Search

The use of low-concentration factor ultrafiltered (LCF-UF) milk for cheesemaking has become popular in recent years. Research on using LCF-UF milk to make low-moisture part-skim (LMPS) Mozzarella manufacture is limited due to concerns about the negative impact of the higher casein content on functional properties, such as melt and stretch. Pre-acidification (PA) (reflects acid added to milk before the addition of the starter culture) has been used in low-fat and nonfat Mozzarella cheeses to lower calcium levels and improve their texture and melting properties. We explored the use of PA to reduce the insoluble calcium content of cheese (calcium that is a crosslinking material for the casein proteins) and its impact on the functionality of LMPS Mozzarella made from high casein (4.2%) milk. Seven vats of LMPS Mozzarella, with a control (no PA), 2 pH values for PA (6.40 and 6.00) and 3 different acidification methods (use of acetic, citric, or carbonic acid from carbon dioxide) were evaluated for their impact on solubilization of colloidal calcium phosphate during LMPS manufacture. Composition, proteolysis, microstructural and functional changes in the LMPS cheeses were monitored during 90 d of refrigerated storage. All cheeses had similar composition except for the cheese made with milk PA with carbonic acid, which had a lower fat-in-dry matter probably due to foaming observed in this sample during the gas sparging. The cheese made with milk PA with citric acid to pH 6.00 had the lowest amount of total and insoluble calcium compared with other cheeses at all steps during cheese manufacture and storage, likely due to the calcium chelating ability of citric acid. The cheese that was made with milk PA with citric acid to pH 6.40 had a trend of slightly lower (not significant) total and insoluble calcium during cheese manufacture compared with other cheeses that were made with milk PA to pH 6.40. The pH value in all the cheeses remained similar throughout 90 d of storage, whereas the cheese that was made with milk PA with citric acid to pH 6.00 had the lowest pH values during storage. Treatment significantly (P < 0.05) impacted instrumental hardness, the maximum loss tangent during heating, the melting temperature and the storage modulus values measured at 70°C. Proteolysis was not impacted by treatment suggesting that typical aging should occur. Cheese that was PA with citric acid to pH 6.00 initially had lower maximum loss tangent values and higher hardness, possibly due to the lower pH value of this cheese. The performance of cheeses on pizza was assessed using Sensory Spectrum® method and quantitative descriptive analysis. The PA of cheese milk with citric acid helped to reduce the insoluble Ca level and at 30 and 90 d of storage, these cheeses had lower first chew hardness, lower chewiness, and lower strand thickness values compared with other cheeses. The use of PA could help improve the functionality of LMPS Mozzarella made from milk high in casein with citric acid being the most efficient in dissolving the insoluble calcium from casein., (The Authors. Published by Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).)

Residual lipids (RL) in whey protein isolate (WPI) are detrimental to optimal functional applications (e.g., foaming and low turbidity) and contribute to off-flavor development during powder storage. The objective of this research was to prepare an experimental WPI by removing RL without using the traditional microfiltration process and compare its properties with commercially available WPI made using microfiltration and some other whey powders. We hypothesize that by adjusting the pH of whey to <5.0, we would be close to the isoelectric point of any remaining denatured proteins (DP) and phospholipoproteins (PLP), and therefore reduce electrostatic repulsion between these molecules. Furthermore, demineralization of the acidified whey protein solution by UF combined with diafiltration (DF) should reduce ionic hindrance to aggregation and thereby help with the aggregation of these DP as well as most RL; centrifugation or clarification could be used to remove these materials. Calcium should also be more extensively removed by this approach, which should improve the heat stability of the experimental WPI. Demineralization was achieved on a pilot scale by acidifying liquid (cheese) whey protein concentrate containing 34% protein (WPC-34) to pH 4.5 using HCl, and UF of the whey protein solution along with extensive DF using acidified (pH ∼3.5) reverse osmosis filtered water. Demineralized whey protein solution was adjusted to various combinations of pH (4.1-4.9), conductivities (500-2,000 μS/cm), and protein concentrations (1%-7%) and then centrifuged at 10,000 × g for 10 min. The effective sedimentation (precipitation) of RL in these treatments was estimated by measuring the turbidity of the supernatants. Maximum precipitation was observed at pH 4.5 to 4.7. Reducing conductivity via UF/DF increased the precipitation of RL due to reduced ionic hindrance to aggregation. Maximum sedimentation of RL was observed at protein concentrations ≤3% because of a higher density difference between the precipitate and serum phase. Analysis by sodium dodecyl sulfate polyacrylamide gel electrophoresis analysis confirmed the sedimentation of phospholipoproteins, caseins, and DP upon isoelectric precipitation at pH ∼4.5, while native whey proteins or undenatured whey proteins remained soluble in the supernatant, unaffected by the pretreatment. To scale up the process, 750 L of fluid WPC-34 was acidified and demineralized by UF (volume concentration factor = 1.35) and DF until the permeate solids reached 0.1% (when desired demineralization was achieved), clarified using a pilot-scale desludging clarifier to remove RL, neutralized, ultrafiltered to concentrate the protein, and then spray-dried to produce an experimental WPI (91% protein and 1.8% fat on a dry basis [db]). In another trial, demineralized UF concentrate was clarified by gravity sedimentation and the supernatant was neutralized, ultrafiltered, and spray-dried to produce a second experimental WPI (91% protein and <1% fat db). These experimental WPI powders were compared with several commercially available WPI powders to assess functional properties such as solubility, heat stability, foamability and foam strength, gelation, and sensory attributes over accelerated storage. Experimental WPI had excellent functional properties, had low turbidity, were highly heat stable, and only developed very slight-to-slight off-flavors upon accelerated storage, and their properties were comparable to the WPI manufactured commercially using microfiltration even after accelerated storage., (The Authors. Published by Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).)

The manufacturing method of string cheese is similar to mozzarella, but the hot curd is extruded through narrow tubes or pipes, which align the protein fibers that provide the characteristic ability for consumers to pull strings from this cheese. Firmness is another important performance attribute for consumers who just bite into the string cheese without peeling off strings. There have only been a few studies on string cheese, but it is known that stringiness and firmness decrease during prolonged storage, which is a particular challenge for exporting string cheese. We explored 2 treatments to try to retain the stringiness and firmness of string cheese for longer storage periods. The techniques used were high-pressure processing (HPP; 600 MPa for 3 min) and reduced storage temperature (0°C). In other cheese varieties, these techniques have helped extend the performance shelf life. We tested these techniques using the 2 main types of commercial string cheese: direct acid string cheese (DASC) and cultured string cheese (CSC), which were obtained from 2 different manufacturing facilities. The DASC had higher fat (∼2.2%) and higher pH values (∼0.2 units) compared with the CSC. The CSC had higher protein content (∼3.4%), higher insoluble calcium content (∼8 mg insoluble Ca/g protein) and higher texture profile analysis (TPA) hardness values (∼4 N) compared with the DASC. Due to the compositional differences, the 2 varieties were statistically analyzed separately for all other attributes. In both cheese types, HPP caused an immediate reduction in stringiness, some solubilization of insoluble calcium, and a slight increase in the cheese pH values. High-pressure processing also caused a slight increase in TPA hardness of the CSC samples until 14 d (possibly due to a slight increase in cheese pH). The use of the 0°C storage temperature reduced proteolysis and helped retain firmness during storage. Low-temperature storage could help extend the performance shelf life of string cheese by a couple of months, but HPP was not suitable, as the process caused an immediate reduction in stringiness due to the disruption of the matrix induced by the HPP treatment., (The Authors. Published by Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).)

Due to its versatility and shelf stability, process cheese is gaining interest in many developing countries. The main structural component (base) of most processed cheese formulations is young Cheddar cheese that has high levels of intact casein. Exporting natural Cheddar cheese base from the United States to distant overseas markets would require the aging process to be slowed or reduced. As Cheddar cheese ripens, the original structure is broken down by proteolysis and solubilization of insoluble calcium phosphate. We explored the effect of varying rennet levels (we also used a less proteolytic rennet) and application of high-pressure processing (HPP) to Cheddar cheese, as we hoped these treatments might limit proteolysis and concomitant loss of intact casein. To try to retain high levels of insoluble Ca, all experimental cheeses were made with a high-draining pH and from concentrated milk. To compare our intact casein results with current practices, we manufactured a Cheddar cheese that was prepared according to typical industry methods (i.e., use of unconcentrated milk, calf chymosin [higher levels], and low draining pH value [∼6.2]). All experimental cheeses were made from ultrafiltered milk with protein and casein contents of ∼5.15% and 4.30%, respectively. Three (low) rennet levels were used: control (38 international milk clotting units/mL of rennet per 250 kg of milk), and 25% and 50% reduced from this level. All experimental cheeses had similar moisture contents (∼37%) and total Ca levels. Four days after cheese was made, half of the experimental samples from each vat underwent HPP at 600 MPa for 3 min. Cheddar cheese functionality was monitored during aging for 240 d at 4°C. Cheddar cheese base was used to prepare process cheese after aging for 14, 60, 120, 180, and 240 d. Loss tangent (LT) values of cheese during heating were measured by small strain oscillatory rheology. Intact casein levels were measured using the Kjeldahl method. Acid or base titrations were used to determine the buffering capacity and insoluble Ca levels as a percentage of total Ca. The LT max values (an index of meltability) in process cheese increased with aging for all the cheese bases; the HPP treatment significantly decreased LT max values of both base (natural) and process cheeses. All experimental cheeses had much higher levels of intact casein compared with typical industry-make samples. Process cheese made from the experimental treatments had visually higher stretching properties than process cheese made from Cheddar with the typical industry-make procedure. Residual rennet activity was not affected by rennet level, but the rate of proteolysis was slightly slower with lower rennet levels. The HPP treatment of Cheddar cheese reduced residual rennet activity and decreased the reduction of intact casein levels. The HPP treatment of Cheddar cheese resulted in process cheeses that had slightly higher hardness values, lower LT max values, and retained higher storage modulus values at 70°C. We also observed that the other make procedures we used in all experimental treatments (i.e., using a less proteolytic chymosin, using a concentrated cheese milk, and maintaining a high draining pH value) had a major effect on retaining high levels of intact casein., (© 2024, The Authors. Published by Elsevier Inc. and Fass Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).)

