Search

It is widely recognized that the accuracy of explicit finite element simulations is sensitive to the choice of interface parameters (i.e. contact stiffness/damping, mesh generation, etc.) and time step sizes. Yet, the effect of these interface parameters on the explicit finite element based solutions of wheel-rail interaction has not been discussed sufficiently in literature. In this paper, the relation between interface parameters and the accuracy of contact solutions is studied. It shows that the wrong choice of these parameters, such as too high/low contact stiffness, coarse mesh, or wrong combination of them, can negatively affect the solution of wheel-rail interactions which manifest in the amplification of contact forces and/or inaccurate contact responses (here called ''contact instability''). The phenomena of ''contact (in)stabilities'' are studied using an explicit finite element model of a wheel rolling over a rail. The accuracy of contact solutions is assessed by analyzing the area of contact patches and the distribution of normal pressure. Also, the guidelines for selections of optimum interface parameters, which guarantee the contact stability and therefore provide an accurate solution, are proposed. The effectiveness of the selected interface parameters is demonstrated through a series of simulations. The results of these simulations are presented and discussed. [ABSTRACT FROM AUTHOR]

Transition zones in railway tracks are the locations with considerable changes in the vertical support structures. Due to the differential stiffness and settlement in the open track and the engineering structure resulting in the dynamic amplification of the wheel forces, track settlement is usually observed in the approaching zones. The settlement in transition zones is detrimental to the track components and passenger comfort. This paper presents the results of the experimental analysis performed in three transition zones which were in various conditions. The dynamic displacements of rails due to passing trains were measured at multiple points (dynamic profile) in the approaching zones. The device employed is a contactless mobile device for measuring displacements, which is based on the digital image correlation technique. Because the operational parameters of the digital image correlation-based devices are important for measurement accuracy, prior to the in situ measurements, this device was tested in a laboratory to study the influence of the operational parameters, including the elevation/heading angles, the focal length of the cameras, and the measuring distance. After determining the optimal operational parameters for the railway field, multiple-point measurements were performed in the transition zones. The length of the approaching zone was studied first. Also, the dynamic profiles of the embankment-bridge and bridge-embankment transitions were analysed. Finally, by comparing the multiple-point displacements in the approaching zones in different conditions, it was found that the dynamic profile of the rail displacements has a good correlation with the track condition in the transition zone. The results are presented and discussed. [ABSTRACT FROM AUTHOR]

Over the past few years, a number of implicit/explicit finite element models have been introduced for the purpose of tackling the problems of wheel-rail interaction. Yet, most of those finite element models encounter common numerical difficulties. For instance, initial gaps/penetrations between two contact bodies, which easily occur when realistic wheel- rail profiles are accounted for, would trigger the problems of divergence in implicit finite element simulations. Also, redundant, insufficient or mismatched mesh refinements in the vicinity of areas in contact can lead to either prohibitive calculation expenses or inaccurate implicit/explicit finite element solutions. To address the abovementioned problems and to improve the performance of finite element simulations, a novel modelling strategy has been proposed. In this strategy, the three-dimensional explicit finite element analysis is seamlessly coupled with the two-dimensional geometrical contact analysis. The contact properties in the three-dimensional finite element analyses, such as the initial ''Just-incontact'' point, the exact wheel local rolling radius, etc., which are usually a priori unknown, are determined using the two-dimensional geometrical contact model. As part of the coupling strategy, a technique has been developed for adaptive mesh refinement. The mesh and mesh density of wheel-rail finite element models change adaptively depending on the exact location of the contact areas and the local geometry of contact bodies. By this means, a good balance between the calculation efficiency and accuracy can be achieved. Last, but not least, the advantage of the coupling strategy has been demonstrated in studies on the relationship between the initial slips and the steady frictional rolling state. Finally, the results of the simulations are presented and discussed. [ABSTRACT FROM AUTHOR]

In this paper, the effects of repair welding and grinding, which are currently the main components used in the maintenance of crossings, on the performance of crossings are analyzed. It has been observed that sometimes the welding and grinding activities that directly affect the geometry of the crossings and/or material properties can have negative effects on the performance and ultimately on the service life of the crossings. In this paper, the effect of the changes of geometry has been studied experimentally, while the effect of the changes in the material properties has been analyzed using a numerical model. When grinding the shape of the crossing nose, the resulting profile can deviate from the original one. To analyze the geometry-related effects of welding and grinding, the geometry of crossings (cross-sectional profiles) as well as the corresponding dynamic accelerations due to passing trains are measured before and after the welding and grinding activities. Based on the comparison of the measured accelerations, the performance of the measured crossings has been assessed. Also, a welding repair that is not properly performed can lead to undesirable changes in the material properties of the rails, resulting in defects in rails. The material-related effects of the welding and grinding are studied using the three-dimensional explicit finite element model wherein a wheelset moves over a railway crossing. To understand the microstructure of the welding defect and provide an input for the numerical model, the results of ultrasonic and microscopic analyses of some welded crossings are presented first. Then, a number of the numerical simulations of the crossing with the welding defect are performed to investigate the failure mechanism of the crossing. Furthermore, assessment using the fatigue model (coupled with the finite element model) that accounts for the ratcheting behavior of material by calculating a number of the load cycles to the crack initiation is performed. Finally, conclusions on the effects of changes in geometry and material of the crossings due to repair welding and grinding are given. [ABSTRACT FROM AUTHOR]

Transition zones in railway tracks are the locations with considerable changes in vertical support structures, e.g., near bridges. Due to possible water flow constrictions in transition zone structures, there is frequently an increased moisture level in the ballast/subballast layers, which is a potential source of track degradation. This paper presents results of the moisture condition measured in three transition zones using ground penetrating radar, where the ballast/subballast are analyzed. The relationship between the moisture condition and track degradation in the transition zones is studied by comparing it to the longitudinal track level that is measured by the track inspection coaches. A strong connection is found between the high moisture condition and track degradation in the transition zones. The dynamic behavior of the transition zones with high moisture condition is analyzed using the Finite Element method. Differential stiffness and settlement are taken into consideration in the transition zone model, which is also coupled with a vehicle. The ballast/subballast layers are modelled as solid elements. Increased moisture conditions are considered as a reduction of elastic modulus, according to laboratory findings. Results show that high moisture leads to an increase of dynamic wheel loads in the transition zone, which explains the connection and confirms that the high moisture condition is a source of transition zone problems. [ABSTRACT FROM AUTHOR]