Search

A large amount of fruit waste is being a great environmental and social problem due to a lack of adequate storage. Among the most abundant waste is papaya, due to its high consumption in various varieties. These wastes can generate bioelectricity through organic waste, being an important parameter the pH. In this research, low-cost laboratory-scale microbial fuel cells were fabricated, using papaya waste as fuel at different pH (4, 5.73, 7, and 9) to obtain the optimum operating pH. It was possible to observe the maximum values ​​of electric current and voltage of 17.97 mA and 1.02 V on days 16 and 14, in the cell with pH 7; while the cell with pH was the one that showed the lowest values. The electrical conductivity values ​​increased from the first day, observing a maximum peak of 172.50 mS/cm for the cell with pH 7. However, the internal resistance values ​​were low, the maximum value being for the cell with pH 4 (234.61 ± 34 Ω) and the minimum for the cell with pH 7 (46.543 ± 3.6 Ω). In the same way, the maximum power density was for the cell with pH 7 of approximately 645.74 ± 33.64 mW/cm2 and a current density of 5.42 A/cm2.

Potential use of organic waste and microalgae generates bioelectricity and thereby reduces harmful effects on the environment. These residues are used due to their high content of electron-generating microorganisms. However, so far, they have not been used simultaneously. Therefore, this research uses mango waste and microalgae Spirulina sp. in double-chamber microbial fuel cells to generate bioelectricity. The cells were made at a laboratory scale using zinc and copper electrodes, achieving a maximum current and voltage of 7.5948 ± 0.3109 mA and 0.84546 ± 0.314 V, with maximum electrical conductivity of the substrate being 157.712 ± 4.56 mS/cm and an optimum operating pH being 5.016 ± 0.086. The cells showed a low internal resistance of approximately 205.056 ± 25 Ω, and a maximum power density of 657.958 ± 21.114 mW/cm2 at a current density of 4.484 A/cm2. This research provides an excellent opportunity for mango farmers and exporting and importing companies because they can use their own waste to reduce their electricity costs when this prototype is brought to a large scale.

Power generation and wastewater treatment are two great challenges for sustainable development. Microbial fuel cells (MFCs) are a sustainable alternative that can generate bioelectricity in the bioremediation process of wastewater. For this reason, the objective of this research was to generate bioelectricity through double-chamber microbial-combustion cell systems from wastewater from the Covicorti Wastewater Treatment Plant (PTARC) in the anodic chamber and electrogenic bacteria such as Stenotrophomonas maltophilia, Acinetobacter bereziniae, and Achromobacteria xylosoxidans in the cathode chamber, respectively. Measurements of the voltage, current, power density, current density, and optical density of the bacteria and biochemical oxygen demand (BOD) were made. In addition, a metagenomic analysis of the wastewater sample was performed. It was shown that the MFC with A. xylosoxidans generated the highest voltage peak (1.01 ± 0.06 V) on day 24, while the MFC with S. maltophilia generated the highest current value (0.71 ± 0.02 mA). The pH levels were slightly alkaline, and the maximum anodic conductivity value was presented by the MFC with A. cerevisiae, with a peak value of 81 ± 2 mS/cm on day 24. On the other hand, a maximum power density and current density of 195,493 ± 4717 mW/m2 and 4987 A/cm2, respectively, were obtained in the MFC with A. xylosoxidans. Finally, the metagenomic analysis identified the predominant phyla of Proteobacteria present in wastewater samples capable of generating electrical energy as Bacillota, Pseudomonadota, Bacteroidota, Actinomyketone, and Campylobacterota.