Whey protein phospholipid concentrate (WPPC) contains high amounts of phospholipids (PL; 4.5 ± 1%) but there is interest in further enriching the PL content for nutritional and functional applications. Chemical methods were unsuccessful in separating PL from proteins due to the presence of protein-fat aggregates. Instead, we explored hydrolysis of the proteins to peptides with the objective of removing peptides, thereby concentrating the PL fraction. We used microfiltration (MF) with a pore size of 0.1 µm to help reduce protein/peptide retention. Hydrolyzing proteins should facilitate passage of low molecular weight peptides through the MF membrane, while concentrating fat and PL in the MF retentate. Bench-top experiments were performed to select the proteolytic enzyme that resulted in the most extensive hydrolysis of proteins in WPPC from among 5 different commercial proteases. Sodium dodecyl sulfate-PAGE analysis was performed to measure the extent of protein hydrolysis over a period of 4 h. Alcalase enzyme was found to exhibit the highest proteolytic activity at conditions of pH 8 and temperature 55°C. The intensity of major protein bands (milkfat globule membrane proteins, caseins, β-lactoglobulin) in WPPC decreased in sodium dodecyl sulfate-PAGE profiles as hydrolysis progressed, along with the appearance of low molecular weight bands. Pilot-scale MF production, coupled with diafiltration (DF), of the hydrolyzed sample aided in the removal of peptides that caused an ~18% reduction in protein content with the final retentate having a total PL content of 9.3% dry basis (db) with protein and fat contents at approximately 43.8 ± 0.4% (db) and 48.9 ± 1.2% (db), respectively. The MF permeate had minimal fat content, indicating that there was no transmission of lipids or PL through the membrane during the MF/DF process. Confocal laser scanning microscopy and particle size analysis of enzyme hydrolyzed solution revealed that protein aggregates were still present after 1 h of hydrolysis. Complete removal of proteins and peptides was not achieved by this process, suggesting that a combination of enzymes would be needed for further hydrolysis of protein aggregates in WPPC solution to further enrich the PL content., (© 2023.)

High protein levels in yogurt, as well as the presence of denatured whey proteins in the milk, lead to the development of firm gels that can make it difficult to formulate a fluid beverage. We wanted to prepare high-protein yogurts and explore the effects of using micellar casein isolate (MCI), which was significantly depleted in whey protein by microfiltration. Little is known about the use of whey protein-depleted milk protein powders for high-protein yogurt products. Microfiltration also depletes soluble ions, in addition to whey proteins, and so alterations to the ionic strength of rehydrated MCI dispersions were also explored, to understand their effects on a high-protein yogurt gel system. Yogurts were prepared at 8% protein (wt/wt) from MCI or nonfat dry milk (NDM). The NDM was dispersed in water, and MCI powders were dispersed in water (with either low levels of added lactose to allow fermentation to achieve the target pH, or a high level to match the lactose content of the NDM sample) or in ultrafiltered (UF) milk permeate to align its ionic strength with that of the NDM dispersion. Dispersions were then heated at 85°C for 30 min while stirring, cooled to 40°C in an ice bath, and fermented with yogurt cultures to a final pH of 4.3. The stiffness of set-style yogurt gels, as determined by the storage modulus, was lowest in whey protein-depleted milk (i.e., MCI) prepared with a high ionic strength (UF permeate). Confocal laser scanning microscopy and permeability measurements revealed no large differences in the gel microstructure of MCI samples prepared in various dispersants. Stirred yogurt made from MCI that was prepared with low ionic strength showed slow rates of elastic bond reformation after stirring, as well as slower increases in cluster particle size throughout the ambient storage period. Both the presence of denatured whey proteins and the ionic strength of milk dispersions significantly affected the properties of set and stirred-style yogurt gels. Results from this study showed that the ionic strength of the heated milk dispersion before fermentation had a large influence on the gelation pH and strength of acid milk gels, but only when prepared at high (8%) protein levels. Results also showed that depleting milk of whey proteins before fermentation led to the development of weak yogurt gels, which were slow to rebody and may be better suited for preparing cultured milk beverages where low viscosities are desirable., (The Authors. Published by Elsevier Inc. and Fass Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).)

A growing number of companies within the cheese-making industry are now using high-protein (e.g., 4-5%) milks to increase cheese yield. Previous studies have suggested that cheeses made from high-protein (both casein and whey protein; WP) milks may ripen more slowly; one suggested explanation is inhibition of residual rennet activity due to elevated WP levels. We explored the use of microfiltration (MF) to concentrate milk for cheese-making, as that would allow us to concentrate the casein while varying the WP content. Our objective was to determine if reducing the level of WP in concentrated cheese milk had any impact on cheese characteristics, including ripening, texture, and nutritional profile. Three types of 5% casein standardized and pasteurized cheese milks were prepared that had various casein:true protein (CN:TP) ratios: (a) control with CN:TP 83:100, (b) 35% WP reduced, 89:100 CN:TP, and (c) 70% WP reduced, 95:100 CN:TP. Standardized milks were preacidified to pH 6.2 with dilute lactic acid during cheese-making. Composition, proteolysis, textural, rheological, and sensory properties of cheeses were monitored over a 9-mo ripening period. The lactose, total solids, total protein, and WP contents in the 5% casein concentrated milks were reduced with increasing levels of WP removal. All milks had similar casein and total calcium levels. Cheeses had similar compositions, but, as expected, lower WP levels were observed in the cheeses where WP depletion by MF was performed on the cheese milks. Cheese yield and nitrogen recoveries were highest in cheese made with the 95:100 CN:TP milk. These enhanced recoveries were due to the higher fraction of nitrogen being casein-based solids. Microfiltration depletion of WP did not affect pH, sensory attributes, or insoluble calcium content of cheese. Proteolysis (the amount of pH 4.6 soluble nitrogen) was lower in control cheeses compared with WP-reduced cheeses. During ripening, the hardness values and the temperature of the crossover point, an indicator of the melting point of the cheese, were higher in the control cheese. It was thus likely that the higher residual WP content in the control cheese inhibited proteolysis during ripening, and the lower breakdown rate resulted in its higher hardness and melting point. There were no major differences in the concentrations of key nutrients with this WP depletion method. Cheese milk concentration by MF provides the benefit of more typical ripening rates., (The Authors. Published by Elsevier Inc. and Fass Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).)

Shelf-stable cultured milk beverages that have high protein levels can be difficult to successfully manufacture. With increasing protein level, rapid phase separation and gel formation occur in cultured beverages, which may not be prevented even with the inclusion of stabilizers such as high methoxy (HM) pectin. To limit protein aggregation in cultured milk beverages we investigated micellar casein as an interesting alternative to milk, due to the absence of whey proteins, which can contribute to increased gel strength in cultured products. In this study, micellar casein dispersed in ultrafiltered milk permeate was fermented to pH 4.1, blended with HM pectin, homogenized, thermally processed, and bottled for storage at ambient temperature for 6 mo. Utilizing response surface methodology with a central composite rotatable design, the protein and pectin contents were varied between 5 and 9% and 0.0 and 1.0%, respectively. The elastic modulus, loss tangent, and yield stress of these beverages were measured during storage to observe the extent of bond restructuring, whereas particle size and visual phase separation were measured to determine stability. Response variables were measured initially after thermally processing the beverages, and after 1 and 6 mo of storage at ambient temperature. All samples quickly formed gels after homogenizing, regardless of the pectin level. The stiffness (elastic modulus) of all samples increased throughout storage and was determined mainly by the protein content; however, the growth of elastic bonds over time was slowed with high levels of pectin. At 6 mo of storage, yield stress values were significantly lower for beverages with <7.5% protein when they were stabilized with ≥0.85% pectin. Prediction models for visual phase separation in beverages stored for 6 mo were significantly affected by the protein content, with increasing instability at lower protein levels. Models were used to identify optimal protein (<7.5%) and pectin (≥0.85%) concentrations to minimize the stiffness of gels during ambient storage. Samples in this optimized region were predicted to have low yield stress values and were easily fluidized by gentle shaking of the bottle at 6 mo., (© 2022, The Authors. Published by Elsevier Inc. and Fass Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).)

Dairy-derived lipids such as phospholipids (PL) have been gaining interest due to their functional and nutritional properties. Our research goal was to develop a separation process (nonsolvent based) to produce an enriched dairy lipid fraction from whey protein phospholipid concentrate (WPPC). Various chemical pretreatments (i.e., adjustment of pH, calcium, or temperature) were applied to rehydrated commercial WPPC solutions. These treatments were done on a bench-top scale to aid in the precipitation of proteins or PL. The chemically treated solutions were centrifuged and fractionated into the following 3 layers: (1) top fat layer, (2) supernatant in the middle zone, and (3) sediment at the bottom of the centrifuge tubes. The thickness and size of the layers varied with the treatment parameters. Compositional analysis of each layer showed that the proteins, fat, and PL always appeared to fractionate in similar proportions. The proteins in each layer were characterized using sodium dodecyl sulfate-PAGE under reducing and nonreducing conditions. Different proteins including whey proteins, caseins, and milk fat globule membrane proteins and lipoproteins were identified, and no specific type of protein had an affinity for either the top or bottom layer. All types of proteins were present in each of the layers after centrifugation, and there were no major differences in fractionation of the proteins between layers with respect to the chemical treatment applied. The microstructure of protein and fat in WPPC was investigated using confocal laser scanning microscopy. Dual staining of the rehydrated WPPC solution with Fast Green FCF (proteins) and Nile Red (lipids) showed the presence of very large protein aggregates that varied in size from 20 to 150 μm, with fat trapped within these aggregates. The confocal laser scanning microscopy images of liquid WPPC revealed fine strands of a weak protein network surrounding the fat globules. This indicated that there were specific interactions between the proteins, as well as between the fat and proteins in WPPC. Sodium dodecyl sulfate treatment was performed to understand the nature of the interactions between protein and fat. We found that about 35% of the fat present in WPPC was in the form of free fat, which was only physically entrapped within the protein aggregates. The remaining fat had some form of association with the proteins in WPPC. Other fractionation techniques would be needed to obtain an enriched dairy lipid fraction., (Copyright © 2021 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

In the manufacture of cream cheese, sweet cream and milk are blended to prepare the cream cheese mix, although other ingredients such as condensed skim milk and skim milk powder may also be included. Whey cream (WC) is an underutilized fat source, which has smaller fat droplets and slightly different chemical composition than sweet cream. This study investigated the rheological and textural properties of cream cheeses manufactured by substituting sweet cream with various levels of WC. Three different cream cheese mixes were prepared: control mix (CC; 0% WC), cream cheese mixes containing 25% WC (25WC; i.e., 75% sweet cream), and cream cheese mixes with 75% WC (75WC; i.e., 25% sweet cream). The CC, 25WC, and 75WC mixes were then used to manufacture cream cheeses. We also studied the effect of WC on the initial step in cream cheese manufacture (i.e., the acid gelation process monitored using dynamic small amplitude rheology). Acid gels were also prepared with added denatured whey proteins or membrane proteins/phospholipids (PL) to evaluate how these components affected gel properties. The rheological, textural, and sensory properties of cream cheeses were also measured. The WC samples had significantly higher levels of PL and insoluble protein compared with sweet cream. An increase in the level of WC reduced the rate of acid gel development, similar to the effect of whey phospholipid concentrate added to mixes. In cream cheese, an increase in the level of added WC resulted in significantly lower storage modulus values at temperatures <20°C. Texture results, obtained from instrumental and sensory analyses, showed that high level of WC resulted in significantly lower firmness or hardness values and higher stickiness compared with cream cheeses made with 25WC or CC cream cheeses. The softer, less elastic gels or cheeses resulting from the use of high levels of WC are likely due to the presence of components such as PL and proteins from the native milk fat globule membrane. The use of low levels of WC in cream cheese did not alter the texture, whereas high levels of WC could be used if manufacturers want to produce more spreadable products., (Copyright © 2021 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

