Search

We present the creation of a lithium-cesium slow beam using a two-dimensional magneto-optical trap. The two-species atomic beam is directed to load a three-dimensional magneto-optical trap in ultrahigh vacuum. We achieve a loading rate of 1.3$\times$10$^{7}$ lithium atoms/s with the lithium oven temperature at 370~$^{\circ}$C and 2.2$\times$10$^{7}$ cesium atoms/s with the Cs oven temperature at 20~$^{\circ}$C. The maximum numbers of lithium and cesium atoms in the trap are 1.0$\times$10$^{9}$ and 1.4$\times$10$^{8}$, respectively. Our results show that the simple and compact two-dimensional magneto-optical trap is suitable for producing an atomic beam of two species that have a large mass ratio and very different volatilities., Comment: 7 pages, 7 figures

Y-Ba-Cu-O (YBCO) and Sm-Ba-Cu-O (SmBCO) thin films have been used for the first time as heterogeneous seeds to multi-seed successfully the melt growth of bulk YBCO in a multi-seeded melt growth (MSMG) process. The use of thin film seeds, which may be prepared with highly controlled orientation (i.e. with a well-defined a-b plane and precisely known a-direction), is based on their superheating properties and reduces significantly contamination of the bulk sample by the seed material. A variety of grain boundaries were obtained by varying the angle between the seeds. Microstructural studies indicate that the extent of residual melt deposited at the grain boundary decreases with increasing grain boundary contact angle. It is established that the growth front proceeds continuously at the (110)/(110) grain boundary without trapping liquid, which leads to the formation of a clean grain boundary.

La2Zr2O7 (LZO) formation of bulk powders and of films by Chemical Solution Deposition (CSD) process have been studied using propionates. The treatment involved a one step cycle in the reducing forming gas (Ar-5%H2) to be compatible with Ni-5at%W RABITS. Large amount of residual carbon was found in LZO powders formed in these conditions (10 wt %). The volume fraction of the cube texture in LZO films on Ni-5at%w RABITS was found to be a function of the speed of the gas flown above sample. This phenomenon is discussed in considering the C deposited from the carbon-containing gases emitted during the pyrolysis of the precursor. Using proper conditions (950 ^\circC and the speed of gas of 6.8\times10^{-2} m/s), LZO films with good surface crystallinity could be obtained on Ni-5at%W RABITS as demonstrated by X-ray diffraction, electron backscattered diffraction and RHEED. The existence of residual carbon in oxide films is a common question to films deposited by CSD processes under reducing condition.

The MgB2 bulks were prepared by high energy milling of Mg and B powder. The correlations among milling times, microstructure and superconducting properties were investigated in MgB2 bulks. Samples were characterized by x-ray diffraction (XRD), energy dispersive spectrometry (EDX) and scanning electron microscope (SEM), and the magnetization properties were examined by a Superconducting quantum interfere device (SQUID) magnetometer. It showed that the high energy milling is an effective approach to get fine crystalline (40-100nm) bulk MgB2 with good grain connectivity and high Jc performance. The critical current density reaches to 2.0X10E6A/cm2 at 15K and 0.59T, 5.7X10E5A/cm2 at 2T and 3.0X10E4A/cm2 at 5T., Comment: 12 pages, 6 figures

The powder-in-tube MgB2 wires were prepared by high energy milling of Mg and B powder. The powder was not mechanically alloyed for 2h short milling time. However, the MgB2 grains in wires are very small (20 100nm) and resembled to the dimple after post-heat treatment. The clear evidence for transcrystlline fracture is observed. It indicated that the grain connection was greatly improved and the fluxing pinning was significantly enhanced. Another point to view is no intermediate annealing was adopted during the whole rolling process. The influence of the post-heat treatment on the transport current density was studied. Despite the lower Tc of about 35K, the transport current density reaches to 3X10E4A/cm2 at 15K and 3.5T for 700 sintered wires., Comment: 11 pages, 6 figures

We succeeded in the synthesis of high-Jc MgB2 bulks via high energy ball-milling of elemental Mg and B powder at ambient temperatures. Alternatively to longtime mechanical alloying technique, the mixed powder was ball-milled for only 1h and the completed reaction is achieved by subsequent annealing. The correlations among synthesis parameters, microstructures and superconducting properties in MgB2 bulks were investigated. Samples were characterized by XRD and SEM, and the magnetization properties were examined in a SQUID magnetometer. The high- Jc, approximately 1.7*106A/cm2(15K, 0.59T), and improved flux pinning were attribute to a large number of grain boundaries provided by small grain size., Comment: 19 pages, 12 figures,figure9 is replaced for it repeats with figure 10 by mistake

This talk is a brief review of the recent studies on probing new physics through single top quark processes and probing exotic top quark decays at the upgraded Tevatron., Comment: Talk presented by J. M. Yang at the Top Quark Working Group at the Workshop on Physics at the First Muon Collider, Nov. 6-9, 1997, FNAL

The top group studied discovery issues as well as measurements to be made at the Tevatron, the LHC and the SSC., Comment: 11 pages, LaTeX