Search

The present study aimed to use geopolymer materials synthesized from different fly ashes, which are promising for the adsorption of copper ions from aqueous solutions. The characterization of fly ashes and prepared adsorbents was performed by energy-dispersive X-ray spectroscopy (EDS) analysis, Brunauer–Emmett–Teller (BET) surface area analysis, and Scanning Electron Microscopy (SEM). Taguchi and ANOVA methods were used to predict the effect of different working parameters on copper ion removal by prepared geopolymers. Based on data obtained by the Taguchi method, it was found that the factor most influencing the adsorption process is the type of adsorbent used, followed by the solution pH, the reaction time, the adsorbent dose, and the initial copper ion concentration. The ANOVA results agree with the Taguchi method. The optimal conditions of the adsorption process were: fly ash C modified by direct activation with 2 M NaOH, at 70 °C for 4 h, solution pH of 5, initial pollutant concentration of 300 mg/L, 40 g/L adsorbent dose, and 120 min of reaction time. Copper ion removal efficiency was determined experimentally under optimal conditions, achieving a value of 99.71%.

Fiberglass is a waste generated in the construction materials industry, which is not dangerous for the environment, but long-term and very long-term storage is expensive. Finding a method of reuse as in creating a useful composite material led to the research work in this study. The impact of waste fiberglass and furnace slag on the characteristics of novel composite materials was examined in this study. The density and mechanical properties of the composite samples were examined to determine the impact of waste fiberglass (WFG) concentration in it. Washed river aggregates were replaced with WFG in various ratios in our laboratory tests. Concrete class C16/20 was utilized, having 0.35–0.7 w. % WFG and 2–10% slag. The obtained material was evaluated for density, workability, and compressive strength. The experiments were carried out in an accredited concrete station laboratory. The density of the resulting materials decreased as the WFG content was increased. The densities were higher than the witness sample, ranging from 2358 to 2405 kg/m3. The findings show that adding WFG and slag to concrete has a positive impact on its characteristics. With the addition of WFG, the mixture became more non-homogenous, but these characteristics can be optimized in future. Because of the differential in density between WFG and natural coarse aggregates, the fresh density of obtained composites dropped as the percentage of WFG increased; this could be an advantage, as the newly obtained material became lighter. The findings show that adding waste to concrete has a detrimental impact on its qualities. The introduction of blast furnace slag up to 5% does not modify the compressive strength, compared to the reference samples, but 10% slag causes a decrease in compressive strength of 4.2%. A proportion of 0.25% WFG causes a slight increase in mechanical strength; therefore, 0.25% WFG and 5% slag increased the compressive strength, the maximum value being obtained for a composite with 0.25% WFG, 5% slag, 5% sand and aggregates. Capitalization of WFG and slag resulted in significant economic and environmental benefits by reducing waste storage costs and production costs, and advantages resulted from the new material.

The fly ash wastes (materials rich in silica, aluminum, and iron) could be advanced valorized by using as pozzolanic materials in the formulation of mortar and concrete. The partial hydrolysis of its, during alkali activation process, gel formation, and polycondensation produce the compulsory properties. The study had as objective to determine the optimal conditions, and the relationships between the fly ash modifying parameters, particle size and morphology, and behavior in chemical agents of the mortar obtained from different wastes. The alkali activation process involved varying the liquid/solid ratio (quantities of liquid phase) and the concentration of the NaOH solution (8 - 12 M). The samples' morphologies, particle size distribution, Blaine surface values, and crystallography were significant changes as a result of the activation, as demonstrated by XRD and SEM analysis. The durability values were substantially improved comparatively with building materials on the base of cement. As a result, treated fly ash is suitable as a potential building material, saving disposal-related issues. Using treated fly ash is environmentally friendly method conserving a large amount of cement, used in the production of building materials and reducing the CO2 emissions.

Abstract The Congo Red dye was removed from a simulated textile wastewater solution using fly ash from a local power plant. The characterisation of fly ash was studied in detail by SEM, EDX, XRD, FTIR, BET surface area and TGA techniques. The influence of four parameters (contact time, initial concentration, adsorbent dose, and temperature) was analysed, the results showing that the adsorption capacity depends on these parameters. Thermodynamic and regeneration investigations as well are presented. The fit to pseudo-second-order kinetics models suggests that the removal process is a chemical adsorption. The Langmuir model fitted the experimental data, with a maximum adsorption capacity of 22.12 mg/g. The research is a preliminary case study that highlights that fly ash posed a very good potential as a material for Congo Red dye removal.