The pH of cheese is determined by the amount of lactose fermented and the buffering capacity of the cheese. The buffering capacity of cheese is largely determined by the protein contents of milk and cheese and the amount of insoluble calcium phosphate in the curd, which is related to the rate of acidification. The objective of this study was to standardize both the lactose and casein contents of milk to better control final pH and prevent the development of excessive acidity in Cheddar cheese. This approach involved the use of low-concentration factor ultrafiltration of milk to increase the casein content (∼5%), followed by the addition of water, ultrafiltration permeate, or both to the retentate to adjust the lactose content. We evaluated milks with 4 different lactose-to-casein ratios (L:CN): 1.8 (control milk), 1.4, 1.1, and 0.9. All cheesemilks had similar total casein (2.3%) and fat (3.4%) contents. These milks were used to make milled-curd Cheddar cheese, and we evaluated cheese composition, texture, functionality, and sensory properties over 9 mo of ripening. Cheeses made from milks with varying levels of L:CN had similar moisture, protein, fat, and salt contents, due to slight modifications during manufacture (i.e., cutting the gel at a smaller size than control) as well as control of acid development at critical steps (i.e., cutting the gel, whey drainage, salting). As expected, decreasing the L:CN led to cheeses with lower lactic acid, residual lactose, and insoluble Ca contents, as well as a substantial pH increase during cheese ripening in cheeses. The L:CN ratio had no significant effect on the levels of primary and secondary proteolysis. Texture profile analysis showed no significant differences in hardness values during ripening. Maximum loss tangent, an index of cheese meltability, was lower until 45 d for the L:CN 1.4 and 0.9 treatments, but after 45 d, all reduced L:CN cheeses had higher maximum loss tangent values than the control cheese (L:CN 1.8). Sensory analyses showed that cheeses made from milks with reduced L:CN contents had lower acidity, sourness, sulfury notes, and chewdown cohesiveness. Standardization of milk to a specific L:CN ratio, while maintaining a constant casein level in the milk, would allow Cheddar cheese manufacturers to have tighter control of pH and acidity., (Copyright © 2021 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Some European dairies use low concentration factor microfiltration (MF) in their cheese plants. Removal of whey protein (WP) from milk before cheesemaking using microfiltration without concentration provides the opportunity to produce a value-added by-product, milk-derived whey. However, few studies have focused on the effects on cheese properties caused by the depletion of WP from cheese milk. Most studies have concentrated cheese milk using MF in addition to depletion of WP. In our approach, cheese milk was not concentrated during WP depletion using MF. We wanted to quantify residual WP levels in cheese made from MF milk and to explore whether WP depletion from milk would influence functionality, nutritional profile, and cheese quality during ripening. Casein (CN) contents for all milks were kept at ∼2.5%, to eliminate the confounding factor of concentration of CN, which was observed in some previous MF studies. Cheese milks had similar ratios of CN to fat. Three standardized milks were produced with various CN:true protein (TP) ratios: (a) control with a CN:TP ratio of 83:100, (b) 35% WP depletion, 89:100 CN:TP, and (c) 70% WP depletion, 95:100 CN:TP. Cheddar cheeses were made from MF milk with various WP depletion levels and aged for 9 mo, and their functionality was evaluated during ripening. We found no major differences in cheese composition or pH values between samples. Cheese yield, solids recovery, and nitrogen recovery were slightly higher in the 95:100 CN:TP cheeses compared with the control. These enhanced recoveries reflect that MF-treated milk started with a higher fraction of CN-based protein solids, rather than WP solids. The standardized milk from the 95:100 CN:TP treatment also had a slightly higher fat content compared with the control, likely helping to increase cheese yield. Rheological properties of cheeses during heating were similar between treatments. Hardness initially decreased with age for all cheeses due to proteolysis or solubilization, or both, of calcium phosphate. Maximum loss tangent (LT), an index of cheese meltability, was slightly lower for the control cheese until 30 d of ripening, but after 30 d, all treatments exhibited similar maximum LT values. The temperature where LT = 1 (crossover temperature), an index of softening point during heating, was slightly lower for MF cheese compared with the control cheeses during ripening. Microfiltration treatment had no significant influence on proteolysis. Sensory properties were similar between the cheeses, except for bitterness. Bitterness intensity was slightly lower in the MF cheeses than in the control cheeses and increased in all cheeses during ripening. We detected no major differences in the concentrations of key nutrients or vitamins between the various cheeses. Depletion of WP in cheese milk by MF did not negatively affect cheese quality, or its nutritional profile, and resulted in similar cheesemaking yields., (Copyright © 2020 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Stabilizers are routinely added during cream cheese manufacture to help prevent syneresis during storage. We investigated how different types of stabilizers affected the texture, rheology, and sensory properties of cream cheese. Cream cheeses were manufactured with 0.33% xanthan gum (XG), locust bean gum (LBG), guar gum (GG), or a combination (CBN) of these 3 stabilizers (0.11% of each). Rheological properties of solutions of the individual stabilizers and their combination (equal amounts) were also determined under conditions similar to the aqueous phase of cream cheese (0.6% gum, 1.8% NaCl, and pH 5). Dynamic small amplitude rheological properties of the cream cheeses were measured during heating from 5 to 80°C at the rate of 1°C/min and cooling at the same rate (because most cream cheese is hot packed/filled before cooling). Measured rheological parameters included storage modulus (G') and loss tangent. Hardness of cream cheeses was determined by texture profile analysis. Quantitative spectrum descriptive sensory analysis was also performed. Distinct differences were observed between the rheological properties of solutions of the individual stabilizers and the CBN containing all the stabilizers. Results showed that CBN solution formed a strong, thermally reversible gel due to synergistic interaction between stabilizers, whereas XG solution formed a weak gel that was not greatly affected by temperature. Solutions of LBG and GG behaved rheologically as entangled polymer solutions. In the high-temperature (>35°C) region, cream cheeses made with XG and CBN showed higher G' values compared with other cream cheeses. The G' values were higher for XG- and CBN-stabilized cream cheeses than LBG- and GG-stabilized cream cheeses at several temperature regions during the cooling cycle. The CBN-stabilized cream cheeses had higher hardness values than the cream cheeses manufactured with the individual stabilizers. Differences were observed between the sensory attributes of cream cheeses stabilized with CBN and those made with individual stabilizers. At low temperatures, the higher hardness and G' values of CBN-stabilized cream cheeses could be due to synergistic interaction between XG and galactomannans. The higher elasticity of XG-stabilized cream cheeses at high temperatures could be due to its higher thermal stability. This study showed that the stabilizers added during manufacture of cream cheese affected its texture, rheological, and sensory properties., (Copyright © 2020 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Control of acidity is critical for cheese quality, as high acidity can be associated with poor flavor and textural attributes. We investigated an alternative method to control cheese acidity, specifically in low-fat (LF) and reduced-fat (RF) milled curd, direct-salted Gouda cheese, which involved altering the initial lactose content of cheesemilk. In traditional Gouda cheese manufacture, a critical technique to control acidity is whey dilution (WD); that is, partial removal of whey and its replacement with water. Direct standardization of the lactose content of milk during the ultrafiltration process could be a simpler and more effective technique to control cheese acidity. This study compared the effect of traditional WD at 2 different levels, 15 and 30% (WD15 and WD30), with the alternative approach of adjustment of the lactose content of milk using low-concentration-factor ultrafiltration (LCF-UF). The composition, texture, functionality, and sensory properties of these LF and RF Gouda cheeses were evaluated. A milled curd, direct-salted cheese manufacturing protocol was used. Milks used for cheesemaking had a lactose-to-casein (L:CN) ratio of approximately 1.8, which is the typical ratio found in milk, whereas milks prepared with lactose standardization (LS) were made from UF concentrated milks with water added during filtration to achieve a L:CN ratio of approximately 1.1. Cheeses made with LS exhibited lower lactose and lactic acid contents than WD30 and WD15, leading to significantly higher pH values in the cheese. Dynamic small-amplitude oscillatory rheology indicated that use of LS led to cheeses with a lower crossover temperature (melting point) than the cheeses made with WD. Cheeses made with LS had lower insoluble Ca contents, likely caused by the addition of water required to achieve the lower L:CN ratio in these milks. Sensory analysis also indicated that LS cheeses had lower acidity and softer texture. These results suggest that standardization of the L:CN ratio of milk could be a useful alternative to WD (or a curd rinse step) to reduce acidity in cheeses. In addition, LS could be used to help soften texture and increase meltability, if desired in lower-fat cheese types., (Copyright © 2020 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Food protein allergies are a major global concern. Hydrolysis of food proteins reduces their allergenicity, but another novel approach is the covalent attachment of polysaccharides to proteins via the Maillard reaction (i.e., glycation), which blocks some IgE binding epitopes on the protein allergen. We wanted to examine whether enzymatic hydrolysis, combined with glycation, could further reduce IgE binding for people with a cow milk protein allergy. Whey protein isolate (WPI) was hydrolyzed by immobilized trypsin and chymotrypsin to degree of hydrolysis (DH) values of 17 to 27%. Immobilized enzymes were used to avoid heat-treating the hydrolysate (to inactivate the enzymes, because heating could also affect the IgE binding ability of the protein). The resultant whey protein isolate hydrolysates (WPIH) were then glycated with 10-kDa dextran (DX) in aqueous solutions held at 62°C for 24 h. We analyzed the molar mass (M W ) of WPIH samples and their corresponding glycates (WPIH-DX) using size-exclusion chromatography with multi-angle laser light scattering. We obtained blood sera from 8 patients who had been diagnosed with a cow milk protein allergy, and we used a composite serum for IgE binding analysis. The average M W values of samples WPIH-1 to WPIH-3 decreased from 11.15, 9.46, and 7.57 kDa with increasing DH values of 18.7, 22.5, and 27.1%. Glycation significantly reduced the high bitterness of the WPIH samples, as assessed by a trained sensory panel. The WPIH-DX glycates had significantly reduced WPI-specific IgE binding capacity compared to WPI or unglycated WPIH; we found an almost 99% reduction in IgE binding for the WPIH-DX glycate made from WPIH with a DH value of 27.1%. Hydrolysis of WPI followed by glycation with DX via the Maillard reaction significantly decreased the allergenicity of whey proteins., (Copyright © 2020 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Monomeric bovine β-casein self-associates into micelles under appropriate conditions of protein concentration, serum composition and temperature. The present study investigated self-association characteristics of a β-casein concentrate (BCC) prepared from milk at pilot-scale using membrane filtration. The BCC had a casein:whey protein ratio of 77:23, with ∼95% of casein consisting of β-casein, and the remainder being mostly κ-CN. BCC was reconstituted to 1.2% protein (a typical level in infant formula) in various liquid media at pH 6.8 and incubated at different temperatures from 4 to 63 °C for 30 min. Self-association of β-casein on heating was thermo-reversible in deionised water, lactose (4, 6 or 8%) or calcium (9 mM) solutions. In most serum phases, BCC became highly opaque after incubation at 63 °C, but clarified rapidly during cooling to 25 °C. However, in simulated milk ultrafiltrate (SMUF), which has a high ionic strength and is supersaturated in calcium phosphate (CaP), BCC remained opaque during cooling to 25 °C, and retained residual turbidity after 15 h of holding at 4 °C; if SMUF was prepared without phosphate then turbidity development in BCC solutions was markedly reduced. The complexes responsible for this turbidity development were successfully dissociated with 50 mM trisodium citrate. Analysis of pH during heating and holding at 60 °C indicated that SMUF acidified continuously under the period of study, while acidification in BCC/SMUF mixtures terminated after a short period, indicating that the type of CaP formed on heating is altered in the presence of BCC. This study demonstrates that BCC ingredients exhibit pronounced temperature-dependant changes in colloidal properties that are strongly affected by the presence of minerals commonly found in nutritional product formulations., (Copyright © 2018 Elsevier B.V. All rights reserved.)

