Search

Background: Diagnosis of loosening of total wrist implants is usually late using routine radiographs. Switching modality to computed tomography (CT) should aid in early diagnosis. Purpose: To propose and evaluate the accuracy of a new CT method for assessing loosening of the carpal component in total wrist arthroplasty. Material and Methods: A protocol encompassing volume registration of paired CT scans of patients with unexplained pain in a prosthetically replaced wrist (used in clinical routine) is presented. Scans are acquired as a dynamic examination under torsional load. Using volume registration, the carpal component of the prosthesis is brought into spatial alignment. After registration, prosthetic loosening is diagnosed by a shift in position of the bones relative to the prosthesis. This study is a preclinical validation of this method using a human cadaverous arm with a cemented total wrist implant and tantalum markers. Seven CT scans of the arm were acquired. The scans were combined into 21 pairs of CT volumes. The carpal component was registered in each scan pair, and the residual mismatch of the surrounding tantalum markers and bone was analyzed both visually and numerically. Results: The detection limit for prosthetic movement was less than 1 mm. Conclusion: The results of this study demonstrate that CT volume registration holds promise to improve detection of movement of the carpal component at an earlier stage than is obtainable with plain radiography. [ABSTRACT FROM AUTHOR]

Accurately estimating polyethylene wear in 3 dimensions, without the need for additional procedures or equipment, is of significant interest. We investigated the use of a high-resolution clinical computed tomographic (CT) scanner to estimate femoral head displacement relative to the cup as an indirect method of estimating polyethylene wear. A hip phantom was used to simulate the 3-dimensional displacement of a femoral head. The phantom was imaged in a high-resolution CT scanner. The mean difference between the true phantom displacement as positioned by micrometers and the calculated displacement based on the CT images was as follows: for the x-axis, 0 mm (SD, 0.213; SE, 0.058); y-axis, 0.039 mm (SD, 0.035; SE, 0.026); and z-axis, 0.039 mm (SD, 0.051; SE, 0.020)., (Copyright © 2012 Elsevier Inc. All rights reserved.)

Introduction: Examination with CT and image registration is a new technique that we have previously used to assess 3D segmental motions in the lumbar spine in a phantom. Current multi-slice computed tomography (CT) offers highly accurate spatial volume resolution without significant distortion and modern CT scanners makes it possible to reduce the radiation dose to the patients. Our aim was to assess segmental movement in the lumbar spine with the aforementioned method in healthy subjects and also to determine rotation accuracy on phantom vertebrae., Material and Method: The subjects were examined in flexion-extension using low dose CT. Eleven healthy, asymptomatic subjects participated in the current study. The subjects were placed on a custom made jig which could provoke the lumbar spine into flexion or extension. CT examination in flexion and extension was performed. The image analysis was performed using a 3D volume fusion tool, registering one of the vertebrae, and then measuring Euler angles and distances in the registered volumes., Results: The mean 3D facet joint translation at L4-L5 was in the right facet joint 6.1 mm (3.1-8.3), left facet joint 6.9 mm (4.9-9.9), at L5-S1: right facet joint 4.5 mm (1.4-6.9), and for the left facet joint 4.8 mm (2.0-7.7). In subjects the mean angles at the L4-L5 level were: in the sagittal plane 14.3°, coronal plane 0.9° (-0.6 to 2.8), and in the transverse plane 0.6° (-0.4 to 1.5), in the L5-S1 level the rotation was in sagittal plane 10.2° (2.4-16.1), coronal plane 0° (-1.2 to 1.2), and in the transverse plane 0.2° (-0.7 to 0.3). Repeated analysis for 3D facet joint movement was on average 5 mm with a standard error of mean of 0.6 mm and repeatability of 1.8 mm (CI 95%). For segmental rotation in the sagittal plane the mean rotation was 11.5° and standard error of mean 1°. The repeatability for rotation was 2.8° (CI 95%). The accuracy for rotation in the phantom was in the sagittal plane 0.7°, coronal plane 1°, and 0.7 in the transverse plane., Conclusion: This method to assess movement in the lumbar spine is a truly 3D method with a high precision giving both visual and numerical output. We believe that this method for measuring spine movement is useful both in research and in clinical settings.

Kinematic analysis for in vivo assessment of elbow endoprostheses requires knowledge of the exact positions of motion axes relative to bony landmarks or the prosthesis. A prosthesis-based reference system is required for comparison between individuals and studies. The primary aim of this study was to further develop an earlier described algorithm for fusion of radiostereometric analysis (RSA) data and data obtained in 3D computed tomography (CT) for application to the elbow after total joint replacement. The secondary aim was to propose a method for marking of prostheses in 3D CT, enabling definition of a prosthesis-based reference system. Six patients with elbow endoprostheses were investigated. The fusion of data made it possible to visualize the motion axes in relation to the prostheses in the 3D CT volume. The differences between two repeated positioning repetitions of the longitudinal prosthesis axis were less than 0.6 degrees in the frontal and sagittal planes. Corresponding values for the transverse axis were less than 0.6 degrees in the frontal and less than 1.4 degrees (in four out of six less than 0.6 degrees ) in the horizontal plane. This study shows that by fusion of CT and RSA data it is possible to determine the accurate position of the flexion axes of the elbow joint after total joint replacement in vivo. The proposed method for implant marking and registration of reference axes enables comparison of prosthesis function between patients and studies., (2010 Elsevier Ltd. All rights reserved.)