This research used tomato waste as a substrate (fuel) in Single Chamber-Microbial Fuel Cells (scMFC) on a small scale. The electrochemical properties were monitored, the functional groups of the substrate were analyzed by Fourier Transform Infrared Spectrophotometry (FTIR) and a microbiological analysis was performed on the electrodes in order to identify the microorganisms responsible for the electrochemical process. The results show voltage peaks and an electrical current of 3.647 ± 0.157 mA and 0.957 ± 0.246 V. A pH of 5.32 ± 0.26 was measured in the substrate with an electrical current conductivity of 148,701 ± 5849 mS/cm and an internal resistance (Rint) of 77. 517 ± 8.541 Ω. The maximum power density (PD) displayed was 264.72 ± 3.54 mW/cm2 at a current density (CD) of 4.388 A/cm2. On the other hand, the FTIR spectrum showed a more intense decrease in its peaks, with the compound belonging to the phenolic groups being the most affected at 3361 cm−1. The micrographs show the formation of a porous biofilm where molecular identification allowed the identification of two bacteria (Proteus vulgaris and Proteus vulgaris) and a yeast (Yarrowia lipolytica) with 100% identity. The data found show the potential of this waste as a source of fuel for the generation of an electric current in a sustainable and environmentally friendly way, generating in the near future a mechanism for the reuse of waste in a beneficial way for farmers, communities and agro-industrial companies.

Antibiotics are often prescribed to treat infections caused by group B Streptococcus; however, inappropriate use of antibiotics can develop resistance. Because of this, the research was carried out with the aim of evaluating the in vitro effect of the hydroalcoholic extract of Caesalpinia spinosa (Molina) Kuntze known as Taya or Tara on the viability of β-hemolytic streptococci; an experimental investigation of increasing stimulation was carried out. The hydroalcoholic extract of C. spinosa pods was worked in concentrations of 250, 500, 750, and 1000 mg/mL, which were placed on filter paper discs to perform the sensitivity test following the Kirby–Bauer method. The greatest inhibition of bacterial viability was observed in the penicillin control group (GPT-01) followed by the TCT-04 group (hydroalcoholic Tara extract 1000 mg/mL). In addition, it was found that these groups are statistically different from the rest (p < 0.05), while the lowest bacterial inhibition was obtained for the erythromycin group and the TCT-01 group (250–1000 mg/mL). It was concluded that the hydroalcoholic extract of the pods of C. spinosa (Molina) Kuntze affects the viability of β-hemolytic streptococci associated with strep pharyngitis and that this antimicrobial activity is due to the presence of tannins, steroidal flavonoid, and alkaloids. Likewise, the tested concentrations of hydroalcoholic Tara extract were found to have better antibacterial activity than erythromycin (15 µg/mL) against β-hemolytic streptococci. These results are hopeful for the traditional or herbal medicine field. However, future in vivo research is needed to determine its effectiveness in humans.

In this study, we aimed to determine the in vitro activity of Leuconostoc mesenteroides var. mesenteroides isolated from sugar-industry effluents to produce a dextran bioflocculant from sucrose as a low-cost substrate. L. mesenteroides strains present in residual cane juice from a sugar factory were isolated and biochemically identified using Mayeux, Sandine, and Elliker agar (MSE) as a selective medium. The strain number 3 (LM03) was biochemically identified as L. mesenteroides var. mesenteroides, which was used for this study. The concentration of dextran was quantified by dry weight, the morphology and purity were evaluated using Fourier-transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). Flocculation was evaluated via turbidimetric assays in different pH ranges from sugar-industry effluents and doses of dextran. To evaluate the flocculant activity according to the effect of pH, a jar test kit from Phipps and Bird, USA, was used with the sample recollected from the effluent (sugar industry). The pH of the samples was adjusted to 7, 8, 9, 10 and 11, with a dose of 40 ppm (dextran dose) at a fast and slow speed of 150 and 50 rpm, respectively. To evaluate the influence of the dose of dextran, values of 5, 20 and 40 ppm were used with fast speeds of 180–150 rpm and slow speeds of 30–50 rpm, respectively. The strain (LM03) was able to produce the highest concentration of dextran (26.87 g/L) in 76 h of incubation. The presence of dextran was identified in the MSE agar after incubation and characterized by FTIR, SEM, and EDS. Besides that, we observed that the best flocculation activity was observed at a pH of 9 and a concentration of 40 ppm of dextran, with a fast agitation speed of 150 rpm for 5 min and a slow agitation speed of 50 rpm for 15 min, achieving 77.7% removal of turbidity from the sugar factory effluent. L. mesenteroides was responsible for the bioflocculation of dextran in different sugar-industry effluents.

