Search

Much scientific equipment requires the use of humidity control technologies. This includes instruments with hygroscopic optics, such as infrared spectrometers, OPOs and some lasers. The most common strategies include nitrogen purging or desiccant bag replacement, which involve maintenance and running costs. In this work we present a dual strategy, combining both ionic membranes and silica desiccant, which results in a reusable and maintenance-free scheme for humidity control. The desiccant action of the silica gels, the membrane, and combinations thereafter, are studied. It is shown that the combination of the silica gel desiccants and the membrane is the most efficient configuration, reducing the humidity from 73% to only 15% in 20 h in a 70 L volume and from 80% to 20% in 40 h in a 230 L volume. An experiment over 5 days showed that the status of the silica gel desiccants that had adsorbed high water vapor levels returned to normal after they were enclosed together with the ionic membrane in the 70 L volume. Finally, measurements taken by a commercial infrared spectrometer of the reduction in the H2O lines absorption in the mid-infrared region under the operation of the combined configuration are examined. It was demonstrated that H2O lines with low to moderate absorption almost disappeared when the humidity levels inside the spectrometer dropped from 42.5% to 15.1% in the span of 90 min, while lines with stronger absorption remained present even though they showed the highest percentage of change. [ABSTRACT FROM AUTHOR]

In this work, the unique optical properties of surface plasmon polaritons (SPPs), i.e. subwavelength confinement or strong electric field concentration, are exploited to demonstrate the propagation of light signal at 600 nm along distances in the range from 17 to 150 μm for Au nanostripes 500 nm down to 100 nm wide (30 nm of height), respectively, both theoretically and experimentally. A low power laser is coupled into an optical fiber tip that is used to locally excite the photoluminescence of colloidal quantum dots (QDs) dispersed in their surroundings. Emitted light from these QDs is generating the SPPs that propagate along the metal waveguides. Then, the above-referred propagation lengths were directly extracted from this novel experimental technique by studying the intensity of light decoupled at the output edge of the waveguide. Furthermore, an enhancement of the propagation length up to 0.4 mm is measured for the 500-nm-wide metal nanostripe, for which this effect is maximum. For this purpose, a simultaneous excitation of the same QDs dispersed in poly(methyl methacrylate) waveguides integrated with the metal nanostructures is performed by end-fire coupling an excitation laser energy as low as 1 KW/cm2. The proposed mechanism to explain such enhancement is a non-linear interference effect between dielectric and plasmonic (super)modes propagating in the metal-dielectric structure, which can be apparently seen as an effective amplification or compensation effect of the gain material (QDs) over the SPPs, as previously reported in literature. The proposed system and the method to create propagating SPPs in metal waveguides can be of interest for the application field of sensors and optical communications at visible wavelengths, among other applications, using plasmonic interconnects to reduce the dimensions of photonic chips.

Photopolymer resins used in stereolithographic 3D printing are limited to penetration depths of less than 1 mm. Our approach explores the use of near-infrared (NIR) to visible upconversion (UC) emissions from lanthanide-based phosphors to initiate photopolymer crosslinking at a much higher depth. This concept relies on the use of invisibility windows and non-linear optical effects to achieve selective crosslinking in photopolymers. SLA resin formulation capable of absorbing light in the visible region (420–550 nm) was developed, in order to take advantage of efficient green-UC of Er3+/Yb3+ doped phosphor. NIR-green light UC shows versatility in enhancing curing depths in laser patterning. For instance, a structure with a curing depth of 11 ± 0.2 mm, cured width of 496 ± 5 µm and aspect ratios of over 22.2:1 in a single pass via NIR-green light UC. The penetration depth of the reported formulation approached 39 mm. Therefore, this technique would allow curing depths of up to 4 cm. Moreover, it was also demonstrated that this technique can initiate cross-linking directly at the focal point. This shows the potential of NIR-assisted UC as a low-cost method for direct laser writing in volume and 3D printing. [ABSTRACT FROM AUTHOR]