Search

To fill the research gap in the mechanical and physical properties of different varieties of sweet potatoes at different points in the harvest period and to provide a theoretical basis for the design of key components of the sweet potato harvester, the physical properties of Su-Shu 16, Su-Shu 36, and Ning-Zi 4 during the harvest period were studied at three time points: 15 October, 25 October, and 4 November 2023. The moisture content of sweet potatoes was determined using the DGF30/7-IA electric hot air-drying oven. The results showed that the moisture content of sweet potatoes decreased with increasing growth time at three different time points during the harvest period. The moisture content of Su-Shu 16 was, on average, 12.74% higher than that of Su-Shu 36, while the moisture content of Ning-Zi 4 was, on average, 8.07% higher than that of Su-Shu 36. The density of Su-Shu 36 measured by the drainage method is greater than that of Su-Shu 16 and Ning-Zi 4, but the difference is relatively small, and the density tends to decrease slowly with the increase of growth time. Using an electronic universal testing machine, compression tests were conducted on Su-Shu 16, Su-Shu 36, and Ning-Zi 4 at loading speeds of 5 mm/min and 10 mm/min, respectively. The results showed that the compressive strength limit range of Su-Shu 36 was slightly higher than that of Su-Shu 16 and significantly higher than that of Ning-Zi 4. The Poisson’s ratio, elastic modulus, and shear modulus values of Su-Shu 16 and Su-Shu 36 were similar and much higher than those of Ning-Zi 4. Studying sweet potatoes’ growth and physical characteristics for different purposes can provide data references for the design of digging depth, working width, and conveyor chain gap of sweet potato harvesters, as well as data references for sweet potato simulation experiments.

This paper used the 4UM-120D electric leafy vegetable harvester as the research object and designed a travel speed automatic control system to maintain the travel speed within a set value of ±2% in order to improve the efficiency and quality of leafy vegetable harvester operations and decrease the work intensity of the operator. The harvester’s travel speed was automatically controlled by using the PID, adaptive fuzzy PID, and sliding mode control techniques after the mechanical and electrical equations for the travel drive motor (a DC brushless motor) were established in MATLAB. By simulating various working situations, the stability, accuracy, and speed of the automatic control system were compared and analyzed using the adjustment time, overshoot, steady-state transition time, and maximum deviation from the set speed as evaluation indicators. The test results revealed that when the current value of the leafy vegetable harvester travel speed deviated from the set value by more than 2%, the dynamic response performance and stability of the DC brushless motor travel drive system based on the sliding mode control strategy was significantly better than that of the PID and adaptive fuzzy PID control strategies, and its anti-disturbance was stronger, achieving the function of automatic control of the harvester travel speed. When the travel motor started with a constant load and the sliding mode control strategy’s parameters were the gain factors A = 1/70, c = 100, ε = 100, and k = 100, the travel drive system regulation time was 1.5 s, and the overshoot was 10%. When the harvester was operating smoothly and had leafy vegetable collection baskets loaded and unloaded, the steady-state transition time was 0.3 s. According to the actual engineering application experience, the specific technical state of the control strategy of the agricultural machinery travel speed automatic control system was: regulation time 2.5~3 s; overshoot amount 20~25%; and steady-state transition time 1.0~1.5 s, so the travel speed automatic control system of the electric leafy vegetable harvester in sliding mode was in line with the technical state requirements. The results of the field trials demonstrated the accuracy of the simulation test results. This study offered a method to lessen the work intensity of operators and increase the operating efficiency and quality of a leafy vegetable harvester.

At present, all most sweet potato crushing machineries are improved based on potato seedling killer or straw crushing and returning the machine and adopt single-roller mulch type seedling killing structure, and there are problems such as low crushing qualification rate of ridge vines, easy entanglement of stalks, and high damage rate. This not only requires manual further removal of the vines, but also the damaged sweet potato cannot be stored, which affects the yield. To solve the problems, a double-roller sweet potato vine crushing and returning machine with the structure of the front roller picking and the back roller crushing was designed. The Box-Behnken test design method was adopted to establish a quadratic regression model that took the picking roller speed, the cutter roller speed, and the ground clearance as the test factors, and the vines breaking qualified rate, the stubble height, and the sweet potato damage rate as evaluating indicators. The analysis of the influence of interactive factors showed that the contribution rate of each factor to the vines breaking qualified rate was picking roller speed> cutter roller speed > ground clearance; the contribution rate of each factor to the stubble height was ground clearance> pickling roller speed > cutter roller speed; the contribution rate of various factors to the sweet potato damage rate was ground clearance> cutter roller speed > pickling roller speed. The optimization results showed that when the picking roller speed was 631 r/min, the cutter roller speed was 1906 r/min, and the ground clearance was 21 mm, the vines breaking qualified rate was 96.2%, the stubble height was 28.8 mm, and the sweet potato damage rate was 0.16%. The research results can provide new test schemes and complete design parameters for sweet potato vine crushing operations.

