Search

The most important factors that influence the sustainability of the adhesive technology are the sources of raw materials, energy consumption in the production process, and impact on environmental pollution. The usual formulation of the adhesive contains base polymer component derived mostly from non-renewable sources of oil and various other additives, and in some types of adhesives the liquid media are organic solvents or water. The environmental sustainability of the adhesive technology depends on the justification of the choice of raw material and additives, and especially today, the decreasing fraction of organic solvents in the formulations.This paper presents an analysis of production and shares of certain types of adhesives, depending on the polymer component in Western Europe in comparison with the production program of Croatian small-medium manufacturer Metakem d. o. o., Ludbreg.From the comparison of the presented data for the factory Metakem and the Western European market (Fig. 1), it is evident that Metakem’s manufacturing program includes products for almost all major market segments that use adhesives. Differences in the percentage share reflects Metakem production capability, but also the demand for some types of glue on the local market. From the data presented, it is evident that adhesives have a very wide application and occupy an important position in many other industries. Hence, the sustainability of the adhesive technology isextremely important.Considering the origin of raw polymer materials in Metakem production program, as well as in the Western European market (Fig. 2), the analysis has revealed that most of the adhesives product range is based on synthetic polymeric materials obtained from non-renewable sources of oil. Thus, today’s bioadhesives research topics are focused on finding new sources of polymer materials based on natural raw materials, which can meet the appropriate quality requirements compared with those achieved by adhesive formulations based on synthetic polymers.An important criterion of environmental sustainability is the lower content of volatile organic compounds in the adhesive. Compared to the Western European market, it is evident that solvent- based adhesives are still an essential part of Metakem’s production program (Fig. 3). Based on the characteristics of the solvents used in adhesive formulations at Metakem (Table 1) it can be concluded that they are not harmful to the environment in terms of negative impact on the ozone layer or bioaccumulation. However, all the solvents in high concentrations or prolonged inhalation may seriously endanger human health, and therefore special attention is required when these solvents are used in adhesive formulations. Generally, there is an increasing trend in production of water-based adhesives in the world because of environmental acceptability and mandatory legal regulations

In this paper, the influence of flame treatment on the surface properties of polypropylene (PP) and thermoplastic polyolefins with talc and carbon black filler (TPO), and adhesion of the applied coating in the conditions of industrial robotic dyeing process were investigated. The flame treatment was carried out at two distances from the flame (7.5 cm and 12.5 cm) at constant air and methane flows as well as speed of the burner. The thermal stability of untreated samples was investigated using thermogravimetric analysis (TGA). The change in thermal properties before and after flame treatment was investigated using differential scanning calorimetry (DSC). Changes of the samples’ surface energy were examined before flame treatment, 1 h and 24 h after flame treatment, by the contact angle method. Qualitative analysis of the surface chemical composition, before and after flame treatment, was performed by ATR – FTIR analysis, and morphological changes by scanning electron microscopy (SEM). After applying the base layer, dye and topcoat on the surface of the treated samples, the adhesion was determined by standard methods ISO 2409 and ISO 16925/D25 2018-B. The results showed that TPO containing talc and carbon black filler have better thermal stability compared to PP. Flame treatment influenced the surface characteristics of the samples, namely the increase in surface free energy and the appearance/structure of the surface. With ATR – FTIR, the existence of polar groups on the surface after flame treatment were determined. According to the standards, all dyed samples met the requirements of excellent adhesion on the substrate/coating interface. [ABSTRACT FROM AUTHOR]

Copyright of Kemija u Industriji is the property of Croatian Society of Chemical Engineers and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Kemija u Industriji is the property of Croatian Society of Chemical Engineers and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

In this work, the influence of multiwalled carbon nanotubes (MWCNT) and carbon nanotubes modified with COOH groups (MWCNT-COOH) on the structure and properties of thermoplastic polyurethane (PU) were investigated. The samples of nanocomposite were prepared from a mixture of polyurethane and MWCNT in acetone by slow drying at room temperature. The effect of the addition of nanofillers on the spherulite structure of polyurethane and the distribution of the nanofillers in the PU matrix were analysed with optical polarization microscopy. Thermal properties in non-isothermal and isothermal conditions were investigated by differential scanning calorimetry (DSC). The results of contact angle measurement imply that modification of MWCNT surface with COOH groups changes its surface from hydrophobic to hydrophilic (Fig. 2 and Table 1). Optical polarization microscopy showed that the addition of both nanofillers disrupts the coarse spherulite morphology of the polyurethane matrix (Fig. 4 and Fig. 5). It was observed that, at the macro level, the modified MWCNT-COOH filler is better distributed in the PU matrix than is the MWCNT filler (Fig. 5). The DSC results showed that, in non-isothermal conditions, up to a certain amount, both nanofillers accelerate the crystallization of the soft segments of polyurethane. This effect is more pronounced in systems with MWCNT filler (Fig. 9). The results of the crystallization enthalpy during cooling showed that MWCNT filler, despite its worse distribution in the PU matrix, more significantly enhances crystallization of PU’s soft segment than does the MWCNT-COOH filler (Fig. 10). This conclusion can be ascribed to better compatibility between the nonpolar MWCNT filler and the nonpolar soft phase of the PU matrix, as well as to the previous scientific finding that functional groups at MWCNT surface decrease the nucleation effect of MWCNT. By analysing the melting peaks, it can be concluded that the PU systems with MWCNT compared to systems with MWCNT-COOH contain a higher proportion of less ordered crystalline soft phase (Fig. 11). In isothermal conditions, the MWCNT filler accelerates crystallization more significantly than does the MWCNT-COOH filler (Fig. 16). [ABSTRACT FROM AUTHOR]

