Search

1. Abstract Worldwide, lithium rich ceramic pebbles are being developed to be used as tritium breeders inside future fusion reactors. Upon irradiation, the pebbles will produce tritium which will be used alongside deuterium to fuel the fusion reaction. It is essential that these pebbles are of sufficient quality to withstand the various forces experienced within the wall of the reactor. Currently, a melt-based process is used at the Karlsruhe Institute of Technology for the production of pebbles composed of lithium orthosilicate with a secondary strengthening phase of lithium metatitanate. Recent studies have focused on incorporating lithium orthogermanate, which forms a solid solution with lithium orthosilicate. Various compositions were used to perform fundamental studies to determine phase transitions as well as melting points for processing. The melt-based KALOS process was then used to produce pebbles with selected compositions. Thereafter the pebbles underwent a series of characterisation tests including microstructure and surface analysis using REM as well as elemental mappings using EDX. XRD was used for determining the crystal structures present in various compositions and the unit cell volumes. The measurements showed that the unit cell volume of each structure linearly depends on the composition. Additionally, pebbles were held at reactor relevant temperatures to determine any changes to the mechanical strength. It was found that pebbles with 30 mol% lithium metatitanate and a lithium orthosilicate/orthogermanate ratio in the range of 1.5–4 showed an increased strength as well as good thermal stability and may have the potential to be used as tritium breeders.

The paper reviews the current status of development and qualification of the HCPB TBM’s functional materials, namely, Li-ceramic breeder and Be multiplier materials. The main functional and performance requirements for both functional materials are overviewed. The main results and outcomes of the post-irradiation examinations (PIE) of Li-ceramic breeder and Be/beryllides materials irradiated in HIDOBE and HICU irradiation campaigns are presented aiming at determination of the materials’ performance, properties and characteristics under neutron irradiation, like e.g. morphology and microstructure, tritium retention/release characteristics, mechanical properties. Fabrication of the advanced ceramic breeder material, containing lithium orthosilicate with addition of lithium metatitanate phase in order to improve its mechanical properties, is described. Results of characterization of this advanced ceramic breeder in terms of mechanical properties, porosity, morphology and effective thermal conductivity of a pebble bed are overviewed. In addition, results of characterization of the reference 1 mm Be pebbles produced by Rotation Electrode Process are presented in terms of their microstructure, tritium release characteristics and interaction with air and steam. A necessity to realize in the future a new irradiation experiment for the functional materials, LIBERTI experiment, is discussed in the conclusions.

The tritium loading of current grades of advanced ceramic breeder pebbles with three different lithium orthosilicate (LOS)/lithium metatitanate (LMT) compositions (20–30 mol% LMT in LOS) and pebbles of EU reference material, was performed in a consistent way. The temperature dependent release of the introduced tritium was subsequently investigated by temperature programmed desorption (TPD) experiments to gain insight into the desorption characteristics. The obtained TPD data was decomposed into individual release mechanisms according to well-established desorption kinetics. The analysis showed that the pebble composition of the tested samples does not severely change the release behaviour. Yet, an increased content of lithium metatitanate leads to additional desorption peaks at medium temperatures. The majority of tritium is released by high temperature release mechanisms of chemisorbed tritium, while the release of physisorbed tritium is marginal in comparison. The results allow valuable projections for the tritium release behaviour in a fusion blanket.

The pebble properties of novel two-phase Li 4 SiO 4 pebbles of 1 mm diameter with additions of Li 2 TiO 3 , LiAlO 2 or Li x La y TiO 3 are evaluated in this work as a function of the second phase concentration and the microstructure of the pebbles. The characterization focused on the mechanical strength, microstructure and open as well as closed porosity. Therefore crush load tests, SEM analyses as well as helium pycnometry and optical image analysis were performed, respectively. This work shows that generally additions of a second phase to Li 4 SiO 4 considerably improve the mechanical strength. It also shows that the fabrication processes have to be well-controlled to achieve high mechanical strengths. When Li 2 TiO 3 is added in different concentrations, the determinant for the crush load seems to be the open porosity of the pebbles. The strengthening effect of LiAlO 2 compared to Li 2 TiO 3 is similar, while additions of Li x La y TiO 3 increase the mechanical strength much more. Yet, Li 4 SiO 4 and Li x La y TiO 3 react with each other to a number of different phases upon sintering. In general the pebble properties of all samples are favorable for use within a fusion breeder blanket.