The effluents generated in the paper industry, such as black liquor, have a high content of lignin and other toxic components; however, they represent a source of lignin-degrading bacteria with biotechnological potential. Therefore, the present study aimed to isolate and identify lignin-degrading bacteria species in paper mill sludge. A primary isolation was carried out from samples of sludge present in environments around a paper company located in the province of Ascope (Peru). Bacteria selection was made by the degradation of Lignin Kraft as the only carbon source in a solid medium. Finally, the laccase activity (Um-L−1) of each selected bacteria was determined by oxidation of 2,2′-azinobis-(3-etilbencenotiazolina-6-sulfonate) (ABTS). Bacterial species with laccase activity were identified by molecular biology techniques. Seven species of bacteria with laccase activity and the ability to degrade lignin were identified. The bacteria Agrobacterium tumefasciens (2), Klebsiella grimontii (1), and Beijeinckia fluminensis (1) were reported for first time. K. grimowntii and B. fluminensis presented the highest laccase activity, with values of 0.319 ± 0.005 UmL−1 and 0.329 ± 0.004 UmL−1, respectively. In conclusion, paper mill sludge may represent a source of lignin-degrading bacteria with laccase activity, and they could have potential biotechnological applications.

The increase in the population and its need to produce food has caused the level of contamination by organic waste to increase exponentially in recent years. Innovative methods have been proposed for the use of this waste and thus to mitigate its impact. One of these is to use it as fuel in microbial fuel cells to generate electricity. This research aims to generate bioelectricity using coriander waste in microbial fuel cells. The maximum voltage and current observed were 0.882 ± 0.154 V and 2.287 ± 0.072 mA on the seventh and tenth day, respectively, these values were obtained working at an optimum operating pH of 3.9 ± 0.16 and with an electrical conductivity of 160.42 ± 4.54 mS/cm. The internal resistance observed in the cells was 75.581 ± 5.892 Ω, with a power density of 304.325 ± 16.51 mW/cm2 at 5.06 A/cm2 current density. While the intensity of the final FTIR (Fourier transform infrared spectroscopy) spectrum peaks decreased compared to the initial one, likewise, with a percentage of identity, it was possible to attribute 98.97, 99.39, and 100% to the species Alcaligenes faecalis, Alcaligenes faecali, and Pseudomonas aeruginosa. Finally, the cells were connected in series, managing to turn on an LED light (red) with the 2.61 V generated. This research provides an innovative and environmentally friendly way that companies and farmers can use to reuse their waste.

The large amount of molasses that are generated in sugar-processing companies are not always redistributed for commercialization in by-products. Because of this, the present research uses these wastes as fuel in low-cost, lab-scale, single-chamber microbial fuel cells. Zinc and copper electrodes were used as electrodes and 100 mL of molasse in the chamber as fuel, managing to generate current and voltage peaks of 1.73 ± 0.13 mA and 0.953 ± 0.142 V. In monitoring the conductivity of the substrate, a maximum peak of 111.156 ± 8.45 mS/cm was observed, and a slightly acidic pH was observed throughout the monitoring. It was possible to obtain a power density of 5.45 ± 0.31 W/cm2 for a current density of 308.06 mA/cm2, while the yeast count showed a logarithmic curve throughout the monitoring. Finally, the molecular technique identified 100% of the special C. boidinii present in the anodic electrode. This research will give great benefits to sugar companies because they will be able to generate electricity using the molasses that cannot generate by-products.

