Search

Vanadium is considered a strategic metal with wide applications in various industries due to its unique chemical and physical properties. On the basis of these considerations, the recovery of vanadium (V) is mandatory because of the lack of raw materials. Various methods are used to recover vanadium (V) from used aqueous solutions. This study develops a clean and effective process for the recovery of vanadium (V) by using the adsorption method. At the same time, this study synthesizes a material starting from silica matrices and iron oxides, which is used as an adsorbent material. To show the phase composition, the obtained material is characterized by X-ray diffraction showing that the material is present in the amorphous phase, with a crystal size of 20 nm. However, the morphological texture of the material is determined by the N 2 adsorption-desorption method, proving that the adsorbent material has a high surface area of 305 m 2 /g with a total pore volume of 1.55 cm 3 /g. To determine the efficiency of the SiO 2 Fe x O y material for the recovery of vanadium through the adsorption process, the role of specific parameters, such as the L-to-V ratio, pH, contact time, temperature, and initial vanadium concentration, must be evaluated. The adsorption process mechanism was established through kinetic, thermodynamic, and equilibrium studies. In our case, the process is physical, endothermic, spontaneous, and takes place at the interface of SiO 2 Fe x O y with V 2 O 5 . Following equilibrium studies, the maximum adsorption capacity of the SiO 2 Fe x O y material was 58.8 mg (V)/g of material.

The antibacterial activity of zinc oxide particles has received significant interest worldwide, especially through the implementation of technology to synthesize particles in the nanometer range. This study aimed to determine the antimicrobial efficacy of silica-based iron oxide matrix (SiO 2 Fe x O y ) synthesized with various amounts of ZnO (SiO 2 Fe x O y ZnO) against various pathogens. It is observed that, with the addition of ZnO to the system, the average size of the porosity of the material increases, showing increasingly effective antibacterial properties. Zinc-iron-silica oxide matrix composites were synthesized using the sol-gel method. The synthesized materials were investigated physicochemically to highlight their structural properties, through scanning electron microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDX), and Fourier-transform infrared spectroscopy (FT-IR). At the same time, surface area, pore size and total pore volume were determined for materials synthesized using the Brunauer-Emmett-Teller (BET) method. Although the material with 0.0001 g ZnO (600 m 2 /g) has the highest specific surface area, the best antimicrobial activity was obtained for the material with 1.0 g ZnO, when the average pore volume is the largest (~8 nm) for a specific surface of 306 m 2 /g. This indicates that the main role in the antibacterial effect has reactive oxygen species (ROS) generated by the ZnO that are located in the pores of the composite materials. The point of zero charge (pH pZc ) is a very important parameter for the characterization of materials that indicate the acid-base behaviour. The pH pZc value varies between 4.9 and 6.3 and is influenced by the amount of ZnO with which the iron-silica oxide matrix is doped. From the antimicrobial studies carried out, it was found that for S. aureus the total antibacterial effect was obtained at the amount of 1.0 g ZnO. For Gram-negative bacteria, a total antibacterial effect was observed in S. flexneri (for the material with 0.1 g ZnO), followed by E. coli (for 1.0 g ZnO). For P. aeruginosa , the maximum inhibition rate obtained for the material with 1.0 g ZnO was approximately 49%.

Aggressive industrial development over the last century involved different heavy metals being used, including high quantities of molybdenum, which need to be treated before discharge in industrial waters. Molybdenum's market price and industrial applicability make its recovery a big challenge. In the present study the possibility to recover molybdenum ions from aqueous solutions by adsorption on a composite material based on silica matrix and iron oxides-SiO 2 FexOy-was evaluated. Tests were performed in order to determine the influence of adsorbent material dose, initial solution pH, contact time and temperature over adsorption capacity of synthesized adsorbent material. For better understanding of the adsorption process, the obtained experimental data were modelled using Langmuir, Freundlich and Sips adsorption isotherms. Based on the obtained data, it can proved that the Sips isotherm was describing with better orderliness the studied process, obtaining a maximum adsorption capacity of 10.95 mg MoO42- for each gram of material. By modelling the studied adsorption process, it was proven that the pseudo-second order model is accurately describing the adsorption process. By fitting experimental data with Weber-Morris model, it was proven that MoO42- adsorption is a complex process, occurring in two different steps, one controlled by diffusion and the second one controlled by mass transfer. Further, studies were performed in order to determine the optimum pH value needed to obtain maximum adsorption capacity, but also to determine which are the adsorbed species. From pH and desorption studies, it was proven that molybdate adsorption is a physical process. In order to establish the adsorption mechanism, the thermodynamic parameters (ΔG0, ΔH0 and ΔS0) were determined.