Search

Here we report the rational development of a carbon dot (CDs)-based fluorescent pH nanosensor by employing an active surface preservation strategy. More specifically, citric acid, urea and fluorescein were subjected to a one-pot hydrothermal treatment, which preserved fluorescein-like structures on the surface of the CDs. The obtained CDs showed pH-sensitive green emission, which can be used to determine pH variations from 3.7 to 12.1 by fluorescence enhancement. Moreover, the obtained nanoparticles showed excellent selectivity toward pH, fluorescence reversibility in different pH values, photostability, while being compatible with human cell lines (even at high concentrations). Furthermore, their performance as pH sensors was comparable with reference pH determination procedures. Thus, an active surface preservation strategy was successfully employed to develop fluorescence pH nanosensors in a rational manner and without post-synthesis functionalization strategies, which show potential for future use in pH determination.

In our study, we demonstrated the performance of antimicrobial coatings on properly functionalized and nanostructured 316L food-grade stainless steel pipelines. For the fabrication of these functional coatings, we employed facile and low-cost electrochemical techniques and surface modification processes. The development of a nanoporous structure on the 316L stainless steel surface was performed by following an electropolishing process in an electrolytic bath, at a constant anodic voltage of 40 V for 10 min, while the temperature was maintained between 0 and 10 °C. Subsequently, we incorporated on this nanostructure additional coatings with antimicrobial and bactericide properties, such as Ag nanoparticles, Ag films, or TiO2 thin layers. These functional coatings were grown on the nanostructured substrate by following electroless process, electrochemical deposition, and atomic layer deposition (ALD) techniques. Then, we analyzed the antimicrobial efficiency of these functionalized materials against different biofilms types (Candida parapsilosis, Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus, and Staphylococcus epidermidis). The results of the present study demonstrate that the nanostructuring and surface functionalization processes constitute a promising route to fabricate novel functional materials exhibiting highly efficient antimicrobial features. In fact, we have shown that our use of an appropriated association of TiO2 layer and Ag nanoparticle coatings over the nanostructured 316L stainless steel exhibited an excellent antimicrobial behavior for all biofilms examined.

Abstract The industrialization of perovskite solar cells requires adequate materials and processes to make them economically viable and environmentally sustainable. Despite promising results in terms of power conversion efficiency and operational stability, several hole‐transport layers currently in use still need to prove their industrial feasibility. This work demonstrates the use of nanocrystalline nickel oxide produced through flash infrared annealing (FIRA), considerably reducing the materials cost, production time, energy, and the amount of solvents required for the hole transport layer. X‐ray photoelectron spectroscopy reveals a better conversion to nickel oxide and a higher oxygen‐to‐nickel ratio for the FIRA films as compared to control annealing methods, resulting in higher device efficiency and operational stability. Planar inverted solar cells produced with triple cation perovskite absorber result in 16.7% power conversion efficiency for 1 cm2 devices, and 15.9% averaged over an area of 17 cm2.

Changes in the physicochemical characteristics of a regenerated cellulose (RC) film due to a surface modification with room-temperature ionic liquids (ILs) are determined. Two ILs (1-butyl-3-metylimidazolium hexafluorophosphate and tricaprylmethylammonium chloride) were selected, and film surface modification was performed by a dip-coating process (1 h) in the corresponding IL. The surface characterization of the RC/IL films was carried out by XPS at various take-off angles (from 15° to 75°), while the modification of mechanical properties was established by tensile analysis, obtaining a significant increase for the Young modulus of both RC/IL films when compared with the RC-support. Optical characteristics of the RC/IL films were determined by transmittance and reflectance measurements for wavelengths covering visible and near-infrared regions, while impedance spectroscopy (IS) measurements allow us to estimate the electrical changes in the RC/IL films. These results show the high transmittance of both RC/IL films (>90%) with slight differences depending on the IL in both optical regions, while the IS data analysis indicated a conductivity reduction and dielectric constant increase in the dielectric constant for both eco-friendly RC/IL films.

Surface characterization of polymer inclusion membranes (PIMs) using the polymers cellulose triacetate and polyvinyl chloride, containing different ionic liquids (ILs) as carriers, has been performed. Three different ILs have been tested: commercial trioctyl methylammonium chloride (Aliquat 336–AlqCl−) and two derivatives bearing the counter anion NO3− or SCN− (AlqNO3 and AlqSCN, respectively). Surface analysis was performed by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) for both dry membranes and PIMs immersed for 4 days in ultrapure water to investigate the effect of the interaction of water with the membrane’s morphology and composition. XPS analysis of the PIMs revealed that immersion in ultrapure water causes a decrease in the atomic concentration percentage (A.C.%) of the specific IL atoms (Cl, S, and N) when compared with dry samples. Moreover, SEM images of the PIMs containing the IL AlqNO3 showed an alteration in the morphology of the membrane due to water contact at surface level, whereas no changes were observed at a bulk level. These changes in the surface composition of the water equilibrated PIMs may be associated with the solubilization of the IL in the water solution, which, therefore, may affect the reactivity of the membrane’s surface. To better understand this effect, PIMs containing both AlqCl and AlqNO3 as carriers were used for arsenic (V) transport. It was found that AlqCl was the most effective IL and that the effectivity of the PIM on As(V) removal was not affected after five cycles of the membrane’s reuse.

Surface and bulk changes in a Nafion membrane as a result of IL-cation doping (1-butyl-3-methylimidazolium tetrafluoroborate or BMIM+BF4 and phenyltrimethylammonium chloride or TMPA+Cl−) were studied by X-ray photoelectron spectroscopy (XPS), contact angle, differential scanning calorimetry (DSC) and impedance spectroscopy (IS) measurements performed with dry samples after 24 h in contact with the IL-cations BMIM+ and TMPA+. IL-cations were selected due to their similar molecular weight and molar volume but different shape, which could facilitate/obstruct the cation incorporation in the Nafion membrane structure by proton/cation exchange mechanism. The surface coverage of the Nafion membrane by the IL-cations was confirmed by XPS analysis and contact angle, while the results obtained by the other two techniques (DSC and IS) seem to indicate differences in thermal and electrical behaviour depending on the doping-cation, being less resistive the Nafion/BMIM+ membrane. For that reason, determination of the ion transport number was obtained for this membrane by measuring the membrane or concentration potential with the samples in contact with HCl solutions at different concentrations. The comparison of these results with those obtained for the original Nafion membrane provides information on the effect of IL-cation BMIM+ on the transport of H+ across wet Nafion/BMIM+ doped membranes.