Glass is a substance that is present in most houses since glass-based items are made and consumed in relatively high quantities. This has led to the buildup of glass in concerning quantities all over the world, which is a problem for the environment. It is well known that glass has several advantageous physiochemical features that qualify it as an appropriate material for use in the construction industry as an aggregate. The features include being non-biodegradable, resistant to chemical assault, having low water absorption, having high hydraulic conductivity, having temperature-dependent ductility, having alterable particle gradation, and having a wide availability in a variety of forms and chemical compositions. Because of these qualities, glass has been used in various investigations and field tests conducted in civil engineering to evaluate its effectiveness as an engineering aggregate and to develop environmentally friendly management strategies for waste glass. These studies and research have utilized glass in various forms, such as fine recycled glass, medium recycled glass, coarse recycled glass, powdered glass, and glass-based geopolymers. This study focuses on research studies that present results on physicochemical, mechanical, and durability characteristics. These studies and research contain samples of pure glass or glass as replacement percentages in materials (0–100%), including but not limited to unbound granular materials (such as recycled concrete aggregates and crushed rock). In light of the information assembled in this review article, it is legitimate to claim that glass has strong promise as a material in various civil applications.

The fly ash generated from a Romanian power plant was used as a starting material in this study. The aim of the study was to obtain a low cost material based on the treatment of fly ash with Fe3O4 for utilization as an adsorbent for cadmium ion removal. The adsorbent that was synthesized was characterized using different techniques. The adsorption process was investigated by the batch technique at room temperature. The quantity of cadmium ion adsorbed was measured spectrophotometrically. The experimental data showed that the material can remove cadmium ions at all three working concentrations. The adsorption capacity increased with an increase in concentration, respectively contact time. The results were analyzed through two kinetic models: pseudo first order and pseudo second order. The kinetics results of cadmium adsorption onto a magnetic material are in good agreement with a pseudo second order model, with a maximum adsorption capacity of 4.03 mg/g, 6.73 mg/g, and 9.65 mg/g. Additionally, the pseudo second order model was linearized into its four types. The results indicated that the material obtained show the ability to remove cadmium ions from an aqueous solution.

This work focused on the use of cellulose acetate polymer for the preparation of porous asymmetric membranes using a phase inversion process. These membranes were characterised by scanning electron microscopy, a bubble-point method and sorption measurements. The preparation method used induced membrane anisotropy. The capacity of the membranes in the removal of electrolyte (NaCl) from aqueous solution was investigated. A good retention of 58.6% and a high flux rate of 8.9 × 10–4 m/s using NaCl solution of 200 mg/L concentration were obtained by cellulose acetate membranes prepared with water as non-solvent. The results showed that the membrane performance was affected by the membrane structure, which was determined by the conditions of membrane preparation.

This study aimed to analyse the bioaccumulation of heavy metal ions in plants of spontaneous flora. An urban area was established from which soil samples were taken and analyses were performed on the content of heavy metal ions. The soil samples were collected from Iasi’s urban area to determine the heavy metal concentrations, obtain maps of sensitive land, and determine the content of heavy metals in spontaneous flora and transfer these into an aqueous extract. The investigation of heavy metal ion levels in certain plants revealed the following: (i) all plants from the Brassicaceae accumulate heavy metals, and B. juncea has a great ability to accumulate and transfer Cu, Cr(VI), Cd, Ni, Pb, and Zn towards the shoots; (ii) heavy metals (Fe, Cu, Cr, Mn, Zn) were present in variable concentrations, with mint and nettle being notable for their increased level of iron and thyme, and rattle for its zinc levels; (iii) toxic metals (Pb, Cd, Ni) are present in low concentrations in plants as well as in infusions, except for in primula and plantain, which do not have high levels of Pb and Cd. The results showed that values exceeded the maximum recommended values in areas with industrial pollution. Taking into account the potential for the bioaccumulation of heavy metal ions by plants from spontaneous flora and their use as medicinal plants, it is recommended, based on the studies conducted, to harvest and use plants from soils that do not contain heavy metal ions.