Objective: In this study we explore the possibility of accurately and cost-effectively monitoring tibial deformation induced by Taylor Spatial Frames (TSFs), using time-separated computed tomography (CT) scans and a volume fusion technique to determine tibial rotation and translation., Materials and Methods: Serial CT examinations (designated CT-A and CT-B, separated by a time interval of several months) of two patients were investigated using a previously described and validated volume fusion technique, in which user-defined landmarks drive the 3D registration of the two CT volumes. Both patients had undergone dual osteotomies to correct for tibial length and rotational deformity. For each registration, 10 or more landmarks were selected, and the quality of the fused volume was assessed both quantitatively and via 2D and 3D visualization tools. First, the proximal frame segment and tibia in CT-A and CT-B were brought into alignment (registered) by selecting landmarks on the frame and/or tibia. In the resulting "fused" volume, the proximal frame segment and tibia from CT-A and CT-B were aligned, while the distal frame segment and tibia from CT-A and CT-B were likely not aligned as a result of tibial deformation or frame adjustment having occurred between the CT scans. Using the proximal fused volume, the distal frame segment and tibia were then registered by selecting landmarks on the frame and/or tibia. The difference between the centroids of the final distal landmarks was used to evaluate the lengthening of the tibia, and the Euler angles from the registration were used to evaluate the rotation., Results: Both the frame and bone could be effectively registered (based on visual interpretation). Movement between the proximal frame and proximal bone could be visualized in both cases. The spatial effect on the tibia could be both visually assessed and measured: 34 mm, 10 degrees in one case; 5 mm, 1 degrees in the other., Conclusion: This retrospective analysis of spatial correction of the tibia using Taylor Spatial Frames shows that CT offers an interesting potential means of quantitatively monitoring the patient's treatment. Compared with traditional techniques, modern CT scans in conjunction with image processing provide a high-resolution, spatially correct, and three-dimensional measurement system which can be used to quickly and easily assess the patient's treatment at low cost to the patient and hospital.

Improvement of joint prostheses is dependent upon information concerning the biomechanical properties of the joint. Radiostereometric analysis (RSA) and electromagnetic techniques have been applied in previous cadaver and in vivo studies on the elbow joint to provide valuable information concerning joint motion axes. However, such information is limited to mathematically calculated positions of the axes according to an orthogonal coordinate system and is difficult to relate to individual skeletal anatomy. The aim of this study was to evaluate the in vivo application of a new fusion method to provide three-dimensional (3D) visualization of flexion axes according to bony landmarks. In vivo RSA data of the elbow joint's flexion axes was combined with data obtained by 3D computed tomography (CT). Results were obtained from five healthy subjects after one was excluded due to an instable RSA marker. The median error between imported and transformed RSA marker coordinates and those obtained in the CT volume was 0.22 mm. Median maximal rotation error after transformation of the rigid RSA body to the CT volume was 0.003 degrees . Points of interception with a plane calculated in the RSA orthogonal coordinate system were imported into the CT volume, facilitating the 3D visualization of the flexion axes. This study demonstrates a successful fusion of RSA and CT data, without significant loss of RSA accuracy. The method could be used for relating individual motion axes to a 3D representation of relevant joint anatomy, thus providing important information for clinical applications such as the development of joint prostheses.

We describe and validate a volumetric three-dimensional registration method, and compare it to our previously validated two-dimensional/three-dimensional method. CT/MRI and SPECT data from 14 patients were interactively fused using a polynomial warping technique. Registration accuracy was confirmed visually and by a nonsignificant F value from multivariate analysis of the transformed landmarks, a significant difference of the squared sum of intensity differences between the transformed/untransformed and the reference volume both at the 0.05 (p > 0.05) confidence level and an average 31% improvement of the correlation coefficient and cross correlation. For the two-dimensional/three-dimensional method, ROI center-to-center distance ranged from 1.42 to 11.32 mm (for liver) with an average of 6.13 mm +/- 3.09 mm. The average ROI overlap was 92.51% with a 95% confidence interval of 90.20-96.88%. The new method is superior because it operates on the true three-dimensional volume. Both methods give good registration results, take 10 to 30 min, and require anatomic knowledge.

We present a graphical three-dimensional method that facilitates image registration and fusion, and provides quantitative geometric and volume information. In particular it enhances the use of functional (radiopharmaceutical) imaging (SPECT, PET) which, though a powerful clinical tool, has the disadvantage of low spatial resolution and ill-defined boundaries. Registration between functional images and structural images (MRI, CT) can augment the anatomical context of these functional images.

