the demagnetizing effects, (iii) in the transversal mode, the magnetic field penetration depends on the ferrite layer thickness and the ME coefficient is affected accordingly. The two later points are confirmed by measurements on ME samples and calculations. Performances of the ME composites made with high magnetomechanical coupling ferrites are compared to those obtained using Terfenol-D materials in the same conditions of size, shape, and volume ratio. It appears that a ferrite with an optimized composition has performances comparable to those obtained with Terfenol-D material. Nevertheless, the fabrication processes of ferrites are quite simpler. Finally, a ferrite/PZT based ME composite was used as a current sensor.

Microwave assisted magnetization reversal are studied in the bulk bilayer exchange coupled system. We investigate the nonlinear magnetization reversal dynamics in a perpendicular exchange spring media using Landau-Lifshitz equation. In the limit of the infinite thickness of the system, the propagation field leads the reversal of the system. The reduction of the switching field and the magnetization profile in the extended system are studied numerically. The possibility to study the dynamics analytically is discussed and an approximation where two P-modes are coupled by an interaction field is presented. The ansatz used for the interaction field is validated by comparison with the numerical results. This approach is shown to be equivalent to two exchange coupled macrospins.

In view of potential applications of magnetic particles in biomedicine and electromagnetic devices, we made use of the classical Stober method base-catalysed hydrolysis and condensation of tetraethoxysilane (TEOS) to encapsulate FeNi nanoparticles within a silica shell. An original stirring system under high power ultrasounds made possible to disperse the otherwise agglomerated particles. Sonication guaranteed particles to remain dispersed during the Stober synthesis and also improved the efficiency of the method. The coated particles are characterized by electron microscopy (TEM) and spectroscopy (EDX) showing a core-shell structure with a uniform layer of silica. Silica-coating does not affect the core magnetic properties. Indeed, all samples are ferromagnetic at 77 K and room temperature and the Curie point remains unchanged. Only the coercive force shows an unexpected non-monotonous dependence on silica layer thickness., Comment: Regular paper submited to international peer-reveiwed journal