180 results on '"Li, Anhai"'
Search Results
2. Chip formation and removal mechanisms in cutting of cortical bones with heterogeneous tissue structures
3. Modeling and verification of cortical bone drilling forces based on tissue structure heterogeneity
4. Adjusting machined surface integrity of aluminum–silicon alloy through step-by-step feed cutting and multi-step finish cutting method
5. Effect of machined surface integrity on fatigue resistance of aluminum-silicon alloy ZL109
6. Effect of cutting process adjustment on crystallographic texture of machined surface layer of titanium alloy
7. Effect of surface roughness on stress concentration factor of machined surface and cutting parameter optimization in boring of Al-Si piston alloy
8. Step-dependent grain refinement and micro-harness evolution during chip formation process in orthogonal cutting of titanium alloy Ti-6Al-4V
9. Surface quality adjustment and controlling mechanism of machined surface layer in two-step milling of titanium alloy
10. Effect of alloying elements on surface temperature field of aluminum piston in diesel engine
11. Simulation Study on Residual Stress Distribution of Machined Surface Layer in Two-Step Cutting of Titanium Alloy.
12. Cutting performance and wear mechanisms of TiAlN PVD-coated cemented carbide tool in high speed turning of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy
13. Effect of cutting parameters and tool rake angle on the chip formation and adiabatic shear characteristics in machining Ti-6Al-4V titanium alloy
14. Surface integrity enhancement of ZL109 aluminum-silicon piston alloy employing the forward and reverse finish cutting method
15. Crystallographic texture evolution and tribological behavior of machined surface layer in orthogonal cutting of Ti-6Al-4V alloy
16. Laser Processing and Multi-Energy Field Manufacturing of High-Performance Materials
17. Finite element simulation study on pre-stress multi-step cutting of Ti-6Al-4V titanium alloy
18. FEM simulation-based cutting parameters optimization in machining aluminum-silicon piston alloy ZL109 with PCD tool
19. FEM-simulation of machining induced surface plastic deformation and microstructural texture evolution of Ti-6Al-4V alloy
20. Effects of initial particle size distribution and sintering parameters on microstructure and mechanical properties of functionally graded WC-TiC-VC-Cr3C2-Co hard alloys
21. Serrated chip formation mechanism analysis for machining of titanium alloy Ti-6Al-4V based on thermal property
22. Effect of cutting parameters on surface quality in multi-step turning of Ti-6Al-4V titanium alloy
23. Preparation of In Situ Growth Multiscale β-Sialon Grain-Reinforced Al2O3-Based Composite Ceramic Tool Materials
24. Optimization of Forged 42CrMo4 Steel Piston Pin Hole Profile Using Finite Element Method
25. Effect of cutting process adjustment on crystallographic texture of machined surface layer of titanium alloy
26. Microstructure and Properties of WC/Ni-Based Laser-Clad Coatings with Different WC Content Values
27. Application of Deep Learning on the Prognosis of Cutaneous Melanoma Based on Full Scan Pathology Images
28. Surface Properties of Medium-Entropy Alloy Coatings Prepared through a Combined Process of Laser Cladding and Ultrasonic Burnishing
29. Optimal selection of cutting tool materials based on multi-criteria decision-making methods in machining Al-Si piston alloy
30. Design and simulation of thermal residual stresses of coatings on WC-Co cemented carbide cutting tool substrate
31. Coated carbide tool failure analysis in high-speed intermittent cutting process based on finite element method
32. Three-point bending fatigue behavior of WC–Co cemented carbides
33. Preparation of In Situ Growth Multiscale β-Sialon Grain-Reinforced Al 2 O 3 -Based Composite Ceramic Tool Materials.
34. Effects of cutting conditions on microhardness and microstructure in high-speed milling of H13 tool steel
35. Simulation-based solid carbide end mill design and geometry optimization
36. Performance evaluation of ultra-fine grain carbide in high-speed milling of Ti-6Al-4V
37. Effect of Surface Micro-Hardness Change in Multistep Machining on Friction and Wear Characteristics of Titanium Alloy
38. Performance of graded nano-composite ceramic tools in ultra-high-speed milling of Inconel 718
39. Failure mechanisms of a PCD tool in high-speed face milling of Ti–6Al–4V alloy
40. Failure mechanisms of graded ceramic tool in ultra high speed dry milling of Inconel 718
41. Effects of inclination angles on geometrical features of machined surface in five-axis milling
42. Experimental investigation on chip morphologies in high-speed dry milling of titanium alloy Ti-6Al-4V
43. Investigation on ball end milling of P20 die steel with cutter orientation
44. Progressive tool failure in high-speed dry milling of Ti-6Al-4V alloy with coated carbide tools
45. Mining database for the clinical significance and prognostic value of CBX family in skin cutaneous melanoma
46. Tool condition monitoring in milling process using multifractal detrended fluctuation analysis and support vector machine
47. Dry wear characteristics of machined ZL109 aluminum-silicon alloy surface under unidirectional and reciprocating rolling-contact friction
48. Abrasive wear characteristics of 40Mn2 steel in simulated condition of sprocket wheel in crawler bulldozer walking system
49. Study of Chip Morphology and Chip Formation Mechanism During Machining of Magnesium-Based Metal Matrix Composites
50. Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V
Catalog
Books, media, physical & digital resources
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.