CeO2/ZnO-based photocatalytic materials were synthesized by the sol-gel method in order to establish heterojunctions that increase the degradation efficiency of some types of antibiotics by preventing the recombination of electron–hole pairs. The synthesized materials were analysed by XRD, SEM, EDAX, FTIR, and UV-Vis. After several tests, the optimal concentration of the catalyst was determined to be 0.05 g‧L−1 and 0.025 g‧L−1 for chlortetracycline and 0.05 g‧L−1 for ceftriaxone. CeO2/ZnO assemblies showed much better degradation efficiency compared to ZnO or CeO2 tested individually. Sample S3 shows good photocatalytic properties for the elimination of ceftriaxone and tetracycline both from single solutions and from the binary solution. This work provides a different perspective to identify other powerful and inexpensive photocatalysts for wastewater treatment.

The effectiveness of a Fe3O4-loaded fly ash composite for the adsorption of Congo red dye was assessed in this work. The structure and properties of the magnetic adsorbent were established by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffractometer (XRD), vibrating sample magnetometer (VSM), and dynamic light scattering (DLS). The magnetic results showed a saturation magnetization value of 6.51 emu/g and superparamagnetic behavior. The main parameters that influence the removal of Congo red dye adsorbent such as dose, initial concentration, and contact time were examined. The Freundlich adsorption isotherm and pseudo-second-order kinetic model provided the best fit for the experimental findings. The Congo red dye’s maximum adsorption capacity of 154 mg/g was reported in the concentration range of 10–100 mg/L, using the proposed magnetic adsorbent. The results of the recyclability investigation demonstrated that the circular economy idea is valid. The adsorbent that was synthesized was also further characterized by XRD and FTIR techniques after Congo red dye adsorption.

Biomass fly ash (BFA) from a biomass cogeneration plant was encapsulated into calcium alginate microspheres (ALG/Ca) and characterized. An FTIR analysis indicated that BFA loading weakened molecular interactions between ALG/Ca constituents (mainly hydrogen bonding and electrostatic interactions), thus changing the crosslinking density. SEM and AFM analyses revealed a wrinkled and rough surface with elongated and distorted granules. The in vitro release of BFA’s main components (K, Ca, and Mg) was controlled by diffusion through the gel-like matrix, but the kinetics and released amounts differed significantly. The smaller released amounts and slower release rates of Ca and Mg compared to K resulted from the differences in the solubility of their minerals as well as from the interactions of divalent cations with alginate chains. The physicochemical properties of the novel microsphere formulation reveal significant potential for the prolonged delivery of nutrients to crops in a safe manner.

TiO2 nanoparticles synthesized by the sol-gel method and doped with Ag were characterized by SEM, EDAX, FTIR, BET, XRD and TEM, then tested in the photocatalytic degradation of methylene blue (MB) under UV irradiation. The experimental results indicate that the average size of the raw particles was 10 nm, and their size was increased by calcination. The photocatalytic degradation of MB on nanostructured TiO2-Ag shows a high degradation efficiency upon the addition of a photosensitizer. A parametric study of the process was performed and has revealed the optimal value of the photocatalyst dose (0.3 g L−1) at a MB concentration of 4 ppm. Afterwards, the effect of acetone as a photosensitizer was studied. A MB degradation mechanism was proposed to explain the synergy between the TiO2 and the silver nanoparticles in the degradation performance. Under the optimal experimental conditions, at photosensitizer doses of 0.1 and 0.2%, yields of 92.38% and 97.25% MB degradation were achieved, respectively. Kinetic models showed that, at 0.1% acetone concentration, the data fit the pseudo-first-order model, while at 0.2% acetone, the photodegradation mechanism fits a second-order model. The values of the apparent rate constants indicate that the reaction rate increased between 24 and 40 times in the presence of acetone on TiO2 and TiO2-Ag. The addition of acetone modified the photodegradation mechanism and the Ag-doped samples became more active. The results of recycling tests using calcined TiO2-Ag material clearly show that the material was highly photocatalytically stable for the MB degradation. According to experimental results, the dye degradation decreased from 97.25% to 92.39% after four consecutive cycles. This simple approach could be applied for the advanced cleaning of wastewater contaminated with dyes, in the perspective of its reuse.