The environmental problems caused by the excessive use of fossil fuels for electricity generation have led to the development of new technologies. Microbial fuel cells constitute a technology that uses organic sources for electricity generation. This research gives a novel means of using Golden Berry waste as fuel for electricity generation through microbial fuel cells made at low cost, achieving current and voltage peaks of 4.945 ± 0.150 mA and 1.03 ± 0.02 V, respectively. Conductivity values increased up to 148 ± 1 mS/cm and pH increased up to 8.04 ± 0.12 on the last day. The internal resistance of cells was 194.04 ± 0.0471 Ω, while power density was 62.5 ± 2 mW/cm2 at a current density of 0.049 A/cm2. Transmittance peaks of the Fourier-transform infrared (FTIR) spectrum showed a decrease when comparing the initial and final spectra, while the bacterium Stenotrophomonas maltophilia was molecularly identified with an identity percentage of 99.93%. The three cells connected in series managed to generate 2.90 V, enough to turn on a TV remote control. This research has great potential to be scalable if it is possible to increase the electrical parameters, generating great benefits for companies, farmers, and the population involved in the production and marketing of this fruit.

The effluents generated by the tannery industry have a high content of chromium and other toxic elements, representing a potential threat to ecosystems. An eco-friendly alternative to treat these effluents is the use of microorganisms, such as fungi, with the capacity to biosorb heavy metals. The present work aims to determine the effect of the molasses concentration, pH variation, and time on the removal of total chromium using the filamentous fungus Trichoderma spp. An experimental design was adopted using pH (4 and 6), concentrations of molasses (0.5 and 1%), and time (8 and 12 days) as independent variables. The Trichoderma inoculum was constant in all the treatments. The different treatments were evaluated after 0, 8, and 12 days by taking 50 mL of sample from each bioreactor. The chromium concentration was subsequently determined in each sample. The results show that treatment 3 (1% molasses and pH 4) showed higher chromium removal after both 8 and 12 days. The concentrations of total chromium decreased from 665 mg/mL to values of 568 mg/mL by day 8 and 486 mg/mL by day 12. These values are, however, still above the maximum threshold imposed by Peruvian law regarding the discharge of non-domestic effluents into the sewage system. The results show that Trichoderma spp. can increasingly remove chromium from the effluent with longer incubation periods. However, future studies are necessary to determine the mechanisms of chromium biosorption by the fungus and the influence of other physicochemical parameters.

This research aimed to use kiwi waste as fuel to generate bioelectricity through microbial fuel cells. It was possible to generate an electrical current and voltage peaks of 3.807 ± 0.102 mA and 0.993 ± 0.061 V on day 11, showing an electrical conductivity of 189.82 ± 3.029 mS/cm and an optimum operating pH of 5.966 ± 0.121. The internal resistance of the cells was calculated using Ohm’s Law, resulting in a value of 14.957 ± 0.394 Ω, while the maximum power density was 212.68 ± 26.84 mW/m2 at a current density of 4.506 A/cm2. Through the analysis of the FTIR spectra carried out on the substrate, a decrease in the characteristic organic peaks was observed due to their decomposition during the electricity-generation process. In addition, it was possible to molecularly identify the bacteria Comamonas testosteroni, Sphingobacterium sp., and Stenotropho-monas maltophila adhered to the anodized biofilm. Finally, the capacity of this residue to generate bioelectricity was demonstrated by lighting an LED bulb with a voltage of 2.85 V.

