Search

Iron-based superconductors have great potential for high-power applications due to their prominent high-field properties. One of the central issues in enhancing the critical current density of iron-based superconducting wires is to reveal the roles and limitations of grain boundaries in supercurrent transport. Here, we finely tuned the electronic properties of grain boundaries by doping Ba1-xKxFe2As2 superconductors in a wide range (0.25

Superconducting joints are one of the key technologies to make Ba1-xKxFe2As2 (Ba-122) superconducting wires or tapes for high-field applications. Herein, superconducting joints were fabricated by a simple cold-pressing method, and the joint resistance of the iron-based superconducting joint was estimated for the first time. The superconducting properties, microstructures, and elements distribution in the joint regions were investigated. At 4.2 K and 10 T, a transport critical current Ic of 105 A for the joint was obtained, and the critical current ratio (CCR= Ic-joint/Ic-tape) of the joint was 94.6%. On the other hand, the joint show very low joint resistance of 2.7x10^-13 ohm in self-field at 4.2 K. Among iron-based superconductors (IBS), this work is the first to successfully realize a superconducting joint with such high CCR and low joint resistance. This work shows great potential to apply Ba-122 in a range of practical applications, where superconducting joints are essential., Comment: 20 pages, 8 figures

Superconducting materials hold great potential to bring radical changes for electric power and high-field magnet technology , enabling high-efficiency electric power generation, high-capacity lossless electric power transmission, small light-weighted electrical equipment, high-speed maglev transportation, ultra-strong magnetic field generation for high-resolution magnetic resonance imaging (MRI) systems, nuclear magnetic resonance (NMR) systems, the future advanced high energy particle accelerators, nuclear fusion reactors and so on. The performance, economy and operating parameters (temperatures and magnetic fields) of these applications strongly depend on the electromagnetic and mechanical properties, as well as manufacturing and material cost of superconductors. This perspective examines the basic properties relevant to practical applications and key issues of wire fabrication for practical superconducting materials, and describes their challenges and current state in practical applications. Finally, future perspectives for their opportunities and development in the applications of superconducting power and magnetic technologies are given., Comment: 40 pages, 8 figures

Nowadays the development of high-field magnets strongly relies on the performance of superconducting materials. Iron-based superconductors exhibit high upper critical fields and low electromagnetic anisotropy, making them particularly attractive for high-field applications, especially in particle accelerator magnets, nuclear magnetic resonance spectrometers, medical magnetic resonance imaging systems and nuclear fusion reactors. Herein, through an industrially scalable and cost-effective manufacturing strategy, a practical level critical current density up to 1.1x10^5 A/cm2 at 4.2 K in an external magnetic field of 10 T was achieved in Cu/Ag composite sheathed Ba0.6K0.4Fe2As2 superconducting tapes. The preparation strategy combines flat rolling to induce grain texture and a subsequent hot-isostatic-pressing densification. By varying the parameters of rolling, the degree of grain texture was engineered. It is found that the transport properties of the Ba1-xKxFe2As2 tapes can be enhanced by applying a large amount of deformation during rolling, which can be attributed to the improved degree of c-axis texture. Microstructure characterizations on the highest-performance tape demonstrate that the Ba1-xKxFe2As2 phase has a uniform element distribution and small grains with good connectivity. Grain boundary pinning is consequently enhanced as proved by large currents circulating through the sample even at 25 K. Our work proves that Cu/Ag composite sheathed Ba1-xKxFe2As2 superconducting tapes can be a promising competitor for practical high-field applications in terms of the viable, scalable and cost-effective fabrication strategy applied and the high transport properties achieved in this work., Comment: 30 pages, 7 figures, accepted to SCIENCE CHINA Materials

We report the temperature, magnetic field and time dependences of magnetization in advanced Ba122 superconducting tapes. The sample exhibits a peculiar vortex creep behavior. Below 10 K, the normalized magnetization relaxation rate S=dln(-M)/dln(t) shows a temperature insensitive plateau with a value comparable to that of the low temperature superconductors, which can be explained within the framework of the collective creep theory. It then enters into a second collective creep regime when the temperature increases. Interestingly, the relaxation rate below 20 K tends to saturate with the increasing field. However, it changes to a power law dependence on field at a higher temperature. A vortex phase diagram composed of the collective and the plastic creep regions is concluded. Benefit from the strong grain boundary pinning, the advanced Ba122 superconducting tape has promising potential to be applied not only in liquid helium but also in liquid hydrogen or at the temperature accessible with cryocoolers., Comment: 5 pages, 4 figures

The iron-based superconductor (IBS) single pancake coil (SPC) with 30 mm inner diameter was firstly fabricated and tested under 24 T background field. This SPC was successfully made using the 7-filamentary Ba1-xKxFe2As2 (Ba122) tape by wind-and-react method. This IBS coil show the highest Ic value at magnetic field reported so far. For example, the transport critical current of this Ba122 SPC achieved 35 A at 4.2 K and 10 T, which is about half of that of short sample. This indicates that the non-insulation winding process together with the stainless-steel tape is suitable to the iron-based superconductor. Even more encouraging is the fact that the Ic of this SPC is still as high as 26 A under 24 T background field, which is still about 40% of that at zero external magnetic field. These results clearly demonstrate that the iron-based superconductors are very promising for high-field magnet applications., Comment: 16 pages, 3 figures