To improve the level of precise seeding mechanization of potato micro-seed, a new type of pneumatic cleaning system has been designed. The system adopts a pneumatic cleaning method to achieve precise seeding. Based on analyzing the force of potato micro-seed, the parameters of cleaning airflow velocity and spoon negative pressure have been determined. The test bench of the seeding device has been built and the Box-Behnken test design method has been adopted. Taking the cleaning airflow velocity, the spoon negative pressure, the driving wheel velocity and the seed layer height as the test factors, the missing seed index and the qualified seed index as the evaluation indicators, the quadratic regression orthogonal test has been performed to optimize and determine the best combination of each parameter. Test results showed that when the cleaning airflow velocity was 26.6 m/s, the spoon negative pressure was 4.2 KPa, the driving wheel velocity was 43.7 r/min, and the seed layer height was 32.9 cm, the missing seed index was 1.5% and the qualified seed index was 93.2%. The system can realize single precise seeding of potato micro-seed seeding.

In this study, a 4UM-120D electric leafy vegetable harvester was employed as the research object. An automatic control system was created to maintain the cutter’s height above the ground within ±2% of the desired value. The intention was to reduce the operators’ work intensity while improving the leafy vegetable harvester’s working quality. The automatic control system for the cutter height from the ground was explained, along with its structure and operating philosophy. MATLAB was used to establish the two-phase hybrid stepper motor’s mathematical electrical equation and mechanical equation models. An analysis was carried out on the fundamentals and differences between position PID and incremental PID control algorithms. Utilizing incremental PID in combination, the control strategy for the harvester cutter height from the ground was built, and an automatic control system was produced under the corresponding control strategy. The stability, accuracy, and rapidity of the automatic control system of the cutter height from the ground under the incremental PID control strategy were analyzed by simulating different actual working conditions with MATLAB/Simulink and taking the steady-state transition time as the evaluation index. The test results show that when the deviation between the current value and the set value was greater than 2%—that is, when the harvester was in the condition of suddenly crossing the ditch or suddenly climbing the slope—the automatic control system based on the incremental PID control strategy had a good dynamic response performance and stability. This resulted in the automatic control function of the harvester cutter height off the ground being achieved. When the rotation angle PID control algorithm’s proportional coefficient is Kp = 4.665, the rotation speed PID control algorithm’s proportional coefficient is Kp = 5.65 and its integral coefficient is Ki = 3.86, and the current PID control algorithm’s proportional coefficient is Kp = 0.5455 and its integral coefficient is Ki = 30.4578. The harvester abruptly crossed a ditch while operating steadily, and the automatic control system’s steady-state transition time for the height of the cutter off the ground was 1.0811 s. The harvester abruptly climbed a slope while operating steadily, and the automatic control system’s steady-state transition time for the height of the cutter off the ground was 1.1185 s. Data from the field tests revealed a degree of reliability in the simulation test results. The study offered a strategy for raising the harvester quality for leafy vegetables while lowering the operator workload.

