Search

A comparative study of Pt(II)- and Pt(IV)-porphyrins as novel ionophores for anion-selective polymeric membrane electrodes is performed. Polymeric membranes of different compositions, prepared by varying plasticizers, cationic and anionic additives and Pt porphyrins, have been examined by potentiometric and optical techniques. Pt porphyrin-based devices were found to exhibit enhanced potentiometric selectivity toward iodide ion compared to electrodes based on a typical anion-exchanger (e.g. tridodecylmethylammonium chloride). It is shown that Pt(II)-porphyrins function as neutral anion carriers within the electrode membranes, while those based on Pt(IV)TPPCl(2) operate via a mixed mode carrier mechanism, evidencing also a partial reduction of the starting ionophore to Pt(II)TPP. Spectrophotometric measurements of thin polymeric films indicate that no spontaneous formation of hydroxide ion bridged porphyrin dimers occurs in the membrane plasticized both with high or low dielectric constant plasticizer, due to a low oxophilicity of central Pt. The computational study of various anion-Pt(IV)TPPCl(2) complex formation by means of semi-empirical and density functional theory (DFT) methods revealed a good correlation between calculated and measured ionophore selectivity.

Polymer membrane electrodes operated by pulsed chronopotentiometry have recently been introduced to replace traditional ion-selective electrodes for a number of applications. While ion-selective electrodes for the polycation protamine have been reported, for instance, a pulsed chronopotentiometric readout mode (called here pulstrode) provides improved stability and reproducibility while exhibiting sufficient selectivity for the direct detection of protamine in undiluted whole blood samples. Here, such protamine-sensitive pulstrodes are applied for the real-time detection of the activity of the protease trypsin and its soybean inhibitor. This is possible because small fragments produced by the trypsin digestion are not detectable by the protamine-sensing membrane. The real-time response to the proteolytic reaction is shown to exhibit good reproducibility and reversibility, and the initial reaction rate is dependent on the concentration of the protease and its inhibitor.

Ion-selective electrodes ideally operate on the basis of the Nernst equation, which predicts less than 60- and 30-mV potential change for a 10-fold activity change of monovalent and divalent ions measured at room temperature, respectively. Typical concentration ranges in extracellular fluids are quite narrow for the electrolytes of key importance. A range of 2.2-2.6 mM for calcium ions, for instance, translates into just a 2.2-mV potential change. The direct potentiometric measurement of physiological electrolytes is certainly possible with direct potentiometry and is done routinely in clinical analyzers and handheld measuring devices. It places, however, strong demands on the precision of the reference electrode and requires careful temperature control and frequent calibration runs. In this paper, a robust 10-20-fold sensitivity enhancement for calcium measurements is attained by departing from the classical response mechanism and operating in a non-Nernstian response mode. Stable and reproducible super-Nernstian responses of these so-called pulstrodes in a narrow calcium activity range can be controlled by instrumental means in good agreement with theory. The potentials may be measured during a galvanostatic excitation pulse (mode I) or immediately after it (mode II), under open-circuit conditions. Subtraction of the potentials, sampled at different times during a single pulse, allows one to obtain a sensitive differential peak-shaped signal at a critical and fully adjustable analyte activity range. Calcium pulstrodes based on the diamide ionophore AU-1 were characterized and applied to the measurement in model physiological liquids. Super-Nernstian responses exceeding 700 mV/decade were observed in a physiological range of calcium concentration. Such remarkable sensitivity of the pulstrodes, complemented with the well-documented high selectivity of these potentiometric sensors, may provide a significant increase in the accuracy and precision of electrolyte measurements in clinical analysis.

Ion-selective electrode membranes based on hydrophobic materials doped with chemically selective host molecules are an attractive sensing technology but normally suffer from a limited sensitivity, given by the Nernst equation, and a direct reliance on the reference electrode potential, which makes miniaturization difficult. These fundamental problems are addressed here by imposing a multipulse electrochemical excitation signal onto ion-selective membranes that lack ion-exchange properties. Current pulses are responsible for the generation of ion fluxes in the direction of the membrane, which give reproducible super-Nernstian response slopes that originate from depletion processes at the membrane surface. Membranes may also be measured at zero current after this pulse, giving super-Nernstian response regions at lower concentrations. Difference potentials obtained from subsequent pulses give about 10-fold higher sensitivities than predicted on the basis of the Nernst equation.

Novel carbonate ionophore, trifluoroacetophenone derivative (TFA) substituted by two acceptor substituents in the phenyl ring (3-bromo-4-hexyl-5-nitrotrifluoroacetophenone), was synthesized. Solvent polymeric membrane sensors based on this ionophore exhibited heightened selectivity to carbonate ions in the presence of the most important interfering anions. A wide range of potentiometric properties were studied and compared with those of sensors based on mono-substituted ionophores. Special attention was paid to pH dependence of sensor responses and to elaboration of appropriate conditions for carbonate analysis. A segmented-sandwich membrane method was applied for determination of the stoichiometry of ionophore-carbonate complexes, which was determined to be 1:3, and apparent complex formation constants which were 14.4 and 13.6 for DOS- and NPOE-plasticized membranes, respectively. Theoretical studies on TFA derivatives by semi-empirical (AM1 and PM3) and ab initio(6-31+G*) methods were performed, considering different types of possible ionophore-ion interactions. The formation of hydrogen bonds between carbonate and hydrated TFA was proved to be much more favourable in terms of energy compared to tetrahedral nucleophilic adducts that earlier were postulated to being formed in the membrane phase. The final conclusion on the mechanism of carbonate sensing by TFA-based solvent polymeric membrane sensors was made on the basis of computational data and detailed analysis of the literature.

The electronic tongue based on an array of 30 non-specific potentiometric chemical sensors has been applied to qualitative and quantitative monitoring of a batch fermentation process of starting culture for light cheese production. Process control charts were built by using PLS regression and data from fermentations run under "normal" operating conditions. Control charts allow discrimination of samples from fermentation batches run under "abnormal" operating conditions from "normal" ones at as early as 30-50% of fully evolved fermentations. The capability of the electronic tongue to quantify concentrations of important organic acids (citric, lactic and orotic) in the present type of fermentation media was demonstrated. Average prediction errors were assessed in the range 5-13% based on test set validation. Correlation between peptide profiles determined using HPLC and the electronic tongue output was also established. The electronic tongue was demonstrated to be a promising tool for fermentation process monitoring and quantitative analysis of growth media.

A flow-injection multisensor system (FIMS) comprising potentiometric sensors of different types for determination of free cyanide activity in basic solutions for extraction of noble metals was developed. The solvent polymeric membrane sensors based on metalloporphyrin and crystalline sensors were combined in the sensor system. The system allowed determination of cyanide activity in the range 10(-4)-1 mol l(-1) with an error less than 5% in individual cyanide solutions and acceptable precision (about 20%) in process liquids. The system was able to analyse up to 20 samples per h. The FIMS was also applied to detecting of silver ions in the presence of cyanide. Chalcogenide glass sensor was used as the detector that ensured the precision of 20%.