Search

Resin-based friction materials (RBFMs) strengthened by polyether ether ketone (PEEK) fiber were designed and prepared in this study. Specimens incorporating PEEK fiber of 2–8 wt.% were fabricated based on wet granulation, and then the effects of the PEEK fiber content on the mechanical and tribological properties of RBFMs were systematically investigated. The results showed that PEEK fiber can sense the braking temperature and then effectively regulate the comprehensive properties of RBFMs. The specimen incorporating 6 wt.% PEEK fiber obtained the optimal comprehensive performance with a stable friction coefficient (COF), excellent fade resistance and recovery properties, and better wear resistance. The worn surface was inspected using a scanning electron microscope. After the friction–wear test, the specimen with 6 wt.% PEEK fiber presented a number of primary and secondary plateaus and a reduced number of pits with wear debris on the worn surface. The study indicated that PEEK fiber could not only enhance the mechanical and tribological properties of RBFMs at low temperatures because of their high strength and self-lubrication but also adhere to wear debris to reduce abrasive wear at high temperatures; furthermore, the adhered wear debris could form a secondary plateau under normal pressure, which could alleviate abrasion. [ABSTRACT FROM AUTHOR]

Resin-based friction materials (RBFM) are widely used in the fields of automobiles, agriculture machinery and engineering machinery, and they are vital for safe and stable operation. In this paper, polymer ether ketone (PEEK) fibers were added to RBFM to enhance its tribological properties. Specimens were fabricated by wet granulation and hot-pressing. The relationship between intelligent reinforcement PEEK fibers and tribological behaviors was investigated by a JF150F-II constant-speed tester according to GB/T 5763-2008, and the worn surface morphology was observed using an EVO-18 scanning electron microscope. The results showed that PEEK fibers can efficiently enhance the tribological properties of RBFM. A specimen with 6 ωt% PEEK fibers obtained the optimal tribological performance, the fade ratio was −6.2%, which was much higher than that of the specimen without the addition of PEEK fibers, the recovery ratio was 108.59% and the wear rate was the lowest, which was 1.497 × 10−7 cm3/(Nm)−1. The reason for the enhancing tribological performance was that, on the one hand, PEEK fibers have a high strength and modulus which can enhance the specimens at lower temperatures; on the other hand, molten PEEK at high temperatures can also promote the formation of secondary plateaus, which are beneficial for friction. The results in this paper can lay a foundation for future studies on intelligent RBFM. [ABSTRACT FROM AUTHOR]

Because of the excellent thermal conduction, corrosion resistance, and tribological properties, copper-based friction materials (CBFMs) were widely used in airplanes, high-speed trains, and wind power generation. With operating speed continuously increasing, CBFMs are suffering more complicated and extreme working conditions, which would cause abnormal abrasion. This paper presents an experiment to investigate how the tribological behaviors of CBFMs are regulated by granulation technology. Samples were prepared by the method of granulation and cool-pressed sinter. The tribological properties of specimens with different granule sizes were studied. The results showed that granulation could improve the tribological properties of CBFMs. The friction coefficient (COF) increased first and then decreased with increasing granule size. Specimen fabricated with 5–8 mm granules obtained the lowest COF, which was reduced by 22.49% than that made of powders. Moreover, the wear rate decreased first and then increased as granule size increased. The wear rate of samples prepared by granules 3–5 mm was lower than that of all of the other samples. This is because the structured samples prepared by wet granulation can promote the formation of secondary plateaus, which are beneficial for enhancing tribological properties. This makes granulation a promising method for enhancing the tribological performances of CBFMs. [ABSTRACT FROM AUTHOR]

