Search

Anti-sliding stability safety is a critical issue that must be given sufficient and widespread attention during the entire lifecycle of gravity dams. The calculated anti-sliding stability safety factor (ASS-SF) is usually compared with the allowable value required by the standards in the traditional method, which ignores the influence of material parameter uncertainties and leads to unreasonable safety evaluation results. Therefore, the nonlinear functional relationship between the stability safety factor (SF) and the random variable parameters is constructed based on the response surface equations, and the distribution types of SF sequences calculated by the Monte Carlo sampling are determined, then a probabilistic stability evaluation method for concrete gravity dams is proposed. Engineering application shows that the calculated SF obeys the normal distribution; the minimum guaranteed rate of different sliding paths in a gravity dam is 86.66%, and the guaranteed rate for the overload safety factor (OSF) is 36.00%. The results imply that a guaranteed rate for the allowable value of the ASS-SF should be provided when making the stability safety evaluation of the dams, especially the OSF. The outcome of this research will advance the understanding of stability evaluation of concrete dams, and reduce the potential risk of sliding instability of concrete dams.

The performance of corrosion-induced cracking of reinforced concrete members under transverse constraints was studied. Based on the theory of elastic-plastic mechanics and the hypothesis of uniform corrosion of a steel bar, a three-layer hollow cylinder model was established to predict the critical corrosion of the steel bar at the time of the cracking of the concrete cover. Taking the constraint of stirrups on surrounding concrete into consideration, it can be used to predict the corrosion rate of members with stirrups at the time of the cracking of the concrete cover, which further expands the application range of the corrosion-induced cracking models of concrete. On this basis, the critical corrosion rate of concrete under different stirrup ratios at the time of cracking was measured. The calculated results of the model are in accordance with experimental data. For corner steel bars, when the stirrup spacing is less than 100 mm, the existence of stirrups can effectively delay the occurrence of rust expansion cracks and enhance the durability of the structure. On the basis of this study, the problem of corrosion expansion and cracking of the concrete cover caused by non-uniform corrosion of steel bars along longitudinal and radial directions needs to be further studied in the future.

Abstract Dam numerical simulation is an important method to research the dam structural behavior, but it often takes a lot of time for calculation when facing problems that require many simulations, such as structural parameter back analysis. The surrogate model is widely used as a technology to reduce computational cost. Although various methods have been widely investigated, there are still problems in designing the surrogate model's optimal Design of Experiments (DoE). In addition, most of the current DoE focuses on establishing a single-output problem. Designing a reasonable DoE for high-dimensional outputs is also a problem that needs to be solved. Based on the above issues, this research proposes a sequential surrogate model based on the radial basis function model (RBFM) with multi-outputs adaptive sampling. The benchmark function demonstrates the applicability of the proposed method to single-input & multi-outputs and multi-inputs & multi-outputs problems. Then, this method is applied to establishing a surrogate model for dam numerical simulation with multi-outputs. The result demonstrates that the proposed technique can be sampled adaptively and samples can be targeted based on the function form of the surrogate model, which significantly reduces the required sampling and calculation cost.

In the numerical simulation of earth-rock dam, accurate and reliable mechanical parameters of the dam material are the important basis for dam deformation predictions and dam safety evaluations. Based on the deformation monitoring data of Luding core wall rockfill dam, the rheological parameters of rockfill and core wall materials are inverted in this paper. Combined with the actual filling and impoundment process of the dam, the numerical simulation is carried out, and the stress deformation and differential settlement of the dam after completion and impoundment are analyzed. The results showed that the stress deformation results of the dam based on the inversion parameters were in good agreement with the actual deformation. The horizontal displacement, settlement, and principal stress of the dam during the completion period were symmetrically distributed along the core wall. The maximum horizontal displacement occurred at the main dam on both sides of the core wall and the upstream and downstream dam slopes, and the maximum settlement occurred in the middle of the core wall. During the impoundment period, under the action of reservoir water pressure and upstream rockfill wetting deformation, the deformation and stress of the dam body no longer met the symmetrical distribution law, and the maximum horizontal displacement of the dam body during the impoundment period was located at 2/3 of the upstream dam slope. The maximum settlement of the dam body was located at 1/2 of the dam height. The maximum principal stress on the upstream side of the core wall was located on the left side of the bottom of the core wall, and the minimum principal stress was also located on the left side of the bottom of the core wall. The simulation results of the deformation and stress met the general law of earth-rock dam engineering. During the completion period, the deformation inclination of the dam crest was less than 1%. During the impoundment period, the deformation inclination of the dam crest area increased due to the wetting deformation of the upstream rockfill material. At the same time, the deformation inclination of the dam crest axis was larger than that of the upstream and downstream sides, and the deformation inclination of the dam crest at the middle of the valley was the largest, but it did not exceed 3%, that is, there would be no longitudinal cracks, which is consistent with the actual situation. The research results can better predict the stress deformation and crack of the dam body, and provide important support for dam safety evaluations.

The wetting deformation of the upstream dam shell material during the impoundment of the core wall rockfill dam seriously affects the safety of the dam. Based on the proposed Ew−νw wetting model, this paper proposes its corresponding two methods to simulate the collapse settlement of the rockfill dam: the initial strain method and the initial stress method. By simulating the collapse settlement of the Guanyinyan core wall rockfill dam, it is found that the simulated result using the initial stress method is in good agreement with the field monitoring data, while the displacement simulated using the initial strain method is larger. The distribution of displacement contours simulated using the initial strain method is obviously inconsistent in the area where the wetting deformation occurs, and the simulation results of the initial stress method are more reasonable. With the rise in the water level, the wetting deformation of the upstream dam shell material causes the tensile stress zone at the top of the dam. Therefore, the wetting deformation is the direct cause of the crack at the top of the dam, and the initial stress method should be preferred in the simulation of the wetting deformation of rockfill materials.