Search

Lopinavir (LPV) and ritonavir (RTV) are two of the essential antiretroviral active pharmaceutical ingredients (APIs) characterized by poor solubility. Hence, attempts have been made to improve both their solubility and dissolution rate. One of the most effective approaches used for this purpose is to prepare amorphous solid dispersions (ASDs). To our best knowledge, this is the first attempt aimed at developing ASDs via the electrospinning technique in the form of fibers containing LPV and RTV. In particular, the impact of the various polymeric carriers, i.e., Kollidon K30 (PVP), Kollidon VA64 (KVA), and Eudragit® E100 (E100), as well as the drug content as a result of the LPV and RTV amorphization were investigated. The characterization of the electrospun fibers included microscopic, DSC, and XRD analyses, the assessment of their wettability, and equilibrium solubility and dissolution studies. The application of the electrospinning process led to the full amorphization of both the APIs, regardless of the drug content and the type of polymer matrix used. The utilization of E100 as a polymeric carrier for LPV and KVA for RTV, despite the beads-on-string morphology, had a favorable impact on the equilibrium solubility and dissolution rate. The results showed that the electrospinning method can be successfully used to manufacture ASDs with poorly soluble APIs. [ABSTRACT FROM AUTHOR]

Lead-free K0.5Bi0.5TiO3 (KBT) ceramics with high density (~5.36 g/cm3, 90% of X-ray density) and compositional purity (up to 90%) were synthesized using a solid-state reaction method. Strongly condensed KBT ceramics revealed homogenous local microstructures. TG/DSC (Thermogravimetry-differential scanning calorimetry) techniques characterized the thermal and structural stability of KBT. High mass stability (>0.4%) has proven no KBT thermal decomposition or other phase precipitation up to 1000 °C except for the co-existing K2Ti6O13 impurity. A strong influence of crystallites size and sintering conditions on improved dielectric and non-linear optical properties was reported. A significant increase (more than twice) in dielectric permittivity (εR), substantial for potential applications, was found in the KBT-24h specimen with extensive milling time. Moreover, it was observed that the second harmonic generation (λSHG = 532 nm) was activated at remarkably low fundamental beam intensity. Finally, spectroscopic experiments (Fourier transform Raman and far-infrared spectroscopy (FT-IR)) were supported by DFT (Density functional theory) calculations with a 2 × 2 × 2 supercell (P42mc symmetry and C4v point group). Moreover, the energy band gap was calculated (Eg = 2.46 eV), and a strong hybridization of the O-2p and Ti-3d orbitals at Eg explained the nature of band-gap transition (Γ → Γ). [ABSTRACT FROM AUTHOR]

The development of new chemically resistant anodes for protonic ceramic fuel cells (PCFCs) is urgently required to avoid the costly deep hydrogen purification method. Ba0.95Ca0.05Ce0.9Y0.1O3−δ (5CBCY), which is more chemically resistant than BaCaCe0.9Y0.1O3−δ, was here tested as a component of a composite NiO–5CBCY anode material. A preparation slurry comprising 5CBCY, NiO, graphite, and an organic medium was tape cast, sintered and subjected to thermal treatment in 10 vol.% H2 in Ar at 700 °C. Differential thermal analysis, thermogravimetry, quadrupole mass spectrometry, X-ray diffraction analysis, scanning electron microscopy, the AC four-probe method and electrochemical impedance spectroscopy were used for the investigation. The electrical conductivity of the Ni–5CBCY in H2–Ar at 700 °C was 1.1 S/cm. In the same gas atmosphere but with an additional 5 vol.% CO2, it was slightly lower, at 0.8 S/cm. The Ni–5CBCY cermet exhibited repeatable electrical conductivity values during Ni-to-NiO oxidation cycles and NiO-to-Ni reduction in the 5CBCY matrix, making it sufficient for preliminary testing in PCFCs. [ABSTRACT FROM AUTHOR]