Search

The paper is focused on steel surface processing to ensure an improved adhesion of applied powder layer. Mechanical pre-treatment, chemical pre-treatment and their combination were used to compare their results with each other and to find out the pre-treatment that affected the final outcome the most. The final score was determined by the grid method. The outcome displayed a huge mutual dependency between the result and a kind of various surface treatments. The method with no pre-treatment was by far the worst, followed by the mechanical pre-treatment only, followed by the chemical pre-treatment only, and finally by their combination. The time of blasting affects the final outcome. Through the grid method, coating thickness, and aesthetic test it was confirmed that an optimal blasting time of 5 min provides the best outcome.

Biomass is a potential biofuel which may help fighting high carbon dioxide emissions and negative impacts of global warming. Analysis of Norway spruce (Picea abies) and barley (Hordeum vulgare) were performed at the laboratory of Czech University of Life Sciences. Material was torrefied in an inert nitrogen atmosphere at the temperatures of 250 °C and 280 °C for 45 minutes. Elementary and stoichiometric parameters were monitored and impact of torrefaction and pellet production on carbon footprint was determined. Torrefied and pelleted material showed better fuel properties in comparison to the original material. Calorific value of the torrefied spruce wood chip increased by 12.27% when torrefied at the temperature of 250 °C, and by 25.41% when torrefied at the temperature of 280 °C.

Biomass energy for heating is going to be part of the spectrum of renewable energy sources. However, biomass combustion produces emissions of various pollutants with negative effects at both local and global scales. To reduce some of the locally important pollutant load, thermally treated biomass fuels may offer a partial solution. In this study, two biomass feedstocks, i.e., spruce chips and rapeseed straw, were thermally treated at 300 °C to produce biochars. Subsequently, both original materials and biochars were burned in a 25 kW retort combustion device. In both cases, the biochar showed lower emissions of carbon monoxide and nitrogen oxides, usually almost across the whole range of tested combustion conditions. In total, for the emission production per unit of net calorific value, the spruce biochar showed reductions in CO and NOx productions of 10.8% and 14.5%, respectively. More importantly, in rapeseed straw biochar, the difference was more pronounced. The total production was reduced by 28% and 42%, again in CO and NOx emissions, respectively. [ABSTRACT FROM AUTHOR]

The issue of carbon monoxide and nitrogen oxides emissions into the atmosphere is very current. This article thus focuses on the assessment of elemental composition of selected herbal biomass species and emission concentrations during combustion in a commonly available grate combustion device for briquetted fuel. In tests, emission concentrations were evaluated in contrast to the oxygen concentration in flue gas and flue gas temperatures. Samples of camelina (Camelina sativa), giant miscanthus (Miscanthus gigantheus), reed canary grass (Phalaris arundinacea L.) and sorghum (Sorghum bicolor) were used. Elementary and stoichiometric combustion analyses were conducted for these samples (LECO AC-600 semi-automatic calorimeter, CHN628 + S elemental analyser and LECO TGA-701 analyser). Analyses of C, H, N and S concentrations and calorific values showed that samples of briquetted herb biomass had insignificant differences and could be used for energy purposes without limitation. The limiting factor was the high amount of ash, which amounted to 6.59% of dry weight in reed canary grass briquette sample. Furthermore, a high percentage (1.91% wt.) of nitrogen was observed in reed canary grass briquettes. Such a high amount of nitrogen during combustion tests resulted in an increase in NOx emission levels in flue gas of the Phalaris arundinacea L. sample, in which it reached the maximum concentration of 375.20 mg·m−3. The combustion tests showed that even under steady-state conditions, high concentrations of carbon monoxide could not be avoided for tested briquetted biofuels without active regulation of the combustion process.

Maize grown on sloped areas is susceptible to surface runoff and soil erosion, especially if traditional technology with tillage is employed. As a result, other solutions are being sought that address this risk and are acceptable to farmers. The combination of inter-row cultivation with the formation of small reservoirs appears to be a suitable alternative solution applicable in traditional corn cultivation. In the years 2020, 2021, and 2022, three plots of land in southern Bohemia, Czech Republic, were selected for testing, on which this approach was tested. During the field experiments, three variants were compared each year: inter-row cultivation with reservoirs, inter-row cultivation only, and a control without any mechanical intervention. All variants were subjected to rain simulation, from which the surface runoff was evaluated. The highest retention of runoff was manifested with reservoir cultivation by 2.4–4.2 min, compared to the cultivated variant, and 2–4.2 min compared to the control. This result would correspond to a difference of 5.7–9.8 mm retained precipitation and 4.6 to 7.3 mm, respectively. The hydraulic conductivity of the soil was evaluated after canopy closure. The lowest values were invariably reached in the reservoirs, up to 88% lower than with the cultivated variant and 79% lower than the control. The fresh matter yield of forage maize was shown to be inconclusively higher by up to 10% in 2020 and 2022 in cultivation with reservoirs. However, the dry matter yield was always lower in the variant with reservoirs compared to inter-row cultivation only. Overall, reservoir cultivation appears to be an effective method for the retention of rainwater on agricultural land with a slope up to 6° without a significant effect on the yield of maize. [ABSTRACT FROM AUTHOR]

The issue of carbon monoxide and nitrogen oxides emissions into the atmosphere is very current. This article thus focuses on the assessment of elemental composition of selected herbal biomass species and emission concentrations during combustion in a commonly available grate combustion device for briquetted fuel. In tests, emission concentrations were evaluated in contrast to the oxygen concentration in flue gas and flue gas temperatures. Samples of camelina (Camelina sativa), giant miscanthus (Miscanthus gigantheus), reed canary grass (Phalaris arundinacea L.) and sorghum (Sorghum bicolor) were used. Elementary and stoichiometric combustion analyses were conducted for these samples (LECO AC-600 semi-automatic calorimeter, CHN628 + S elemental analyser and LECO TGA-701 analyser). Analyses of C, H, N and S concentrations and calorific values showed that samples of briquetted herb biomass had insignificant differences and could be used for energy purposes without limitation. The limiting factor was the high amount of ash, which amounted to 6.59% of dry weight in reed canary grass briquette sample. Furthermore, a high percentage (1.91% wt.) of nitrogen was observed in reed canary grass briquettes. Such a high amount of nitrogen during combustion tests resulted in an increase in NOx emission levels in flue gas of the Phalaris arundinacea L. sample, in which it reached the maximum concentration of 375.20 mg·m−3. The combustion tests showed that even under steady-state conditions, high concentrations of carbon monoxide could not be avoided for tested briquetted biofuels without active regulation of the combustion process. [ABSTRACT FROM AUTHOR]