This paper describes a cost-effective technique that optimally utilizes all available diagnostic studies for three-dimensional treatment planning. A simulator unit modified to produce cross-sectional images (simulator-CT unit) is used to create a reference data set with the patient in the treatment position. Registration software (qsh) brings other diagnostic studies into agreement with this reference data set. Two cases are presented as examples of the use of this technique. Registration of abdominal scans from the same patient demonstrates the warping of a nontreatment position study to the treatment position. The second case is based on paired data sets through the head, in which the diagnostic study was obtained by using a gantry tilt to follow the base of the skull and to avoid sections passing through the teeth. The registration software provides a method for combining diagnostic studies into a single "master" data set. The success of the transformation depends on the operator's ability to identify corresponding anatomic landmarks for different data sets and on the magnitude of the variation in the patient's position from one procedure to the next. Limitations in image quality and the number of cross-sections obtainable from a simulator-CT unit can be partially overcome by using the described technique. Thus, the information contained in nontreatment position diagnostic tests can be used accurately for treatment planning at limited cost.

An integrated approach to existing methods of extracting biodistribution data, pharmacokinetics and radiation absorbed dose estimates from serial scintigraphic images is described. This approach employs a single computer-generated user interface to reformat planar scans into a standard file type, align conjugate (anterior and posterior) images, draw regions of interest (ROIs) over selected organs and lesions and generate count data for anterior and posterior views and calculated geometric means. Using standard correction methods, the fraction injected activity is obtained for all ROIs and total body. This methodology has been applied to the analysis of indium-III-labelled breast-cancer-directed antibodies and technetium-90m-labelled CEA-specific antibody fragments in non-small-cell lung cancer. It is anticipated that this approach will be useful for evaluating the dosimetry of other radiolabelled monoclonal antibodies, as well as other radiopharmaceuticals.

There is great interest at present in incorporating image-management systems popularly referred to as picture archiving and communication systems (PACS) into imaging departments. This paper will describe various aspects of local area networks (LANs) for medical images and will give a definition of terms and classification of devices by describing a possible system which links various digital image sources through a high-speed data link and a common image format, allows for viewing and processing of all images produced within the complex, and eliminates the transport of films. The status of standards governing LAN and particularly PACS systems along with a proposed image exchange format will be given. Prototype systems, particularly a system for nuclear medicine images, will be presented, as well as the prospects for the immediate future in terms of installations started and commercial products available. A survey of the many questions that arise in the development of a PACS for medical images and also a survey of the presently suggested/adopted answers will be given.

Computer-controlled graphic displays are a necessity in many nuclear medicine studies. The authors propose using a set-up consisting of three modules: (a) a display system based on television technology; (b) an instrument interface employing list mode and having a low information loss rate; and (c) flexible modular software which can easily be tailored to the needs of both radiologists and technicians. The authors consider a mini-computer system with broad, flexible applications to be a valuable tool, particularly for those function studies which can only be done by means of nuclear medicine techniques.

In many nuclear Medicine studies computer-controlled graphic displays are an absolute necessity for obtaining meaningful results. Design criteria developed by an interdisciplinary scientific panel are presented to achieve a display system based on television technology; an instrument interface employing list mode using bubble-memory storage technology, thus having a low information-loss rate; and flexible modular software easily tailored to the specific needs of both clinicians and technicians. The panel considers a minicomputer system with broad, flexible applications to be a valuable tool, particularly in doing those function studies that only can be done via nuclear medicine techniques. The final specifications ultimately allow the selection of a vendor and hospital installation, even though all criteria are not currently achievable.

Two major difficulties associated with medical image processing are the diverse image formats that must be dealt with because of the differences in image sources and the number of incompatible display systems available for viewing images both before and after processing. We describe a very small set of primitives that need to be defined to utilize any raster display. When these primitives have been implemented for a particular device, then a standard set of image display programs can be compiled and images and the results of image processing can be displayed. The main purpose of this paper is to describe what a raster display looks like from the point of view of the programmer and to define the specific hardware and software data about the raster display that must be known in order to implement the small set of primitives.

We describe a software system developed to handle images obtained from different sources, namely, computer-assisted tomography, positron emission tomography, single photon emission tomography and magnetic resonance imaging. In developing the system, it was necessary to address the following points. (1) The types of values that were encountered in both the header information and the pixel elements, namely, integers, floating point numbers, complex numbers and strings. (2) The use of domain-dependent sets of keys, that is, how to choose keys and how to stabilize the use of keys among the user population. This is, for example, how information such as the patient name, or the activity in becquerel is kept. It is necessary to keep both the key values and the units. (3) The development of a method for providing a database using flat files, i.e. linear text. (4) The maintenance of a history of values and operations. This is necessary in order to address the problem of determining from an image how that image was produced. The connection between an image and how it was derived is analogous to describing how a secondary standard is derived from a primary one.