In recent years, a large increase in the production of milk protein concentrates (MPC) has occurred. However, compared with other types of milk powders, few studies exist on the effect of key processing parameters on powder properties. In particular, it is important to understand if key processing parameters contribute to the poor solubility observed during storage of high-protein MPC powders. Ultrafiltration (UF) and diafiltration (DF) are processing steps needed to reduce the lactose content of concentrates in the preparation of MPC with a protein content of 80% (MPC80). Evaporation is sometimes used to increase the TS content of concentrates before spray drying, and some indications exist that inclusion of this processing step may affect protein properties. In this study, MPC80 powders were manufactured by 2 types of concentration methods: membrane filtration with and without the inclusion of an evaporation step. Different concentration methods could affect the mineral content of MPC powders, as soluble salts can permeate the UF membrane, whereas no mineral loss occurs during evaporation, although a shift in calcium equilibrium toward insoluble forms may occur at high protein concentration levels. It is more desirable from an energy efficiency perspective to use higher total solids in concentrates before drying, but concerns exist about whether a higher protein content would negatively affect powder functionality. Thus, MPC80 powders were also manufactured from concentrates that had 3 different final protein concentrations (19, 21, and 23%; made from 1 UF retentate using batch recirculation evaporation, a similar concentration method). After manufacture, powders were stored for 6 mo at 30°C to help understand changes in MPC80 properties that might occur during shelf-life. Solubility and foaming properties were determined at various time points during high-temperature powder storage. Inclusion of an evaporation step, as a concentration method, resulted in MPC80 that had higher ash, total calcium, and bound calcium (of rehydrated powder) contents compared to concentration with only membrane filtration. Concentration method did not significantly affect the bulk (tapped) density, solubility, or foaming properties of the MPC powders. Powder produced from concentrate with 23% protein content exhibited a higher bulk density and powder particle size than powder produced from concentrate that had 19% protein. The solubility of MPC80 powder was not influenced by the protein content of the concentrate. The solubility of all powders significantly decreased during storage at 30°C. Higher protein concentrations in concentrates resulted in rehydrated powders that had higher viscosities (even when tested at a constant protein concentration). The protein content of the concentrate did not significantly affect foaming properties. Significant changes in the mineral content are used commercially to improve MPC80 solubility. However, although the concentration method did produce a small change in the total calcium content of experimental MPC80 samples, this modification was not sufficiently large enough (<7%) to influence powder solubility., (Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Manufacture of cream cheese involves the formation of an initial acid-induced gel made from high-fat milk, followed by a series of processing steps including shearing, heating, and dewatering that complete the conversion of the acid gel into a complex cheese product. We investigated 2 critical parameters for their effect on the initial gel: homogenization pressure (HP) of the high-fat cheese milk, and fermentation temperature (FT). The impact of a low (10 MPa) and high (25 MPa) HP, and low (20°C) and high (26°C) FT were investigated for their effects on rheological and textural properties of acid-induced gels. Intact acid gels were sheared and heated to 80°C, and then their rheological properties were analyzed to help understand the effect of shearing/heating processes on the gel characteristics. The effect of HP on fat globule size distribution and the amount of protein not involved in emulsion droplets (i.e., in the bulk phase) were also studied. For cream cheese trials, a central composite experimental design was used to explore the effect of these 2 parameters (HP and FT) on the texture, rheology, and sensory properties of experimentally manufactured cream cheese. Storage modulus (G') and hardness values of cream cheeses were obtained from small amplitude oscillatory rheology tests and texture profile analysis, respectively. Quantitative spectrum descriptive sensory analysis was also performed. Consistency of acid gels (measured using a penetration test) increased with an increase in FT and with an increase in HP. Although stiffer acid-induced gels were formed at high FT, after the heating and shearing processes the apparent viscosity of the samples formed at high FT was lower than those formed at low FT. For the cream cheeses, significant prediction models were obtained for several rheological and textural attributes. The G' values at 8°C, instrumental hardness, and sensory firmness attributes were significantly correlated (r > 0.84); all these attributes significantly decreased with an increase in FT, and HP was not a significant parameter in the prediction models developed for these attributes. Significant interactions were observed between the HP and FT terms for these prediction models. Higher HP increased the amount of protein adsorbed at interface of fat globules but decreased bulk phase protein content (which may be important for crosslinking this gelled emulsion system). At higher FT temperature, coarser gel networks were likely formed. The combined effect of a coarser acid gel network at high FT, and less bulk phase casein available for crosslinking the acidified emulsion gel with an increase in HP, could have contributed to the lower stiffness/firmness observed in cream cheese made under conditions of both high FT and high HP. Stickiness of cream cheese greatly increased under conditions of high FT and high HP, whereas the sensory attributes cohesiveness of mass and difficulty to dissolve decreased. This study helped to better understand the complex relationships between the initial acid-induced gel phase and properties of the (final) cream cheese., (Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

A growing concern around the world is the number of people who are suffering from food protein allergies. One potential approach to decrease protein allergenicity is to block IgE-binding epitopes of the protein allergen by attachment of polysaccharides via the Maillard reaction (i.e., glycation). Protein glycation has been extensively studied to modify various functional properties. We wanted to examine whether glycates could reduce IgE binding in patients with cow milk protein allergy and to explore how the size (molar mass; M W ) of the polysaccharide affects this IgE-binding capacity. Glycation was performed using the initial step of the Maillard reaction performed in aqueous solutions. The specific goal of this study was to reduce the IgE-binding capacity of whey protein isolate (WPI) through glycation with dextran (DX). Blood sera were obtained from 8 patients who had been diagnosed with cow milk protein allergy, and a composite sera sample was used for IgE-binding analysis by the ImmunoCap (Phadia, Uppsala, Sweden) method. The WPI was glycated with DX of M W ranging from 1 to 2,000 kDa, and the M W of purified glycates was determined using size-exclusion chromatography coupled with multiangle laser light scattering. The WPI to DX molar ratios in the glycates made from DX that had M W values of 1, 3.5, 10 (G10), 150, 500, and 2,000 kDa were 1:4, 1:3, 1:2, 1:1.5, 1:1, and 1:1, respectively. With the increase in the M W of DX, there was an increase in the M W values of the corresponding glycates but a decrease in the number of bound DX. The WPI-DX glycates had lower whey protein IgE-binding capacity than native WPI, with the lowest IgE-binding capacity obtained in the G10 glycate. The DX binding ratios and morphology results from atomic force microscopy images suggested that glycation of WPI with small-M W DX resulted in extensive protein surface coverage, probably due to the attachment of up to 4 DX molecules per whey protein. The lower IgE binding of the G10 glycate was likely due to greater steric hindrance (or a physical barrier) at the surface of the protein. In summary, our results demonstrate that glycating WPI with DX via Maillard reaction can potentially be used to decrease the allergenicity of whey protein., (Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

We proposed that the performance and sensory properties of reduced-Na, low-moisture, part-skim (LMPS) Mozzarella cheese could be extended by the application of high hydrostatic pressure (HHP) to cheese postmanufacture and thereby decrease microbial and enzymatic activity. Fermentation-produced camel chymosin was also used as a coagulant to help reduce proteolysis during storage. Average composition of the LMPS Mozzarella cheeses was 48.6 ± 0.6% moisture, 22.5 ± 0.4% fat, 24.5 ± 0.6% protein, and 1.0 ± 0.1% NaCl. Blocks of cheeses were divided into 3 groups randomly after manufacture and stored at approximately 4°C for 20 wk. The control group was not HHP treated. Two weeks after manufacture, 2 groups of cheese samples were treated with HHP at 500 or 600 MPa for 3 min and then returned to storage at approximately 4°C. Analysis was performed during 20 wk of storage after cheese manufacture. Texture profile analysis (TPA) and dynamic low-amplitude oscillatory rheology were used to monitor cheese functionality. Quantitative descriptive analysis was conducted with 9 trained panelists using a 15-point scale to evaluate texture and flavor attributes of unmelted cheese as well as cheeses melted on pizzas. Pressure treatments at 500 and 600 MPa resulted in approximately 1 and 2 log reduction in the numbers of starter culture, respectively, compared with the control when measured 1 d after HHP treatment. Starter numbers continued to decrease in all cheeses over the 20 wk of storage, but the decrease was larger in the HHP-treated cheeses. Even though the initial numbers of nonstarter lactic acid bacteria were the same in all cheeses, the numbers of these bacteria increased faster in the control cheeses. High-pressure treatment of LMPS Mozzarella cheese resulted in an initial (1 d after HHP treatment) increase in pH, but by 2 wk after HHP treatment there was no statistical difference in pH values between control and HHP-treated samples. Immediately after treatment, HHP-treated cheeses exhibited significantly lower TPA and sensory (unmelted) hardness. However, by 14 wk after pressure treatment, the 600-MPa HHP-treated cheese had significantly higher TPA compared with control or 500-MPa HHP-treated cheeses. Sensory panels also indicated that by 14 wk after HHP treatment, the 600-MPa treated samples were significantly firmer than the control or 500-MPa treated cheeses. Compared with control cheese, cheeses treated at 600 or 500 MPa exhibited lower water-soluble nitrogen values at 6 and 10 wk after pressure treatment, respectively. By 10 wk after pressure treatment, the levels of intact α S1 -casein were significantly higher in all HHP-treated cheeses compared with the control. Pizza sensory panels indicated that 600-MPa treated cheese was significantly chewier and exhibited lower blister quantity and higher strand thickness compared with control cheeses. High hydrostatic pressure treatment of low-Na, LMPS Mozzarella cheese could result in the extension of its desired baking characteristics when the cheese is stored at refrigerated temperature., (Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