Background: Ergothioneine (EGT) is a distinctive sulfur-containing histidine derivative, which has been recognized as a high-value antioxidant and cytoprotectant, and has a wide range of applications in food, medical, and cosmetic fields. Currently, microbial fermentation is a promising method to produce EGT as its advantages of green environmental protection, mild fermentation condition, and low production cost. However, due to the low-efficiency biosynthetic process in numerous cell factories, it is still a challenge to realize the industrial biopreparation of EGT. The non-conventional yeast Rhodotorula toruloides is considered as a potential candidate for EGT production, thanks to its safety for animals and natural ability to synthesize EGT. Nevertheless, its synthesis efficiency of EGT deserves further improvement. Results: In this study, out of five target wild-type R. toruloides strains, R. toruloides 2.1389 (RT1389) was found to accumulate the highest EGT production, which could reach 79.0 mg/L at the shake flask level on the 7th day. To achieve iterative genome editing in strain RT1389, CRISPR-assisted Cre recombination (CACR) method was established. Based on it, an EGT-overproducing strain RT1389-2 was constructed by integrating an additional copy of EGT biosynthetic core genes RtEGT1 and RtEGT2 into the genome, the EGT titer of which was 1.5-fold increase over RT1389. As the supply of S-adenosylmethionine was identified as a key factor determining EGT production in strain RT1389, subsequently, a series of gene modifications including S-adenosylmethionine rebalancing were integrated into the strain RT1389-2, and the resulting mutants were rapidly screened according to their EGT production titers with a high-throughput screening method based on ergothionase. As a result, an engineered strain named as RT1389-3 was selected with a production titer of 267.4 mg/L EGT after 168 h in a 50 mL modified fermentation medium. Conclusions: This study characterized the EGT production capacity of these engineered strains, and demonstrated that CACR and high-throughput screening method allowed rapid engineering of R. toruloides mutants with improved EGT production. Furthermore, this study provided an engineered RT1389-3 strain with remarkable EGT production performance, which had potential industrial application prospects. [ABSTRACT FROM AUTHOR]

β-tricalcium phosphate has good biodegradability and biocompatibility; it is widely perceived as a good material for treating bone deficiency. In this research, different contents of strontium (Sr) and silver (Ag) ion-doped β-tricalcium phosphate powders were prepared using the sol–gel method. After obtaining the best ratio of pore-forming agent and binder, the as-synthesized powders were sintered in a muffle for 5 h at 1000 °C to obtain the samples. Then, these samples were degraded in vitro in simulated body fluids. The samples were tested using a series of characterization methods before and after degradation. Results showed that the amount of Sr and/or Ag doping had an effect on the crystallinity and structural parameters of the samples. After degradation, though the compressive strength of these samples decreased overall, the compressive strength of the undoped samples was higher than that of the doped samples. Notably, apatite-like materials were observed on the surface of the samples. All the results indicate that Sr and/or Ag β-TCP has good osteogenesis and proper mechanical properties; it will be applied as a prospective biomaterial in the area of bone repair. [ABSTRACT FROM AUTHOR]

Subsoiling technology is an important method in conservation tillage. The effect that the plough pan was broken by bionic subsoiler was successfully simulated by EDEM in this paper. The force of mole's paw in soil excavation was first analyzed by mathematical model, and then bionic subsoiler meeting the excavation requirements was designed by combining the structure of mole's claw with standard subsoiler. The breaking situation of plough pan and the stress state of the subsoiler were analyzed in EDEM and verified in both soil bin test and field test. The results showed that the bionic subsoilers could effectively improve the breakage effect of the plough pan, and the greater the width of disturbance of plough pan was and the better the subsoiling effect was. Compared with standard subsoiler, the soil looseness of the plough pan formed by bionic subsoiler-C increased by 18.2% at the tillage depth of 300 mm, 20.0% at the tillage depth of 380 mm and 20.6% at the tillage depth of 460 mm, respectively. The Critical depth of subsoiling was 380 mm, where the best breakage effect of plough pan and soil looseness of the soil layer were obtained at low energy consumption. Soil bin and field tests could prove that the bionic design of the subsoiler decreased the draft force, and increased the width of disturbance of plough pan, which was consistent with the analysis results of EDEM. The bionic subsoilers could better break the plough pan and improve the farming quality of the soil. [Display omitted] • The breakage effect of the plough pan layer by bionic subsoiler was successfully simulated by EDEM. • Bionic subsoiler was designed by combining the structure of mole's claw with standard subsoiler. • Bionic subsoilers effectively improved the breakage efficiency of the plough pan layer and reduce tillage resistance. • Bionic subsoiler-C could better loosen the soil and promote the growth of plant roots. [ABSTRACT FROM AUTHOR]