Wet-chemical fabrication processes are highly adaptable to a wide range of raw materials and are therefore well suited for evaluating new material compositions. Here the established emulsion method was modified to fabricate novel two-phase Li 4 SiO 4 pebbles of 1 mm diameter with additions of Li 2 TiO 3 , LiAlO 2 or Li x La y TiO 3 . As the lithium density of the latter two compounds is relatively low, only moderate contents were added. The Li 2 TiO 3 additions, however, cover the full compositional range. The fabrication process was characterized with regard to its constancy and aptness for the anticipated pebble compositions by optical pebble size measurements. Also the phase content and the elemental composition of the fabricated pebbles were analyzed by XRD and ICP-OES combined with XRF, respectively. This work shows that the emulsion method is an appropriate method to produce pebbles with the anticipated Li 2 TiO 3 and LiAlO 2 concentrations in a Li 4 SiO 4 matrix. However, Li 4 SiO 4 and Li x La y TiO 3 react with each other to a number of different phases. To evaluate the activation properties of the pebbles, FISPACT calculations with a DEMO relevant neutron source are applied as well. The addition of aluminum seems to be unfavorable for a fusion application, but moderate concentrations of lanthanum can be tolerated.

Reduced activation ferritic/martensitic steel F82H samples with tritium permeation barriers were annealed in contact with ceramic breeder pebbles at 550 °C and 700 °C for up to 32 days under purge gas. Cr2O3-formed F82H rapidly reacted to form three layers at 550 °C, and pure Fe projections grew with annealing time. Diffusion kinetics of O and Li were well fitted with Fick’s first law of diffusion. Er2O3 coatings did not react with the pebbles, but deteriorated by oxygen diffusion through the coatings. The impurity concentrations in the system and the coating thickness affect the coating compatibility in solid breeder blanket environments.

The recycling of tritium breeding materials will be necessary for any future use of nuclear fusion energy due to economical as well as ecological considerations. In the case of the solid breeder blanket concept, the ceramic pebble beds that are intended for the generation of tritium will eventually need to be restored due to depleted lithium levels as well as due to fractured pebbles, which will cause a deterioration of the pebble bed properties. It is proposed that the pebbles, which are fabricated using a melt-based process, are recycled using the same initial process, by replenishing the lithium levels and reforming the pebbles at the same time. To prove this recycling scheme, advanced ceramic pebbles were fabricated and then re-melted multiple times to prove that the reprocessing did not have any negative effect on the pebble properties and secondly, pebbles were produced with a simulated lithium burn-up and subsequently replenished by additions of LiOH to the melt. It was shown that the re-melting and lithium re-enrichment had no effect on the pebble properties, demonstrating that a melt-based process is suitable for recycling used breeder pebbles.

In advanced designs of DEMO breeding blankets with ceramic breeder, the structural material EUROFER is in direct contact with the pebbles of the ceramic breeder (Li4SiO4 + Li2TiO3) that results in a loss of constituent elements in the ceramic and the formation of a corrosion layer on EUROFER under operation relevant conditions. The impact of this corrosion attack on damage mechanisms which are significantly influenced by microstructural changes at the surface, in particular fatigue, needs to be considered in the design of affected components and is therefore investigated within the work reported here. Fatigue specimens made out of EUROFER in unconstrained contact to ceramic breeder pebbles were exposed to purge gas conditions for different durations. The chemical surface attack observed after the exposure is characterized by round stains, partly even round dimples, consisting of concentric diffusion zones which meet in case of the long exposure time forming an almost closed corrosion multi-layer. The impact of this attack on the fatigue behavior was subsequently investigated by performing strain-controlled low cycle fatigue (LCF) tests at 550 °C. To cover the scatter expected for the fatigue lifetime, a sufficient number of LCF experiments were conducted. The results show significant reduction of the fatigue lifetime, which quantitatively depends on the level of the attack/exposure time as well as the level of the applied load/strain amplitude.