We investigated the effect of fermenting milk with 2 strains (DGCC7785 and St-143) of Streptococcus thermophilus, which are known to produce different types of exopolysaccharide (EPS) structures. The yields and physical properties of these ropy EPS were monitored during the fermentation of milk at different temperatures. We wanted to understand how these types of EPS properties affected yogurt gelation. Reconstituted skim milk was fermented at 33, 39, or 45°C until pH values reached 5.2, 4.9, 4.7, and 4.5. Molar mass of ropy EPS samples was determined using size exclusion chromatography coupled with multiangle laser light scattering. Rheological properties of fermented milk gels were analyzed using small-strain dynamic oscillatory measurements. In both strains, concentrations of ropy EPS increased during fermentation and at all temperatures. Fermentation times, by both strains, were shortest at 45°C and longest at 33°C. For both strains, molar mass of ropy EPS ranged from 2 to 4 × 10 6 g/mol during fermentation. A major proteinaceous contaminant that was co-isolated with the ropy EPS fraction by our isolation method was identified as a milk-derived phosphoglycoprotein PP3. Increase in fermentation temperature from 33 to 45°C significantly decreased the storage modulus values (from 170 to 41 Pa) for milk gelled by strain DGCC7785, whereas the gels made with St-143 had very low storage modulus values (11-17 Pa) regardless of fermentation temperatures. For both strains, the values of maximum loss tangent in the milk gels increased with fermentation temperature; the maximum loss tangent occurred at higher pH values when milk was fermented by strain DGCC7785. The specific type of EPS produced appeared to be responsible for the differences in yogurt texture rather than the concentration or molar mass of the EPS., (Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Understanding the chemistry of milk and its components is critical to the production of consistent, high-quality dairy products as well as the development of new dairy ingredients. Over the past 100 yr we have gone from believing that milk has only 3 protein fractions to identifying all the major and minor types of milk proteins as well as discovering that they have genetic variants. The structure and physical properties of most of the milk proteins have been extensively studied. The structure of the casein micelle has been the subject of many studies, and the initial views on submicelles have given way to the current model of the micelle as being assembled as a result of the concerted action of several types of interactions (including hydrophobic and the formation of calcium phosphate nanoclusters). The benefits of this improved knowledge of the type and nature of casein interactions include better control of the cheesemaking process, more functional milk powders, development of new products such as cream liqueurs, and expanded food applications. Increasing knowledge of proteins and minerals was paralleled by developments in the analysis of milk fat and its synthesis together with greater knowledge of its packaging in the milk fat globule membrane. Advances in analytical techniques have been essential to the isolation and characterization of milk components. Milk testing has progressed from gross compositional analyses of the fat and total solids content to the rapid analysis of milk for a wide range of components for various purposes, such as diagnostic issues related to animal health. Up to the 1950s, research on dairy chemistry was mostly focused on topics such as protein fractionation, heat stability, acid-base buffering, freezing point, and the nature of the calcium phosphate present in milk. Between the 1950s and 1970s, there was a major focus on identifying all the main protein types, their sequences, variants, association behavior, and other physical properties. During the 1970s and 1980s, one of the major emphases in dairy research was on protein functionality and fractionation processes. The negative cloud over dairy fat has lifted recently due to multiple reviews and meta-analyses showing no association with chronic issues such as cardiovascular disease, but changing consumer misconceptions will take time. More recently, there has been a great deal of interest in the biological and nutritional components in milk and how these materials were uniquely designed by the cow to achieve this type of purpose., (Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Covalent attachment of polysaccharides to proteins (conjugation) via the Maillard reaction has been extensively studied. Conjugation can lead to a significant improvement in protein functionality (e.g., solubility, emulsification, and heat stability). Caseins have previously been successfully conjugated with maltodextrin (Md), but the effect on the detailed acid gelation properties has not been examined. We studied the effect of conjugating sodium caseinate (NaCN) with 3 different sized Md samples via the Maillard reaction in aqueous solutions. The Md samples had dextrose equivalents of 4 to 7, 9 to 12, and 20 to 23 for Md40, Md100, and Md200, respectively. The conjugation reaction was performed in mixtures with 5% NaCN and 5% Md, which were heated at 90°C for 10 h. The degree of conjugation was estimated from the reduction in free amino groups as well as color changes. Sodium dodecyl sulfate-PAGE analysis was performed to confirm conjugation by employing staining of both protein and carbohydrate bands. The molar mass of samples was determined by size-exclusion chromatography coupled with multi-angle laser light scattering. After the conjugation reaction, samples were then gelled by the addition of 0.63% (wt/vol) glucono-δ-lactone at 30°C, such that samples reached pH 4.6 after about 13 h. The rheological properties of samples during acidification was monitored by small-strain dynamic oscillatory rheology. The microstructure of acid gels at pH 4.6 was examined by fluorescence microscopy. Conjugation resulted in a loss of 10.8, 8.8, and 11.9% of the available amino groups in the protein for the NaCN-Md40 conjugates (C40), NaCN-Md100 conjugates (C100), and NaCN-Md100 conjugates (C200), respectively. With a decrease in the size of the type of Md, an increase occurred in the molar mass of the resultant conjugate. The weight average molar masses of NaCN-Md samples were 340, 368, and 425 kDa for the conjugates C40, C100, and C200, respectively. Addition of Md to NaCN dispersion resulted in slightly shorter acid gelation times even without the conjugation reaction. The storage modulus (G') of acid gels was significantly lower in conjugated samples compared with the corresponding (unreacted) mixtures of Md and NaCN. The sample with the lowest G' value at pH 4.6 was the C40 conjugate. Fluorescence microscopy showed that gels made by conjugates had slightly larger pores. These results indicate that conjugation of casein modified its acid gelation properties, presumably by the Md polysaccharide moiety hindering aggregation and rearrangements of the casein network., (Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

The yield and chemical structures of exopolysaccharides (EPS) produced by many strains of Streptococcus thermophilus have been characterized. However, the kinetics (or production profile) for EPS during milk fermentation is not clear. In this study, we investigated whether any differences existed in the yield and molar mass of EPS when milk was fermented at the same acidification rate by 2 strains of S. thermophilus (St-143 and ST-10255y). The type of EPS produced by these 2 strains is different. Milk samples were analyzed for EPS concentration every 30 min during a fermentation period of 270 min (final pH 4.5) by using a modified quantification method, which was faster and validated for its recovery of added EPS. Rheological properties of milks during fermentation were also analyzed using small-strain dynamic oscillatory rheology. For the determination of molar mass, EPS extracts were isolated by ultrafiltration of whey obtained during fermentation of milk to pH values 5.2, 4.9, 4.7, and 4.5, and molar mass was analyzed using size-exclusion chromatography-multi-angle laser light scattering. During fermentation, both strains appeared to start producing significant amounts of EPS after about ∼150 min, which corresponded to pH ∼5.3, which was close to the point of gelation. During the remainder of the fermentation process (150-270 min), the EPS concentration from strains St-143 and ST-10255y significantly increased from 30 to 72 mg/L and from 26 to 56 mg/L, respectively. The quantity of EPS recovered by our modified method was estimated to represent ∼60% of the total EPS added to milk. The molar mass of EPS produced by both strains appeared to slightly decrease during fermentation. At pH 5.2, EPS from St-143 and ST-10255y had molar masses of 2.9 × 10 6 and 1.4 × 10 6 g/mol, respectively, which decreased to 1.6 × 10 6 and 0.8 × 10 6 g/mol, respectively, when the pH of milk was 4.5. Distinct differences were apparent in the rheological properties of gels fermented by the 2 strains. At the end of fermentation, St-143 fermented milk had weaker gels with storage modulus (G') value at pH 4.6 of 26 Pa, whereas gels made with ST-10255y were stiffer with a G' value at pH 4.6 of 82 Pa. For St-143 gels, maximum loss tangent (LT max ) values were higher (0.50) and occurred earlier (at a higher pH value) than the LT max values (0.46) for gels from ST-10255y strain. Because the fermentation conditions were identical for both strains, the observed changes in rheological properties could be due to the differences in chemical structures and molar mass of the EPS produced by these 2 S. thermophilus strains., (Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Exopolysaccharides (EPS) produced by some lactic acid bacteria are often used by the dairy industry to improve the rheological and physical properties of yogurt, but the relationship between their structure and functional effect is still unclear. The EPS from different species, or different strains from the same species, may differ in terms of molar mass, repeating unit structure, and EPS yield during fermentation of milk. This study aimed to characterize the detailed properties of EPS produced from 7 strains of Streptococcus thermophilus, which is one of the key cultures used for yogurt manufacture. Milk was fermented with strains DGCC 7698, DGCC 7710, DGCC 7785, ST-10255y, St-143, STCth-9204, and ST4239. These strains were selected because they have been used in previous studies on yogurt texture, but a complete description of their EPS structural properties has not yet been reported. All strains were fermented under a similar acidification rate by adjusting the level of supplementation with peptone or the inoculation level, which allowed for a comparison of EPS yields under similar growth conditions (reconstituted skim milk at 40°C). The EPS from each strain was isolated and the weight-average molar mass and z-average root mean square radius determined using size-exclusion chromatography multiangle laser light scattering. The monosaccharide composition of EPS was determined using gas chromatography-mass spectrometry, and repeating unit structure was determined using nuclear magnetic resonance spectroscopy. The weight-average molar mass values of EPS ranged from 0.14 to 1.61 × 10 6 g/mol. All 7 EPS samples were uncharged. The strains ST-10255y and ST4239 had EPS with the same repeating unit structure. The monosaccharide compositions of the various EPS were mainly composed of glucose and galactose, with low levels of rhamnose in the EPS isolated from DGCC 7698, and N-acetylgalactosamine in the EPS from DGCC 7785, ST-10255y, and ST4239. The yields of EPS (measured when fermented milks reached pH 4.6) ranged from 8.0 to 76.4 mg of glucose equivalents/kg. In addition to (free) EPS, some strains were also able to produce capsular polysaccharide (associated with the bacterial cells) when observed with negative staining technique. The results of our study will help the dairy industry to better understand the mechanism by which different strains of Streptococcus thermophilus affect yogurt texture., (Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

The texture, functionality, and quality of Mozzarella cheese are affected by critical parameters such as pH and the rate of acidification. Acidification is typically controlled by the selection of starter culture and temperature used during cheesemaking, as well as techniques such as curd washing or whey dilution, to reduce the residual curd lactose content and decrease the potential for developed acidity. In this study, we explored an alternative approach: adjusting the initial lactose concentration in the milk before cheesemaking. We adjusted the concentration of substrate available to form lactic acid. We added water to decrease the lactose content of the milk, but this also decreased the protein content, so we used ultrafiltration to help maintain a constant protein concentration. We used 3 milks with different lactose-to-casein ratios: one at a high level, 1.8 (HLC, the normal level in milk); one at a medium level, 1.3 (MLC); and one at a low level, 1.0 (LLC). All milks had similar total casein (2.5%) and fat (2.5%) content. We investigated the composition, texture, and functional and sensory properties of low-moisture, part-skim Mozzarella manufactured from these milks when the cheeses were ripened at 4°C for 84d. All cheeses had similar pH values at draining and salting, resulting in cheeses with similar total calcium contents. Cheeses made with LLC milk had higher pH values than the other cheeses throughout ripening. Cheeses had similar moisture contents. The LLC and MLC cheeses had lower levels of lactose, galactose, lactic acid, and insoluble calcium compared with HLC cheese. The lactose-to-casein ratio had no effect on the levels of proteolysis. The LLC and MLC cheeses were harder than the HLC cheese during ripening. Maximum loss tangent (LT), an index of cheese meltability, was lower for the LLC cheese until 28d of ripening, but after 28d, all treatments exhibited similar maximum LT values. The temperature where LT=1 (crossover temperature), an index of softening point during heating, was higher for MLC and LLC cheese at 56 and 84d of ripening. The LLC cheese also had lower blister color and less stretch than MLC and HLC cheese. Adjusting the lactose content of milk while maintaining a constant casein level was a useful technique for controlling cheese pH, which affected the texture, functionality, and sensory properties of low-moisture, part-skim Mozzarella cheese., (Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

We and others have shown previously that fisetin, a plant flavonoid, has therapeutic potential against many cancer types. Here, we examined the probable mechanism of its action in prostate cancer (PCa) using a global metabolomics approach. HPLC-ESI-MS analysis of tumor xenografts from fisetin-treated animals identified several metabolic targets with hyaluronan (HA) as the most affected. Efficacy of fisetin on HA was then evaluated in vitro and also in vivo in the transgenic TRAMP mouse model of PCa. Size exclusion chromatography-multiangle laser light scattering (SEC-MALS) was performed to analyze the molar mass (Mw) distribution of HA. Fisetin treatment downregulated intracellular and secreted HA levels both in vitro and in vivo Fisetin inhibited HA synthesis and degradation enzymes, which led to cessation of HA synthesis and also repressed the degradation of the available high-molecular-mass (HMM)-HA. SEC-MALS analysis of intact HA fragment size revealed that cells and animals have more abundance of HMM-HA and less of low-molecular-mass (LMM)-HA upon fisetin treatment. Elevated HA levels have been shown to be associated with disease progression in certain cancer types. Biological responses triggered by HA mainly depend on the HA polymer length where HMM-HA represses mitogenic signaling and has anti-inflammatory properties whereas LMM-HA promotes proliferation and inflammation. Similarly, Mw analysis of secreted HA fragment size revealed less HMM-HA is secreted that allowed more HMM-HA to be retained within the cells and tissues. Our findings establish that fisetin is an effective, non-toxic, potent HA synthesis inhibitor, which increases abundance of antiangiogenic HMM-HA and could be used for the management of PCa., (© The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.)