Pollution generated by the misuse of large amounts of fruit and vegetable waste has become a major environmental and social problem for developing countries due to the absence of specialized collection centers for this type of waste. This research aims to generate electricity in an eco-friendly way using red dragon fruit (pitahaya) waste as the fuel in single-chamber microbial fuel cells on a laboratory scale using zinc and copper electrodes. It was possible to generate voltage and current peaks of 0.46 ± 0.03 V and 2.86 ± 0.07 mA, respectively, with an optimum operating pH of 4.22 ± 0.09 and an electrical conductivity of 175.86 ± 4.72 mS/cm at 8 °Brix until the tenth day of monitoring. An internal resistance of 75.58 ± 5.89 Ω was also calculated with a maximum power density of 304.33 ± 16.51 mW/cm2 at a current density of 5.06 A/cm2, while the FTIR spectra showed a decrease in the initial compounds and endings, especially at the 3331 cm−1 peaks of the O–H bonds. Finally, the yeast-like fungus Geotrichum candidum was molecularly identified (99.59%). This research will provide great opportunities for the generation of renewable energy using biomass as fuel through electronic devices with great potential to generate electricity.

The compatibility between biocontrol agents and pesticides seems to be a sustainable control strategy in agriculture. Therefore, the in vitro compatibility of three native isolates of Trichoderma was evaluated in three concentrations of chlorpyrifos (960, 1200, and 1440 mg/L), by determining the effect on spore germination, mycelial growth, and the antagonistic capacity. The isolates correspond to Trichoderma asperellum TCA 3, Trichoderma asperellum TCA 21 and Trichoderma harzianum TCA 23. Both spore germination and mycelial growth were performed using the poisoned medium method, while the antagonistic capacity was evaluated against Botrytis sp. in a dual culture. The results showed that TCA 21 strain had a higher germination percentage (79.46, 59.79, and 37.43%) than the TCA 3 and TCA 23 strains, in the three concentrations of chlorpyrifos. Regarding the mycelial growth of the three native strains in chlorpyrifos are affected when concentration of chlorpyrifos increase (p < 0.05). Finally, the antagonistic capacity of the three strains was not affected by any concentration of chlorpyrifos, where strains TCA 21 and TCA 23 presented a degree of antagonism of one, while TCA 3 presented a degree of two, according to the scale used by Bell. In conclusion, T. asperellum TCA 21 was the one that presented the best in vitro compatibility with chlorpyrifos at concentrations of 960 and 1200 mg/L, compared to T. asperellum TCA 3 and TCA 23. These results are favorable for field application since these native strains can also have the ability to degrade the insecticide, representing a sustainable and eco-friendly alternative to the environment.

The objective was to determine the effect of inoculum concentration on the degradation of Diesel 2 by a microbial consortium called BIOT.PD001. For this, five systems were designed (in triplicate), which Contained Davis Minimum Medium, 5% Diesel 2 as a carbon source, and a suspension of the microbial consortium BIOT.PD001 (9 × 108 cells/mL) in concentrations of 2, 4, 6, 8, and 10% of the final volume. The monitoring of the degradation of Diesel 2 was carried out indirectly through the bacterial counts by the plate count method, the Biochemical Oxygen Demand (BOD5) by the Winkler Method modified according to Alsterberg, and the concentration of total fats by Gerber’s method. The retention time was 15 days. It was observed that the percentage of efficiency of the process increases as the concentration of inoculum increases, obtaining the highest percentage of efficiency (94.77%) when using 10% of inoculum (v/v), while when using inoculum concentrations of 2 and 4% (v/v), the efficiency percentages are the lowest, (68.4 and 66.6%, respectively). On the other hand, the variance analysis indicated that there is a significant difference between the averages of these values. The regression analysis indicated that the inoculum concentration significantly affects the efficiency of Diesel 2 degradation and that this is 86% explained by a linear regression model. There is a linear relationship between the inoculum concentration of the BIOT.PD001 microbial consortium and the BOD5 tend to decrease as a function of time. It is concluded that the inoculum concentration significantly affects the efficiency of the degradation of Diesel 2 by the BIOT.PD001 consortium.