Two types of biosorbents, based on Saccharomyces pastorianus immobilized in calcium alginate, were studied for the removal of pharmaceuticals from aqueous solutions. Synthetized biocomposite materials were characterized chemically and morphologically, both before and after simulated biosorption. Ethacridine lactate (EL) was chosen as a target molecule. The process performance was interpreted as a function of initial solution pH, biosorbent dose, and initial pharmaceutical concentration. The results exhibited that the removal efficiencies were superior to 90% for both biosorbents, at the initial pH value of 4.0 and biosorbent dose of 2 g/L for all EL initial concentrations tested. Freundlich, Temkin, Hill, Redlich-Peterson, Sips, and Toth isotherms were used to describe the experimental results. The kinetic data were analyzed using kinetic models, such as pseudo-first order, pseudo-second order, Elovich, and Avrami, to determine the kinetic parameters and describe the transport mechanisms of EL from aqueous solution onto biosorbents. Among the tested equations, the best fit is ensured by the pseudo-second-order kinetics model for both biosorbents, with the correlation coefficient having values higher than 0.996. The many potential advantages and good biosorptive capacity of Saccharomyces pastorianus biomass immobilized in calcium alginate recommend these types of biocomposite materials for the removal of pharmaceuticals from aqueous solutions.

In this study, ethacridine lactate removal from aqueous solution using a biosorbent material based on residual microbial biomass and natural polymers in fixed-bed continuous column was investigated. Composite beads of Saccharomyces pastorianus residual biomass and calcium alginate were obtained by immobilization technique. The prepared biosorbent was characterized by Fourier transformed infrared spectroscopy, scanning electron microscopy, and analysis of point of zero charge value. Then, laboratory-scale experiments by fixed-bed column biosorption were conducted in continuous system. To this purpose, the column bed high (5 cm; 7.5 cm), initial pollutant concentration (20 mg/L; 40 mg/L), and solution flow through the column (0.6 mL/min; 1.5 mL/min) were considered the main parameters. Recorded breakthrough curves suggest that lower flow rates, greater bed heights, and a lower concentration of ethacridine lactate led to an increased biosorption of the target compound. The biosorption dynamic was investigated by nonlinear regression analysis using the Adams–Bohart, Yoon–Nelson, Clark, and Yan mathematical models. Conclusively, our research highlights, firstly, that the obtained biosorbent material has the required properties for retaining the ethacridine lactate from aqueous solution in continuous system. Secondly, it emphasizes that the modeling approach reveals an acceptable fitting with the experimental data for the Yoon–Nelson, Clark, and Yan models.

Pharmaceuticals are recognized as emerging water microcontaminants that have been reported in several aquatic environments worldwide; therefore, the elimination of these pollutants is a global challenge. This study aimed to develop a biosorbent based on Saccharomyces pastorianus residual biomass encapsulated in a calcium alginate matrix and to evaluate its biosorption performance to remove Ethacridine Lactate (EL) from aqueous solutions. Firstly, the synthesis and characterization of biosorbent has been carried out. Then, the impact of main parameters on biosorption process were investigated by batch experiments. Finally, the kinetics behavior and equilibrium isotherms were evaluated. The resulted beads have an irregular and elongated shape with about 1.89 mm ± 0.13 mm in size with a homogeneous structure. The best removal efficiency for EL of over 85% was obtained at acidic pH 2 and 25 °C for 50 mg/L initial concentration and 2 g/L biosorbent dose. The pseudo-second-order and intraparticle diffusion kinetics describe the biosorption process. The maximum calculated biosorption capacity was 21.39 mg/g similar to that recorded experimentally. The equilibrium biosorption data were a good fit for Freundlich and Dubinin–Radushkevich isotherms. Our findings reveal that the low cost and eco-friendly obtained biosorbent can be easily synthesized and suitable to remove Ethacridine Lactate from water matrices.