The former EU reference lithium orthosilicate based breeder pebbles were exposed to neutron irradiation in the HICU (High neutron fluence Irradiation of pebble staCks for fUsion) experiment to test their stability and tritium release properties under DEMO relevant conditions. The samples, varying by three different Li-6 contents, were exposed to irradiation at two different temperatures and the pebbles were either pre-compacted or not. This second part of the post-irradiation examination is focussing on the tritium release behaviour of the ceramic breeder pebbles. The irradiation temperature has the strongest influence on the tritium release behaviour. The tritium inventory is significantly higher for samples that were irradiated at low temperatures. A clear trend regarding higher release rates with increasing Li-6 content was not observed. Tritium is released in a multi-staged process as HTO, HT or corresponding fragments. Fits based on the Wigner-Polanyi equation suggest that recombination reactions of tritium with adsorbed species on the pebble’s surface play the dominant role in the release process. However, the probability for the recombination of two adsorbed T-species on the surface seems to be too low, as no reliable signal for T2 was detected.

Lithium orthosilicate (Li4SiO4, LOS) based advanced ceramic pebbles are currently the reference material in Europe for solid tritium breeder blankets. These breeder pebbles, as the constituent of pebble beds, are not structural members but undergo cyclic thermo-mechanical compression. To withstand these operational loads, lithium metatitanate (Li2TiO3, LMT) was added as a second strengthening phase during their development at Karlsruhe Institute of Technology (KIT) in the Institute for Applied Materials Energy Storage Systems (IAM-ESS). To capture the micro scale response of the pebble bed, Discrete Element Modelling (DEM) is currently used. These simulations use the Hertzian contact model and require the crush load and Young's modulus of individual pebbles as input. In this study uniaxial compression tests were done to obtain the mechanical response of individual 500 μm and 1000 μm diameter pebbles produced by the KALOS facility built and installed at KIT IAM-ESS. Correcting the Hertzian equation to account for pebble defects, the Hertzian contact assumption was validated. The crush load increased with LMT content but the Young's modulus appeared to be independent of the LMT content. The closed porosity prevalence and variation across various batches is low and did not show any influence on the crush strength or stiffness of the pebbles.

The HICU (High neutron fluence Irradiation of pebble staCks for fUsion) experiment was performed in the High Flux Reactor (HFR) in Petten, NL, in order to irradiate candidate tritium breeder materials in a fusion relevant environment. The presented work focuses on the post-irradiation examination of the irradiated lithium orthosilicate based breeder pebbles. The pebble samples showed three different contents of Li-6 and were irradiated at two different temperatures and in mechanically constrained and unconstrained state. In this particular publication, the influences of the irradiation conditions on the pebble morphology, microstructure, porosity, and mechanical strength are addressed. The results indicate that in general a high irradiation temperature seems to be advantageous for maintaining the mechanical strength of the irradiated pebbles. A higher mechanical strength and a significantly lower closer porosity is observed for samples that were irradiated at high temperatures in comparison to pebbles that were irradiated at low temperatures. The effects on the pebble properties with respect to the Li-6 content are small in contrast to effects of the irradiation temperature. With an increased Li-6 content, no deterioration of the material properties was observed, especially for samples irradiated at high temperatures.