The enormous environmental problems that arise from organic waste have increased due to the significant population increase worldwide. Microbial fuel cells provide a novel solution for the use of waste as fuel for electricity generation. In this investigation, onion waste was used, and managed to generate maximum peaks of 4.459 ± 0.0608 mA and 0.991 ± 0.02 V of current and voltage, respectively. The conductivity values increased rapidly to 179,987 ± 2859 mS/cm, while the optimal pH in which the most significant current was generated was 6968 ± 0.286, and the ° Brix values decreased rapidly due to the degradation of organic matter. The microbial fuel cells showed a low internal resistance (154,389 ± 5228 Ω), with a power density of 595.69 ± 15.05 mW/cm2 at a current density of 6.02 A/cm2; these values are higher than those reported by other authors in the literature. The diffractogram spectra of the onion debris from FTIR show a decrease in the most intense peaks, compared to the initial ones with the final ones. It was possible to identify the species Pseudomona eruginosa, Acinetobacter bereziniae, Stenotrophomonas maltophilia, and Yarrowia lipolytica adhered to the anode electrode at the end of the monitoring using the molecular technique.

Papaya (Carica papaya) waste cause significant commercial and environmental damage, mainly due to the economic losses and foul odours they emit when decomposing. Therefore, this work provides an innovative way to generate electricity for the benefit of society and companies dedicated to the import and export of this fruit. Microbial fuel cells are a technology that allows electricity generation. These cells were produced with low-cost materials using zinc and copper electrodes, while a 150 mL polymethylmethacrylate tube was used as a substrate collection chamber (papaya waste). Maximum values of 0.736 ± 0.204 V and 5.57 ± 0.45 mA were generated, while pH values increased from 3.848 to 8.227 ± 0.35 and Brix decreased slowly from the first day. The maximum power density value was 878.38 mW/cm2 at a current density of 7.245 A/cm2 at a maximum voltage of 1072.77 mV. The bacteria were identified with an identity percentage of 99.32% for Achromobacter xylosoxidans species, 99.93% for Acinetobacter bereziniae, and 100.00% for Stenotrophomonas maltophilia. This research gives a new way for the use of papaya waste for bioelectricity generation.

Research on the use of microbial biosensors for monitoring wastewater contaminants is a topic that covers few publications compared to their applicability in other fields, such as biomedical research. For this reason, a systematic analysis of the topic was carried out, for which research-type articles were reviewed during the period 2012 to September 2022. For this, different search platforms were used, including PubMed, ScienceDirect, Springer Link, and Scopus, and through the use of search equations a relevant bibliography was located. After that, the research articles were selected based on exclusion criteria. As a result, it was found that, of the 126 articles, only 16 articles were strictly related to the topic, since there was a duplication of articles among the different databases. It was possible to demonstrate the usefulness of microorganisms as components of biosensors to monitor BOD, heavy metals, and inorganic contaminants in wastewater that also had a high sensitivity. Additionally, recombinant DNA techniques were shown to improve the performance of this type of biosensor and can finally be coupled to other emerging technologies, such as microbial fuel cells (MFCs). In conclusion, it was established that microbial biosensors have high acceptability and monitoring characteristics that make them a useful tool to detect low concentrations of pollutants in wastewater that can also provide results in real-time, thus generating forms of ecological safety and social responsibility in companies where wastewater is generated.

The biosorption of arsenic (As) with macroalgae has aroused much interest as a clean and low-cost technology. To evaluate arsenic biosorption by Chondracanthus chamissoi and Cladophora sp., approximately 5 kg of algae was collected from Huanchaco’s beach and Sausacocha lake (Huamachuco), La Libertad. As biosorption was carried out in four column systems, with 2 g of algae pellets each, circulating As solutions of 0.25 and 1.25 ppm, respectively, at 300 mL/min cm2. As concentration was determined at 3 and 6 h of treatment by flame atomic absorption spectrophotometry. Data were analyzed using Student’s t-test with 95% confidence. At 6 h, Chondracanthus chamissoi presented an As biosorption of 95.76% in a 0.25 ppm mg/L solution and 85.33% in a 1.25 mg/L solution. Cladophora sp., at 6 h, presented an As biosorption of 95.76% in a 0.25 mg/L solution and 42.03% in a 1.25 mg/L solution. It was concluded that Chondracanthus chamissoi achieves higher percentages of biosorption than Cladophora sp. in solutions of 1.25 mg/L As (p < 0.05), and that there is no significant difference between the biosorption percentages of Chondracanthus chamissoi and Cladophora sp. in a 0.25 mg/L solution of As at 6 h of treatment (p > 0.05).