Tetrasodium pyrophosphate (TSPP) is widely used as an emulsifying salt (ES) in process cheese. Previous reports have indicated that TSPP exhibits some unusual properties, including the gelation of milk proteins at specific ES concentrations. We studied the effect of various concentrations (0.25-2.75%) of TSPP and cooking times (0-20min) on the rheological, textural, and physical properties of pasteurized process Cheddar cheese using a central composite rotatable experimental design. Cheeses were made with a constant pH value to avoid pH as a confounding factor. Modeling of the textural properties of process cheese made with TSPP exhibited complex behavior, with polynomial models (cubic) giving better predictions (higher coefficient of determination values) than simpler quadratic models. Meltability indices (degree of flow from the UW MeltProfiler (University of Wisconsin-Madison), loss tangent value at 60°C from rheological testing, and Schreiber melt area) initially decreased with increasing TSPP concentrations, but above a critical ES concentration (~1.0%) meltability increased at higher TSPP concentrations. The storage modulus values measured at 70°C for process cheese initially increased with increasing TSPP concentration, but above a concentration of 1% ES, the storage modulus values decreased. Cooking time had little effect on the various melting or rheological properties. With an increase in TSPP concentration, the insoluble Ca and P contents increased, suggesting that TSPP addition resulted in the formation of insoluble calcium pyrophosphate complexes; some of which were likely associated with caseins. A portion of the added TSPP remained in the soluble phase. The acid-base buffering profiles also indicated that calcium pyrophosphate complexes were formed in cheese made with TSPP. In milk systems, low levels of TSPP have been shown to induce protein crosslinking and gelation, whereas at higher TSPP concentrations milk gelation was inhibited due to excessive charge repulsion from these calcium pyrophosphate complexes. We hypothesized that a similar phenomenon was occurring in our process cheese, resulting in the initial reduction in meltability with TSPP addition due to protein crosslinking, but at higher TSPP levels meltability increased due to excessive charge repulsion., (Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Bioactive peptides, including angiotensin-I-converting enzyme-inhibitory (ACEI) peptides, were investigated in commercially produced Wisconsin Cheddar cheeses that ranged in age from ≤ 6d to more than 2 yr. The ACEI activity of cheese was determined in water-soluble extracts (WSE) that were fractionated for components with molecular weight (MW) ≤ 3,000 Da, and peptides identified using HPLC and tandem mass spectrometry. The number of types of bioactive peptides increased with an increase in ripening time. Six of the identified ACEI peptides, Ile-Pro-Pro (IPP), Val-Pro-Pro (VPP), Glu-Lys-Asp-Glu-Arg-Phe (EKDERF), Val-Arg-Tyr-Leu (VRYL), Tyr-Pro-Phe-Pro-Gly-Pro-Ile-Pro-Asn (YPFPGPIPN), and Phe-Phe-Val-Ala-Pro (FFVAP), with known high ACEI activity (low IC50 values, the concentration needed to inhibit ACE to 50% of its original activity) were synthesized and used to quantify the amounts of these peptides in various cheese extracts. The concentrations of these 6 ACEI peptides increased up to a certain stage of ripening. The maximum contents of IPP, VPP, and EKDERF were 2.8, 7.4, and 5.3mg/100 g of cheese, respectively, and these levels were found in a 1-yr-old Cheddar cheese sample. The maximum content of VRYL (7.5mg/100 g of cheese) was found in a 2-yr-old Cheddar cheese sample, whereas the maximum content of YPFPGPIPN (6.8 mg/100 g of cheese) was found in a 6-mo-old Cheddar cheese sample. Trace amounts of FFVAP were found in these cheeses. Aged Cheddar cheese was found to be a rich source of ACEI peptides even though large differences exist between cheeses from different manufacturers., (Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Milk for yogurt manufacture is subjected to high heat treatment to denature whey proteins. Low milk pH values (≤ 6.5) at heating result in most denatured whey proteins becoming associated with casein micelles, whereas high milk pH values (≥ 7.0) at heating result in the formation of mostly soluble (nonmicellar) denatured whey protein complexes. There are conflicting reports on the relative importance of soluble and casein-bound whey protein aggregates on the properties of acid gels. Prior studies investigating the effect of pH of milk at heating used model gels in which milk was acidified by glucono-δ-lactone; in this study, we prepared yogurt gels using commercial starter cultures. Model acid gels can have very different texture and physical properties from those made by fermentation with starter cultures. In this study, we investigated the effects of different pH values of milk at heating on the rheological, light backscatter, and microstructural properties of yogurt gels. Reconstituted skim milk was adjusted to pH values 6.2, 6.7, and 7.2 and heated at 85°C for 30 min. A portion of the heated milk samples was readjusted back to pH 6.7 after heating. Milks were inoculated with 3% (wt/wt) yogurt starter culture and incubated at 40°C until pH 4.6. Gel formation was monitored using dynamic oscillatory rheology, and parameters measured included the storage modulus (G') and loss tangent (LT) values. Light-backscattering properties, such as the backscatter ratio (R) and the first derivative of light backscatter ratio (R'), were also monitored during fermentation. Fluorescence microscopy was used to observe gel microstructure. The G' values at pH 4.6 were highest in gels made from milk heated at pH 6.7 and lowest in milk heated at pH 6.2, with or without pH adjustment after heating. The G' values at pH 4.6 were lower in samples after adjustment back to pH 6.7 after heating. No maximum in the LT parameter was observed during gelation for yogurts made from milk heated at pH 6.2; a maximum in LT was observed at pH ~4.8 for samples heated at pH 6.7 or 7.2, with or without pH adjustment after heating. Higher R-values were observed with an increase in pH of heating, with or without pH adjustment after heating. The sample heated at pH 6.2 had only one major peak in its R' profile during acidification, whereas samples heated at pH 6.7 and 7.2 had 2 large peaks. The lack of a maximum in LT parameter and the presence of a single peak in the R' profile for the samples heated at pH 6.2 were likely due to the partial solubilization of insoluble calcium phosphate when milk was acidified to this lower pH value. No clear differences were observed in the microstructures of gels between the different treatments. This study indicates that heating milk at the natural pH (~6.7) created an optimum balance of casein-bound and soluble denatured whey proteins, which resulted in yogurt with the highest gel stiffness., (Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Low-sodium cheeses often exhibit an acidic flavor due to excessive acid production during the manufacturing and the initial stage of ripening, which is caused by ongoing starter culture activity facilitated by the low salt-in-moisture levels. We proposed that this excessive starter-induced acidity could be prevented by the fortification of cheese milk with ultrafiltration (UF) retentates (to increase curd buffering), and by decreasing microbial activity using the application of high-hydrostatic pressure (HHP) treatment (that is, to reduce residual starter numbers). Camel chymosin was also used as a coagulant to help reduce bitterness development (a common defect in low-sodium cheeses). Three types of low-Na (0.8% NaCl) Cheddar cheeses were manufactured: non-UF fortified, no HHP applied (L-Na); UF-fortified (cheese milk total solids = 17.2 ± 0.6%), no HHP applied (L-Na-UF); and UF-fortified, HHP-treated (L-Na-UF-HHP; 500 MPa for 3 min applied at 1 d post-cheese manufacture). Regular salt (2% NaCl) non-UF fortified, non-HHP treated (R-Na) cheese was also manufactured for comparison purposes. Analysis was performed at 4 d, 2 wk, and 1, 3, and 6 mo after cheese manufacture. Cheese functionality during ripening was assessed using texture profile analysis and dynamic low-amplitude oscillatory rheology. Sensory Spectrum and quantitative descriptive analysis was conducted with 9 trained panelists to evaluate texture and flavor attributes using a 15-point scale. At 4 d and 2 wk of ripening, L-Na-UF-HHP cheese had ~2 and ~4.5 log lower starter culture numbers, respectively, than all other cheeses. Retentate fortification of cheese milk and HHP treatment resulted in low-Na cheeses having similar insoluble calcium concentrations and pH values compared with R-Na cheese during ripening. The L-Na-UF cheese exhibited significantly higher hardness values (measured by texture profile analysis) compared with L-Na cheese until 1 mo of ripening; however, after 1 mo, all low-Na cheeses exhibited similar hardness values, which were significantly lower than R-Na cheese. Pressure treatment significantly increased maximum loss tangent (meltability) from rheology testing and decreased melt temperature. Sensory results indicated only very slight bitterness (<2.5 out of 15-point scale) was detected in all cheeses during the 6 mo of ripening. The L-Na-UF-HHP cheese did not significantly differ in bitterness and acidity from R-Na cheese during ripening. Pressures treatment of cheese at 500 MPa and cheese milk retentate fortification could be used to improve the quality of low-Na cheese., (Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