Ag-sheathed CaKFe4As4 superconducting tapes have been fabricated via the ex-situ powder-in-tube method. Thermal and X-ray diffraction analyses suggest that the CaKFe4As4 phase is unstable at high temperatures. It decomposes into the CaAgAs phase which reacts strongly with the silver sheath. We therefore sintered the tape at 500C and obtain a transport critical current density Jc(4.2 K, 0 T)~ 2.7x10^4 A/cm2. The pinning potential derived from magnetoresistance measurements is one order of magnitude lower than that of the (Ba/Sr)1-xKxFe2As2 tapes. Combining with the scanning electron microscopy and magneto-optical imaging results, we suggest that bad connectivity between superconducting grains caused by the low sintering temperature is the main factor responsible for the low Jc. However, this system is still a promising candidate for superconducting wires and tapes if we further optimize the post-annealing process to achieve better grain connectivity., Comment: 17 pages, 6 figures

Superconducting joints are essential for iron-based superconductor's applications in future. In this study, a process for fabricating superconducting joints between Sr1-xKxFe2As2 (Sr-122) tapes is developed for the first time. The Ag sheath was peeled off from one side of each sample. The exposed superconducting parts of the two tapes were joined and wrapped again with Ag foil. The diffusion bonding of the iron-based superconducting joint was achieved by hot-pressing process in Argon atmosphere. The superconducting properties, microstructures and the elements distribution of the joint regions had been investigated. The pressure and pressing times were optimized in order to enhance the transport current of the joints. At 4.2 K and 10 T, a transport critical current Ic of 57 A for the joint was obtained, which is approximately 63.3% of the current capacity of the tapes themselves. Furthermore, the joint resistances dV/dI were estimated from the V-I curve of the joints and the calculated joint resistances values are below 10^-9 Ohm. These results demonstrate that the hot pressing was useful for fabricating the superconducting joint samples., Comment: 26 pages, 9 figures, main results were published in SuST

Superconducting nanowire single-photon detectors (SNSPDs) have an absolute advantage over other types of single photon detectors except the low operating temperature. Therefore, many efforts have been devoted to find high-temperature superconducting materials that are suitable for preparing SNSPDs. Copper-based and MgB2 ultra-thin superconducting nanowires have been already reported. However, the transport properties of iron-based ultra-thin superconducting nanowires have not been studied. In this work, a 10 nm thick 200 nm wide 30 {\mu}m long high quality superconducting nanowire was fabricated from ultrathin BaFe1.84Co0.16As2 films by a lift-off process. The precursor BaFe1.84Co0.16As2 film with a thickness of 10 nm and root-mean-square roughness of 1 nm was grown on CaF2 substrates by pulsed laser deposition. The nanowire shows a high superconducting critical temperature Tzero c=20 K with a narrow transition width of Delta T=2.5 K and exhibits a high critical current density Jc of 1.8E7 A/cm2 at 10 K. These results of ultrathin BaFe1.84Co0.16As2 nanowire will attract interest in electronic applications, including SNSPDs, Comment: 18 pages, 6figures

Iron with a large magnetic moment was widely believed to be harmful to the emergence of superconductivity because of the competition between the static ordering of electron spins and the dynamic formation of electron pairs (Cooper pairs). Thus, the discovery of a high critical temperature (Tc) iron-based superconductor (IBSC) in 2008 was accepted with surprise in the condensed matter community and rekindled extensive study globally. IBSCs have since grown to become a new class of high-Tc superconductors next to the high-Tc cuprates discovered in 1986. The rapid research progress in the science and technology of IBSCs over the past decade has resulted in the accumulation of a vast amount of knowledge on IBSC materials, mechanisms, properties, and applications with the publication of more than several tens of thousands of papers. This article reviews recent progress in the technical applications (bulk magnets, thin films, and wires) of IBSCs in addition to their fundamental material characteristics. Highlights of their applications include high-field bulk magnets workable at 15-25 K, thin films with high critical current density (Jc) > 1 MA/cm2 at ~10 T and 4 K, and an average Jc of 1.3*104 A/cm2 at 10 T and 4 K achieved for a 100-m-class-length wire. These achievements are based on the intrinsically advantageous properties of IBSCs such as the higher crystallographic symmetry of the superconducting phase, higher critical magnetic field, and larger critical grain boundary angle to maintain high Jc. These properties also make IBSCs promising for applications using high magnetic fields., Comment: Published online in Materials Today. Open Access

We comparatively studied the critical current density, magnetization and specific heat of the rolled and the hot-pressed Sr1-xKxFe2As2 tapes. The Schottky anomaly that is obvious in the specific heat of the rolled tape disappears in the hot-pressed tape. Moreover, the hot-pressed tape has a higher fraction of superconductivity and a narrower distribution of superconducting transition temperature than the rolled tape. Combined with the magnetization data, we conclude that sintering under high pressure provides a better environment for complete chemical reaction and more homogenous dopant distribution, which is beneficial to the global current of a superconductor., Comment: 13 pages, 4 figures

The high upper critical field and low anisotropy of iron-based superconductors make them being particularly attractive for high-field applications. However, the current carrying capability needs to be enhanced by overcoming the weak-link effect between misaligned grains inside wire and tape conductors. Here we demonstrate a high transport critical current density (Jc) reaching 1.5x10^5 A/cm^2 (Ic = 437 A) at 4.2 K and 10 T in Ba0.6K0.4Fe2As2 (Ba-122) tapes prepared by a combination of conventional powder-in-tube method and optimized hot-press technique. The transport Jc measured at 4.2 K under high magnetic fields of 27 T is still on the level of 5.5x10^4 A/cm^2, which is much higher than those of low-temperature superconductors. This is the first report of hot-pressed Ba-122 superconducting tapes and these Jc values are by far the highest ever reported for iron-based superconducting wires and tapes. These high-performance tapes exhibit high degree of c-axis texture of Ba-122 grains and low anisotropy of transport Jc, showing great potential for construction of high-field superconducting magnets., Comment: 23 pages, 6 figures