Global warming and the increase in organic waste from agro-industries create a major problem for the environment. In this sense, microbial fuel cells (MFC) have great potential for the generation of bioelectricity by using organic waste as fuel. This research produced low-cost MFC by using zinc and copper electrodes and taking blueberry waste as fuel. A peak current and voltage of 1.130 ± 0.018 mA and 1.127 ± 0.096 V, respectively, were generated. The pH levels were acid, with peak conductivity values of 233. 94 ± 0.345 mS/cm and the degrees Brix were descending from the first day. The maximum power density was 3.155 ± 0.24 W/cm2 at 374.4 mA/cm2 current density, and Cándida boidinii was identified by means of molecular biology and bioinformatics techniques. This research gives a new way to generate electricity with this type of waste, generating added value for the companies in this area and helping to reduce global warming.

The accelerated increase in energy consumption by human activity has generated an increase in the search for new energies that do not pollute the environment, due to this, microbial fuel cells are shown as a promising technology. The objective of this research was to observe the influence on the generation of bioelectricity of sucrose, with different percentages (0%, 5%, 10% and 20%), in papaya waste using microbial fuel cells (MFCs). It was possible to generate voltage and current peaks of 0.955 V and 5.079 mA for the cell with 20% sucrose, which operated at an optimal pH of 4.98 on day fifteen. In the same way, the internal resistance values of all the cells were influenced by the increase in sucrose, showing that the cell without sucrose was 0.1952 ± 0.00214 KΩ and with 20% it was 0.044306 ± 0.0014 KΩ. The maximum power density was 583.09 mW/cm2 at a current density of 407.13 A/cm2 and with a peak voltage of 910.94 mV, while phenolic compounds are the ones with the greatest presence in the FTIR (Fourier transform infrared spectroscopy) absorbance spectrum. We were able to molecularly identify the species Achromobacter xylosoxidans (99.32%), Acinetobacter bereziniae (99.93%) and Stenotrophomonas maltophilia (100%) present in the anode electrode of the MFCs. This research gives a novel use for sucrose to increase the energy values in a microbial fuel cell, improving the existing ones and generating a novel way of generating electricity that is friendly to the environment.

The large amounts of organic waste thrown into the garbage without any productivity, and the increase in the demand for electrical energy worldwide, has led to the search for new eco-friendly ways of generating electricity. Because of this, microbial fuel cells have begun to be used as a technology to generate bioelectricity. The main objective of this research was to generate bioelectricity through banana waste using a low-cost laboratory-scale method, achieving the generation of maximum currents and voltages of 3.71667 ± 0.05304 mA and 1.01 ± 0.017 V, with an optimal pH of 4.023 ± 0.064 and a maximum electrical conductivity of the substrate of 182.333 ± 3.51 µS/cm. The FTIR spectra of the initial and final substrate show a decrease in the peaks belonging to phenolic compounds, alkanes, and alkenes, mainly. The maximum power density was 5736.112 ± 12.62 mW/cm2 at a current density of 6.501 A/cm2 with a peak voltage of 1006.95 mV. The molecular analysis of the biofilm formed on the anode electrode identified the species Pseudomonas aeruginosa (100%), and Paenalcaligenes suwonensis (99.09%), Klebsiella oxytoca (99.39%) and Raoultella terrigena (99.8%), as the main electricity generators for this type of substrate. This research gives a second use to the fruit with benefits for farmers and companies dedicated to exporting and importing because they can reduce their expenses by using their own waste.