In the framework of the EUROfusion’s Power Plant Physics and Technology, the working package breeding blanket (BB) aims at investigating four different BB concepts for an EU demonstration fusion reactor (DEMO). One of these concepts is the helium-cooled pebble bed (HCPB) BB, which is based on the use of pebble beds of lithiated ternary compounds and Be or beryllides as tritium breeder and multiplier materials, respectively, EUROFER97 as structural steel and He as coolant. This paper aims at giving an overview of the EU HCPB BB Research and Development (R&D) being developed at KIT, in collaboration with Wigner-RCP, BUTE-INT, and CIEMAT. The paper gives an outline of the HCPB BB design evolution, state-of-the-art basic functionalities, requirements and performances, and the associated R&D activities in the areas of design, functional materials, manufacturing, and testing. In addition, attention is given also to the activities dedicated to the development of heat transfer augmentation techniques for the first wall and the corresponding testing. Due to their nature as design drivers, a brief overview in the R&D of key HCPB interfacing areas is given as well, namely, the tritium extraction and recovery system, the primary heat transfer and power conversion systems, and safety topics, as well as some specific activities regarding the integration of in-vessel systems through the BB. As concluding remarks, an outline of the standing challenges and future R&D plans is summarized.

The long-term thermal stability of advanced ceramic breeder pebbles consisting of lithium orthosilicate (Li4SiO4) and additions of lithium metatitanate (Li2TiO3) was tested in an annealing experiment at 900 °C for up to 128 days. Different gas atmospheres were used to test the influence of moisture in the purge gas. Li4SiO4 pebbles including nominally 25, 30, and 35 mol% Li2TiO3 were investigated with regard to their chemical composition, microstructure, porosity, and mechanical properties after predetermined time intervals and at the end of the experiment. No lithium loss and no secondary phases were detected. The microstructures, porosities and mechanical stabilities did not show significant changes over time. Moreover, moisture in the purge gas atmosphere has no negative influence on the material properties.

Lithium orthosilicate pebbles with 2.5 wt% excess of silica are the reference tritium breeding material for the European solid breeder test blanket modules. On the surface of the pebbles chemisorption products of carbon dioxide and water vapour (lithium carbonate and hydroxide) may accumulate during the fabrication process. In this study the influence of the chemisorption products on radiolysis of the pebbles was investigated. Using nanosized lithium orthosilicate powders, factors, which can influence the formation and radiolysis of the chemisorption products, were determined and described as well. The formation of radiation-induced defects and radiolysis products was studied with electron spin resonance and the method of chemical scavengers. It was found that the radiolysis of the chemisorption products on the surface of the pebbles can increase the concentration of radiation-induced defects and so could affect the tritium diffusion, retention and the released species.

One of the European blanket designs for ITER is the Helium Cooled Pebble Bed (HCPB) blanket. The core of the HCPB-TBM consists of so-called breeder units (BUs), which encloses beryllium as neutron multiplier and lithium orthosilicate (Li 4 SiO 4 ) as tritium breeder in form of pebble beds. After the design phase of the HCPB-BU, a non-nuclear thermal and thermo-mechanical qualification program for this device is running at the Karlsruhe Institute of Technology. Before the complex full scale BU testing, a pre-test mock-up experiment (PREMUX) has been constructed, which consists of a slice of the BU containing the Li 4 SiO 4 pebble bed. PREMUX is going to be operated under highly ITER-relevant conditions and has the following goals: (1) as a testing rig of new heater concept based on a matrix of wire heaters, (2) as benchmark for the existing finite element method (FEM) codes used for the thermo-mechanical assessment of the Li 4 SiO 4 pebble bed, and (3) in situ measurement of thermal conductivity of the Li 4 SiO 4 pebble bed during the tests. This paper describes the construction of PREMUX, its rationale and the experimental campaign planned with the device. Preliminary results testing the algorithm used for the temperature reconstruction of the pebble bed are reported and compared qualitatively with first analyses completed with the FEM codes.