The yield of sweet potato vines is large, making it a good source of food. However, it is difficult to harvest sweet potato vines due to creeping and intertwining. Therefore, according to the domestic sweet potato planting model, this paper designed a double roll sweet potato vine harvester which can complete the operations of vine picking, vine killing, conveying and header harvesting at one time. The machine adopts the process of front roll vine picking, rear roll vine killing and rod bar lifting. The key components of the vine picking device, vine killing device and lifting device were designed and calculated. A numerical simulation test of the vine harvesting process was carried out by using the discrete element numerical simulation method. It was determined that the length of the vine picking rod from the outside to the inside is 175 mm, 150 mm and 105 mm, respectively, and the inclination angle of the end is 160°. There are six vine killing knives on each vine killing knife plate. The inclination of the lifting device is 50°and the conveying speed is 3 m/s. Using the box Behnken experimental design method, taking the vine picking roller speed, vine killing roller speed and ground clearance as the experimental factors, and taking the sweet potato vine harvest rate, stubble height and potato injury rate as the evaluation indexes, a quadratic regression orthogonal test was carried out, the effects of various factors on the evaluation indexes were analyzed, and the experimental factors were optimized and verified. The experimental results showed that the optimal parameter combination is as follows: the rotation speed of vine picking roller should be 716 r/min, the rotation speed of vine killing roller should be 1960 r/min and the ground clearance should be 16 mm. With these parameters, the harvest rate of sweet potato vines is 93.1%, the stubble height is 29.5 mm and the potato injury rate is 0.174%. As such, the harvester meets the requirements for the mechanized harvesting of sweet potato vines and is of great significance as a light and simplified product for the sweet potato industry.

Collision of falling in the mechanical harvesting process of sweet potato is one of the main causes of epidermal destruction and damage to sweet potato tubers. Therefore, a sweet potato mechanical characteristic test and a full-factor sweet potato drop test were designed. Based on the analysis of the fitting mathematical model, the impact of the drop height, collision material and sweet potato chunk size on the damage of the sweet potato were studied. The mathematical models were established by fitting analysis of the IBM SPSS Statistics 22 software between the drop height and the sweet potato chunk size with each test index (impact force, impact stress, broken skin area and damaged area). The critical epidermal destruction height and the critical damage height of a certain size of sweet potato when it collides with a collision material can be calculated by the mathematical model, and the critical epidermal destruction mass and critical damage mass of sweet potato when it falls from a certain height and collides with a collision material can also be calculated. Then a series of critical values (including critical epidermal destruction force value, critical epidermal destruction impact stress, critical damage force value, critical damage impact stress) of mechanical properties of sweet potato were obtained. The results show that the impact deformation of sweet potato includes both elastic and plastic ones, and has similar stress relaxation characteristics. The critical damage impact stress of sweet potato is that the average value of the impact stress on the contact surface is less than it's Firmness. The results provided a theoretical basis for understanding the collision damage mechanism of sweet potato and how to reduce the damage during harvest.

Spinon excitations of a Kagome quantum spin liquid are expected to give rise to a magnetic continuum in Raman spectroscopy. Here, the authors report a magnetic Raman continuum in the Kagome spin liquid candidate Cu3Zn(OH)6FBr, in contrast to a sharp magnon Raman peak in the Kagome antiferromagnet EuCu3(OH)6Cl3.

In order to meet the challenge of high loss rate and high tuber injury rate during the operation of the 4UZL-1 sweet potato combine harvester, the sweet potato tuber hand-over lifting mechanism was designed based on a comprehensive analysis of the entire structure of the harvester. Taking the average normal force on conveying sweet potato tubers as evaluation indexes, the EDEM simulation experiment was carried out considering the factors of the angle of the excavating and conveying mechanism, the conveying angle of the scraper chain, the speed of the excavating and conveying mechanism, and the speed of the scraper chain conveying. The experimental findings indicated that the optimal operational performance of the hand-over lifting mechanism was achieved at a speed of 1.15 m/s for the excavating and conveying mechanism, an angle of 24° for the excavating and conveying mechanism, a conveying speed of 0.66 m/s for the scraper chain, and a conveying angle of 60° for the scraper chain. Field experiments were conducted based on the EDEM simulation experiment, using the loss rate and the injury rate of conveying sweet potato tubers as evaluation indexes. The results showed that the hand-over lifting mechanism demonstrated optimal operational effectiveness with an excavating and conveying mechanism angle of 20°, a scraper chain angle of 68°, an excavating and conveying mechanism speed of 1.2 m/s, and a scraper chain speed of 0.66 m/s, while the machine running speed was maintained at 1 m/s. At the moment, the hand-over lifting structure exhibited a loss rate of 1.12% and a tuber injury rate of 0.94%. The conclusions obtained serve as a valuable reference for future research and optimization of sweet potato combines. [ABSTRACT FROM AUTHOR]