The rennet coagulation of milk has been extensively studied. Mathematical modeling of the gelation process has been performed, mainly for the purpose of predicting the gel point. Rheological profiles of rennet gels during aging (long reaction times) have indicated that the gel stiffness (modulus) attains a maximum and thereafter decreases. We wanted to model this type of behavior and used the Carlson model, which includes terms for the proteolysis of κ-casein hairs (creating active sites) and the crosslinking of these activated sites. To account for the observed decrease in the gel modulus with time, we modified the Carlson model by adding an exponential decay term, which we ascribe to endogenous syneresis. We believe that this decay (i.e., syneresis rate) would likely be influenced by the mobility of bonds within casein micelles (in gels as indicated by the rheological loss tangent parameter). To modify the internal structural bonding of casein micelles, reconstituted skim milk was acidified to pH values 6.4, 6.0, 5.8, 5.6, and 5.4, or EDTA was added to milk at concentrations of 0, 2, 4, and 6mM, and the final pH values of EDTA-treated samples were subsequently adjusted to pH 6.0. These treatments were then used to prepare rennet gel samples that were monitored by dynamic low amplitude oscillatory rheometry. When the modified Carlson model was fitted to the actual experimental storage modulus values of each sample, it fitted the data reasonably well (especially the pH trial data). As the pH values of milk decreased, the modulus values at infinite reaction time (G'∞) increased; however, G'∞ decreased with an increase in the EDTA concentration. In the pH trial, the rate constants for the proteolysis of κ-casein hairs and the crosslinking of these activated sites exhibited a maximum at pH 5.6 and 6.0, respectively. The rate constant for endogenous syneresis increased at pH values <6.0. The rate constant for endogenous syneresis was significantly positively correlated (r≥0.96) with the loss tangent values of gels (indicating greater mobility), probably due to the loss of insoluble calcium phosphate crosslinking within micelles, which was significantly negatively correlated (r≥0.81) with the rate constant for endogenous syneresis. In the EDTA trial, with an increase in the EDTA concentration no maximum was observed in the rate constants related to proteolysis of κ-casein hairs or crosslinking of these activated sites. The rate constant for endogenous syneresis decreased at higher EDTA levels. The different rheological/modeling behavior in the EDTA trials was likely due to the very significant inhibition of rennet gelation induced by the use of EDTA, which also resulted in extremely long reaction times. Our modified Carlson model fit our experimental pH trial data very well, which indicates that the rennet gel system has the potential to synerese from the start; indeed this ability is an innate property of the casein micelle. Endogenous syneresis was enhanced by the loss of insoluble calcium phosphate crosslinking within casein micelles as this increased bond mobility within rennet gels., (Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

There continues to be considerable public debate on the possible benefits regarding the growing popularity of the consumption of raw milk. However, there are significant concerns by regulatory, or public health, organizations like the Food and Drug Administration and the Centers for Disease Control and Prevention because of risk of contracting milkborne illnesses if the raw milk is contaminated with human pathogens. This review describes why pasteurization of milk was introduced more than 100 years ago, how pasteurization helped to reduce the incidence of illnesses associated with raw milk consumption, and the prevalence of pathogens in raw milk. In some studies, up to a third of all raw milk samples contained pathogens, even when sourced from clinically healthy animals or from milk that appeared to be of good quality. This review critically evaluates some of the popularly suggested benefits of raw milk. Claims related to improved nutrition, prevention of lactose intolerance, or provision of "good" bacteria from the consumption of raw milk have no scientific basis and are myths. There are some epidemiological data that indicate that children growing up in a farming environment are associated with a decreased risk of allergy and asthma; a variety of environmental factors may be involved and there is no direct evidence that raw milk consumption is involved in any "protective" effect.

Various types of polysaccharides are widely used in cultured dairy products. However, the interaction mechanisms, between milk proteins and these polysaccharides, are not entirely clear. To explore the interactions between uncharged and charged polysaccharides and the caseins, we used a model acid-milk-gel system, which allowed acidification to occur separately from gelation. The effect of adding uncharged dextran (DX; molecular weight ~2.0×10(6) Da) and negatively charged dextran sulfate (DS; molecular weight ~1.4×10(6) Da) to model acid milk gels was studied. Two concentrations (0.075 and 0.5%, wt/wt) of DX or DS were added to cold milk (~0°C) that had been acidified to pH values 4.4, 4.6, 4.8, or 4.9. Acidified milks containing DX or DS were then quiescently heated at the rate of 0.5°C/min to 30°C, which induced gelation, and gels were then held at 30°C for 17 h to facilitate gel development. Dynamic small-amplitude-oscillation rheology and large-deformation (shear) tests were performed. Microstructure of gels was examined by fluorescence microscopy. Gels made with a high concentration of DX gelled at a lower temperature, but after 17 h at 30°C, these gels exhibited lower storage moduli and lower yield-stress values. At pH 4.8 or 4.9 (pH values greater than the isoelectric point of caseins), addition of 0.5% DS to acidified milk resulted in lower gelation temperature. At pH 4.4 (pH values less than the isoelectric point of caseins), addition of 0.5% DS to acidified milk resulted in gels with very high stiffness values. Gels made at pH 4.8 or 4.9 with both concentrations of DS had much lower stiffness and yield-stress values than control gels. Microstructural analysis indicated that gels made at pH 4.4 with the addition of 0.5% DX exhibited large protein strands and pores, whereas gels made with 0.075% DX or the control gels had a finer protein matrix. At higher pH values (>4.4), gels made with 0.5% DX had a finer structure. At all pH values, gels made with 0.5% DS exhibited larger pores than the control gels. This study demonstrated that low concentrations of uncharged DX did not significantly affect the rheological properties of model acid milk gels; high concentrations of DX resulted in earlier gelation, possibly caused by depletion-induced attractions between casein particles, which altered the microstructure and created weaker gels. At pH values <4.6, negatively charged DS produced stiff casein gels, which might be due to attractive crosslinking by electrostatic interactions between DS and caseins at pH values below the isoelectric pH of casein (i.e., positively charged casein regions interacted with negatively charged DS molecules)., (Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Polysaccharides are often used to stabilize cultured milk products, although the nature of these interactions is not entirely clear. The objective of this study was to investigate phase behavior of milk protein dispersions with added dextran (DX; molecular weight = 2 × 10(6) Da) or dextran sulfate (DS; molecular weight = 1.4 × 10(6) Da) as examples of uncharged and charged polysaccharides, respectively. Reconstituted skim milk (5-20% milk solids, wt/wt) was acidified to pH 4.4, 4.6, 4.8, or 4.9 at approximately 0°C (to inhibit gelation) by addition of 3 N HCl. Dextran or DS was added to acidified milk samples to give concentrations of 0 to 2% (wt/wt) and 0 to 1% (wt/wt) polysaccharide, respectively. Milk samples were observed for possible phase separation after storage at 0°C for 1 and 24h. Possible gelation of these systems was determined by using dynamic oscillatory rheology. The type of interactions between caseins and DX or DS was probed by determining the total carbohydrate analysis of supernatants from phase-separated samples. At 5.0 to 7.5% milk solids, phase separation of milk samples occurred after 24h even without DX or DS addition, due to destabilization of caseins in these acidic conditions, and a stabilizing effect was observed when 0.7 or 1.0% DS was added. At higher milk solids content, phase separation was not observed without DX or DS addition. Similar results were observed at all pH levels. Gelation occurred in samples containing high milk solids (≥10%) with the addition of 1.0 to 2.0% DX or 0.4 to 1.0% DS. Based on carbohydrate analysis of supernatants, we believe that DX interacted with milk proteins through a type of depletion flocculation mechanism, whereas DS appeared to interact via electrostatic-type interactions with milk proteins. This study helps to explain how uncharged and charged stabilizers influence the texture of cultured dairy products., (Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

The objective of this study was to compare the effect of coagulant (bovine calf chymosin, BCC, or camel chymosin, CC), on the functional and sensory properties and performance shelf-life of low-moisture, part-skim (LMPS) Mozzarella. Both chymosins were used at 2 levels [0.05 and 0.037 international milk clotting units (IMCU)/mL], and clotting temperature was varied to achieve similar gelation times for each treatment (as this also affects cheese properties). Functionality was assessed at various cheese ages using dynamic low-amplitude oscillatory rheology and performance of baked cheese on pizza. Cheese composition was not significantly different between treatments. The level of total calcium or insoluble (INSOL) calcium did not differ significantly among the cheeses initially or during ripening. Proteolysis in cheese made with BCC was higher than in cheeses made with CC. At 84 d of ripening, maximum loss tangent values were not significantly different in the cheeses, suggesting that these cheeses had similar melt characteristics. After 14 d of cheese ripening, the crossover temperature (loss tangent = 1 or melting temperature) was higher when CC was used as coagulant. This was due to lower proteolysis in the CC cheeses compared with those made with BCC because the pH and INSOL calcium levels were similar in all cheeses. Cheeses made with CC maintained higher hardness values over 84 d of ripening compared with BCC and maintained higher sensory firmness values and adhesiveness of mass scores during ripening. When melted on pizzas, cheese made with CC had lower blister quantity and the cheeses were firmer and chewier. Because the 2 types of cheeses had similar moisture contents, pH values, and INSOL Ca levels, differences in proteolysis were responsible for the firmer and chewier texture of CC cheeses. When cheese performance on baked pizza was analyzed, properties such as blister quantity, strand thickness, hardness, and chewiness were maintained for a longer ripening time than cheeses made with BCC, indicating that use of CC could help to extend the performance shelf-life of LMPS Mozzarella., (Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

A major problem with reduced-fat cheese is the difficulty in attaining the characteristic flavor and texture of typical full-fat versions. Some previous studies have suggested that high hydrostatic pressure (HHP) can accelerate the ripening of full-fat cheeses. Our objective was to investigate the effect of HHP on reduced-fat (~7.3% fat) Cheddar cheese, with the goal of improving its flavor and texture. We used a central composite rotatable design with response surface methodology to study the effect of pressure and holding time on the rheological, physical, chemical, and microbial characteristics of reduced-fat Cheddar cheese. A 2-level factorial experimental design was chosen to study the effects of the independent variables (pressure and holding time). Pressures were varied from around 50 to 400 MPa and holding times ranged from 2.5 to 19.5 min. High pressure was applied 1 wk after cheese manufacture, and analyses were performed at 2 wk, and 1, 3, and 6 mo. The insoluble calcium content as a percentage of total Ca in cheeses were not affected by pressure treatment. Pressure applications ≥ 225 MPa resulted in softer cheese texture during ripening. Pressures ≥ 225 MPa increased melt, and resulted in higher maximum loss tangent values at 2 wk. Pressure treatment had a greater effect on cheese microbial and textural properties than holding time. High-pressure-treated cheeses also had higher pH values than the control. We did not observe any significant difference in rates of proteolysis between treatments. In conclusion, holding times of around 5 min and pressures of ≥ 225 MPa could potentially be used to improve the excessively firm texture of reduced-fat cheese., (Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

A process for the food-grade preparative-scale production and chromatographic purification of whey protein isolate (WPI)-dextran glycates was developed in this work. The Maillard reaction was used to produce the glycates in aqueous solution. A 5 mL cation exchange column and salt step gradients were utilized to elute the glycated protein at low salt and unreacted protein at high salt. The process was scaled-up 160-fold to an 800 mL column. Glycated products were analyzed by SDS-PAGE, BCA protein assay and glycoprotein carbohydrate estimation kit, MALDI-TOF and static and dynamic light scattering. Glycated protein was relatively pure, containing only traces of beta-lactoglobulin, and it was heterogeneous due to oligo-glycation. It had a molecular mass of 26-35 kDa by static light scattering, and 22-67 kDa by MALDI-TOF. Mono-glycated protein would have been 23.8 kDa from beta-lactoglobulin (18.6 kDa) and dextran (5.2 kDa). This work demonstrated the utility of cation exchange chromatography for the large-scale purification of glycated proteins using food-grade chemicals and procedures., (Copyright © 2012 Elsevier B.V. All rights reserved.)