Fly ash wastes (silica, aluminum and iron-rich materials) could be smartly valorized by their incorporation in concrete formulation, partly replacing the cement. The necessary binding properties can be accomplished by a simple procedure: an alkali activation process, involving partial hydrolysis, followed by gel formation and polycondensation. The correlations between the experimental fly ash processing conditions, particle characteristics (size and morphology) and the compressive strength values of the concrete prepared using this material were investigated by performing a parametric optimization study to deduce the optimal processing set of conditions. The alkali activation procedure included the variation of the NaOH solutions concentration (8–12 M), temperature values (25–65 °C) and the liquid/solid ratio (1–3). The activation led to important modifications of the crystallography of the samples (shown by powder XRD analysis), their morphologies (seen by SEM), particle size distribution and Blaine surface values. The values of the compressive strength of concrete prepared using fly ash derivatives were between 16.8–22.6 MPa. Thus, the processed fly ash qualifies as a proper potential building material, solving disposal-associated problems, as well as saving significant amounts of cement consumed in concrete formulation.

This study investigated the adsorption capacity of one material based on the treatment of fly ash with sodium hydroxide as a novel adsorbent for toxic Cu2+ ion removal from aqueous media. The adsorbent was obtained through direct activation of fly ash with 2M NaOH at 90 °C and 6 h of contact time. The adsorbent was characterized by recognized techniques for solid samples. The influence of adsorption parameters such as adsorbent dose, copper initial concentration and contact time was analyzed in order to establish the best adsorption conditions. The results revealed that the Langmuir model fitted with the copper adsorption data. The maximum copper adsorption capacity was 53.5 mg/g. The adsorption process followed the pseudo-second-order kinetic model. The results indicated that the mechanism of adsorption was chemisorption. The results also showed the copper ion removal efficiencies of the synthesized adsorbents. The proposed procedure is an innovative and economical method, which can be used for toxicity reduction by capitalizing on abundant solid waste and treatment wastewater.

Cephalexin (CPX) is recognized as a water pollutant, and it has been listed in a number of countries with a risk factor greater than one. Herein, the present work focused on the synthesis, characterization and biosorption capacity evaluation of Saccharomyces cerevisiae immobilized in calcium alginate as a biosorbent to remove CPX from aqueous solutions. Biosorbent was characterized by SEM and FTIR techniques. Batch biosorption experiments were conducted in order to evaluate the effect of the initial pH, biosorbent dose and CPX initial concentration. The removal efficiency, in considered optimal conditions (pH = 4, CPX initial concentration = 30 mg/L, biosorbent dose = 1 g/L) was 86.23%. CPX biosorption was found to follow the pseudo–second-order kinetics. The equilibrium biosorption data were a good fit for the Langmuir model with correlation coefficient of 0.9814 and maximum biosorption capacity was 94.34 mg/g. This study showed that the synthesized biosorbent by immobilization technique is a low-cost one, easy to obtain and handle, eco-friendly, with high feasibility to remove CPX antibiotic from aqueous solution. The findings of this study indicate that the biosorbents based on microorganisms immobilized on natural polymers have the potential to be applied in the treatment of wastewater.

Novel hybrid inorganic CoFe2O4/carboxymethyl cellulose (CMC) polymeric framework nanobeads-type adsorbents with tailored magnetic properties were synthesized by a combination of coprecipitation and flash-cooling technology. Precise self-assembly engineering of their shape and composition combined with deep testing for cadmium removal from wastewater are investigated. The development of a single nanoscale object with controllable composition and spatial arrangement of CoFe2O4 (CF) nanoparticles in carboxymethyl cellulose (CMC) as polymeric matrix, is giving new boosts to treatments of wastewaters containing heavy metals. The magnetic nanobeads were characterized by means of scanning electron microscopy (SEM), powder X-ray diffraction analysis (XRD), thermogravimetric analysis (TG), and vibrational sample magnetometer (VSM). The magnetic properties of CF@CMC sample clearly exhibit ferromagnetic nature. Value of 40.6 emu/g of saturation magnetization would be exploited for magnetic separation from aqueous solution. In the adsorptions experiments the assessment of equilibrium and kinetic parameters were carried out by varying adsorbent dosage, contact time and cadmium ion concentration. The kinetic behavior of adsorption process was best described by pseudo-second-order model and the Langmuir isotherm was fitted best with maximum capacity uptake of 44.05 mg/g.