The current helium cooled pebble bed (HCPB) tritium breeding blanket concept for fusion reactors includes a bed of 1 mm diameter beryllium pebbles to act as a neutron multiplier. Beryllium pebbles, fabricated by the rotating electrode method, were neutron irradiated in the HFR in Petten within the HIDOBE-01 experiment. This study presents tritium release and retention properties and data on microstructure evolution of beryllium pebbles irradiated at 630, 740, 873, 948 K up to a damage dose of 18 dpa, corresponding to a helium accumulation of about 3000 appm. The measured cumulative released activity from the beryllium pebbles irradiated at 948 K was found to be significantly lower than the calculated value. After irradiation at 873 and 948 K scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses revealed large pores or bubbles in the bulk and oxide films with a thickness of up to 8 μm at the surface of the beryllium pebbles. The radiation-enhanced diffusion of tritium and the formation of open porosity networks accelerate the tritium release from the beryllium pebbles during the high-flux neutron irradiation.

The complexity of the experimental set-up for testing a full-scaled Breeder Unit (BU) mock-up for the European Helium Cooled Pebble Bed Test Blanket Module (HCPB-TBM) has motivated to build a pre-test mock-up experiment (PREMUX) consisting of a slice of the BU in the Li4SiO4 region. This pre-test aims at verifying the feasibility of the methods to be used for the subsequent testing of the full-scaled BU mock-up. Key parameters needed for the modeling of the breeder material is also to be determined by the Hot Wire Method (HWM). The modeling tools for the thermo-mechanics of the pebble beds and for the mock-up structure are to be calibrated and validated as well. This paper presents the setting-up of PREMUX in the L-STAR/LL facility at the Karlsruhe Institute of Technology. A key requirement of the experiments is to mimic the neutronic volumetric heating. A new heater concept is discussed and compared to several conventional heater configurations with respect to the estimated temperature distribution in the pebble beds. The design and integration of the thermocouple system in the heater matrix and pebble beds is also described, as well as other key aspects of the mock-up (dimensions, layout, cooling system, purge gas line, boundary conditions and integration in the test facility). The adequacy of these methods for the full-scaled BU mock-up is discussed and the next steps that follow PREMUX set-up are shown.

Within the European Union, slightly hyperstoichiometric lithium orthosilicate has evolved as one of the candidate solid breeder materials for the helium cooled pebble bed blanket, which will be tested in ITER. In the past, several long-term irradiation experiments proved that lithium orthosilicate shows excellent tritium release behavior when purged with helium with 0.1% hydrogen. In this work, short-term irradiation experiments at the High Flux Reactor in Petten with two standard pebble qualities, as-received and heat-treated lithium orthosilicate were carried out to investigate possible differences in tritium release. Since the surface of the pebbles may play a significant role, especially for short-term irradiation, and the mechanism of desorption from the surface determines the chemical form and very likely the release rate of tritium, the aim of this work is to link the chemical composition of the surface to the Thermal Programmed Desorption (TPD) tritium release experiments. Therefore X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry were applied to characterize the surface of the unirradiated pebbles and to obtain sputter depth profiles of up to 800 nm. In addition, X-ray diffractometry was used to determine the composition of phases of the samples before and after irradiation.

For the fabrication of Li-6 enriched ceramic breeder materials for ITER, the availability of Li-6 enriched compounds is limited, and metallic Li-6 is the most widely available compound. As metallic lithium cannot be used directly in ceramic fabrication processes, we investigated different syntheses to obtain lithium orthosilicate or lithium metatitanate directly from molten lithium. In exothermic reactions of molten lithium with silicon, silica, or titania, several intermediate or precursor phases were observed under argon that could easily be transformed to the desired ceramic phases by a subsequent heat treatment under air. The reaction steps and the resulting phases were studied by differential scanning calorimetry and X-ray diffractometry. The synthesis from lithium and silicon seems to be especially suited for the production of larger quantities and has the advantage that silicon is available with a very high grade of purity.