The objective of this study was to identify DNA markers in the 4 casein genes (CSN1S1, CSN1S2, CSN2, and CSN3) and the 2 major whey protein genes (LALBA and LGB) that show associations with milk protein profile measured by reverse-phase HPLC. Fifty-three single nucleotide polymorphisms (SNP) were genotyped for cows in a unique resource population consisting of purebred Holstein and (Holstein × Jersey) × Holstein crossbred animals. Seven traits were analyzed, including concentrations of α(S)-casein (CN), β-CN, κ-CN, α-lactalbumin, β-lactoglobulin, and 2 additional secondary traits, the total concentration of the above 5 milk proteins and the α(S)-CN to β-CN ratio. A substantial fraction of phenotypic variation could be explained by the additive genetic component for the 7 milk protein composition traits studied. Moreover, several SNP were significantly associated with all examined traits at an experiment-wise error rate of 0.05, except for α-lactalbumin. Importantly, the significant SNP explained a large proportion of the phenotypic variation of milk protein composition. Our findings could be used for selecting animals that produce milk with desired composition or desired processing and manufacturing properties., (Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

The effect of increasing the colloidal calcium phosphate (CCP) content on the physical, rheological, and microstructural properties of yogurt was investigated. The CCP content of heated (85°C for 30 min) milk was increased by increasing the pH by the addition of alkali (NaOH). Alkalized milk was dialyzed against pasteurized skim milk at approximately 4°C for 72 h to attempt to restore the original pH and soluble Ca content. By adjustment of the milk to pH values 7.45, 8.84, 10.06, and 10.73, the CCP content was increased to approximately 107, 116, 123, and 128%, respectively, relative to the concentration in heated milk. During fermentation of milk, the storage modulus (G') and loss tangent values of yogurts were measured using dynamic oscillatory rheology. Large deformation rheological properties were also measured. The microstructure of yogurt was observed using fluorescence microscopy, and whey separation was determined. Acid-base titration was used to evaluate changes in the CCP content in milk. Total Ca and casein-bound Ca increased with an increase in the pH value of alkalization. During acidification, elevated buffering occurred in milk between pH values 6.7 to 5.2 with an increase in the pH of alkalization. When acidified milk was titrated with alkali, elevated buffering occurred in milk between pH values 5.6 to 6.4 with an increase in the pH of alkalization. The high residual pH of milk after dialysis could be responsible for the decreased contents of soluble Ca in these milks. The pH of gelation was higher in all dialyzed samples compared with the heated control milk, and the gelation pH was higher with an increase in CCP content. The sample with highest CCP content (128%) exhibited gelation at very high pH (6.3), which could be due to alkali-induced CN micellar disruption. The G' values at pH 4.6 were similar in gels with CCP levels up to 116%; at higher CCP levels, the G' values at pH 4.6 greatly decreased. Loss tangent values at pH 5.1 were similar in all samples except in gels with a CCP level of 128%. For dialyzed milk, the whey separation levels were similar in gels made from milk with up to 107% CCP but increased at higher CCP levels. Microstructure of yogurt gels made from milk with 100 to 107% CCP was similar but very large clusters were observed in gels made from milk with higher CCP levels. By dialyzing heated milk against pasteurized milk, we may have retained some heat-induced Ca phosphate on micelles that normally dissolves on cooling because, during dialysis, pasteurized milk provided soluble Ca ions to the heated milk system. Yogurt texture was significantly affected by increasing the casein-bound Ca (and total Ca) content of milk as well as by the alkalization procedure involved in that approach., (Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Three Hofmeister salts (HS; sodium sulfate, sodium thiocyanate, and sodium chloride) were evaluated for their effect on the textural and rheological properties of nonfat cheese. Nonfat cheese, made by direct acidification, were sliced into discs (diameter=50 mm, thickness=2 mm) and incubated with agitation (6 h at 22°C) in 50 mL of a synthetic Cheddar cheese aqueous phase buffer (pH 5.4). The 3 HS were added at 5 concentrations (0.1, 0.25, 0.5, 0.75, and 1.0 M) to the buffer. Post-incubation, cheese slices were air dried and equilibrated in air-tight bags for 18 h at 5°C before analysis. Small amplitude oscillatory rheology properties, including the dynamic moduli and loss tangent, were measured during heating from 5 to 85°C. Hardness was determined by texture profile analysis. Acid-base buffering was performed to observe changes in the indigenous insoluble (colloidal) calcium phosphate (CCP). Moisture content decreased with increasing HS concentration. Cheeses incubated in high concentrations of SCN(-) softened earlier (i.e., loss tangent=1) compared with other HS treatments. Higher melting temperature values were observed for cheeses incubated in high concentrations of SO(4)(2-). Hardness decreased in cheeses incubated in buffers with high concentrations of SCN(-). The indigenous CCP profile of nonfat cheese was not greatly affected by incubation in Cl(-) or SCN(-), whereas buffers with high concentrations of SO(4)(2-) reduced the acid-base buffering contributed by CCP. The use of high concentrations (1.0M) of SCN(-) for incubation of cheeses resulted in a softer protein matrix at high temperatures due to the chaotropic effect of SCN(-), which weakened hydrophobic interactions between CN. Cheese samples incubated in 1.0M SO(4)(2-) buffers exhibited a stiffer protein matrix at high temperatures due to the kosmotropic effect of SO(4)(2-), which helped to strengthen hydrophobic interactions in the proteins during the heating step. This study showed that HS influenced the texture and rheology of nonfat cheese probably by altering the strength of hydrophobic interactions between CN., (Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Calcium-chelating salts (CCS), such as phosphates and citrates, are often added to milk systems to modify physical properties like heat stability. The objective of this study was to investigate the effect of binary CCS mixtures on the properties of casein (CN) micelles including the distribution of Ca between the soluble and CN-bound states. Six binary CCS mixtures were prepared from 4 different types of CCS [i.e., trisodium citrate (TSC), disodium phosphate (DSP), tetrasodium pyrophosphate (TSPP), and sodium hexameta phosphate (SHMP)] by combining 2 CCS at a time in 5 different proportions (8.3:91.7, 29.2:70.8, 50:50, 70.8:29.2, and 91.7:8.3). Different concentrations of these mixtures (0, 0.1, 0.3, 0.5, and 0.7% wt/wt) were added to milk protein concentrate solutions (5% wt/wt) at pH 5.8. The ability of CCS to disperse CN particles and its interaction with Ca were assessed from turbidity measurements, acid-base titration behavior, and the quantity of CN-bound Ca and inorganic phosphate (Pi). Turbidity and the buffering peak at pH ∼5.0 during acid titration decreased with an increasing concentration of CCS. This was due to the chelation of Ca and the dispersion of CN micelles. The presence of TSC in mixtures decreased the amount of CN-bound Ca and Pi; however, the presence of TSPP in mixtures increased CN-bound Ca and Pi. When DSP was present at high proportions in mixtures of CCS, the CN-bound Ca and Pi slightly increased. When SHMP was used in mixtures of CCS, CN-bound Ca and Pi increased with the use of a low proportion of SHMP but decreased when SHMP was used at high proportions in the mixture. Combinations of DSP-TSPP used in the proportions 29.2:70.8, 50:50, and 70.8:29.2 resulted in the gelation of milk protein concentrates when the total CCS concentration was ≥0.3%. These results indicated that the type of CCS present in a mixture modified CN properties by various mechanisms, including chelation of Ca, dispersion of CN micelles, and formation of new types of Ca-CCS complexes. The type of interaction between the newly formed Ca-CCS complexes and the dispersed CN depended on the proportion, concentration, and type of CCS present in the mixtures. This information is useful in understanding how mixtures of CCS affect CN properties., (Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

Colloidal calcium phosphate (CCP) plays a key role in the formation and integrity of casein (CN) micelles. However, limited information is available on the molecular weight (M(w)) of CCP. Recently, we theoretically derived the M(w) of CCP and the objectives of this study were to experimentally determine the M(w) of CCP. We used 2 methods to prepare CCP fractions: skim milk was enzymatically digested with either trypsin or a combination of papain and proteinase enzymes to remove most CN. The CN phosphopeptides are resistant to trypsin hydrolysis. Digestion was carried out in a membrane tube that was dialyzed against the same bulk milk used in sample preparation to remove small peptides and to minimize perturbation of CCP. After digestion, the protein contents of the enzyme-treated milks were 0.92 and 0.36% for the trypsin and papain-proteinase treatments, respectively. Size-exclusion chromatography, coupled with multi-angle laser light scattering, was used to separate the CCP-phosphopeptide fraction from the digested mixture. Simulated milk ultrafiltrate was used as a mobile phase during size-exclusion chromatography separation to try to preserve the integrity of CCP. Size-exclusion chromatography peaks, which had higher Ca and P contents than the baseline, were identified as the likely fractions containing the phosphopeptide-stabilized CCP; this peak eluted with retention times of 100 to approximately 110 min for trypsinated samples. The papain-proteinase treatment caused excessive loss of CN that were needed to stabilize CCP, which resulted in no obvious peak that had elevated Ca and P contents. Debye plots at these retention times indicated that the weight-average M(w) for the fraction prepared by trypsin was 17,450 g/mol. Attempts to estimate the M(w) of the phosphopeptides associated with CCP using sodium dodecyl sulfate-PAGE were not successful, as we did not observe any peptide bands in these gels, presumably because of their low concentration in the isolated, unconcentrated fraction. Assuming that 4 CN phosphopeptides stabilized each CCP and if the M(w) of each of these phosphopeptides was about 2,500 g/mol, then the M(w) of CCP would be around 7,450 g/mol. This experimental value was close to the theoretically-derived M(w) of 4,897 and 9,757 g/mol for tetrahedron and bi-pyramid shaped objects, respectively, when using the brushite form of calcium phosphate., (Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)

A curd-washing step is used in the manufacture of Colby cheese to decrease the residual lactose content and, thereby, decrease the potential formation of excessive levels of lactic acid. The objective of this study was to investigate the effect of different washing methods on the Ca equilibrium and rheological properties of Colby cheese. Four different methods of curd-washing were performed. One method was batch washing (BW), where cold water (10°C) was added to the vat, with and without stirring, where curds were in contact with cold water for 5 min. The other method used was continuous washing (CW), with or without stirring, where curds were rinsed with continuously running cold water for approximately 7 min and water was allowed to drain immediately. Both methods used a similar volume of water. The manufacturing pH values were similar in all 4 treatments. The insoluble (INSOL) Ca content of cheese was measured by juice and acid-base titration methods and the rheological properties were measured by small amplitude oscillatory rheology. The levels of lactose in cheese at 1 d were significantly higher in CW cheese (0.06-0.11%) than in BW cheeses (∼0.02%). The levels of lactic acid at 2 and 12 wk were significantly higher in CW cheese than in BW cheeses. No differences in the total Ca content of cheeses were found. Cheese pH increased during ripening from approximately 5.1 to approximately 5.4. A decrease in INSOL Ca content of all cheeses during ripening occurred, although a steady increase in pH took place. The initial INSOL Ca content as a percent of total Ca in cheese ranged from 75 to 78% in all cheeses. The INSOL Ca content of cheese was significantly affected by washing method. Stirring during manufacturing did not have a significant effect on the INSOL Ca content of cheese during ripening. Batch-washed cheeses had significantly higher INSOL Ca contents than did CW cheeses during the first 4 wk of ripening. The maximum loss tangent values (meltability index) of CW cheese at 1 d and 1 wk were significantly higher compared with those of BW cheeses. In conclusion, different curd washing methods have a significant effect on the levels of lactose, lactic acid, meltability, and INSOL Ca content of Colby cheese during ripening., (Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.)