The initial characteristics of Romanian fly ash from the CET II Holboca power plant show the feasibility of its application for the production of a new material with applicability in environmental decontamination. The material obtained was characterized using standard techniques: scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), instrumental neutron activation analysis (INAA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), the Brunauer–Emmett–Teller (BET) surface area, and thermogravimetric differential thermal analysis (TG-DTA). The adsorption capacity of the obtained material was evaluated in batch systems with different values of the initial Cu(II) ion concentration, pH, adsorbent dose, and contact time in order to optimize the adsorption process. According to the experimental data presented in this study, the adsorbent synthesized has a high adsorption capacity for copper ions (qmax = 27.32–58.48 mg/g). The alkali treatment of fly ash with NaOH improved the adsorption capacity of the obtained material compared to that of the untreated fly ash. Based on the kinetics results, the adsorption of copper ions onto synthesized material indicated the chemisorption mechanism. Notably, fly ash can be considered an important beginning in obtaining new materials with applicability to wastewater treatment.

This work highlights new insights into the performance of TiO2 doped with noble metal catalysts for the photocatalytic degradation of organic water pollutants. Different samples of titanium dioxide doped with noble metals (Au and Pd) were successfully synthesized via incipient wet impregnation (IWI) and ultrasound-assisted impregnation (US) methods. X-ray diffraction, scanning electron microscopy and UV-Vis reflectance spectroscopy were used for the characterization of the obtained materials. Their photocatalytic efficiency was investigated in aqueous suspension thorough a series of laboratory tests performed under ultraviolet (UV-A) irradiation conditions using 2,4 dinitrophenol (2,4 DNP) as a target molecule. The results clearly show that the method used for the catalyst synthesis affects its photocatalytic activity. It was found that the samples prepared by the IWI method exhibited high photocatalytic activity, and the removal rate obtained with TiO2-Pd/IWI was higher than that found for TiO2-Au/IWI. Furthermore, for the best catalyst, some extra photocatalytic experiments were conducted with rhodamine 6G (R6G), a highly stable molecule with a very different chemical structure to 2,4 DNP, in order to check the reactivity of this material. Moreover, the recycling experiments carried out with TiO2-Pd/IWI clearly demonstrated the high photocatalytic stability of this material for the degradation of 2,4 DNP. All of the collected data confirmed the interesting photocatalytic potential of the selected catalyst in the elimination of organic pollutants with no obvious change in its reactivity after four reaction cycles, which is very promising for promoting future applications in water depollution.

Fly ash/magnetite material was used for the adsorption of copper ions from synthetic wastewater. The obtained material was characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET) surface area, and vibrating sample magnetometer (VSM). Batch adsorption experiments were employed in order to investigate the effects of adsorbent dose, initial Cu (II) concentration and contact time over adsorption efficiency. The experimental isotherms were modeled using Langmuir (four types of its linearization), Freundlich, Temkin, and Harkins–Jura isotherm models. The fits of the results are estimated according to the Langmuir isotherm, with a maximum adsorption capacity of 17.39 mg/g. The pseudo-second-order model was able to describe kinetic results. The data obtained throughout the study prove that this novel material represents a potential low-cost adsorbent for copper adsorption with improved adsorption capacity and magnetic separation capability compared with raw fly ash.

In the present paper, aspects concerning the obtained and characterization of additive systems used for maximizing filler retention, and the effects on paper properties, were investigated. The effects of retention additives over properties of paper, containing fibers from in-situ loading (IS-CCP), were analyzed against the effects of additives over properties of paper containing fibers from conventional loading, obtained by the addition of calcium carbonate in precipitated form (CCP). The physico-mechanical properties were analyzed by various analyses and investigations: calcium carbonate content, X-ray diffraction, scanning electron microscopy (SEM) images, optical and mechanical properties, in order to develop the best systems of retention additives for obtaining higher retention loads for making paper with high content of nano-filler material. The obtained results reveal that at the same level of calcium carbonate content, all paper samples with in-situ loading had higher the optical and mechanical properties than the paper obtained by conventional loading in all cases the additives studied. For all studied properties, nanoparticles had a positively influence over paper properties.