The solid breeder blanket concept proposed by the European Union features the tritium breeding ceramics as pebble beds inside several breeder units. The pebble bed will not take part in the structural rigidity of a breeder unit. Still the pebbles need to withstand forces originating from thermal expansion mismatches and neutron irradiation. A designated breeder ceramic for this concept is lithium orthosilicate with a slight surplus of silica. It has been demonstrated that lithium orthosilicate can be processed by melt spraying, which is favorable to other processes in terms of recycling. This work summarizes changes to the process and investigations of the current limitations that have to be overcome to enhance not only the mechanical properties of the pebbles, but also the yield of the process. A key feature of the improvements is to control the forming of the single pebbles more precisely than in the past. Thereby, not only the generation of pores should be avoided, but also the size distribution of the pebbles should be more accurately controlled.

Lithium orthosilicate (Li4SiO4) pebbles with 2.5 wt.% excess of silicon dioxide (SiO2) are the European Union's designated reference tritium breeding ceramics for the Helium Cooled Pebble Bed (HCPB) Test Blanket Module (TBM). However, the latest irradiation experiments showed that the reference Li4SiO4 pebbles may crack and form fragments under operation conditions as expected in the HCPB TBM. Therefore, it has been suggested to change the chemical composition of the reference Li4SiO4 pebbles and to add titanium dioxide (TiO2), to obtain lithium metatitanate (Li2TiO3) as a second phase. The aim of this research was to investigate the formation and accumulation of radiation-induced defects (RD) and radiolysis products (RP) in the modified Li4SiO4 pebbles with different contents of TiO2 for the first time, in order to estimate and compare radiation stability. The reference and the modified Li4SiO4 pebbles were irradiated with accelerated electrons (E = 5 MeV) up to 5000 MGy absorbed dose at 300–990 K in a dry argon atmosphere. By using electron spin resonance (ESR) spectroscopy it was determined that in the modified Li4SiO4 pebbles, several paramagnetic RD and RP are formed and accumulated, like, E' centres (SiO33−/TiO33−), HC2 centres (SiO43−/TiO3−) etc. On the basis of the obtained results, it is concluded that the modified Li4SiO4 pebbles with TiO2 additions have comparable radiation stability with the reference pebbles.

Based on a KIT–CIEMAT collaboration on the radiation damage effects of light ions sorption/desorption in ceramic breeder materials, candidate materials for the ITER EU TBM were tested for their outgassing behavior as a function of temperature and radiation. Lithium orthosilicate based pebbles with different metatitanate contents and pellets of the individual oxide components were exposed to a deuterium atmosphere at room temperature. Then the thermally induced release of deuterium gas was registered up to 800 °C. This as-received behavior was studied in comparison with that after exposing the deuterium-treated samples to 4 MGy total dose of gamma radiation. The thermal desorption spectra reveal differences in deuterium sorption/desorption behavior depending on the composition and the induced ionizing damage. In these breeder candidates, strong desorption rate at approx. 300 °C takes place, which slightly increases with increasing amount of the titanate second phase. For all studied materials, ionizing radiation induces electronic changes disabling a number of trapping centers for D 2 adsorption.

Crushing strength of the breeder materials (lithium orthosilicate, $\rm{Li_4SiO_4}$ or OSi) in the form of pebbles to be used for EU solid breeder concept is investigated. The pebbles are fabricated using a melt-spray method and hence a size variation in the pebbles produced is expected. The knowledge of the mechanical integrity (crush strength) of the pebbles is important for a successful design of breeder blanket. In this paper, we present the experimental results of the crush (failure) loads for spherical OSi pebbles of different diameters ranging from $250~\mu$m to $800~\mu$m. The ultimate failure load for each size shows a Weibull distribution. Furthermore, the mean crush load increases with increase in pebble diameter. It is also observed that the level of opacity of the pebble influences the crush load significantly. The experimental data presented in this paper and the associated analysis could possibly help us to develop a framework for simulating a crushable polydisperse pebble assembly using discrete element method., Comment: 4 Figures, 8 pages

