Search

A new simplified low temperature deposition method to manufacture flexible transparent conductive electrodes (FTCE) based on conductive polymer composite filled with silver nanowires (AgNWs) was investigated. Polyurethane/AgNWs composite was deposed on a poly(ethylene terephthalate) substrate as a conductive paint in a thin layer lower than 2 μm. The high aspect ratio nanowires influence on the electrical behavior is followed with surface resistivity and optical transparency experiments. The best compromise was obtained with a conductive layer filled with 2.84 vol.% of AgNWs; it exhibits a surface resistivity of 143 Ω/sq with 73% in transmittance. These transparent conductive composites processing in one step with good touching manipulation resistance demonstrate the real interest for this kind of FTCEs technology without indium tin oxide. [ABSTRACT FROM AUTHOR]

The aim of this work is to study electrically conductive composites from an epoxy matrix loaded with silver nanowires (AgNWs). Dynamic mechanical analysis (DMA) and dynamic dielectric spectroscopy (DDS) were used to study the molecular mobility of the epoxy matrix and its epoxy/AgNWs composites. The influence of the epoxy/amine ratio on the macroscopic properties was analyzed. The loss modulus of the epoxy matrix highlights two major relaxations, β and α. The β relaxation is due to the localized mobility initiated by hydroxyl groups. The α trelaxation is the anelastic effect liberated at the glass transition. The introduction of a small amount of AgNWs (<8 vol%) has practically no influence on the mechanical properties of the glassy state. For the rubbery state, AgNWs cause an increase in the storage modulus as a function of the filler content. The loss modulus profile is modified: The ω relaxation due to heterogeneities of the 3D network is observed independently from the hydration level of composites. The magnitude of the α mode is increased due to the stick–slip phenomenon. Moreover, it is shifted toward lower temperatures upon the introduction of AgNWs. In other words, the activation enthalpy decreases for both modes. Electrical study through DDS and conductivity measurement of epoxy/AgNWs composites shows the consequence of a lower relative degree of conversion caused by the insertion of AgNWs. Epoxy/AgNWs composites allow us to obtain one of the highest values of the electrical conductivity for polymer‐based composites without any drastic evolution of mechanical properties. [ABSTRACT FROM AUTHOR]

For electromagnetic shielding in space environment, the metallization of carbon fiber reinforced polymer (CFRP) is required. A specific attention is paid due to the thermal expansion coefficient difference between substrate and metal coating. A surface metallization of a CFRP has been elaborated by electrodeposition. This study presents an original process based on an electrically conductive polymer coating elaborated from a polyurethane matrix filled with a low content of silver nanowires (<10%vol). A continuous and adherent deposit is obtained by an optimization of the electroplating parameters. A minimal volume fraction was determined at 3%vol associated with an applied current density estimated near 0.1 A/dm2. The growth speed is 7 μm/h at 0.1 A/dm2. The adhesion was checked in severe environmental conditions (−196 to 165°C). The effectiveness shielding obtained with this solution reaches an attenuation value higher than 90 dB between 1 and 26 GHz necessary for space communication applications. [ABSTRACT FROM AUTHOR]

A new kind of high electrical conductive epoxy coating with low filler rate was investigated for lightning strike protection (LSP) of carbon fiber reinforced polymer (CFRP). The coating without CFRP substrate was firstly studied. The influence of silver submicronic wires (AgSWs) with a high aspect ratio on the electrical behavior is observed; that is, the electrical resistivity evolution, the current density value, and the electrical conduction mechanisms as function of temperature. The preponderant electrical conduction mechanism is an Ohmic behavior. The higher level of conductivity obtained is 5.5 × 105 S m−1 for 9% vol of AgSWs. Lightning strike tests were carried out on an epoxy/AgSWs coating filled with 8% in volume (74 gsm) and deposited on a CFRP. The ultrasonic testing after lightning strike on coated CFRP shows no structural delamination and demonstrates the interest of this new route for an efficient LSP. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 137, 48700. [ABSTRACT FROM AUTHOR]

The article presents a reflection on the question of the reorganization of the market economy as a way to save Europe from the global crisis that started in 2008. The notion of creation of value is discussed via the theme of capital gain and what is made of it. The themes of self-financing and exchange economy are examined. The problem of the organization of capitalism without normalized profit rates and without the automatic publication of these rates is pointed out. The question of the regulation of profit and of what regulates profit is addressed.