Mixed oxides containing zinc and lanthanum were prepared by coprecipitation in alkaline medium, followed by calcination at 400 °C. The initial precipitation product and the calcined form were characterized by Brunauer–Emmett–Teller (BET) method adsorption of nitrogen at −196 °C, Scanning Electron Microscopy/Electron-Probe Microanalysis (SEM/EPM), Ultraviolet—Diffuse Reflectance Spectroscopy (UV-DRS) and Infrared (IR) spectroscopy. The band gap slightly changes from 3.23 eV to 3 eV by calcination. The photocatalytic performance of the solids were investigated in diluted aqueous medium, by using clofibric acid (CA), a stable and toxic molecule used as precursor in some pesticides and drugs, as test compound, possibly found in the wastewaters in low concentrations. The effects of the degradation extent, determined by high performance liquid chromatography (HPLC) and total organic carbon (TOC) measurements, were investigated at different initial concentrations of CA. Within about 60 min the CA degradation is almost total at low concentration values (3 ppm) and reaches over 80% in 180 min for an initial concentration of 50 ppm. Moreover, the CA removal performance of photocatalyst remains excellent after three cycles of use: the removal yield was practically total after 60 min in the first two cycles and reached 95% even in the third cycle.

Wastes are the sustainable sources of raw materials for the synthesis of new adsorbent materials. This study has as objectives the advanced capitalization of fly ash, by sulphuric acid activation methods, and testing of synthesized materials for heavy metals removal. Based on the previous studies, the synthesis parameters were 1/3 s/L ratio, 80 °C temperature and 10% diluted sulphuric acid, which permitted the synthesis of an eco-friendly adsorbent. The prepared adsorbent was characterized through SEM, EDX, FTIR, XRD and BET methods. Adsorption studies were carried out for the removal of Cd2+ ions, recognized as ions dangerous for the environment. The effects of adsorbent dose, contact time and metal ion concentrations were studied. The data were tested in terms of Langmuir and Freundlich isotherm and it was found that the Langmuir isotherm fitted the adsorption with a maximum adsorption capacity of 28.09 mg/g. Kinetic data were evaluated with the pseudo-first-order model, the pseudo-second-order model and the intraparticle diffusion model. The kinetics of cadmium adsorption into eco-friendly material was described with the pseudo-second-order model, which indicated the chemisorption mechanism.

The goal of this study was to analyze the effects of cellulose fibers loading by precipitation in-situ of calcium carbonate over the properties of printing paper obtained from mixtures of the softwood and hardwood fibers. The effects of fibers with in-situ loading were analyzed comparatively with conventional paper loading respectively, by adding precipitated calcium carbonate into fiber stock. The effectiveness of the methods was evaluated by various analyses and investigations: calcium carbonate content, Scanning electron microscope (SEM) images, X-ray diffraction, optical and mechanical properties of the paper sheets. The evaluation of the effects on paper properties led to the conclusion that, at the same filler content, the in-situ loading method gives higher opacity and brightness than conventional methods. The utilization of cellulose fibers with in-situ loading as additive, shown as a modification of the ratio between fibers with in-situ loading and fibers without loading, regardless of whether they are softwood or hardwood fibers, allowed us to optimize printing paper properties, especially regarding the relationship between optical and strength properties.

Polymer concrete is a composite material realized with resin and aggregates. In the present study the epoxy resin was used for binding the aggregates. In the composition were introduced near the fly ash, used as filler, the cellulose fibers. The mechanical characteristics such as compressive strength, flexural strength and split tensile strength of polymer concrete with fibers were investigated. The fiber percentage was constant, the epoxy resin and the filler dosages were varied. The cellulose fiber had not improved the mechanical characteristics of the polymer concrete in comparison to that of polymer concrete without cellulose fibers.

In the paper are presented the results of some experimental researches concerning polymer mortars and concretes realized of epoxy resin, silica fume and crushed aggregates. The mechanical characteristics of hardened concrete were determined. The silica fume content varied between 6.5% and 30% to polymer mortar and 6.4% and 9.6% to polymer concrete. The obtained results show maximum characteristics for a dosage of 24% resin and maximum dosage of silica fume to the polymer mortar, and for the polymer concrete the mechanical characteristics are influenced by all mixture factors: the compressive strength increases with the increase of silica fume dosage, and the flexure strength and split strength increase with the decreasing of silica fume dosage.