International audience; As candidate tritium breeder materials for use in the ITER helium cooled pebble bed, ceramic multiphasic compounds lying in the region of the quasi-binary lithium metatitanate-lithium orthosilicate system may exhibit mechanical and physical advantages relative to single phase materials. Here we present an organometallic solution-based synthesis procedure for the low-temperature fabrication of compounds in the Li 2 TiO 3-Li 4 SiO 4 region and investigate phase stability and transformations through temperature varied X-ray diffraction and scanning calorimetry. Results demonstrate that the metatitanate and metasilicate phases Li 2 TiO 3 and Li 2 SiO 3 readily crystallise in nanocrystalline form at temperatures below 180°C. Lithium deficiency in the region of 5% results from Li sublimation from Li 4 SiO 4 and/or from excess Li incorporation in the metatitanate phase and brings about a stoichiometry shift and product compounds with mixed lithium orthosilicate/ metasilicate content towards the Si rich region and predominantly Li 2 TiO 3 content towards the Ti rich region. Above 1150°C the transformation of monoclinic to cubic γ-Li 2 TiO 3 disordered solid-solution occurs while the melting of silicate phases indicates a likely monotectic type system with a solidus line in the region 1050°-1100°C. Synthesis procedures involving a lithium chloride precursor are not likely to be a viable option for breeder pebble synthesis as this route was found to yield materials with a more significant Li-deficiency exhibiting the crystallisation of the Li 2 TiSiO 5 phase at intermediate compositions.https://doi.org/10.1016/j.jnucmat.2014.09.028; En tant que matériaux sélectionneurs de tritium candidats à utiliser dans le lit de galets refroidi à l'hélium ITER, les composés céramiques multiphasiques situés dans la région du système métasitanate de lithium-orthosilicate de lithium quasi-binaire peuvent présenter des avantages mécaniques et physiques par rapport aux matériaux monophasés. Nous présentons ici une procédure de synthèse à base de solutions organométalliques pour la fabrication à basse température de composés de la région Li 2 TiO 3-Li 4 SiO 4 et étudions la stabilité de phase et les transformations par diffraction des rayons X à température variée et calorimétrie à balayage. Les résultats démontrent que les phases de métatitanate et de métasilicate, Li 2 TiO 3 et Li 2 SiO 3, cristallisent facilement sous forme nanocristalline à des températures inférieures à 180 ° C. Une déficience en lithium dans la région de 5% résulte de la sublimation de Li de Li 4 SiO 4 et / ou de l'incorporation excessive de Li dans la phase de métatitanate et entraîne un déplacement de la stoechiométrie et des composés du produit avec une teneur mixte en orthosilicate de lithium / métasilicate vers la région riche en Si teneur en Li 2 TiO 3 principalement vers la région riche en Ti. Au-dessus de 1150 ° C, la transformation de la solution solide désordonnée en γ-Li 2 TiO 3 monoclinique en cubique se produit, tandis que la fusion des phases silicatées indique un système de type monotectique probable avec une ligne solide située dans la région allant de 1050 à 1100 ° C. Les procédures de synthèse faisant appel à un précurseur de chlorure de lithium ne constitueront probablement pas une option viable pour la synthèse de galets reproducteurs, car il a été constaté que cette voie conduisait à des matériaux présentant un déficit en Li plus important, présentant la cristallisation de la phase Li 2 TiSiO 5 dans des compositions intermédiaireshttps://doi.org/10.1016/j.jnucmat.2014.09.028

In the solid Breeder Blanket (BB) concepts both tritium release and heat recovery depend on the thermal performances of the breeding zone. Within the RD to this end the line heat source probe method was employed together with differential scanning calorimetry. An experimental facility, based on the line heat source probe method, was devised for the investigation of the thermal diffusivity of granular beds at breeder blanket relevant temperatures, mechanical state, purge gas type and pressure. Besides the experimental approach, literature values were used to estimate the specific heat capacity of the breeder materials starting from the specific heat capacity of the constituent compounds based on the mole fraction. In addition to the thermal diffusivity and heat capacity, a preliminary insight on the phase transitions of the reference and advanced ceramic breeder beds is given.