In this research, the influence of titanium dioxide (TiO 2 ) nanoparticles and their modifications on the weathering resistance of untreated and heat-treated wood was studied. The wood samples were coated with polyacrylate waterborne emulsion coatings that contain nano-TiO 2 in the amount of 0.75 wt.%. Two types of modifiers were used to modify the nano-TiO 2 surface: 2,2'-azobis(2-methylpropionamide) dihydrochloride (AIBA) and 3-aminopropyltrimethoxy silane (AMPTS). Coated and uncoated wood samples were exposed to accelerated weathering by application of sunlight, water and moisture for 360 h. During the research, the dry film thickness, color, gloss and hardness of the surface of the samples were measured. The obtained results showed that the effect of the addition and surface modification of nano-TiO 2 on the color and gloss stability was different on untreated and heat-treated ash wood, and that accelerated weathering causes an increase in surface hardness and a decrease in thickness of the dry coating.

Klebsiella pneumoniae is an emerging multidrug-resistant pathogen that can contaminate hospital surfaces in the form of a biofilm which is hard to remove with standard disinfectants. Because of biofilm resistance to conservative disinfectants, the application of new disinfection technologies is becoming more frequent. Ozone gas has antimicrobial activity but there is lack of data on its action against K. pneumoniae biofilm. The aim of this study was to investigate the effects and mechanisms of action of gaseous ozone on the OXA-48-procuding K. pneumoniae biofilm. A 24 h biofilm of K. pneumoniae formed on ceramic tiles was subsequently exposed to different concentrations of ozone during one and two hours to determine the optimal ozone concentration. Afterwards, the total bacteria count, total biomass and oxidative stress levels were monitored. A total of 25 ppm of gaseous ozone was determined to be optimal ozone concentration and caused reduction in total bacteria number in all strains of K. pneumoniae for 2.0 log 10 CFU/cm 2 , followed by reduction in total biomass up to 88.15%. Reactive oxygen species levels significantly increased after the ozone treatment at 182% for the representative K. pneumoniae NCTC 13442 strain. Ozone gas in the concentration of 25 ppm caused significant biofilm reduction but did not completely eradicate the K. pneumoniae biofilm formed on ceramics. In conclusion, ozone gas has great potential to be used as an additional hygiene measure in joint combat against biofilm in hospital environments.

Bacterial contamination of the membranes used during guided bone regeneration directly influences the outcome of this procedure. In this study, we analyzed the early stages of bacterial adhesion on two commercial dense polytetrafluoroethylene (d-PTFE) membranes in order to identify microstructural features that led to different adhesion strengths. The microstructure was investigated by X-ray diffraction (XRD), differential scanning calorimetry (DSC), and Fourier transform infrared (FTIR). The surface properties were analyzed by atomic force microscopy (AFM), scanning electron microscopy (SEM), and surface free energy (SFE) measurements. Bacterial properties were determined using the microbial adhesion to solvents (MATS) assay, and bacterial surface free energy (SFE) was measured spectrophotometrically. The adhesion of four species of oral bacteria ( Streptococcus mutans , Streptococcus oralis , Aggregatibacter actinomycetemcomitas , and Veilonella parvula ) was studied on surfaces with or without the artificial saliva coating. The results indicated that the degree of crystallinity (78.6% vs. 34.2%, with average crystallite size 50.54 nm vs. 32.86 nm) is the principal feature promoting the adhesion strength, through lower nanoscale roughness and possibly higher surface stiffness. The spherical crystallites ("warts"), observed on the surface of the highly crystalline sample, were also identified as a contributor. All bacterial species adhered better to a highly crystalline membrane (around 1 log 10 CFU/mL difference), both with and without artificial saliva coating. Our results show that the changes in polymer microstructure result in different antimicrobial properties even for chemically identical PTFE membranes.